Red Hat Enterprise Linux 5

DM Multipath
DM Multipath Configuration and Administration
DM Multipath

Red Hat Enterprise Linux 5 DM Multipath

DM Multipath Configuration and Administration
Edition 3

Copyright © 2009 Red Hat, Inc. This material may only be distributed subject to the terms and
conditions set forth in the Open Publication License, V1.0 or later (the latest version of the OPL is
presently available at http://www.opencontent.org/openpub/).

Red Hat and the Red Hat "Shadow Man" logo are registered trademarks of Red Hat, Inc. in the United
States and other countries.

All other trademarks referenced herein are the property of their respective owners.

1801 Varsity Drive

Raleigh, NC 27606-2072 USA
Phone: +1 919 754 3700
Phone: 888 733 4281
Fax: +1 919 754 3701
PO Box 13588 Research Triangle Park, NC 27709 USA

This book provides information on using the Device-Mapper Multipath feature of Red Hat Enterprise
Linux 5
Preface v
1. Audience ........................................................................................................................ v
2. Related Documentation ................................................................................................... v
3. Feedback ....................................................................................................................... vi
4. Document Conventions ................................................................................................... vi
4.1. Typographic Conventions ..................................................................................... vi
4.2. Pull-quote Conventions ....................................................................................... viii
4.3. Notes and Warnings ........................................................................................... viii
1. Device Mapper Multipathing 1
1.1. Overview of DM-Multipath ............................................................................................. 1
1.2. Storage Array Support .................................................................................................. 3
1.3. DM-Multipath Components ............................................................................................ 3
1.4. DM-Multipath Setup Overview ....................................................................................... 4
2. Multipath Devices 5
2.1. Multipath Device Identifiers ........................................................................................... 5
2.2. Consistent Multipath Device Names in a Cluster ............................................................ 5
2.3. Multipath Device Attributes ........................................................................................... 6
2.4. Multipath Devices in Logical Volumes ............................................................................ 6
3. Setting Up DM-Multipath 7
3.1. Setting Up DM-Multipath ............................................................................................... 7
3.2. Ignoring Local Disks when Generating Multipath Devices ................................................ 8
3.3. Adding Devices to the Multipathing Database ............................................................. 10
4. The DM-Multipath Configuration File 11
4.1. Configuration File Overview ........................................................................................ 11
4.2. Configuration File Blacklist .......................................................................................... 12
4.2.1. Blacklisting by WWID ....................................................................................... 12
4.2.2. Blacklisting By Device Name ............................................................................ 12
4.2.3. Blacklisting By Device Type ............................................................................. 13
4.2.4. Blacklist Exceptions ......................................................................................... 13
4.3. Configuration File Defaults .......................................................................................... 14
4.4. Multipaths Device Configuration Attributes ................................................................... 17
4.5. Configuration File Devices .......................................................................................... 18
5. DM-Multipath Administration and Troubleshooting 23
5.1. Resizing an Online Multipath Device ........................................................................... 23
5.2. The Multipath Daemon ............................................................................................... 24
5.3. Issues with Large Number of LUNs ............................................................................. 24
5.4. Issues with queue_if_no_path feature .......................................................................... 24
5.5. Multipath Command Output ........................................................................................ 25
5.6. Multipath Queries with multipath Command ................................................................. 25
5.7. Multipath Command Options ....................................................................................... 26
5.8. Determining Device Mapper Entries with the dmsetup Command ................................... 26
5.9. Troubleshooting with the multipathd Interactive Console ................................................ 27
A. Revision History 29
Index 31

iii
iv
Preface
This book describes the Device Mapper Multipath (DM-Multipath) feature of Red Hat Enterprise Linux
for the RHEL 5 release.

1. Audience
This book is intended to be used by system administrators managing systems running the Linux
operating system. It requires familiarity with Red Hat Enterprise Linux.

2. Related Documentation
For more information about using Red Hat Enterprise Linux, refer to the following resources:

• Red Hat Enterprise Linux Installation Guide — Provides information regarding installation of Red
Hat Enterprise Linux 5.

• Red Hat Enterprise Linux Deployment Guide — Provides information regarding the deployment,
configuration and administration of Red Hat Enterprise Linux 5.

For more information about Red Hat Cluster Suite for Red Hat Enterprise Linux 5, refer to the following
resources:

• Red Hat Cluster Suite Overview — Provides a high level overview of the Red Hat Cluster Suite.

• Configuring and Managing a Red Hat Cluster — Provides information about installing, configuring
and managing Red Hat Cluster components.

• Logical Volume Manager Administration — Provides a description of the Logical Volume Manager
(LVM), including information on running LVM in a clustered environment.

• Global File System: Configuration and Administration — Provides information about installing,
configuring, and maintaining Red Hat GFS (Red Hat Global File System).

• Global File System 2: Configuration and Administration — Provides information about installing,
configuring, and maintaining Red Hat GFS2 (Red Hat Global File System 2).

• Using GNBD with Global File System — Provides an overview on using Global Network Block
Device (GNBD) with Red Hat GFS.

• Linux Virtual Server Administration — Provides information on configuring high-performance

systems and services with the Linux Virtual Server (LVS).

• Red Hat Cluster Suite Release Notes — Provides information about the current release of Red Hat
Cluster Suite.

Red Hat Cluster Suite documentation and other Red Hat documents are available in HTML,
PDF, and RPM versions on the Red Hat Enterprise Linux Documentation CD and online at http://
www.redhat.com/docs/.

v
Preface

3. Feedback
If you spot a typo, or if you have thought of a way to make this manual better, we would love to
hear from you. Please submit a report in Bugzilla (http://bugzilla.redhat.com/bugzilla/) against the
component rh-cs.

Be sure to mention the manual's identifier:

Bugzilla component: Documentation-cluster

Book identifier: DM_Multipath(EN)-5 (2009-08-18T15:35)

By mentioning this manual's identifier, we know exactly which version of the guide you have.

If you have a suggestion for improving the documentation, try to be as specific as possible. If you have
found an error, please include the section number and some of the surrounding text so we can find it
easily.

4. Document Conventions
This manual uses several conventions to highlight certain words and phrases and draw attention to
specific pieces of information.
1
In PDF and paper editions, this manual uses typefaces drawn from the Liberation Fonts set. The
Liberation Fonts set is also used in HTML editions if the set is installed on your system. If not,
alternative but equivalent typefaces are displayed. Note: Red Hat Enterprise Linux 5 and later includes
the Liberation Fonts set by default.

4.1. Typographic Conventions

Four typographic conventions are used to call attention to specific words and phrases. These
conventions, and the circumstances they apply to, are as follows.

Mono-spaced Bold

Used to highlight system input, including shell commands, file names and paths. Also used to highlight
key caps and key-combinations. For example:

To see the contents of the file my_next_bestselling_novel in your current

working directory, enter the cat my_next_bestselling_novel command at the
shell prompt and press Enter to execute the command.

The above includes a file name, a shell command and a key cap, all presented in Mono-spaced Bold
and all distinguishable thanks to context.

Key-combinations can be distinguished from key caps by the hyphen connecting each part of a key-
combination. For example:

Press Enter to execute the command.

Press Ctrl-Alt-F1 to switch to the first virtual terminal. Press Ctrl-Alt-F7 to return
to your X-Windows session.
1
https://fedorahosted.org/liberation-fonts/

vi
 Typographic Conventions

The first sentence highlights the particular key cap to press. The second highlights two sets of three
key caps, each set pressed simultaneously.

If source code is discussed, class names, methods, functions, variable names and returned values
mentioned within a paragraph will be presented as above, in Mono-spaced Bold. For example:

File-related classes include filesystem for file systems, file for files, and dir for
directories. Each class has its own associated set of permissions.

Proportional Bold

This denotes words or phrases encountered on a system, including application names; dialogue
box text; labelled buttons; check-box and radio button labels; menu titles and sub-menu titles. For
example:

Choose System > Preferences > Mouse from the main menu bar to launch Mouse
Preferences. In the Buttons tab, click the Left-handed mouse check box and click
Close to switch the primary mouse button from the left to the right (making the mouse
suitable for use in the left hand).

To insert a special character into a gedit file, choose Applications > Accessories
> Character Map from the main menu bar. Next, choose Search > Find… from the
Character Map menu bar, type the name of the character in the Search field and click
Next. The character you sought will be highlighted in the Character Table. Double-
click this highlighted character to place it in the Text to copy field and then click the
Copy button. Now switch back to your document and choose Edit > Paste from the
gedit menu bar.

The above text includes application names; system-wide menu names and items; application-specific
menu names; and buttons and text found within a GUI interface, all presented in Proportional Bold and
all distinguishable by context.

Note the > shorthand used to indicate traversal through a menu and its sub-menus. This is to avoid
the difficult-to-follow 'Select Mouse from the Preferences sub-menu in the System menu of the main
menu bar' approach.

Mono-spaced Bold Italic or Proportional Bold Italic

Whether Mono-spaced Bold or Proportional Bold, the addition of Italics indicates replaceable or
variable text. Italics denotes text you do not input literally or displayed text that changes depending on
circumstance. For example:

To connect to a remote machine using ssh, type ssh [email protected] at

a shell prompt. If the remote machine is example.com and your username on that
machine is john, type ssh [email protected].

The mount -o remount file-system command remounts the named file

system. For example, to remount the /home file system, the command is mount -o
remount /home.

To see the version of a currently installed package, use the rpm -q package
command. It will return a result as follows: package-version-release.

Note the words in bold italics above — username, domain.name, file-system, package, version and
release. Each word is a placeholder, either for text you enter when issuing a command or for text
displayed by the system.

vii
Preface

Aside from standard usage for presenting the title of a work, italics denotes the first use of a new and
important term. For example:

When the Apache HTTP Server accepts requests, it dispatches child processes
or threads to handle them. This group of child processes or threads is known as
a server-pool. Under Apache HTTP Server 2.0, the responsibility for creating and
maintaining these server-pools has been abstracted to a group of modules called
Multi-Processing Modules (MPMs). Unlike other modules, only one module from the
MPM group can be loaded by the Apache HTTP Server.

4.2. Pull-quote Conventions

Two, commonly multi-line, data types are set off visually from the surrounding text.

Output sent to a terminal is set in Mono-spaced Roman and presented thus:

books Desktop documentation drafts mss photos stuff svn

books_tests Desktop1 downloads images notes scripts svgs

Source-code listings are also set in Mono-spaced Roman but are presented and highlighted as
follows:

package org.jboss.book.jca.ex1;

import javax.naming.InitialContext;

public class ExClient

{
public static void main(String args[])
throws Exception
{
InitialContext iniCtx = new InitialContext();
Object ref = iniCtx.lookup("EchoBean");
EchoHome home = (EchoHome) ref;
Echo echo = home.create();

System.out.println("Created Echo");

System.out.println("Echo.echo('Hello') = " + echo.echo("Hello"));

}

4.3. Notes and Warnings

Finally, we use three visual styles to draw attention to information that might otherwise be overlooked.

viii
 Notes and Warnings

Note
A Note is a tip or shortcut or alternative approach to the task at hand. Ignoring a note
should have no negative consequences, but you might miss out on a trick that makes your
life easier.

Important
Important boxes detail things that are easily missed: configuration changes that only
apply to the current session, or services that need restarting before an update will apply.
Ignoring Important boxes won't cause data loss but may cause irritation and frustration.

Warning
A Warning should not be ignored. Ignoring warnings will most likely cause data loss.

ix
x
Chapter 1.

Device Mapper Multipathing

Device Mapper Multipathing (DM-Multipath) allows you to configure multiple I/O paths between server
nodes and storage arrays into a single device. These I/O paths are physical SAN connections that can
include separate cables, switches, and controllers. Multipathing aggregates the I/O paths, creating a
new device that consists of the aggregated paths.

1.1. Overview of DM-Multipath

DM-Multipath can be used to provide:

• Redundancy

DM-Multipath can provide failover in an active/passive configuration. In an active/passive

configuration, only half the paths are used at any time for I/O. If any element of an I/O path (the
cable, switch, or controller) fails, DM-Multipath switches to an alternate path.

• Improved Performance

DM-Multipath can be configured in active/active mode, where I/O is spread over the paths in a
round-robin fashion. In some configurations, DM-Multipath can detect loading on the I/O paths and
dynamically re-balance the load.

Figure 1.1, “Active/Passive Multipath Configuration with One RAID Device” shows an active/passive
configuration with two I/O paths from the server to a RAID device. There are 2 HBAs on the server, 2
SAN switches, and 2 RAID controllers.

Figure 1.1. Active/Passive Multipath Configuration with One RAID Device

In this configuration, there is one I/O path that goes through hba1, SAN1, and controller 1 and a
second I/O path that goes through hba2, SAN2, and controller2. There are many points of possible
failure in this configuration:

1
Chapter 1. Device Mapper Multipathing

• HBA failure

• FC cable failure

• SAN switch failure

• Array controller port failure

With DM-Multipath configured, a failure at any of these points will cause DM-Multipath to switch to the
alternate I/O path.

Figure 1.2, “Active/Passive Multipath Configuration with Two RAID Devices” shows a more complex
active/passive configuration with 2 HBAs on the server, 2 SAN switches, and 2 RAID devices with 2
RAID controllers each.

Figure 1.2. Active/Passive Multipath Configuration with Two RAID Devices

In the example shown in Figure 1.2, “Active/Passive Multipath Configuration with Two RAID Devices”,
there are two I/O paths to each RAID device (just as there are in the example shown in Figure 1.1,
“Active/Passive Multipath Configuration with One RAID Device”). With DM-Multipath configured, a
failure at any of the points of the I/O path to either of the RAID devices will cause DM-Multipath to
switch to the alternate I/O path for that device.

Figure 1.3, “Active/Active Multipath Configuration with One RAID Device” shows an active/active
configuration with 2 HBAs on the server, 1 SAN switch, and 2 RAID controllers. There are four I/O
paths from the server to a storage device:

• hba1 to controller1

• hba1 to controller2

• hba2 to controller1

• hba2 to controller2

2
 Storage Array Support

In this configuration, I/O can be spread among those four paths.

Figure 1.3. Active/Active Multipath Configuration with One RAID Device

1.2. Storage Array Support

By default, DM-Multipath includes support for the most common storage arrays that support DM-
Multipath. The supported devices can be found in the multipath.conf.defaults file. If your
storage array supports DM-Multipath and is not configured by default in this file, you may need to add
them to the DM-Multipath configuration file, multipath.conf. For information on the DM-Multipath
configuration file, see Chapter 4, The DM-Multipath Configuration File.

Some storage arrays require special handling of I/O errors and path switching. These require separate
hardware handler kernel modules.

1.3. DM-Multipath Components

Table 1.1, “DM-Multipath Components”. describes the components of DM-Multipath.

Component Description
dm-multipath kernel module Reroutes I/O and supports failover for paths and path groups.
multipath command Lists and configures multipath devices. Normally started up
with /etc/rc.sysinit, it can also be started up by a udev
program whenever a block device is added or it can be run by the
initramfs file system.
multipathd daemon Monitors paths; as paths fail and come back, it may initiate path
group switches. Provides for interactive changes to multipath
devices. This must be restarted for any changes to the /etc/
multipath.conf file.

3
Chapter 1. Device Mapper Multipathing

Component Description
kpartx command Creates device mapper devices for the partitions on a device It is
necessary to use this command for DOS-based partitions with DM-
MP. The kpartx is provided in its own package, but the device-
mapper-multipath package depends on it.
Table 1.1. DM-Multipath Components

1.4. DM-Multipath Setup Overview

DM-Multipath includes compiled-in default settings that are suitable for common multipath
configurations. Setting up DM-multipath is often a simple procedure.

The basic procedure for configuring your system with DM-Multipath is as follows:

1. Install device-mapper-multipath rpm.

2. Edit the multipath.conf configuration file:

• comment out the default blacklist

• change any of the existing defaults as needed

• save the configuration file

3. Start the multipath daemons.

4. Create the multipath device with the multipath command.

Detailed setup instructions for several example multipath configurations are provided in see Chapter 3,
Setting Up DM-Multipath.

4
Chapter 2.

Multipath Devices
Without DM-Multipath, each path from a server node to a storage controller is treated by the system
as a separate device, even when the I/O path connects the same server node to the same storage
controller. DM-Multipath provides a way of organizing the I/O paths logically, by creating a single
multipath device on top of the underlying devices.

2.1. Multipath Device Identifiers

Each multipath device has a World Wide Identifier (WWID), which is guaranteed to be globally unique
and unchanging. By default, the name of a multipath device is set to its WWID. Alternately, you can set
the user_friendly_names option in the multipath configuration file, which sets the alias to a node-
unique name of the form mpathn.

For example, a node with two HBAs attached to a storage controller with two ports via a single
unzoned FC switch sees four devices: /dev/sda, /dev/sdb, dev/sdc, and /dev/sdd. DM-
Multipath creates a single device with a unique WWID that reroutes I/O to those four underlying
devices according to the multipath configuration. When the user_friendly_names configuration
option is set to yes, the name of the multipath device is set to mpathn.

When new devices are brought under the control of DM-Multipath, the new devices may be seen in
three different places under the /dev directory: /dev/mapper/mpathn, /dev/mpath/mpathn, and
/dev/dm-n.

• The devices in /dev/mapper are created early in the boot process. Use these devices to access
the multipathed devices, for example when creating logical volumes.

• The devices in /dev/mpath are provided as a convenience so that all multipathed devices can
be seen in one directory. These devices are created by the udev device manager and may not be
available on startup when the system needs to access them. Do not use these devices for creating
logical volumes or filesystems.

• Any devices of the form /dev/dm-n are for internal use only and should never be used.

For information on the multipath configuration defaults, including the user_friendly_names

configuration option, see Section 4.3, “Configuration File Defaults”.

You can also set the name of a multipath device to a name of your choosing by using the alias
option in the multipaths section of the multipath configuration file. For information on the
multipaths section of the multipath configuration file, see Section 4.4, “Multipaths Device
Configuration Attributes”.

2.2. Consistent Multipath Device Names in a Cluster

When the user_friendly_names configuration option is set to yes, the name of the multipath
device is unique to a node, but it is not guaranteed to be the same on all nodes using the multipath
device. This should not cause any difficulties if you use LVM to create logical devices from the
multipath device, but if you require that your multipath device names be consistent in every node in the
cluster you perform one of the following procedures:

• Use the alias option in the multipaths section of the multipath configuration file to set the name
of the multipath device. The alias for the multipath device is consistent across all the nodes in

5
Chapter 2. Multipath Devices

a cluster. For information on the multipaths section of the multipath configuration file, see see
Section 4.4, “Multipaths Device Configuration Attributes”.

• If you want the system-defined user-friendly names to be consistent across all nodes in the cluster,
set up all of the multipath devices on one machine. Then copy the /var/lib/multipath/
bindings file from that machine to all the other machines in the cluster.

2.3. Multipath Device Attributes

In addition to the user_friendly_names and alias options, a multipath device has numerous
attributes. You can modify these attributes for a specific multipath device by creating an entry for
that device in the multipaths section of the multipath configuration file. For information on the
multipaths section of the multipath configuration file, see see Section 4.4, “Multipaths Device
Configuration Attributes”.

2.4. Multipath Devices in Logical Volumes

After creating multipath devices, you can use the multipath device names just as you would use a
physical device name when creating an LVM physical volume. For example, if /dev/mapper/mpath0
is the name of a multipath device, the following command will mark /dev/mapper/mpath0 as a
physical volume.

pvcreate /dev/mapper/mpath0

You can use the resulting LVM physical device when you create an LVM volume group just as you
would use any other LVM physical device.

Note
If you attempt to create an LVM physical volume on a whole device on which you have
configured partitions, the pvcreate command will fail. Note that the Anaconda and
Kickstart installation programs create empty partition tables if you do not specify otherwise
for every block device. If you wish to use the whole device rather than a partition, you
must remove the existing partitions from the device. You can remove existing partitions
with the kpartx -d and the fdisk commands. If your system has block devices that are
greater that 2Tb, you can use the parted command to remove partitions.

When you create an LVM logical volume that uses active/passive multipath arrays as the underlying
physical devices, you should include filters in the lvm.conf to exclude the disks that underlie the
multipath devices. This is because if the array automatically changes the active path to the passive
path when it receives I/O, multipath will failover and failback whenever LVM scans the passive path if
these devices are not filtered. For active/passive arrays that require a command to make the passive
path active, LVM prints a warning message when this occurs.

To filter all SCSI devices in the LVM configuration file (lvm.conf), include the following filter in the
devices section of the file.

filter = [ "r/disk/", "r/sd.*/", "a/.*/" ]

6
Chapter 3.

Setting Up DM-Multipath
This chapter provides step-by-step example procedures for configuring DM-Multipath. It includes the
following procedures:

• Basic DM-Multipath setup

• Ignoring local disks

• Adding more devices to the configuration file

3.1. Setting Up DM-Multipath

Before setting up DM-Multipath on your system, ensure that your system has been updated and
includes the device-mapper-multipath package.

Use the following procedure to set up DM-Multipath for a basic failover configuration.

1. Edit the /etc/multipath.conf file by commenting out the following lines at the top of the file.
This section of the configuration file, in its initial state, blacklists all devices. You must comment it
out to enable multipathing.

blacklist {
devnode "*"
}

After commenting out those lines, this section appears as follows.

# blacklist {
# devnode "*"
# }

2. The default settings for DM-Multipath are compiled in to the system and do not need to be
explicitly set in the /etc/multipath.conf file.

The default value of path_grouping_policy is set to failover, so in this example you do not
need to change the default value. For information on changing the values in the configuration file
to something other than the defaults, see Chapter 4, The DM-Multipath Configuration File.

The initial defaults section of the configuration file configures your system that the names of the
multipath devices are of the form mpathn; without this setting, the names of the multipath devices
would be aliased to the WWID of the device.

3. Save the configuration file and exit the editor.

4. Execute the following commands:

modprobe dm-multipath

7
Chapter 3. Setting Up DM-Multipath

service multipathd start

multipath -v2

The multipath -v2 command prints out multipathed paths that show which devices are
multipathed. If the command does not print anything out, ensure that all SAN connections are set
up properly and the system is multipathed.

For further information on the multipath command output, see Section 5.5, “Multipath
Command Output”.

5. Execute the following command to ensure sure that the multipath daemon starts on bootup:

chkconfig multipathd on

Since the value of user_friendly_name is set to yes in the configuration file the multipath devices
will be created as /dev/mapper/mpathn. For information on setting the name of the device to an
alias of your choosing, see Chapter 4, The DM-Multipath Configuration File.

3.2. Ignoring Local Disks when Generating Multipath

Devices
Some machines have local SCSI cards for their internal disks. DM-Multipath is not recommended for
these devices. The following procedure shows how to modify the multipath configuration file to ignore
the local disks when configuring multipath.

1. Determine which disks are the internal disks and mark them as the ones to blacklist.

In this example, /dev/sda is the internal disk. Note that as originally configured in the default
multipath configuration file, executing the multipath -v2 shows the local disk, /dev/sda, in
the multipath map.

For further information on the multipath command output, see Section 5.5, “Multipath
Command Output”.

[root@rh4cluster1 ~]# multipath -v2

create: SIBM-ESXSST336732LC____F3ET0EP0Q000072428BX1
[size=33 GB][features="0"][hwhandler="0"]
\_ round-robin 0
\_ 0:0:0:0 sda 8:0 [---------

device-mapper ioctl cmd 9 failed: Invalid argument

device-mapper ioctl cmd 14 failed: No such device or address
create: 3600a0b80001327d80000006d43621677
[size=12 GB][features="0"][hwhandler="0"]
\_ round-robin 0
\_ 2:0:0:0 sdb 8:16
\_ 3:0:0:0 sdf 8:80

create: 3600a0b80001327510000009a436215ec

8
 Ignoring Local Disks when Generating Multipath Devices

[size=12 GB][features="0"][hwhandler="0"]
\_ round-robin 0
\_ 2:0:0:1 sdc 8:32
\_ 3:0:0:1 sdg 8:96

create: 3600a0b80001327d800000070436216b3
[size=12 GB][features="0"][hwhandler="0"]
\_ round-robin 0
\_ 2:0:0:2 sdd 8:48
\_ 3:0:0:2 sdh 8:112

create: 3600a0b80001327510000009b4362163e
[size=12 GB][features="0"][hwhandler="0"]
\_ round-robin 0
\_ 2:0:0:3 sde 8:64
\_ 3:0:0:3 sdi 8:128

2. In order to prevent the device mapper from mapping /dev/sda in its multipath maps, edit the
blacklist section of the /etc/multipath.conf file to include this device. Although you could
blacklist the sda device using a devnode type, that would not be safe procedure since /dev/sda
is not guaranteed to be the same on reboot. To blacklist individual devices, you can blacklist using
the WWID of that device.

Note that in the output to the multipath -v2 command, the WWID of the /dev/sda device is
SIBM-ESXSST336732LC____F3ET0EP0Q000072428BX1. To blacklist this device, include the
following in the /etc/multipath.conf file.

blacklist {
wwid SIBM-ESXSST336732LC____F3ET0EP0Q000072428BX1
}

3. After you have updated the /etc/multipath.conf file, you must manually tell the
multipathd daemon to reload the file. The following command reloads the updated /etc/
multipath.conf file.

service multipathd reload

4. Run the following commands:

multipath -F
multipath -v2

The local disk or disks should no longer be listed in the new multipath maps, as shown in the
following example.

[root@rh4cluster1 ~]# multipath -F

9
Chapter 3. Setting Up DM-Multipath

[root@rh4cluster1 ~]# multipath -v2

create: 3600a0b80001327d80000006d43621677
[size=12 GB][features="0"][hwhandler="0"]
\_ round-robin 0
\_ 2:0:0:0 sdb 8:16
\_ 3:0:0:0 sdf 8:80

create: 3600a0b80001327510000009a436215ec
[size=12 GB][features="0"][hwhandler="0"]
\_ round-robin 0
\_ 2:0:0:1 sdc 8:32
\_ 3:0:0:1 sdg 8:96

create: 3600a0b80001327d800000070436216b3
[size=12 GB][features="0"][hwhandler="0"]
\_ round-robin 0
\_ 2:0:0:2 sdd 8:48
\_ 3:0:0:2 sdh 8:112

create: 3600a0b80001327510000009b4362163e
[size=12 GB][features="0"][hwhandler="0"]
\_ round-robin 0
\_ 2:0:0:3 sde 8:64
\_ 3:0:0:3 sdi 8:128

3.3. Adding Devices to the Multipathing Database

By default, DM-Multipath includes support for the most common storage arrays that support DM-
Multipath. The default configuration values, including supported devices, can be found in the
multipath.conf.defaults file.

If you need to add a storage device that is not supported by default as a known multipath device, edit
the /etc/multipath.conf file and insert the appropriate device information.

For example, to add information about the HP Open-V series the entry looks like this:

devices {
device {
vendor "HP"
product "OPEN-V."
getuid_callout "/sbin/scsi_id -g -u -p0x80 -s /block/%n"
}
}

For more information on the devices section of the configuration file, see Section 4.5, “Configuration
File Devices”.

10
Chapter 4.

The DM-Multipath Configuration File

By default, DM-Multipath provides configuration values for the most common uses of multipathing.
In addition, DM-Multipath includes support for the most common storage arrays that support DM-
Multipath. The default configuration values and the supported devices can be found in the /usr/
share/doc/device-mapper-multipath-0.4.7/multipath.conf.defaults file.

You can override the default configuration values for DM-Multipath by editing the /etc/
multipath.conf configuration file. If necessary, you can also add a storage array that is not
supported by default to the configuration file. This chapter provides information on parsing and
modifying the multipath.conf file. It contains sections on the following topics:

• Configuration file overview

• Configuration file blacklist

• Configuration file defaults

• Configuration file multipaths

• Configuration file devices

In the multipath configuration file, you need to specify only the sections that you need
for your configuration, or that you wish to change from the default values specified in the
multipath.conf.defaults file. If there are sections of the file that are not relevant to your
environment or for which you do not need to override the default values, you can leave them
commented out, as they are in the initial file.

The configuration file allows regular expression description syntax.

An annotated version of the configuration file can be found in /usr/share/doc/device-mapper-

multipathd-0.4.7/multipath.conf.annotated.

4.1. Configuration File Overview

The multipath configuration file is divided into the following sections:

blacklist
Listing of specific devices that will not be considered for multipath. By default all devices are
blacklisted. Usually the default blacklist section is commented out.

blacklist_exceptions
Listing of multipath candidates that would otherwise be blacklisted according to the parameters of
the blacklist section.

defaults
General default settings for DM-Multipath.

multipaths
Settings for the characteristics of individual multipath devices. These values overwrite what is
specified in the defaults and devices sections of the configuration file.

11
Chapter 4. The DM-Multipath Configuration File

devices
Settings for the individual storage controllers. These values overwrite what is specified in the
defaults section of the configuration file. If you are using a storage array that is not supported
by default, you may need to create a devices subsection for your array.

When the system determines the attributes of a multipath device, first it checks the multipath settings,
then the per devices settings, then the multipath system defaults.

4.2. Configuration File Blacklist

The blacklist section of the multipath configuration file specifies the devices that will not be used
when the system configures multipath devices. Devices that are blacklisted will not be grouped into a
multipath device.

By default, all devices are blacklisted, since the following lines appear in the initial configuration file.

blacklist {
devnode "*"
}

To enable multipathing on all of the devices that are supported by default, comment out those lines, as
described in Section 3.1, “Setting Up DM-Multipath”.

After commenting out the universal blacklist, you can specify general device types and individual
devices to blacklist. You can blacklist devices according to the following criteria:

• By WWID, as described in Section 4.2.1, “Blacklisting by WWID”

• By device name, as described in Section 4.2.2, “Blacklisting By Device Name”

• By device type, as described in Section 4.2.3, “Blacklisting By Device Type”

By default, a variety of device types are blacklisted, even after you comment out the initial blacklist
section of the configuration file. For information, see Section 4.2.2, “Blacklisting By Device Name”.

4.2.1. Blacklisting by WWID

You can specify individual devices to blacklist by their World-Wide IDentification with a wwid entry in
the blacklist section of the configuration file.

The following example shows the lines in the configuration file that would blacklist a device with a
WWID of 26353900f02796769.

blacklist {
wwid 26353900f02796769
}

4.2.2. Blacklisting By Device Name

You can blacklist device types by device name so that they will not be grouped into a multipath device
by specifying a devnode entry in the blacklist section of the configuraion file.

12
 Blacklisting By Device Type

The following example shows the lines in the configuration file that would blacklist all SCSI devices,
since it blacklists are sd* devices.

blacklist {
devnode "^sd[a-z]"
}

You can use a devnode entry in the blacklist section of the configuraion file to specify individual
devices to blacklist rather than all devices of specific type; this is not recommended, however. Unless
it is statically mapped by udev rules, there is no guarantee that a specific device will have the same
name on reboot. For example, a device name could change from /dev/sda to /dev/sdb on reboot.

By default, the following devnode entries are compiled in the default blacklist; the devices that these
entires blacklist do not generally support DM-Multipath. To enable multipathing on any of these
devices, you would need to specify them in the blacklist_exceptions section of the configuration
file, as described in Section 4.2.4, “Blacklist Exceptions”.

blacklist {
devnode "^(ram|raw|loop|fd|md|dm-|sr|scd|st)[0-9]*"
devnode "^hd[a-z]"
}

4.2.3. Blacklisting By Device Type

You can specify specific device types in the blacklist section of the configuration file with a device
section. The following example blacklists all IBM DS4200 device and all HP devices.

blacklist {
device {
vendor "IBM"
product "3S42" #DS4200 Product 10
}
device {
vendor "HP"
product "*"
}
}

4.2.4. Blacklist Exceptions

You can use the blacklist_exceptions section of the configuration file to enable multipathing on
devices that have been blacklisted by default. For example, by default, devices with vendor = "IBM"
and product = "S/390.*" are blacklisted since usually DASD devices are used for local storage. If you
do need to enable multipathing on these devices, uncomment the following lines in the configuration
file:

13
Chapter 4. The DM-Multipath Configuration File

blacklist_exceptions {
device {
vendor "IBM"
product "S/390.*"
}
}

When specifying devices in the blacklist_exceptions section of the configuration file, you must
specify the exceptions in the same way they were specified in the blacklist. For example, a WWID
exception will not apply to devices specified by a devnode blacklist entry, even if the blacklisted
device is associated with that WWID. Similarly, devnode exceptions apply only to devnode entries,
and device exceptions apply only to device entries.

4.3. Configuration File Defaults

The /etc/multipath.conf configuration file includes a defaults section that sets the
user_friendly_names parameter to yes, as follows.

defaults {
user_friendly_names yes
}

This overwrites the default value of the user_friendly_names parameter.

The configuration file includes a template of configuration defaults. This section is commented out, as
follows.

#defaults {
# udev_dir /dev
# polling_interval 10
# selector "round-robin 0"
# path_grouping_policy multibus
# getuid_callout "/sbin/scsi_id -g -u -s /block/%n"
# prio_callout /bin/true
# path_checker readsector0
# rr_min_io 100
# max_fds 8192
# rr_weight priorities
# failback immediate
# no_path_retry fail
# user_friendly_names yes
#}

To overwrite the default value for any of the configuration parameters, you can copy the relevant
line from this template into the defaults section and uncomment it. For example, to overwrite
the path_grouping_policy parameter so that it is multibus rather than the default value
of failover, copy the appropriate line from the template to the initial defaults section of the
configuration file, and uncomment it, as follows.

14
 Configuration File Defaults

defaults {
user_friendly_names yes
path_grouping_policy multibus
}

Table 4.1, “Multipath Configuration Defaults” describes the attributes that are set in the defaults
section of the multipath.conf configuration file. These values are used by DM-Multipath unless
they are overwritten by the attributes specified in the devices and multipaths sections of the
multipath.conf file.

Attribute Description
udev_dir Specifies the directory where udev device nodes are created. The
default value is /udev.
polling_interval Specifies the interval between two path checks in seconds. The
default value is 5.
selector Specifies the default algorithm to use in determining what path to
use for the next I/O operation. The default value is round-robin
0.
path_grouping_policy Specifies the default path grouping policy to apply to unspecified
multipaths. Possible values include:
failover = 1 path per priority group
multibus = all valid paths in 1 priority group
group_by_serial = 1 priority group per detected serial number
group_by_prio = 1 priority group per path priority value
group_by_node_name = 1 priority group per target node name
The default value is failover.
getuid_callout Specifies the default program and arguments to call out to obtain a
unique path identifier. An absolute path is required.
The default value is /sbin/scsi_id -g -u -s.
prio_callout Specifies the the default program and arguments to call out to
obtain a path priority value. For example, the ALUA bits in SPC-3
provide an exploitable prio value for example. "none" is a valid
value. The default value is no callout, indicating all paths are equal
path_checker Specifies the default method used to determine the state
of the paths. Possible values include: readsector0, tur,
emc_clariion, hp_sw, and directio. The default value is
readsector0.
rr_min_io Specifies the number of I/O requests to route to a path before
switching to the next path in the current path group. The default
value is 1000.
max_fds (RHEL 5.2 and later) Sets the maximum number of open file
descriptors for the multipathd process. In RHEL 5.3, this
option allows a value of max, which sets the number of open file
descriptors to the system maximum.
rr_weight If set to priorities, then instead of sending rr_min_io
requests to a path before calling selector to choose the

15
Chapter 4. The DM-Multipath Configuration File

Attribute Description
next path, the number of requests to send is determined by
rr_min_io times the path's priority, as determined by the
prio_callout program. Currently, there are priority callouts only
for devices that use the group_by_prio path grouping policy,
which means that all the paths in a path group will always have the
same priority.
If set to uniform, all path weights are equal. The default value is
uniform.
failback Specifies path group failback.
A value of 0 or immediate specifies that as soon as there is a
path group with a higher priority than the current path group the
system switches to that path group.
A numeric value greater than zero specifies deferred failback,
expressed in seconds.
A value of manual specifies that failback can happen only with
operator intervention.
The default value is manual.
no_path_retry A numeric value for this attribute specifies the number of times
the system should attempt to use a failed path before disabling
queueing.
A value of fail indicates immediate failure, without queuing.
A value of queue indicates that queuing should not stop until the
path is fixed.
The default value is (null).
flush_on_last_del (RHEL 5.3 and later) If set to yes, the multipathd daemon will
disable queueing when the last path to a device has been deleted.
The default value is no.
queue_without_daemon (RHEL 5.3 and later) If set to no, the multipathd daemon will
disable queueing for all devices when it is shut down. The default
value is yes.
user_friendly_names If set to yes, specifies that the system should using the bindings
file to assign a persistent and unique alias to the multipath, in
the form of mpathn. The default location of the bindings file is
/var/lib/multipath/bindings, but this can be changed
with the bindings_file option. If set to no, specifies that the
system should use use the WWID as the alias for the multipath. In
either case, what is specified here will be overriden by any device-
specific aliases you specify in the multipaths section of the
configuration file. The default value is no.
bindings_file (RHEL 5.2 and later) The location of the bindings file that is
used with the user_friend_names option. The default value is /
var/lib/multipath/bindings.
mode (RHEL 5.3 and later) The mode to use for the multipath device
nodes, in octal. The default value is determined by the process.
uid (RHEL 5.3 and later) The user ID to use for the multipath device
nodes. You must use the numeric user ID. The default value is
determined by the process.

16
 Multipaths Device Configuration Attributes

Attribute Description
gid (RHEL 5.3 and later) The group ID to use for the multipath device
nodes. You must use the numeric group ID. The default value is
determined by the process.
Table 4.1. Multipath Configuration Defaults

4.4. Multipaths Device Configuration Attributes

Table 4.2, “Multipath Attributes” shows the attributes that you can set in the multipaths section of
the multipath.conf configuration file for each specific multipath device. These attributes apply only
to the one specified multipath. These defaults are used by DM-Multipath and override attributes set in
the defaults and devices sections of the multipath.conf file.

Attribute Description
wwid Specifies the WWID of the multipath device to which the
multipath attributes apply.
alias Specifies the symbolic name for the multipath device to which the
multipath attributes apply.
path_grouping_policy Specifies the default path grouping policy to apply to unspecified
multipaths. Possible values include:
failover = 1 path per priority group
multibus = all valid paths in 1 priority group
group_by_serial = 1 priority group per detected serial number
group_by_prio = 1 priority group per path priority value
group_by_node_name = 1 priority group per target node name
path_selector Specifies the default algorithm to use in determining what path to
use for the next I/O operation.
failback Specifies path group failback.
A value of 0 or immediate specifies that as soon as there is a
path group with a higher priority than the current path group the
system switches to that path group.
A numeric value greater than zero specifies deferred failback,
expressed in seconds.
A value of manual specifies that failback can happen only with
operator intervention.
rr_weight If set to priorities, then instead of sending rr_min_io
requests to a path before calling selector to choose the
next path, the number of requests to send is determined by
rr_min_io times the path's priority, as determined by the
prio_callout program. Currently, there are priority callouts only
for devices that use the group_by_prio path grouping policy,
which means that all the paths in a path group will always have the
same priority.
If set to uniform, all path weights are equal.
no_path_retry A numeric value for this attribute specifies the number of times
the system should attempt to use a failed path before disabling
queueing.
A value of fail indicates immediate failure, without queueing.

17
Chapter 4. The DM-Multipath Configuration File

Attribute Description
A value of queue indicates that queuing should not stop until the
path is fixed.
flush_on_last_del (RHEL 5.3 and later) If set to yes, the multipathd daemon will
disable queueing when the last path to a device has been deleted.
The default value is no.
rr_min_io Specifies the number of I/O requests to route to a path before
switching to the next path in the current path group.
mode (RHEL 5.3 and later) The mode to use for the multipath device
nodes, in octal. The default value is determined by the process.
uid (RHEL 5.3 and later) The user ID to use for the multipath device
nodes. You must use the numeric user ID. The default value is
determined by the process.
gid (RHEL 5.3 and later) The group ID to use for the multipath device
nodes. You must use the numeric group ID. The default value is
determined by the process.
Table 4.2. Multipath Attributes

The following example shows multipath attributes specified in the configuration file for two specific
multipath devices. The first device has a WWID of 3600508b4000156d70001200000b0000 and a
symbolic name of yellow.

The second multipath device in the example has a WWID of 1DEC_____321816758474 and a
symbolic name of red. In this example, the rr_weight attributes is set to priorities.

multipaths {
multipath {
wwid 3600508b4000156d70001200000b0000
alias yellow
path_grouping_policy multibus
path_checker readsector0
path_selector "round-robin 0"
failback manual
rr_weight priorities
no_path_retry 5
}
multipath {
wwid 1DEC_____321816758474
alias red
rr_weight priorities
}
}

4.5. Configuration File Devices

Table 4.3, “Device Attributes” shows the attributes that you can set for each individual storage device
in the devices section of the multipath.conf configuration file. These attributes are used by DM-
Multipath unless they are overwritten by the attributes specified in the multipaths section of the

18
 Configuration File Devices

multipath.conf file for paths that contain the device. These attributes override the attributes set in
the defaults section of the multipath.conf file.

Many devices that support multipathing are included by default in a multipath configuration. The values
for the devices that are supported by default are listed in the multipath.conf.defaults file.
You probably will not need to modify the values for these devices, but if you do you can overwrite the
default values by including an entry in the the configuration file for the device that overwrites those
values. You can copy the device configuration defaults from the multipath.conf.defaults file for
the device and override the values that you want to change.

To add a device to this section of the configuration file that is not configured automatically by default,
you need to set the vendor and product parameters. You can find these values by looking at /sys/
block/device_name/device/vendor and /sys/block/device_name/device/model where
device_name is the device to be multipathed, as in the following example:

[root@cypher-06 ~]# cat /sys/block/sda/device/vendor

WINSYS
[root@cypher-06 ~]# cat /sys/block/sda/device/model
SF2372

The additional parameters to specify depend on your specific device. If the device is active/active, you
will usually not need to set additional parameters. You may want to set path_grouping_policy
to multibus. Other parameters you may need to set are no_path_retry and rr_min_io, as
described in Table 4.3, “Device Attributes”.

If the device is active/passive, but it automatically switches paths with I/O to the passive path,
you need to change the checker function to one that does not send IO/ to the path to test if it is
working (otherwise, your device will keep failing over). This almost always means that you set the
path_checker to tur; this works for all SCSI devices that support the Test Unit Ready command,
which most do.

If the device needs a special command to switch paths, then configuring this device for multipath
requires a hardware handler kernel module. The current hardware handlers are emc and "rdac. If
these are not sufficient for your device, you may not be able to configure the device for multipath.

Attribute Description
vendor Specifies the vendor name of the storage device to which the
device attributes apply, for example COMPAQ.
product Specifies the product name of the storage device to which the
device attributes apply, for example HSV110 (C)COMPAQ.
path_grouping_policy Specifies the default path grouping policy to apply to unspecified
multipaths. Possible values include:
failover = 1 path per priority group
multibus = all valid paths in 1 priority group
group_by_serial = 1 priority group per detected serial number
group_by_prio = 1 priority group per path priority value
group_by_node_name = 1 priority group per target node name
getuid_callout Specifies the default program and arguments to call out to obtain a
unique path identifier. An absolute path is required.

19
Chapter 4. The DM-Multipath Configuration File

Attribute Description
prio_callout Specifies the the default program and arguments to call out to
obtain a path weight. Weights are summed for each path group to
determine the next path group to use in case of failue. "none" is a
valid value.
path_checker Specifies the default method used to determine the state of
the paths. Possible values include readsector0 and tur,
emc_clariion, hp_sw, and directio.
path_selector Specifies the default algorithm to use in determining what path to
use for the next I/O operation.
features The extra features of multipath devices. The only existing
feature is queue_if_no_path, which is the same as setting
no_path_retry to queue. For information on issues that may
arise when using this feature, see Section 5.4, “Issues with
queue_if_no_path feature”.
hardware_handler Specifies a module that will be used to perform hardware specific
actions when switching path groups or handling I/O errors.
Possible values include 0, 1 emc, and 1 rdac. The default value
is 0.
rr_weight If set to priorities, then instead of sending rr_min_io
requests to a path before calling selector to choose the
next path, the number of requests to send is determined by
rr_min_io times the path's priority, as determined by the
prio_callout program. Currently, there are priority callouts only
for devices that use the group_by_prio path grouping policy,
which means that all the paths in a path group will always have the
same priority.
If set to uniform, all path weights are equal. The default value is
uniform.
no_path_retry A numeric value for this attribute specifies the number of times
the system should attempt to use a failed path before disabling
queueing.
A value of fail indicates immediate failure, without queuing.
A value of queue indicates that queuing should not stop until the
path is fixed.
The default value is (null).
failback Specifies path group failback.
A value of 0 or immediate specifies that as soon as there is a
path group with a higher priority than the current path group the
system switches to that path group.
A numeric value greater than zero specifies deferred failback,
expressed in seconds.
A value of manual specifies that failback can happen only with
operator intervention.
rr_min_io Specifies the number of I/O requests to route to a path before
switching to the next path in the current path group. The default
value is 1000.

20
 Configuration File Devices

Attribute Description
flush_on_last_del (RHEL 5.3 and later) If set to yes, the multipathd daemon will
disable queueing when the last path to a device has been deleted.
The default value is no.
product_blacklist Specifies a regular expression used to blacklist devices by
product.
Table 4.3. Device Attributes

The following example shows a device entry in the multipath configuration file.

# }
# device {
# vendor "COMPAQ "
# product "MSA1000 "
# path_grouping_policy multibus
# path_checker tur
# rr_weight priorities
# }
#}

21
22
Chapter 5.

DM-Multipath Administration and

Troubleshooting
This chapter will provide information on administering DM-Multipath on a running system. It includes
sections on the following topics:

• Resizing an Online Multipath Device

• The Multipath Daemon

• Issues with Large Number of LUNs

• Issues with queue_if_no_path feature

• Multipath Command Output

• Multipath Queries with multipath Command

• Multipath Command Options

• Multipath Queries with dmsetup Command

• Troubleshooting with the multipathd Interactive Console

5.1. Resizing an Online Multipath Device

If you need to resize an online multipath device, use the following procedure.

1. Resize your physical device.

2. Use the following command to find the paths to the LUN:

# multipath -l

3. Resize your paths. For SCSI devices, writing a 1 to the rescan file for the device causes the
SCSI driver to rescan, as in the following command:

# echo 1 > /sys/block/device_name/device/rescan

4. Resize your multipath device by running the multipathd resize command:

# multipathd -k'resize map mpath0'

5. Resize the filesystem (assuming no LVM or DOS partitions are used):

# resize2fs /dev/mapper/mpath0

23
Chapter 5. DM-Multipath Administration and Troubleshooting

For further information on resizing an online LUN, see the Online Storage Reconfiguration Guide.

5.2. The Multipath Daemon

If you find you have trouble implementing a multipath configuration, you should ensure that the
multipath daemon is running, as described in Chapter 3, Setting Up DM-Multipath. The multipathd
daemon must be running in order to use multipathed devices.

5.3. Issues with Large Number of LUNs

When a large number of LUNs are added to a node, using multipathed devices can significantly
increase the time it takes for the udev device manager to create device nodes for them. If
you experience this problem, you can correct it by deleting the following line in /etc/udev/
rules.d/40-multipath.rules:

KERNEL!="dm-[0-9]*", ACTION=="add", PROGRAM=="/bin/bash -c '/sbin/lsmod | /

bin/grep ^dm_multipath'", RUN+="/sbin/multipath -v0 %M:%m"

This line causes the udev device manager to run multipath every time a block device is added
to the node. Even with this line removed, the multipathd daemon will still automatically create
multipathed devices, and multipath will still be called during the boot process for nodes with
multipathed root file systems. The only change is that multipathed devices will not be automatically
created when the multipathd daemon is not running, which should not be a problem for the vast
majority of multipath users.

5.4. Issues with queue_if_no_path feature

If features "1 queue_if_no_path" is specified in the /etc/multipath.conf file, then
any process that issues I/O will hang until one or more paths are restored. To avoid this, set the
no_path_retry N parameter in the /etc/multipath.conf file (where N is the number of times
the system should retry a path).

When you set the no_path_retry parameter, remove the features "1 queue_if_no_path"
option from the /etc/multipath.conf file as well. If, however, you are using a multipathed device
for which the features "1 queue_if_no_path" option is set as a compiled-in default, as it is for
many SAN devices, you must explicitly add features "0" to override this default. You can do this
by copying the existing devices section for your device from /usr/share/doc/device-mapper-
multipath-0.4.7/multipath.conf.defaults into /etc/multipath.conf and editing it to
suit your needs.

If you need to use the features "1 queue_if_no_path" option and you experience the issue
noted here, use the dmsetup command to edit the policy at runtime for a particular LUN (that is, for
which all the paths are unavailable). For example, if you want to change the policy on the multipath
device mpath2 from "queue_if_no_path" to "fail_if_no_path", execute the following
command.

dmsetup message mpath2 0 "fail_if_no_path"

Note that you must specify the mpathn alias rather than the path.

24
 Multipath Command Output

5.5. Multipath Command Output

When you create, modify, or list a multipath device, you get a printout of the current device setup. The
format is as follows.

For each multipath device:

action_if_any: alias (wwid_if_different_from_alias) [size][features]

[hardware_handler]

For each path group:

\_ scheduling_policy [path_group_priority_if_known]
[path_group_status_if_known]

For each path:

\_ host:channel:id:lun devnode major:minor [path_status]

[dm_status_if_known]

For example, the output of a multipath command might appear as follows:

mpath1 (3600d0230003228bc000339414edb8101) [size=10 GB][features="0"]

[hwhandler="0"]
\_ round-robin 0 [prio=1][active]
\_ 2:0:0:6 sdb 8:16 [active][ready]
\_ round-robin 0 [prio=1][enabled]
\_ 3:0:0:6 sdc 8:64 [active][ready]

If the path is up and ready for I/O, the status of the path is ready or active. If the path is down, the
status is faulty or failed. The path status is updated periodically by the multipathd daemon
based on the polling interval defined in the /etc/multipath.conf file.

The dm status is similar to the path status, but from the kernel's point of view. The dm status has
two states: failed, which is analogous to faulty, and active which covers all other path states.
Occasionally, the path state and the dm state of a device will temporarily not agree.

Note
When a multipath device is being created or modified, the path group status and the dm
status are not known. Also, the features are not always correct. When a multipath device
is being listed, the path group priority is not known.

5.6. Multipath Queries with multipath Command

You can use the -l and -ll options of the multipath command to display the current multipath
configuration. The -l option displays multipath topology gathered from information in sysfs and

25
Chapter 5. DM-Multipath Administration and Troubleshooting

the device mapper. The -ll option displays the information the -l displays in addition to all other
available components of the system.

When displaying the multipath configuration, there are three verbosity levels you can specify with the
-v option of the multipath command. Specifying -v0 yields no output. Specifying -v1 outputs the
created or updated multipath names only, which you can then feed to other tools such as kpartx.
Specifying -v2 prints all detected paths, multipaths, and device maps.

The following example shows the output of a multipath -l command.

# multipath -1
mpath1 (3600d0230003228bc000339414edb8101)
[size=10 GB][features="0"][hwhandler="0"]
\_ round-robin 0 [prio=1][active]
\_ 2:0:0:6 sdb 8:16 [active][ready]
\_ round-robin 0 [prio=1][enabled]
\_ 3:0:0:6 sdc 8:64 [active][ready]

5.7. Multipath Command Options

Table 5.1, “Useful multipath Command Options” describes some options of the multipath
command that you may find useful.

Option Description
-l Display the current multipath configuration gathered from sysfs and
the device mapper.
-ll Display the current multipath configuration gathered from sysfs, the
device mapper, and all other available components on the system.
-f device Remove the named multipath device.
-F Remove all multipath devices.
Table 5.1. Useful multipath Command Options

5.8. Determining Device Mapper Entries with the dmsetup

Command
You can use the dmsetup command to find out which device mapper entries match the multipathed
devices.

The following command displays all the device mapper devices and their major and minor numbers.
The minor numbers determine the name of the dm device. For example, a minor number of 3
corresponds to the multipathed device /dev/dm-3.

# dmsetup ls
mpath2 (253, 4)
mpath4p1 (253, 12)
mpath5p1 (253, 11)
mpath1 (253, 3)

26
 Troubleshooting with the multipathd Interactive Console

mpath6p1 (253, 14)

mpath7p1 (253, 13)
mpath0 (253, 2)
mpath7 (253, 9)
mpath6 (253, 8)
VolGroup00-LogVol01 (253, 1)
mpath5 (253, 7)
VolGroup00-LogVol00 (253, 0)
mpath4 (253, 6)
mpath1p1 (253, 10)
mpath3 (253, 5)

5.9. Troubleshooting with the multipathd Interactive

Console
The multipathd -k command is an interactive interface to the multipathd daemon. Entering
this command brings up an interactive multipath console. After entering this command, you can enter
help to get a list of available commands, you can enter a interactive command, or you can enter
CTRL-D to quit.

The multipathd interactive console can be used to troubleshoot problems you may be having with
your system. For example, the following command sequence displays the multipath configuration,
including the defaults, before exiting the console.

# multipathd -k
> > show config
> > CTRL-D

The following command sequence ensures that multipath has picked up any changes to the
multipath.conf,

# multipathd -k
> > reconfigure
> > CTRL-D

Use the following command sequence to ensure that the path checker is working properly.

# multipathd -k
> > show paths
> > CTRL-D

27
28
Appendix A. Revision History
Revision 5.4-1 Tue Aug 18 2009 Steven Levine [email protected]
Resolves: #466970
Adds note clarifying that if a multipathed device contains partitions, you cannot create a logical
volume using the whole device without removing the partitions.

Resolves #513330
Elaborates documentation to address issues with queue_if_no_path features option.

Resolves #510707
Adds a procedure for resizing online multipath devices.

Resolves #498986
Fixes minor typo.

Resolves #498988
Fixes minor typo.

Revision 1.0 Thu Jan 29 2009

29
30
Index
product_blacklist parameter, 19
queue_without_daemon parameter, 15
rr_min_io parameter, 15, 17
rr_weight parameter, 15, 17, 19
Symbols selector parameter, 15
/etc/multipath.conf package, 7 udev_dir parameter, 15
uid parameter, 15, 17
A user_friendly_names parameter, 14, 15
active/active configuration vendor parameter, 19
definition, 1 wwid parameter, 17
illustration, 2 configuring
active/passive configuration DM-Multipath, 7
definition, 1
illustration, 1 D
alias parameter , 17 defaults section
configuration file, 5 multipath.conf file, 14
dev/mapper directory, 5
B dev/mpath directory, 5
bindings_file parameter, 15 device name, 5
blacklist device-mapper-multipath package, 7
configuration file, 12 devices
default devices, 13 adding, 10, 18
device name, 12 devices section
device type, 13 multipath.conf file, 18
in configuration file, 7 DM-Multipath
WWID, 12 and LVM, 6, 6
blacklist_exceptions section components, 3
multipath.conf file, 13 configuration file, 11
configuring, 7
C definition, 1
device name, 5
chkconfig command, 8
devices, 5
configuration file
failover, 1
alias parameter, 17
overview, 1
bindings_file parameter, 15
redundancy, 1
blacklist, 7, 12
setup, 7
failback parameter, 15, 17, 19
setup, overview, 4
features parameter, 19
dm-multipath kernel module , 3
flush_on_last_del parameter, 15, 17, 19
dm-n devices, 5
getuid_callout parameter, 15, 19
dmsetup command, determining device mapper
gid parameter, 15, 17
entries, 26
hardware_handler parameter, 19
max_fds parameter, 15
mode parameter, 15, 17 F
no_path_retry parameter, 15, 17, 19 failback parameter, 15, 17, 19
overview, 11 failover, 1
path_checker parameter, 15, 19 features parameter, 19
path_grouping_policy parameter, 15, 17, 19 feedback, vi, vi
path_selector parameter, 17, 19 flush_on_last_del parameter, 15, 17, 19
polling-interval parameter, 15
prio_callout parameter, 15, 19 G
product parameter, 19 getuid_callout parameter, 15, 19

31
Index

gid parameter, 15, 17 product parameter, 19

product_blacklist parameter, 19
H
hardware_handler parameter, 19 Q
queue_without_daemon parameter, 15
K
kpartx command , 3 R
resizing a multipath device, 23
L rr_min_io parameter, 15, 17
local disks, ignoring, 8 rr_weight parameter, 15, 17, 19
LVM physical volumes
multipath devices, 6 S
lvm.conf file , 6 selector parameter, 15
setup
M DM-Multipath, 7
max_fds parameter, 15 storage array support, 3
mode parameter, 15, 17 storage arrays
modprobe command, 7 adding, 10, 18
multipath command , 3, 7
options, 26 U
output, 25 udev_dir parameter, 15
queries, 25 uid parameter, 15, 17
multipath daemon (multipathd), 24 user_friendly_names parameter , 5, 14, 15
multipath devices, 5
logical volumes, 6
LVM physical volumes, 6
V
multipath.conf file, 3, 11 vendor parameter, 19
blacklist_exceptions section, 13
defaults section, 14 W
devices section, 18 World Wide Identifier (WWID), 5
multipaths section, 17 wwid parameter, 17
multipath.conf.annotated file, 11
multipath.conf.defaults file, 3, 11
multipathd
command, 27
interactive console, 27
multipathd daemon , 3
multipathd start command, 7
multipaths section
multipath.conf file, 17

N
no_path_retry parameter, 15, 17, 19

P
path_checker parameter, 15, 19
path_grouping_policy parameter, 15, 17, 19
path_selector parameter, 17, 19
polling_interval parameter, 15
prio_callout parameter, 15, 19

32