Scribd
Upload
122 views

Accelerator Control System

This document provides instructions for removal, installation, and inspection of an accelerator control system. It includes an exploded view diagram labeling the main components. The removal process involves disconnecting the accelerator pedal position sensor harness connector and loosening mounting bolts to remove the accelerator pedal assembly. Installation is the reverse of removal, making sure to insert the locating pin and hook properly. Inspection after installation includes checking pedal movement and fully released position, as well as electrical inspection of the position sensor.

Uploaded by

Napi
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
122 views

Accelerator Control System

This document provides instructions for removal, installation, and inspection of an accelerator control system. It includes an exploded view diagram labeling the main components. The removal process involves disconnecting the accelerator pedal position sensor harness connector and loosening mounting bolts to remove the accelerator pedal assembly. Installation is the reverse of removal, making sure to insert the locating pin and hook properly. Inspection after installation includes checking pedal movement and fully released position, as well as electrical inspection of the position sensor.

Uploaded by

Napi
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

ENGINE

ACCELERATOR CONTROL SYSTEM


SECTION ACC ACC

E
CONTENTS
PRECAUTION ............................................... 2 ACCELERATOR CONTROL SYSTEM .............. 3 F
Exploded View .......................................................... 3
PRECAUTIONS ................................................... 2 Removal and Installation .......................................... 3
Precautions for Removing Battery Terminal ............. 2 Inspection ................................................................. 3 G
REMOVAL AND INSTALLATION ................ 3
H

Revision: 2014 April ACC-1 AD0


PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precautions for Removing Battery Terminal INFOID:0000000010041534

• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
SEF289H
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.

Revision: 2014 April ACC-2 AD0


ACCELERATOR CONTROL SYSTEM
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION A
ACCELERATOR CONTROL SYSTEM
Exploded View INFOID:0000000010041535
ACC

JPBIA3364GB
H
Accelerator pedal assembly Brake pedal bracket
Locating hook Locating pin
I
: N·m (kg-m, in-lb)

Removal and Installation INFOID:0000000010041536


J

REMOVAL
1. Disconnect accelerator pedal position sensor harness connector. K
2. Loosen mounting bolts, and remove accelerator pedal assembly.
CAUTION:
• Never disassemble accelerator pedal assembly. Never remove accelerator pedal position sensor
L
from accelerator pedal assembly.
• Avoid impact from dropping etc. during handling.
• Be careful to keep accelerator pedal assembly away from water.
M
INSTALLATION
Note the following, and install in the reverse order of removal.
• Insert the locating pin while inserting the locating hook in to the break pedal bracket. Tighten mounting bolts
to accelerator pedal assembly. N
CAUTION:
• Never squeeze the locating hook into the break pedal bracket when inserting the locating pin into
the hole on the brake pedal bracket side. O
• When harness connector of accelerator pedal position sensor is disconnected, perform “Accelerator
Pedal Released Position Learning”. Refer to HR12DE EC-93, "Work Procedure".
Inspection INFOID:0000000010041537 P

INSPECTION AFTER INSTALLATION


• Check accelerator pedal moves smoothly within the whole operation range when it is fully depressed and
released.
• Check accelerator pedal securely returns to the fully released position.
• For the electrical inspection of accelerator pedal position sensor. Refer to EC-222, "Component Inspection",
EC-225, "Component Inspection" and EC-231, "Component Inspection".

Revision: 2014 April ACC-3 AD0

You might also like