Scribd
Upload
58 views

Manufacturer: National Instruments Board Assembly Part Numbers

This document provides information about volatile and non-volatile memory on National Instruments USB-232/x and USB-485/x devices. It lists the available board assembly part numbers and describes any configuration data stored in EEPROM memory. No volatile memory is present on the devices. Procedures for identifying the board assembly part number and definitions of terms like volatile memory and clearing are also included.

Uploaded by

paulpuscasu
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
58 views

Manufacturer: National Instruments Board Assembly Part Numbers

This document provides information about volatile and non-volatile memory on National Instruments USB-232/x and USB-485/x devices. It lists the available board assembly part numbers and describes any configuration data stored in EEPROM memory. No volatile memory is present on the devices. Procedures for identifying the board assembly part number and definitions of terms like volatile memory and clearing are also included.

Uploaded by

paulpuscasu
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Letter of Volatility

USB-232/x, USB-485/x

Manufacturer: National Instruments

Board Assembly Part Numbers (Refer to Procedure 1 for identification procedure):


Part Number and Revision Description
187660A-01(L) or later USB-SERIAL, RS-232, 2 PORTS
187660A-02(L) or later USB-SERIAL, RS-485, 2 PORTS
187660A-11(L) or later USB-SERIAL, RS-232, 4 PORTS
187660A-12(L) or later USB-SERIAL, RS-485, 4 PORTS

Volatile Memory
Battery User1 System Sanitization
Target Data Type Size Backup Accessible Accessible Procedure
None

Non-Volatile Memory (incl. Media Storage)


Battery User System Sanitization
Target Data Type Size Backup Accessible Accessible Procedure
Device configuration EEPROM 2 kB No No Yes None

Device configuration EEPROM 2 KB No No Yes None


(4 Ports Devices Only)

1
Refer to Terms and Definitions section for clarification of User and System Accessible

August 2017 Notice: This document is subject to change without notice. Contact: 866-275-6964
377312A-01 Rev 001 For the most recent version, visit ni.com/manuals. [email protected]
Letter of Volatility
USB-232/x, USB-485/x

Procedures

Procedure 1 – Board Assembly Part Number identification:


To determine the Board Assembly Part Number and Revision, refer to the “P/N” label applied to the surface of your
product as shown below. The Assembly Part Number should be formatted as “P/N: ######a-vvL” where “a” is the
letter revision of the Board Assembly (eg. A, B, C…) and the “vv” is the type identifier. If the product is RoHS
compliant, “L” can be found at the end of the part number.

Bottom view:

August 2017 Notice: This document is subject to change without notice. Contact: 866-275-6964
377312A-01 Rev 001 For the most recent version, visit ni.com/manuals. [email protected]
Letter of Volatility
USB-232/x, USB-485/x

Terms and Definitions

Cycle Power:
The process of completely removing power from the device and its components and allowing for adequate
discharge. This process includes a complete shutdown of the PC and/or chassis containing the device; a reboot is
not sufficient for the completion of this process.

Volatile Memory:
Requires power to maintain the stored information. When power is removed from this memory, its contents are lost.
This type of memory typically contains application specific data such as capture waveforms.

Non-Volatile Memory:
Power is not required to maintain the stored information. Device retains its contents when power is removed.
This type of memory typically contains information necessary to boot, configure, or calibrate the product or may
include device power up states.

User Accessible:
The component is read and/or write addressable such that a user can store arbitrary information to the component
from the host using a publicly distributed NI tool, such as a Driver API, the System Configuration API, or MAX.

System Accessible:
The component is read and/or write addressable from the host without the need to physically alter the product.

Clearing:
Per NIST Special Publication 800-88 Revision 1, “clearing” is a logical technique to sanitize data in all User
Accessible storage locations for protection against simple non-invasive data recovery techniques using the same
interface available to the user; typically applied through the standard read and write commands to the storage
device.

Sanitization:
Per NIST Special Publication 800-88 Revision 1, “sanitization” is a process to render access to “Target Data” on the
media infeasible for a given level of effort. In this document, clearing is the degree of sanitization described.

August 2017 Notice: This document is subject to change without notice. Contact: 866-275-6964
377312A-01 Rev 001 For the most recent version, visit ni.com/manuals. [email protected]

You might also like