TESTING

4,000 V BREAKDOWN
VOLTAGE DS RELAYS
DS-BT
RELAYS
FEATURES
20.65 10.65 •4,000 V breakdown voltage
.813 .419
•Reinforced insulation between coil and contacts
10.5
.413 •Surge voltage withstand: 1500 V FCC Parts 68

mm inch

SPECIFICATIONS
Contact Characteristics
Arrangement 2 Form C 2 Form D Arrangement 2 Form C 2 Form D
Initial contact resistance, max. Max. operating speed 60 cpm at rated load
50 mΩ
(By voltage drop 6 V DC 1 A) Initial insulation resistance*1 Min. 100 MΩ (at 500 V DC)
Contact material Gold-clad silver 750 Vrms 500 Vrms
Initial Between open contacts
Nominal switching capacity 2 A 30 V DC 1 A 30 V DC break- for 1 min. for 1 min.
Rating Max. switching power 60 W, 125 VA 30 W, 62.5 VA down Between contacts and coil 4,000 Vrms for 1 min.
(resistive Max. switching voltage 220 V DC, 250 V AC voltage*2 Between contacts sets 750 V 500 V
load) Max. switching current 2A 1A FCC surge voltage between open
1,500 V
Min. switching capacity**1 10 µA 10 mV DC contacts
Electrical Mechanical (at 180 cpm) 2×107 106 Operate time*3 (at nominal volt-
Approx. 3 ms
life (min. age)
ope.) Electrical (at 20 cpm) 2×105 Release time (without diode)*3
Approx. 2 ms
**1 This value can change due to the switching frequency, environmental (at nominal voltage)
conditions, and desired reliability level, therefore it is recommended to Temperature rise Max. 65°C
check this with the actual load. 10 to 55 Hz
Functional*4
Coil Vibration at double amplitude of 3.3 mm
resistance 10 to 55 Hz
Arrangement 2 Form C 2 Form D Destruction*5
at double amplitude of 5 mm
Nominal operating power 360 mW 540 mW
Shock Functional*6 Min. 294 m/s2 (30 G)
Remarks resistance Destruction Min. 980 m/s2 (100 G)
* Specifications will vary with foreign standards certification ratings.
*1 Measurement at same location as "Initial breakdown voltage" section Conditions for oper- Ambient –40°C to +70°C –40°C to +60°C
*2 Detection current: 10mA ation, transport and temp. –40°F to +158°F –40°F to +140°F
*3 Excluding contact bounce time storage*7
*4 Half-wave pulse of sine wave: 11ms, detection time: 10µs (Not freezing and
*5 Half-wave pulse of sine wave: 6ms condensing at low Humidity 5 to 85%R.H.
*6 Detection time: 10µs
*7 Refer to 5. Conditions for operation, transport and storage mentioned in
temperature)
AMBIENT ENVIRONMENT (Page 61) Unit weight Approx. 4.0 g 0.14 oz

TYPICAL APPLICATIONS ORDERING INFORMATION

Modem
DSBT 2 M 2D DC3V
Facsimile
Telecommunication equipment

Contact Sensitivity MBB function Coil voltage

arrangement
S: 360 mW Nil: BBM (Form C)
2: 2 Form C or (2 Form C only) DC 1.5, 3, 5,
M: 540 mW 2D: 2MBB
2 Form D 6, 9, 12, 24 V
(2 Form D only) (2 Form D)
Note: Standard packing; Carton: 25 pcs. Case 1,000 pcs.

192
 DS-BT
TYPES AND COIL DATA (at 20°C 68°F)
1) 2 Form C type
Pick-up Drop-out Nominal operating Coil Nominal Max. allowable
Operating Coil voltage,
Part No. voltage, voltage, current, resistance, operating voltage, V DC
function V DC
V DC (max.) V DC (min.) mA (±10%) Ω (±10%) power, mW (at 50°C 122°F)
DSBT2-S-DC1.5V 1.5 1.125 0.15 240 6.25 1.95
DSBT2-S-DC3V 3 2.25 0.3 120 25 3.9
DSBT2-S-DC5V 5 3.75 0.5 72 69.4 6.5
Single side
DSBT2-S-DC6V 6 4.5 0.6 60 100 360 7.8
stable
DSBT2-S-DC9V 9 6.75 0.9 40 225 11.7
DSBT2-S-DC12V 12 9 1.2 30 400 15.6
DSBT2-S-DC24V 24 18 2.4 15 1,600 31.2
2) 2 Form D type
Pick-up Drop-out Nominal operating Coil Nominal Max. allowable
Operating Coil voltage,
Part No. voltage, voltage, current, resistance, operating voltage, V DC
function V DC
V DC (max.) V DC (min.) mA (±10%) Ω (±10%) power, mW (at 50°C 122°F)
DSBT2-M-2D-DC1.5V 1.5 1.125 0.15 360 4.2 1.8
DSBT2-M-2D-DC3V 3 2.25 0.3 180 16.7 3.6
DSBT2-M-2D-DC5V 5 3.75 0.5 108 46.3 6
Single side
DSBT2-M-2D-DC6V 6 4.5 0.6 90 66.7 540 7.2
stable
DSBT2-M-2D-DC9V 9 6.75 0.9 60 150 10.8
DSBT2-M-2D-DC12V 12 9 1.2 45 266.7 14.4
DSBT2-M-2D-DC24V 24 18 2.4 22.5 1,066.7 28.8
Note: Standard packing Tube: 25 pcs. Case: 1,000 pcs.

DIMENSIONS mm inch
PC board pattern (Bottom view)
20.65 10.65
.813 .419 8-0.9 dia.
8-.035 dia.

10.50
.413
9.9 7.62 7.82
.390 .300 .308

3.4 5.08 5.08 7.62

.134
0.30 0.6 0.3 0.6 0.35 .200 .200 .300
.012 .024 .012 .024 .014
7.62
.300 5.08
.200
5.08
.200
7.62
.300
2
.079 Tolerance: ±0.1 ± .004
5.6
.220 Schematic (Bottom view)
7.82
.308 9 11 13 16
N.O. N.C. COM –
General tolerance: ±0.3 ± .012

N.O. N.C. COM +

8 6 4 1

REFERENCE DATA
1. Mechanical life test Change of pick-up and drop-out voltage Change of contact resistance
Tested sample: DSBT2-S-DC5V, 10 pcs.
Pick-up/drop-out voltage, V DC

Coil applied voltage: 5 V DC N.C. contact

Operating frequency: 30 cpm N.O. contact
Contact resistance, mΩ

4
Pick-up voltage Max. 100
–
x
Min.
3
Max.
Max.
–
x
–
x
2 Drop-out voltage
Max. Min.
– Min.
x 10
1
Min.

0 0
0 10 100 1000 0 10 100 1000
No. of operations, × 104 No. of operations, × 104

193
DS-BT
2. Electrical life test (resistive)
Tested sample: DSBT2-S-DC12V, 6 pcs.
Condition: 2 A 30 V DC resistive load, 30 cpm 7 100

Pick-up/drop-out voltage, V DC
Pick-up voltage N.C. contact
Circuit Max.

Contact resistance, mΩ
6 – N.O. contact
x
Min.
5
N.O.:
30 V DC No.11–13 Max.
N.C.: 4 –
x
No. 4–6 Max.
–
x
3 Min.
Drop-out voltage 10 Min.
Max.
–
2 x
Min.
1

0 5 10 15 20 0 5 10 15 20
No. of operations, × 104 No. of operations, × 104

3. Coil temperature rise 4. Operate and release time characteristics

Tested sample: DSBT2-S-DC12V, 5 pcs. Tested sample: DSBT2-S-DC5V, 10 pcs.
Measured portion: Inside the coil Ambient temperature: 23°C 73°F Without diode (T1)

80 Coil
Coil temperature rise, °C

70 6
N.O. contact
2A
1A T1: Operate time 5

Operate time, ms
0A T1
60 T2 T2: Operate bounce
Coil time
4
50
3
40 N.C. contact
2
T3: Release time
T3
30 T4 T4: Release bounce
time 1

0 200 400 600 800 0 80 100 120

Coil power, mW Coil applied voltage, %V

Without diode (T2) Without diode (T3) Without diode (T4)

Release bounce time, ms
Operate bounce time, ms

1.5 6 1.5

Measured terminals: 4-6

Release time, ms

5
Measured terminals: 9-13
1.0 4 1.0

2 Measured terminals: 11-13

0.5 0.5
Measured terminals: 4-8
1

0 80 100 120 0 80 100 120 0 80 100 120

Coil applied voltage, %V Coil applied voltage, %V Coil applied voltage, %V

5. Distribution of pick-up and drop-out voltage 6. Distribution of breakdown voltage

Tested sample: DSBT2-S-DC5V, 50 pcs. (between contacts and coil)
Pick-up voltage Drop-out voltage Tested sample: DSBT2-S-DC5V, 100 pcs.

Specified value: Less than 3.75 V DC Specified value: More than 0.50 V DC 40 Mean: AC 5169 V
– 3.22 V DC
Mean value (x): –– 1.65 V DC
Mean value (x): Max.: AC 5800 V
Max.: 3.69 V DC Max.: 2.23 V DC Min.: AC 4700 V
Min.: 2.65 V DC Min.: 0.78 V DC
30
20 20
Quantity
Quantity

Quantity

20

10 10
10

0
2.0 2.5 3.0 3.5 4.0 4.5 5.0 0 0.5 1.0 1.5 2.0 2.5 3.0 AC 4000 AC 5000 AC 6000
Pick-up voltage, V Drop-out voltage, V Breakdown voltage, V AC

For Cautions for Use, see Relay Technical Information

194
9/1/2000 All Rights Reserved, © Copyright Matsushita Electric Works, Ltd.
This datasheet has been downloaded from:

www.DatasheetCatalog.com

Datasheets for electronic components.