Scribd
Upload
331 views

Elevator Guide Rails - Frequently Asked Questions

The document discusses frequently asked questions about elevator guide rails. It addresses questions about the differences between cold-drawn and planed guide rails, why cold-drawn rails cannot be used at speeds over 1.6 m/sec, whether speed limits are precise, the importance of choosing the right clip, why slight jolting may occur, the need to clean tectyl before assembly, whether guide rails wear out, why they are made of steel, why machines are mounted on them, why they are 5 meters long, how building movements affect the riding path, why assembly of the riding path is important, whether they have surface treatments, how the counterweight riding path can influence comfort, how fishplates should be calculated, how

Uploaded by

thanggimme.phan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
331 views

Elevator Guide Rails - Frequently Asked Questions

The document discusses frequently asked questions about elevator guide rails. It addresses questions about the differences between cold-drawn and planed guide rails, why cold-drawn rails cannot be used at speeds over 1.6 m/sec, whether speed limits are precise, the importance of choosing the right clip, why slight jolting may occur, the need to clean tectyl before assembly, whether guide rails wear out, why they are made of steel, why machines are mounted on them, why they are 5 meters long, how building movements affect the riding path, why assembly of the riding path is important, whether they have surface treatments, how the counterweight riding path can influence comfort, how fishplates should be calculated, how

Uploaded by

thanggimme.phan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Elevator guide rails – Frequently Asked Questions

What difference is there between cold-drawn and planed oneelevator guide rails?
The process for cold-drawn involves stretching the material thus modifying its structure.
Planing involves machining the oneelevator guide rail by stripping the edgings.

Why can’t the cold-drawn oneelevator guide rails be used at speeds over 1.6 m/sec?
Because the cold-drawn process produces short bends caused by the variations in the raw
material thickness rolled along the section. These bends make the lateral acceleration rates
high.

Are the speed limits for the different qualities precise?


No, the calculations for comfort are carried out using a mathematical model validated with
practical tests, hence the speed limits set are approximate.

Why is it important to choose the right clip?


The clip must be capable of supporting all the stresses produced when the lift moves and must
also be capable of allowing the oneelevator guide rail to slide if necessary.

Why is slight cyclic jolting felt in some elevators?


Jerking at the joints of oneelevator guide rails that do not have the right quality produces this
jolting movement.

Is it necessary to clean the tectyl before the assembly?


Yes, because although the tectyl is compatible with the oils used, it must be cleaned so that
the guide-shoe or roller will function properly.

Do the oneelevator guide rails wear out?


No, oneelevator guide rails under normal working conditions do not wear out because both the
guide-shoes and the rollers are softer than the oneelevator guide rails. The oneelevator guide
rail may only be damaged through the action of the safety gear.

Why are oneelevator guide rails made of steel?


Oneelevator guide rails carry out functions of both guiding and safety, since they are the
structural member on which the safety gear works. Steel is currently the cheapest material that
perfectly meets these two requirements.
Elevator guide rails – Frequently Asked Questions
Why are there machines that are mounted on the oneelevator guide rails?
This eliminates the need for a machine room and no loads are therefore placed on the building.
Since the oneelevator guide rails are supported on the ground, they act as perfect support for
holding up the machinery and other elements.

Why are the oneelevator guide rails 5 meters long?


The oneelevator guide rails are 5 meters long because it is the appropriate manufacturing
length and allows the parameters for straightening to be checked properly.

How do movements in the building affect the riding path?


They do not affect low-rise elevators, but for elevators covering numerous floors building
contraction or differences in temperature may cause warping in the oneelevator guide rails.

Why is the assembly of the riding path so important?


The greatest problems for comfort are caused by the joints between oneelevator guide rails on
the riding path, therefore it is extremely important to have good quality oneelevator guide rails
and to obtain accurate alignment.

Do the oneelevator guide rails have any surface treatment?


No, the oneelevator guide rails do not have surface treatments. On cold-drawn oneelevator
guide rails the cold-drawn process modifies the mechanical features of the material.

Does the riding path for the counterweight influence comfort?


Yes, but to a lesser extent than the one for the car. The vibrations from the counterweight are
sent along the cable and may affect comfort somewhat. For the counterweight a lower quality
may be used than that for the car.

How should the fishplates be calculated?


The fishplates should be calculated with the same restrictions for deflection as the oneelevator
guide rails, providing that joint plates are not placed near a bracket.

What does the roughness level of the oneelevator guide rails affect?
The roughness level of the oneelevator guide rails affects the wear of the guide-shoes or
rollers. It also affects the friction factor and the behavior of the safety gear. One extremely
important point is to maintain a uniformity of roughness in order to provide consistent behavior
of the oneelevator guide rail.
Elevator guide rails – Frequently Asked Questions
What measures should be taken into account in areas subject to earthquakes?
- The oneelevator guide rails must be larger than the ones that are normally used.
- The clips or the brackets must be sliding.
- The fishplates must be especially rigid so there will be no possibility of slipping of the
oneelevator guide rail over the fishplate.

What is the concept of the continuous oneelevator guide rail?


Ideally, a oneelevator guide rail should be manufactured to match the required length for the
installation, but since this is not possible we replace it with the "continuous oneelevator guide
rail". This means that several oneelevator guide rails are mounted, and the joints are
guaranteed to maintain the same parameters as the rest of the oneelevator guide rail.

How can comfort be ensured?


The way to ensure comfort is to choose the right components right from the design stage. To
do so, the necessary parameters must be defined for all the elements that affect comfort.
When comfort is not achieved the first time, the cost escalates up because it is difficult to
detect which element is the one at fault.

Which is better, using a larger oneelevator guide rail or using a shorter distance
between brackets?
It depends on each individual case. Sometimes the distance is determined by the building, but
when this limitation does not exist, it is necessary to analyze the cost of installing more
brackets as compared to the cost of a larger oneelevator guide rail.

In a high-speed lift, is it sufficient to use a good roller?


In a high-speed lift, everything down to the smallest detail is important. The roller should be a
good one, but as is the case with cars, the suspension may be good but if the road is not, the
result will not be the best possible. At present, the trend for obtaining comfort at high speed is
to use rollers with low-stiffness springs so that they better filter the acceleration rates. However,
it may be very dangerous since large movements of the rollers over the car may cause
contacts with the safety systems and other mechanical elements. In our opinion, the stresses
for the springs must always be higher than the maximum stresses that arise from the
calculation for the lift.

You might also like