Design of One-Way Slab Marked as "S2"

Clear span of the slab = 1365 mm

Total Depth of the slab assumed = 125 mm 4
Clear cover to main reinforcement = 20 mm
Width of the support = 230 mm
Support Condition at one end : 2
Support Condition at another end : Simply supported
2
Simply
Characteristic Compressive strength of concrete,fck supported
= 25 N/mm2
Grade of Steel,fy = 500 N/mm2
Width of the slab to be considered,b = 5125 mm
Effective depth of the slab, d = 101 mm
Effective span of the slab, leff = 1466 mm

Load Calculations:
Dead load of the slab = 3.125 kN/m2
Floor Finish on the slab = 2.0 kN/m2
Total Dead load on the slab,wd = 5.125 kN/m2
Total Live load on the slab,wl = 1.50 kN/m2

Bending Moment calculations:

Maximum positive Bending Moment = (wd+wl)*leff2/8
= 1.78 kN-m

Maximum negative Bending Moment = 0.00

= 0.00 kN-m
Factored positive B.M.,Mu(+ve) = 2.67 kN-m
2
Mu/b.d (+ve) = 0.05
Factored negative B.M.,Mu(+ve) = 0.00 kN-m
Mu/b.d2 (-ve) = 0.00

Check for depth:

Effective depth of slab = sqrt(Mu/0.133.fck.b)
d= 12.52 mm
Overall depth of the slab, D = 36.52 mm
Therefore Assumed depth is adequate.

Positive Reinforcement calculations:

Required Area of steel at midspan,Ast(+ve) =

Ast(reqd) =
f ck
2fy [ √ Mu
1− 1−4 .598 2
bd f ck
. bd
]
60.91 mm2
Required percentage of steel, pt = 100Ast/b.d
= 0.12 %
It is greater than minimum percentage of steel, 0.12%
Limiting percentage of steel for U.R.S.,pt limit = 19.94 x fck/fy
= 1.20 %
Hence the section is Under reinforced section
Dia.Of bar used for +ve reinforcement = 8 mm
Spacing of the bars,Sv = (b x Asv) /Ast 335.10 mm
say 200.00 mm
Minimum spacing required = 3.d = 300.00 mm Whichever is less
300.00 mm
Provide T8 @ 200 C/C as +ve reinforcement
Provided percentage of steel = 0.25 %
Distribution reinforcement:
Minimum percentage of steel = 0.12 %
Area of steel required, Ast(dist) = 621.15 mm2
Dia.Of bar used for dist. Reinforcement = 8 mm
Spacing of the bars,Sv=(bxAsv) /Ast(dist)= 414.73 mm
say 250.00 mm
Minimum spacing required = 5.d = 500.00 mm Whichever is less
300.00 mm
Provide T8 @ 250 C/C as distribution reinforcement

Negative Reinforcement calculations:

Required Area of steel at support,Ast(-ve) =
f ck
2fy [ √ Mu
1− 1−4 .598 2
bd f ck
. bd
]
Ast(-ve) reqd = 0.00 mm2
Required percentage of steel, pt = 100Ast/b.d
= 0.12 %
It is greater than minimum percentage of steel, 0.12%
Limiting percentage of steel for U.R.S.,pt limit = 19.94 x fck/fy
= 1.20 %
Hence the section is Under reinforced section
Dia.of bar used for +ve reinforcement = 8 mm
Spacing of the bars,Sv = (b x Asv) /Ast #DIV/0! mm
say 250.00 mm
Minimum spacing required = 3.d = 300.00 mm Whichever is less
300.00 mm
Negative Reinforcement is not required

Check for Deflection:

(leff/d)basic = 20
Percentage of tensile reinforcement = 0.25 %
Modification factor for Tension rein.Kt = 1.28 (From IS:456)
Modification factor for Comp. rein.Kc = 1.00 (From IS:456)
(leff/d)Max. = (leff/d)basic * Kt * Kc = 25.60
(leff/d)provided = 14.51 < (leff/d)max
Hence Provided depth is adequate.

Check for Shear:

Maximum Shear Force, V = 0.5*(wd+wl)*leff
= 4.856125 kN
Factored Shear Force, Vu = 7.28 kN
Nominal Shear stress, Tv = Vu/b.d = 0.01 N/mm2
Percentage of tension reinforcement,pt= 0.25 %
Design Shear strength, Tc = 0.36 N/mm2
This value is further enhanced by multiplying factor.
Multiplying factor ,K = 1.5
Therefore Design Shear Strength= KTc= 0.55 N/mm2 > Tv Hence OK
Maximum shear strength,Tcmax = 3.35 N/mm2 > Tv Hence OK
Hence Shear Strength is within the allowable limit.

Depth of the Slab = 125 mm

Reinforcement:
Provide T8 @ 200 C/C as +ve reinforcement
Provide T8 @ 250 C/C as distribution reinforcement
Negative Reinforcement is not required
Design of One-Way Slab Marked as "S2"
Clear span of the slab = 1575 mm
Total Depth of the slab assumed = 125 mm 6
Clear cover to main reinforcement = 20 mm
Width of the support = 230 mm
Support Condition at one end : 3
Support Condition at another end : Continuous 3
Continuous
Characteristic Compressive strength of concrete,f ck
= 25 N/mm2
Grade of Steel,fy = 500 N/mm2
Width of the slab to be considered,b = 5355 mm
Effective depth of the slab, d = 101 mm
Effective span of the slab, leff = 1575 mm

Load Calculations:
Dead load of the slab = 3.125 kN/m2
Floor Finish on the slab = 1.0 kN/m2
Total Dead load on the slab,wd = 4.125 kN/m2
Total Live load on the slab,wl = 15.00 kN/m2

Bending Moment calculations:

Maximum positive Bending Moment = (wd/16+wl/12)*leff2
= 3.74 kN-m

Maximum negative Bending Moment = -(wd/12+wl/9)*leff2

= -4.99 kN-m
Factored positive B.M.,Mu(+ve) = 5.61 kN-m
2
Mu/b.d (+ve) = 0.10
Factored negative B.M.,Mu(+ve) = -7.48 kN-m
2
Mu/b.d (-ve) = 0.14

Check for depth:

Effective depth of slab = sqrt(Mu/0.133.fck.b)
d= 20.50 mm
Overall depth of the slab, D = 44.50 mm
Therefore Assumed depth is adequate.

Positive Reinforcement calculations:

Required Area of steel at midspan,Ast(+ve) =

Ast(reqd) =
f ck
2fy [ √ Mu
1− 1−4 .598 2
bd f ck
. bd
]
128.32 mm2
Required percentage of steel, pt = 100Ast/b.d
= 0.12 %
It is greater than minimum percentage of steel, 0.12%
Limiting percentage of steel for U.R.S.,pt limit = 19.94 x fck/fy
= 1.20 %
Hence the section is Under reinforced section
Dia.Of bar used for +ve reinforcement = 8 mm
Spacing of the bars,Sv = (b x Asv) /Ast 335.10 mm
say 200.00 mm
Minimum spacing required = 3.d = 300.00 mm Whichever is less
300.00 mm
Provide T8 @ 200 C/C as +ve reinforcement
Provided percentage of steel = 0.25 %
Distribution reinforcement:
Minimum percentage of steel = 0.12 %
Area of steel required, Ast(dist) = 649.026 mm2
Dia.Of bar used for dist. Reinforcement = 8 mm
Spacing of the bars,Sv=(bxAsv) /Ast(dist)= 414.73 mm
say 200.00 mm
Minimum spacing required = 5.d = 500.00 mm Whichever is less
300.00 mm
Provide T8 @ 200 C/C as distribution reinforcement

Negative Reinforcement calculations:

Required Area of steel at support,Ast(-ve) =
f ck
2fy [ √ Mu
1− 1−4 .598 2
bd f ck
. bd
]
Ast(-ve) reqd = 171.36 mm2
Required percentage of steel, pt = 100Ast/b.d
= 0.12 %
It is greater than minimum percentage of steel, 0.12%
Limiting percentage of steel for U.R.S.,pt limit = 19.94 x fck/fy
= 1.20 %
Hence the section is Under reinforced section
Dia.of bar used for +ve reinforcement = 8 mm
Spacing of the bars,Sv = (b x Asv) /Ast 1570.77 mm
say 250.00 mm
Minimum spacing required = 3.d = 300.00 mm Whichever is less
300.00 mm
Provide T8 @ 250 C/C as -ve reinforcement

Check for Deflection:

(leff/d)basic = 26
Percentage of tensile reinforcement = 0.25 %
Modification factor for Tension rein.Kt = 1.28 (From IS:456)
Modification factor for Comp. rein.Kc = 1.00 (From IS:456)
(leff/d)Max. = (leff/d)basic * Kt * Kc = 33.28
(leff/d)provided = 15.59 < (leff/d)max
Hence Provided depth is adequate.

Check for Shear:

Maximum Shear Force, V = (0.55wd+0.6wl)*leff
= 17.74828125 kN
Factored Shear Force, Vu = 26.62 kN
Nominal Shear stress, Tv = Vu/b.d = 0.05 N/mm2
Percentage of tension reinforcement,pt= 0.25 %
Design Shear strength, Tc = 0.36 N/mm2
This value is further enhanced by multiplying factor.
Multiplying factor ,K = 1.5
Therefore Design Shear Strength= KTc= 0.55 N/mm2 > Tv Hence OK
Maximum shear strength,Tcmax = 3.35 N/mm2 > Tv Hence OK
Hence Shear Strength is within the allowable limit.

Depth of the Slab = 125 mm

Reinforcement:
Provide T8 @ 200 C/C as +ve reinforcement
Provide T8 @ 200 C/C as distribution reinforcement
Provide T8 @ 250 C/C as -ve reinforcement