Scribd
Upload
87 views2 pages

Ab PLC5

This document provides information about connecting an MT500 HMI to an Allen-Bradley PLC-5 series programmable logic controller using a DF1 Full Duplex protocol over an RS-232 serial connection. It specifies the recommended HMI and PLC communication settings, and describes the device addressing formats for reading and writing to I/O bits and data files in the PLC. A wiring diagram is also shown for connecting the RS-232 port on the MT500 to channel 0 on the PLC-5 CPU.

Uploaded by

Carlos Enrique Pacheco Herrera
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
87 views2 pages

Ab PLC5

This document provides information about connecting an MT500 HMI to an Allen-Bradley PLC-5 series programmable logic controller using a DF1 Full Duplex protocol over an RS-232 serial connection. It specifies the recommended HMI and PLC communication settings, and describes the device addressing formats for reading and writing to I/O bits and data files in the PLC. A wiring diagram is also shown for connecting the RS-232 port on the MT500 to channel 0 on the PLC-5 CPU.

Uploaded by

Carlos Enrique Pacheco Herrera
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

www.PLCworld.

cn

AB PLC5
Allen-Bradley PLC-5 Family PLCs using the DF1 Full Duplex protocol.
For the PLC-5/10, PLC-5/15 and PLC-5/25 the MT500 should be connected to:
the DF1 port on the 1785-KE module;
for the PLC-5/11, PLC-5/20, PLC-5/30 and PLC-5/40 the MT500 should be connected to:
the Channel 0 Port on the PLC.

http://www.ab.com

HMI Setting:
Parameters Recommend Option Notes
PLC type AB PLC5
Com port RS232
Baud rate 19200 9600, 19200
Parity bit None Even, Odd, None
Data Bits 8 8
Stop Bits 1 1
HMI Station No. 0
PLC Station No. 1 1-31

PLC Setting:
Communication mode DF1 Full Duplex protocol 19200, None, 8, 1 (default)

Device address:
Bit/Word Device Type Format Range Memo
B I1 ddd(dd) ddd:0~254 (dd): 0~15 Input (I)
B O0 ddd(dd) ddd:0~254 (dd): 0~15 Output (O)
B B3 ddd(dd) ddd:0~254 (dd): 0~15 Bit data file (B3)
B B10~13 ddd(dd) ddd:0~254 (dd): 0~15 Bit data file (B10~13)
W T4SV ddd ddd:0~254 Timer Preset Value (T4)
W T4PV ddd ddd:0~254 Timer Accumulator Value (T4)
W C5SV ddd ddd:0~254 Counter Preset Value (C5)
W C5PV ddd ddd:0~254 Counter Accumulator Value (C5)
W N7 ddd ddd:0~254 Integer data file (N7)
W N10~15 ddd ddd:0~254 Integer data file (N10~15)
W F8 ddd ddd:0~254 Floating point data file (F8)
Nfn fffddd File no. fff:7,9~254 Integer data file (V2.5.0 or newer)
W
Element no. ddd:0~254
www.PLCworld.cn

Bit/Word Device Type Format Range Memo


Ffn fffddd File no. fff:8,9~254 Floating point data file (V2.5.0 or
W
Element no. ddd:0~254 newer)

Wiring diagram:
RS-232: PLC5 CPU CH0
MT500 PLC[232] AB CPU CH0 RS-232
9P D-SUB Female 25P D-SUB Female
2 TX 3 RXD
3 RX 2 TXD
5 GND 5 GND

You might also like