High Speed

Overlock Machine
73 7 M—04 243M—24 / TF
732M—075 244 M—24
733M—04 /TF 257 M—35
734M—04 257 M—55
24 7 M—24 / 25 257 H—56

® Singer is a registered trademark of The Singer Company Limited or its affiliated companies.
© 2009 Copyright The Singer Company Limited
 1.1 Important Safety Instructions 1
1.2 Safe Operation 2

2.1 Product Description 3

2.2 Machine Specification 4
2.3 Motor, Motor Pulley and Belt 4

3.1 Table Cut-Out Diagram 5

3.2 Machine Installation 6
3.3 Lubrification and Oil Drainage 8
3.4 Needle Attachment (or Replacement) 9
3.5 MachineThreading 9
3.6 Thread Tension Adjustment 10
3.6.1 Tension Nut Adjustment 10
3.6.2 NeedleThread Control 10
3.6.3 LooperThread Control 11
3.6.4 Chain LooperThread Cam Control 11
3.7 Adjusting the Differential Feed Rate 12
3.8 Stitch Length Adjustment 12
3.9 Parts Relation andTiming 13
3.9.1 Needle and Needle Plate 13
3.9.2 Upper Looper (Spreader) and Needle 14
3.9.3 Lower Looper and Needle 14
3.9.4 Upper and Lower Loopers 15
3.9.5 Needle and Needle Guard 15
3.9.6 Chain Looper and Needle 15

—
4.1 Machine Head Cleaning 16
4.2 Oil Change and Filter Cleaning 16
4.3 Safety Inspection 16
 6.1 Frame Components 20
6.2 Cloth Plate Components 22
6.3 Cover Components 24
6.4 Main Shaft Components 26
6.5 Needle Bar Components 28
6.6 Thread Guide Components 30
6.7 Upper Looper Components 32
6.8 Lower Looper Components 34
6.9 Front Looper Components 35
6.10 Cam Components 36
6.11 Differential Feed Components 38
6.12 Feed Dog Components 40
6.13 Trimming Components 42
6.14 Presser Foot Components 44
6.15 Lubrication Components 46
6.16 Feed Snap Components 48
6.17 Thread Spool Components 50
6.18 Plate Row Material Components 52
6.19 Accessories 53
 Safety Instructions

0 Before running the machine, make 0Maintenance and repair on elec-

1.1
Important Safety
sure all relevant safety specifica-
tions are adequate to specifica-
tric equipment should only be
made by qualified personnel. If
tions and technical standards in any electric device is damaged,
Instructions your country. the machine should be immedi-
ately stopped.
0The machine should not be run
Important without its safety devices. 0 Before starting the machine in full
running, a test must be conducted
When using the 0 The machine should only be oper-
to assure that machine and opera-
ated by properly trained personnel.
machine, basic tor are able to perform the task.
safety procedures 0 For your safety, goggles must be
0 The machine should not be placed
used While running the machine.
must be followed. next to a sound source as an ultra-
Flead with attention 0 Turn off or unplug the machine in sonic welding machine and other
the following situations: equipment.
all instructions before
using the machine. 0 Passing the thread by the nee- 0 The machine should only be run
dle or replacing the bobbin or with the proper electric cable
When using it,
looper. and connectors, and also the ad-
understand that
0 Replacing the needle, presser equate grounding.
all basic safety
foot, throat plate, feed dog and . The machine should only be used
instructions are
sliding plate. to sew materials as indicated in
not limited to the its instructions manual, and indi-
0 When the machine is in main-
following items. cations of use should be followed.
tenance.
Read all instructions, Singer will not be held responsible
0 When the operator is not run-
take care of this for any damage caused by unau-
ning the machine.
manual, and use it thorized changes in the product.
Oln case of lubricant oil contact
as reference when
with the eyes or skin, wash the
necessary. surface with plenty of icy water.
In case of ingestion, seek medical
help immediately.
ORepair, fitting or maintenance
should only be performed by
properly trained personnel.

High Speed Overlook Machine | Instructions Manual and Parts List 1

 A0 To avoid the risk of electric shock, 0To avoid accidents in case of a

1.2
Safe Operation
do not open the motor wiring box
and do not touch the components
sudden start of the machine al-
ways turn it off when laying it
assembled inside the wiring box. down, or remove the belt cover
and the belt.
0To avoid injuries do not run the
machine without the belt cover or Olf your machine is equipped with
in case any other safety device is a servomotor, it does not make
removed. noises while being driven. To avoid
a possible accident caused by an
0To avoid possible injuries keep
unexpected start, bev sure the ma-
fingers, head, and clothes far
chine is turned off.
from wheel, belt and motor when
the machine is running. Nothing 0To avoid electric, do not run the
should be placed near those parts. machine without proper ground-
Ing.
0To avoid injuries never put your
fingers next to the loopers when A'TO minimize the risk of accidents
the machine is running. or damages in electric compo-
nents caused by electric discharge
0The shuttle whirls at high speed
turn the machine off before un-
while the machine is running. To
plugging it.
avoid hand injuries, keep them
away from the shuttle while the OCIean the machine periodically.
machine is running. Turn off the
machine to replace the bobbin.
0 To avoid possible injuries be care-
ful when putting down or lifting
the machine head.

High Speed Overlook Machine | Instructions Manual and Parts List 2

 2 1 High Speed Overlock Machine
I

Product
Description

High Speed Overlock Machine | Instructions Manual and Parts List 3

 2.2
Machine
Specification
I
o N
9"
o
.0"
o
.0"

0 Clutch motor 1/2 HP (400W) high

2l 3 Speed (2 poles)
Motor, Motor ' Belt type M
Pulley and Belt

90
i 95
i 100
i 105
i 110
i 115

High Speed Overlock Machine | Instructions Manual and Parts List 4

 3.1
Table Cut-Out
Diagram

65]—

214 V

(2)13
259 J—

¢27
289
305 J—

359

442 L
469

540 V 537

595
4001— —

1200
433 A

300 A
258
269

Figure 1

High Speed Overlock Machine | Instructions Manual and Parts List

 3 2 Install the machine support compo- the needle bed surface to the table
nents and the residues cam as indi- top is 100mm. For inserted assem-
I
_ cated on figure 2. In case ofsemi-in- bly the distance is about 5.0mm.
maChme serted assembly the distance from
Installation

Figure 2

High Speed Overlook Machine | Instructions Manual and Parts List 6

 3 2 Set the machine head on the sup- Install the friction motor pedal at
port base. the right side and the pedal of the
I presser lifter at the left side.
- Connect the machine Wheel to the
maChlne motor With the belt. Be sure the motor is clockwise di-
Installation -
Adjust the belt tension so that there rected, referred to figure 3'
is a gap of about 20 mm when the
center of belt is pressured.
Set the belt cover according to fig-
ure 4.

Figure4

High Speed Overlook Machine | Instructions Manual and Parts List 7

 Remove the oil flow sight win- replace the oil and from then on

3.3 dow 14’ and fill with the lubricant

oil (Singer Oil), until the indicator
the machine can be used at maxi-
mum speed.
Lubrication of the oil level is between the two
To preserve the machine, change
and Oil lines of the oil level sight window
the oil after four weeks of use. After
’3’. After that, put back the oil flow
Drainage that the oil must be changed every
window ’A’ and squeeze it.
four months. To change the oil sim-
When using the machine for the ply remove the screw ’0’ indicated
Important
first time, or a machine that has on figure 6. After draining the oil,
As this is a high not been used for some time, oil replace the screw and complete the
speed machine, the needle bar top, the guides and machine with new oil.
loopers before running it.
DO NOT run the This machine has an oil filter (fig-
machine before A new machine should be run at ure 6) that must be cleaned every
80% maximum speed on the first month or changed as needed.
oiling and assuring
four weeks. After this initial cycle,
the direction of
motor rotation.

Figure 5

High Speed Overlook Machine | Instructions Manual and Parts List 8

 Use needle Singer 6120-06. |— —|
3. 4 Release screw ’1’ as indicated on W
Needle figure 7 and put (or Withdraw the _
old needle).
AflaChment Inse It th e nee dl e WI'th th e s Io tturne d
(or Replacement) to the back side and push it up until
the bar end. Tighten screw ’1.’

Figure 7

3 5 For five thread machine For three / four thread machine

Machine
Threading

Important
Refer to the sewing
type you need for
correct threading. Any
incorrect threading
may cause thread
brake, uneven
stitches or skip
stitches.

High Speed Overlook Machine | Instructions Manual and Parts List 9

 Important
3.6 The thread tension should be adjusted according to the type and thickness of
Thread Tension cloth, thread, sewing Width, stitch length and others. Therefore, the pressure on
Adjustment the Tension Buttons or Thread Guides should be individually adjusted for each case.

The following adjustments are re- Tension Nut 3: controls the thread

3.6. 1 lated to figure 10.

Tension Nut 1: controls the needle
in the right looper
Tension Nut 4: controls the thread
Tension Nut thread or the left thread in case of in the left looper
Adjustment two need/es.
Tension Nut 5: controls the thread
Tension Nut 2: controls the thread of the safety stitch.
in the right needle.

\/

Figure 10

For all types ofstitch 504, 512 or 514,

3.6.2 move down the guides ’1’and ’2’.

For the types of stitch 503 and 505,
Needle
move the guides ’1’ and ’2’ to the
Thread Control highest point.

Note
The signal (+)
increases the tension
in the thread. The
signal (-) reduces the
tension of the thread.

High Speed Overlook Machine | Instructions Manual and Parts List 10

 For the type ofstitch 512, when Ad- For the type of stitch 503 and 505,

3.6.3 Looper
just guide ’1’and ’2’as follows the
looper on the right is at the left far
move the guides to the lowest
point and adjust ’1’ and ’2’ in level
end, adjust ’1’ and ’2’ in level with with the continuous line.
Thread Control the dotted mark, as on figure 12. Adjust guide ,3,“ follows:

0 Position 14’: for stretchy thread

Note 0 Position ’B’: for seaming and blind
The signal (+) means stitch hemming

more thread and (-l 0 Position ’0’: stitch type 512

means less thread. Adjust guide ’4’ as follows:
0 Position ’0’: for stretchy thread
0 Position ’E’: for seaming and blind
stitch hemming.

Figure 12

When the needle is on high posi-

3.6.4 tion, mark 14’ must be aligned with

the thread guide bracket ’1’, as
Chain Looper shown on figure 13.
Thread Cam Release screw ’2’ and the thread
Control cam ’3’. Turn it clockwise for quick
release of thread through the cam.

Figure 13

High Speed Overlook Machine | Instructions Manual and Parts List 11

 Adjustment of the differential is the Release nut ’1’on figure 14, and turn

3.7 dragging proportion between the

main feed dog and differencial feed
screw ’2’ clockwise to streching the
cloth or counter clockwise to shrink
Adjusting the dog. When the movement of main it. Retightend the nut ’1’.
Differential feed dog is less than that of the
differencial feed dog, the cloth will
Feed Rate
be frilled during sewing. Otherwise,
the cloth will be stretched.
Note
When the surface of
level ’3’adjustment
is on scale 2, the
differential adjustment
is l .' l, and if it is
on the scale, its Figure 14

proportion may be
adjusted up to 7 .' 0.7

Press button to the end and keep it

3.8 pressed as shown on figure 15.
Turn the wheel until we have the /
Stitch Length
desired stitch length. It is shown on
Adjustment the wheel scale.

Important Figure 15
The stitch length
adjustment is
made according to
the sewing fabric,
1. 0 1.4 1.7 2. 5
differential feed ratio 2.3 3.1 3.9 4.7 5.4 5.9
and other factors. 0.9 1.2 1.5 1.8 2.1 1.0

High Speed Overlock Machine | Instructions Manual and Parts List 12

 3.9
Parts Relation
and Timing

When needle at the highest posi- Release screw ’1: as shown on fig-

3.9. 1 tion, distance 14’ between needle

point (the left needle if there are
ure 16.
Turn the wheel to see if needle is
Needle and two needles) and needle plate is
centralized at every hole of the
Needle Plate 9.5 to 9.7 mm for standard adjust-
needle plate. Release screw ’2’ to
ment, or 10.8 to 11.0 mm for spe-
adjust needle holder.
cific cases. Each needle should be
centralized over each hole in the Turn the wheel to move needle to
needle plate. The right needle must the highest position and move nee-
be about 0.2 to 0.3 mm ahead the dle bar until the height is correctly
left needle. adjusted.

Distance between needle point (the Tighten screws ’1’and ’2’.

right needle if there are two nee-
dles) and the front part of the hole
in the needle plate or presser foot
is 1.2 mm.

A: 9,5 - 9,7 mm
High Lift: 10,8 - 11,0 mm

Figure 16

High Speed Overlook Machine | Instructions Manual and Parts List 13

 When the right looper moves to the needle. For two needles, the dis-

3.9.2 far left end, distance fl’between the

looper point and the center line of
tance ’B’ is 5.5 to 6.0 mm from the
left need/e, as shown on figure 12
Upper Looper the needle is 4.5 to 5.0 mm for one
(Spreader)
and Needle

Figure 17

When the lower looper moves to When the lower looper moves to

3.9.3
Lower Looper
the extremly left, the distance 14’
between looper point and center
the center line of needle (left nee-
die, if two needles), the gap be-
line of the needle (left needle, if tween needle and looper is from 0
and Needle two needles) is from 3.4 to 3.6 mm, to 0.05 mm, as shown on figure 19.
for high lift machines, as shown on
figure 18. E
E
(m 0 © ”8’

:i;—:
i—f_

Figure 19

Figure 18

High Speed Overlook Machine | Instructions Manual and Parts List 14

 When the upper and lower Ioopers

3.9.4 are crossed, the distance is 0.2 mm

for ’A’ and 0.5 mm for ’B’, accord- 0.2
A
0.5

Upper and ing figure 20.

. //
Lower Loopers __ /
/_'\_

Figure 20

When the looper point is on the 0.0

3.9.5 side opposite to the center line of

the needle (left needle if there are
A

0.15 - 0.20 mm
Needle and two needles), space between nee-
dle and rear needle guard of 14’ is
In!“
Needle Guard M?
0 mm. When needle moves to the
lowest position, space between
needle and front needle guard of
’B’is from 0.15 to 0.20 mm, accord-
ing to figure 21.

Figure 21

The safety looper should be fixed in

3.9.6
Chain Looper
a position lower than this support.
And when it moves to the left far
end, the distance between the loop-
and Needle er point and the center line ofneedle
is 2.5 mm, according to figure 22.

Figure 22

High Speed Overlook Machine | Instructions Manual and Parts List 15

 E Maintenance

Clean the machine head periodi-

4.1 cally with a dry soft cloth to remove

the excess of dust in the head. Do
Machine not use any kind of solvent material
Head Cleaning to clean the surface.

If the machine has not been used for Oil filter should be cleaned every
4.2 a long time, lubricate the superior
part of the needle bar, guides and
month or replaced for a new one
as necessary. To clean the filter or
Oil Change and loopers before returning to opera- change the oil, fol/ow instruction in
Filter Cleaning tion. item 3.3.
Oil should be changed every four
months. When changing the oil fol-
low instructions on item 3.3.

Frequently check if all safety de- Check and be sure there is no mo-

4.3 vices are properly installed and

adjusted.
tor overheating and be sure that
the cable and electric connector
Safety Check all screws that fix and hold are not damaged.
Inspection the machine head that should be
properly tight.
Check and be sure the belt is not
excessively worn out and see that
it has the proper tension.

High Speed Overlook Machine | Instructions Manual and Parts List 16

 Possible Causes

H
939199!“ Needle installed the wrong way.

Wrong kind of needle.

Damaged needle.

Wrong relation with needle guards.

Wrong relation with looper.

Needle is not centralized with the hole at the needle

plate or the presser foot.
H

Low quality thread.

915-"!in

Thread is thicker than the eye of the needle.

Wrong passage of thread.

Thread tension too tight.

Needle wrongly set.

Thread stand wrongly set.

Z Needle overheating.

8. Tension disk or guides with burrs .

9. Wrong relation of needle with looper.

10. Needle, looper, needle plate and guides have burrs.

1. Wrong relation of needle with looper.

2. Wrong passage of thread.

3. Needle installed the wrong way.

4 . Inadequate tension of thread.

5. Point of looper damaged.

6. Needle damaged.

Z Wrong installation of needle guards.

1. Wrong threading.

2. Thread is thicker than needle hole.

3. Wrong thread tension.

4. Needle thread is not lubricated.

5. Wrong relation of needle with looper.

\l

High Speed Overlock Machine | Instructions Manual and Parts List 1

 Possible Causes

1- Wrong threading.
2- Wrong installation of thread stand.
3- Wrong setting of lower knfe.

4- Knives does not cut perfectly.

5- Thread guide or tension disc with burrs.

6- Needle point damaged.

Z Inadequate height of feed dog.

8- Inadequate thread tension.

9191+sz

Thread tension is too strong.

Inadequate pressure on presser foot.

Inadequate height of feed dog.

Knives does not cut perfectly

Difierential feed is not correct.

Needle is too thick.

HPWNH

Incorrect presser foot.

Inadequate synchronism of Iopper cam.

Chain stitch Iooper installed wrongly.

Wrong passage of thread.

Thread tension inadequate.

5- Wrong relation of needle with looper.

Z Needle plate or presser foot with burr.

8- Rough thread tension disc.

00

High Speed Overlook Machine | Instructions Manual and Parts List 1

 6.1
Frame
Components

High Speed Overlook Machine | Instructions Manu al and Parts List 20

 6.1
Frame 1 Machine frame
2 Needle thread cover plate ---

Components 2 ---
4
5
22222
Needle plate
---
---
6 Rear oil adhesive ---

8 Rear cover ---

12
11
cover
Cover washer
---
---

13 Oil screen ---

15 Oil seal I ---

16 Oil seal M ---
17 Oil amount adjusting pin ---

22 222w ---
22 222w ---
24
25
222w
Screw M3x3
---
---

22 2222 --—
22 222w ---
22 222w ---
22 222w ---
22 222w ---
22 222w ---
22 2222 --—
24 222w ---
22
36
222w
Side cover
---
---
37 Side cover pad ---

High Speed Overlock Machine | Instructions Manual and Parts List 21

 6.2
Cloth Plate
Components

High Speed Overlook Machine | Instructions Manual and Parts List 22

 6.2

coooxlmcnhwwa
Cloth Plate SW“ _
ubber bushing
Components Rubber bushing
Screw
Spflng
Cloth plate slider cover
Cloth plate cover spring
Cloth plate lower plate
Washer
O
_|

Upper looper sealing plate

_\
_\

Upper looper sealing plate washer

12 Screw

1S Screw --
r4 Screw ---
re Screw ---
w Screw ---
co Screw ---
21 Screw ---
23 Cloth plate ---
24 Cloth plate lower plate ---
25 Rubber bushing ---

High Speed Overlock Machine | Instructions Manual and Parts List 23

 6.3
Cover
Components

High Speed Overlook Machine | Instructions Manu al and Parts List 24

 6.3

comximcnhwwa
Upper cover
Cover Upper cover washer
Components Thread guide supporter
Belt cover
Thread cover spring
Cloth guide plate
Oil guide ll
Pin
Front spring
0
_|

Front cover
_\
_\

Front cover guard

Front cover guard
12 Front cover hinge
13 Hinge pin
14 Front cover hinge spring
15 Front cover hinge washer
16 Trade mark plate
17 Oil flow window
18 Front cover snap guard
19 Oil guard
20 Oil level gauge washer
21 Pin
22 Oil sight window
23 Eye Guard
24 Upper cover
25 Screw
26 Thread guide supporter
27 Screw
28 Snap spring

29 Screw --
so screw ---
s1 screw ---
32 screw ---
as screw ---
s4 screw ---
as Screw --—
37 Machine model plate ---

High Speed Overlock Machine | Instructions Manual and Parts List 25

 6.4
Main Shaft
Components

High Speed Overlook Machine | Instructions Manu al and Parts List 26

 6.4
Main Shaft ; xii" Shaft
components 3 Rear shaft bearing cover ---
a
5
Washer
Main shaft spring washer
---
---

9 Oil pump worm ---

11 Main shaft left bushing ---

13 Bearing cover ---

Bearing cover ---
14 Bearing cover washer ---

17 Bulgy pulley shaft ---

rs screw ---
2o Screw --—
22 Sarah ---
2a screw ---
2a screw ---
2e screw ---
2e screw ---
22 Screw --

High Speed Overlock Machine | Instructions Manual and Parts List 27

 6.5
Needle Bar
Components

High Speed Overlook Machine | Instructions Manual and Parts List 28

 6.5

(DQNOSO'l-bwwd
Needle bar driving frame rock shaft
Needle Bar Eccentric shaft
Components Needle bar shaft bushing back
Thrust collar
Needle bar driving crank
Oil seal
Needle bearing
Washer ring
Needle bar guide pin
\IOVO'l-hOON—‘O
44444444

Oil wick
Needle bar rock shaft
Needle bar shaft bearing (left)
Seal ring
Needle bar shaft bearing (right)
Thrust collar
Balance block
Needle bar frame rock shaft crank
Needle bar frame rock shaft crank
18 Needle bar connecting rod
19 Connecting link pin
20 Screw
21 Needle bar guide bracket
22 Needle bar
23 Cat No. 6120-06 Needle
Cat No. 6120-06 Needle
Cat No. 6120-06 Needle
24 Oil wick
25 Plastic tube
26 Oil wick
27 Needle clamp
Needle clamp
Needle clamp
Needle clamp (for thick)
28 Thrust collar set screw
29 Hexagon socket screw
30 Balance block position screw
31 Thrust collar set screw
32 Needle bar connecting rod set screw
33 Screw
34 Screw
35 Screw
36 Screw
37 Screw
38 Snap ring
39 Screw

High Speed Overlook Machine | Instructions Manual and Parts List 29

 6.6
Thread Guide
Components

Thread tension nut

Thread tension nut
Ratchet
Thread tension spring
Thread tension spring
Thread tension spring
Thread tension disc presser
Thread tension disc
Thread tension disc washer
Thread tension screw
Thread guide
Thread guide
Thread guide
Thread guide
Upper thread take-up
Upper thread take-up

High Speed Overlook Machine | Instructions Manual and Parts List 30

 6.6 Silicon oil box
Thread Guide Oil felt
Components Thread guide
Silicon oli washer
Oil felt
Tension spring
Thread controller disc holder
Spflng
Thread controller disc guide bushing
Throat plate positioning rod
Throat plate bracket
Thread mark guide
Thread mark guide
Teat needle guard
Front needle guard
Front needle guard
Needle plate
Needle plate
Needle plate
Needle plate
Needle plate
Needle plate
Needle plate
Needle plate
Needle plate
Thread guide
Needle guard |
Needle guard l|
Needle guard bracket
Needle guard bracket
Snap plate
Snap plate washer
Washer
Throat screw
Front needle guard screw
Throat plate bracket screw
Thread guide holder screw
Silicon oil box set screw
Silicon oil box set screw
Rear needle guard screw
Needle guard screw
Thread take up screw
Snap plate screw ||
Snap plate set screw
Screw
Screw
Washer
Screw
Rubber bushing

High Speed Overlock Machine | Instructions Manual and Parts List 31

 6.7
Upper Looper
Components

..A. ..can

5%;
59.;

e
in
(5)3“.Q
(l6
m

‘1

inf);-
6

9
is

High Speed Overlook Machine | Instructions Manual and Parts List 32

 6.7

(DQNOSO'l-bwwd
Looperlink
Upper Looper Looperlink holder
Components Thickness washer
Upper looper shaft
Big washer
Upper looper shaft rear bushing
Upper looper shaft front bushing
Upper looper shaft oil seal
Upper looper shaft crank
0
_|

Upper looper shaft bar

_\
_\

Connecting rod shaft pin

12 Washer
13 Oil wick
14 Upper looper slide block --
15 Oil felt
16 Oil felt
17 Thread tube
18 Screen oil plate
19 Felt plate
20 Thread holder snap plate
21 Upper looper shaft slide bar bracket
22 Thread guide
23 Oil wick
24 Screw
25 Thread amount regulating plate
26 Upper looper thread guard
27 Upper looper shaft thread plate
28 Screw
29 Upper looper set screw
(A)
D

Upper looper
(A)
_\

Upper looper crank

Upper looper crank
32 Screw
33 Screw
34 Upper looper crank screw
35 Washer
36 Link pin set screw
37 Hexagon socket screw
38 Upper looper shaft screw
39 Thread guide screw
40 Screw
41 Thread guide screw
42 Thread guide washer

High Speed Overlock Machine | Instructions Manual and Parts List 33

 6.8
Lower Looper
Components

Washer
Lower looper shaft washer
Oil seal
Lower looper shaft bushing (front)
Lower looper shaft bushing (rear)
Lower looper holder
Lower looper holder
Lower looper crank
Lower looper crank
Lower looper
Lower looper
Crank screw
Thread guide
Lower looper thread guide
Lower looper thread guide
Lower looper shaft
Lower looper shaft
Low looper shaft screw
Crank screw
Lower looper holder screw
Lower looper holder washer
Lower looper screw
Thread guide screw
Crank screw

High Speed Overlock Machine | Instructions Manual and Parts List 34

 6.9
Front Looper
Components

1 Front looper shaft holder

2 Front looper
3 Washer
4 Front looper crank
5 Regulating plate
6 Regulating plate pin
7 Driving crank holder
8 Front looper shaft bushing (front)
9 Front looper shaft bushing (rear)
10 Front looper shaft
11 Driving lever
N
_\

Front looper driving crank

(A)
_\

Front looper slide block

.b
_\

Thread guide screw

_\
O'l

Front looper guide set screw

0)
_\

Front looper holder set screw

_\
\l

Washer
m
_\

Screw
CO
_|

Front looper crank screw

N
0

Screw
N
_\

Screw
N
N

Snap ring
N
(A)

Screw
N
4:

Regulating plate pin

High Speed Overlock Machine | Instructions Manual and Parts List 35

 6. 10
Cam
Components

High Speed Overlook Machine | Instructions Manual and Parts List 36

 6.10 1 Horizontal shaft link

Components
23 Needle bearing
Snap ring
---
---
5 Horizontal shaft crank ---
6 Horizontal shaft ---
7 Left horizontal shaft bushing ---
8 Right horizontal shaft bushing ---

10 Looper thread take—up cam ---

11 Thread guide ---
12 Thread guide ---

14 Flat spring ---

15 Thread guide position plate ---
16 Thread guide ring ---
17 Thread guide ---
18 Thread guide ---
19 Thread pipe cover ---
20 Thread pipe ---

23
24
screw
Tension disc
---
---

27 Bearing snap ring screw ---

28 Carn set screw ---
29 Crank set screw ---

as Screw --—
w
4:

Thread guide plate screw ---

(A)
01

Thread guide plate screw ---

(A)
O)

Screw ---

High Speed Overlock Machine | Instructions Manual and Parts List 37

 6.11
Differential Feed
Components

High Speed Overlook Machine | Instructions Manual and Parts List 38

 6.11

(DQNOSO'l-bwwd
Stitch length regulating shaft
Differential Feed Spflng
Components Oil washer
Stitch length regulation cam assembly
Stitch length regulating block
Stitch length regulating block spring
Stitch length cam
Stitch length regulating plate
Feed length cam
#WN—‘OCOOJNCDO‘I#WNJOOQNCDUI-hWN—‘OCOGJNOSO'I-bWN—‘O
hhhhhwwwwwwwwwwNNNNNNNNNN—l—‘—\—\—\—\—\—\_\_|

Feed cam spring

Feed cam pin
Feed link
Feed rod rolling pin bearing
Feed crank
Differential link
Differential crank
Differential shaft
Differential shaft bearing
Oil seal
Thrust collar
Spflng
Washer
Regulating block
Washer
Feed cam
Washer
Differential regulation holder
Regulating screw
Regulating screw spring
Differential regulating link
Crank link cam
Differential link screw
Differential crank screw
Thrust collar set screw
Washer
Washer
Differential position screw
Spring screw
Differential regulating screw
Differential regulating screw
Screw
Screw
Washer
Marker plate

High Speed Overlock Machine | Instructions Manual and Parts List 39

 6. 12
Feed Dog
Components

High Speed Overlook Machine | Instructions Manual and Parts List 40

 6. 12 1 Main feed dog link plate
Feed Dog 2 Main reed dog bar ---
components 3 Differential feed dog bar ---
4 Feed dog lift slide block ---
5 Differential feed slide block ---
6 Slide block eccentric shaft ---
7 Slide block eccentric washer ---
8 Slide block eccentric shaft bushing ---

10 Feed shaft bushing (left) ---

11 Feed shaft bushing (right) ---
12 Feed regulating crank ---

14 Main feed dog bar link ---

15 Main feed dog bar link bushing ---

17 Crank slide block cover ---

18 Crank slide block ---
19 Feed regulating crank ---
20 Differential feed dog bar link ---
21 Differential feed dog bar link bushing ---

23 Screw oil plate ---

24 Feed dog carrier connection rod ---
25 Sealing connecting ring ---
26 Adjustable oil seal ---
27 Sealing connecting rod ---
28 Feed dog link eccentric shaft ---
29 Feed dog complete set ---
Feed dog complete set ---
Feed dog complete set ---
Feed dog complete set ---
30 Thrust collar set screw ---
31 Thrust collar ---
32 Screw ---
33 Screw ---
34 Screw ---
SS Screw --
ee Screw ---
er Screw ---
ec
39
Screw
Crank screw
---
---

re
41
Srcrr
Crank slide block screw
---
---

42 Screw ---
4S Screw ---
re Screw --—

High Speed Overlock Machine | Instructions Manual and Parts List 41

 6. 13
Rimming
Components

High Speed Overlook Machine | Instructions Manual and Parts List 42

 6. 13

N—\
Upper knife drive connecting link
Trimming Upper knife crank
Components Upper knife crank

mNmm-bw
Crank pin
Upper knife frame rock shaft
Bushing (left)
Bushing (right)
Washer
Upper knife holder
Upper knife holder
Upper knife holder
Thrust collar
10 Upper knife holder pin
11 Upper knife
Upper knife
12 Washer
13 Lower knife holder
Lower knife holder
Lower knife holder
14 Lower knife holder bushing
15 Lower knife holder spring
16 Lower knife holder plate
17 Lower knife
Lower knife
18 Lower knife holder lock plate
19 Thrust collar set screw
20 Upper knife crank set screw
21 Upper knife crank pin screw
22 Connecting link screw
23 Upper knife holder screw
24 Upper knife screw
25 Screw
26 Screw
27 Washer
28 Oil seal
29 Lower knife holder screw
30 Washer
Washer
31 Washer

High Speed Overlock Machine | Instructions Manual and Parts List 43

 6. 14
Presser Foot
Components

Presser foot arm

Presser foot shaft bushing
Screw
Presser foot shaft
Presser foot shaft bushing

High Speed Overlook Machine | Instructions Manual and Parts List 44

 6. 14

(DOING)
Thrust collar
Presser Foot Presser foot lifting spring
Components Presser foot crank
Presser foot lifting lever
10 Lever hook
11 Spflng
12 Thread cutting knife
13 Presser bar
14 Presser bar spring
15 Presser bar screw
16 Screw
17 Presser bar shockproof block
18 Presser foot lifting handle
19 Presser foot lifting handle spring
20 Presser foot lifting handle link
21 Washer
22 Presser foot corner plate
23 Presser foot spring
24 Presser foot holder connection plate
25 Screw
26 Screw
27 Presser foot lifting spring
28 Presser foot holder cover
29 Presser foot complete
Presser foot complete
Presser foot complete
Presser foot complete
Presser foot complete
Presser foot complete
Presser foot complete
Presser foot complete
30 Presser foot lifting handle
31 Presser foot lifting annul
32 Presser foot lifting handle bracket
33 Presser bar bushing
34 Presser foot lifting spring
35 Pin
36 Set screw
37 Lifting handle screw
38 Screw
39 Crank set screw
40 Snap washer screw
41 Screw
42 Set plate screw
43 Screw
44 Nut
45 Screw
46 Screw
47 Screw
48 Nut

High Speed Overlock Machine | Instructions Manual and Parts List 45

 6. 15
Lubrication
Components

High Speed Overlook Machine | Instructions Manual and Parts List 46

 6. 15

coooxlmcnthA
Oil pump complete
Lubrication Oil pump screw
Components Oil pan magnet cover screw
Oil pan screw
Oil pan magnet
Oil pan magnet cover
Oil pan
Oil pan washer
Oil seal
coooumm-th—‘ocoooummth—‘o
NNNNNNNNNN—IAAAA—IKAAA—l

Oil filter
Oil filter joint
Oil filter cover
Oil filter cover seal ring
Oil filter cover seal ring
Tube
Oil tube joint I
Oil tube joint |l
Oil tube shape ring
Lubricate bushing
Upper drain pipe
Lower drain pipe
Screw
Oil show bracket
Oil show cleaner link
Oil show cleaner guard
Oil dial
Screw
Screw
Screw

High Speed Overlock Machine | Instructions Manual and Parts List 47

 6.16
Feed Snap
Components

High Speed Overlook Machine | Instructions Manual and Parts List 48

 6.16
F d s 1 Oil seal
ee nap 2 Needle cooler ---
Components Needle cooler ---

4
5
one
Silicon oil box cover (Lower)
---
---
6 Silicon oil box (Lower) ---

9 Cloth guide holder ---

10 Hinge plate ---
11 Oil felt block ---
13 Hinge spring ---
14 Snap plate ---
Snap plate ---
Snap plate ---
15 Snap plate bracket ---

16 screw ---
18 Hinge spring screw ---
19 Hinge screw ---

21
22
Screw
Needle cooler screw
---
---

23 screw ---
25 Oil tube shape ring ---

High Speed Overlock Machine | Instructions Manual and Parts List 49

 6.17
Thread Spool
Components

High Speed Overlook Machine | Instructions Manual and Parts List 50

 6. 17 1 Upper thread column
Thread SPOO’ 2 Lower thread column ---
Components 3 Bushing ---
4 Thread spool tray bracket (lower) ---
5 Thread guide hook ---

8 Spool retainer ---

9 Clamp plate ---
10 Spool tray cushion ---
11 Thread guide connecting bar ---
12 Thread guide joint ---
14 Thread guide bar ---
15 Thread spool tray bracket (upper) ---
16 Thread spool tray bracket (upper) ---
17 Thread spool tray bracket (lower) ---
18 Thread guide hook ---
19 Rubber seal --
20 Thread guide hook screw ---
21 Thread guide hook nut ---
22 Thread guide washer ---
23 Clamp plate screw ---

26 Lower washer ---

High Speed Overlock Machine llnstructions Manual and Parts List 51

 6. 18
Plate Raw
Material
Components

Machine support plate

Support shockproof cushion
Screw
Bolt
Washer
Bolt specer
Waste chute inlet
Waste chute (upper)
Waste chute (lower)
Cushion rubber
Screw
Washer
Screw

High Speed Overlock Machine | Instructions Manual and Parts List 52

 6. 19 H

2i 5
Accessories

36j/M"
Aw
m;
W

M%
K
coooxlmcnhwwa

Dust cover
Oil can
Notes oil
Funnel
Oil can/50cc
Spanner
Spanner
Spanner
Inner-hexagon screw driver
O
_|

Inner-hexagon screw driver

_\
_\

Inner-hexagon screw driver

(A)
_\

Allen Key Driver

.5
_\

Screw driver
_\
O'l

Screw driver
O)
_\

Tweezers
_\
\l

Threader
18 Presser foot base chain
20 Thumb screw
21 Needle
22 Lower knife
Lower knife
23 Oil filter
24 Belt

High Speed Overlock Machine llnstructions Manual and Parts List 53

321 C-132M—01 5 20115006 20116006
321C-131M—04 20115001 20116001
321C-133M—04/TF 20115004 20116004
321C-134M—04 20115001 20116004
321C-241M-24 20115002 20116002
321C-241M-25 20115010 20116008
321C-243M-24/TF 20115005 20116005
321C-244M-24 20115002 20116002
321C-251M-35 20115003 20116003
321C-251M-55 20115008 20116007
321C-251H-56 20115007 20116015

321C-132M-015 20128006 20104009

321C-131M-04 20128006 20104009
321C-133M-04/TF 20128006 20104009
321C-134M—04 20128006 20104009
321C-241M-24 20128005 20104009
321C-241M-25 20128035 20104009
321C-243M-24/TF 20128005 20104009
321C-244M-24 20128005 20104010
321C-251M-35 20128005 20104010
321C-251M-55 20128005 20104010
321C-251H—56 20128005 20104010

High Speed Overlock Machine | Instructions Manual and Parts List 54

 P/N 364336-001
Rev 1 - Ju|.2009

Q} SINGER?
® Singer is a registered trademark of The Singer Company Limited or its affiliated companies.
© 2008 Copyright The Singer Company Limited