PROJECT : PAGE :

CLIENT : DESIGN BY :
JOB NO. : DATE : REVIEW BY :
Wind Analysis for Building with h < 60 ft, Based on 2018 IBC/ASCE 7-16

INPUT DATA
Exposure category (B, C or D, ASCE 7-16 26.7.3) C
Importance factor (ASCE 7-16 Table 1.5-2) Iw = 1.00 for all Category
Basic wind speed (ASCE 7-16 26.5.1 or 2018 IBC) V = 120 mph, (193.12 kph)
Topographic factor (ASCE 7-16 26.8 & Table 26.8-1) Kzt = 1 Flat
Building height to roof H = 60 ft, (18.29 m)
Building length L = 300 ft, (91.44 m)
Building width B = 200 ft, (60.96 m)
Natural frequency (ASCE 7-16 26.11) n1 = 2.5 Hz, (1 / T)
Effective area of components (or Solar Panel area) A = 12 ft2, <== Overhang? (Yes or No) No
( 1.12 m2)

DESIGN SUMMARY
Max building horizontal force normal to building length, L, face = 648.5 kips, (2885 kN), SD/LRFD level, Typ.
Max overturning moment at wind normal to building length, L, face = 93540.6 ft-kips, (126824 kN-m)
Max building horizontal force normal to building length, B, face = 396.3 kips, (1763 kN)
Max overturning moment at wind normal to building length, B, face = 106258.1 ft-kips, (144067 kN-m)
Max building upward force = 1349.3 kips, (6002 kN)
Max building torsion force = 23122.9 ft-kips, (31350 kN-m)

ANALYSIS
Velocity pressures
qz = 0.00256 Kz Kzt Kd Ke V2
where: qz = velocity pressure at height, z. (Eq. 26.10-1, page 268) pmin = 16 psf (ASCE 7-16 27.1.5)
Kz = velocity pressure exposure coefficient evaluated at height, z. (Tab. 26.10-1, page 268)
Kd = wind directionality factor. (Tab. 26.6-1, for building, page 266) = 0.85
z = height above ground
z (ft) 0 - 15 20 25 30 40 50 60 60 60 60 60 60
Kz 0.85 0.90 0.94 0.98 1.04 1.09 1.13 1.13 1.13 1.13 1.13 1.13
qz (psf) 26.63 28.20 29.45 30.71 32.59 34.15 35.41 35.41 35.41 35.41 35.41 35.41

z (ft) 60 60 60 60 60 60 60 60 60 60
Kz 1.13 1.13 1.13 1.13 1.13 1.13 1.13 1.13 1.13 1.13
qz (psf) 35.41 35.41 35.41 35.41 35.41 35.41 35.41 35.41 35.41 35.41

Design pressures for MWFRS

p = q G Cp - qh (G Cpi)
where: p = pressure on surface for rigid building with all h. (Eq. 27.3-1, page 274).
q = qz for windward wall at height z above the ground, see table above.
G Cp i = internal pressure coefficient. (Tab. 26.13-1, Enclosed Building, page 271) = 0.18 or -0.18
qh = qz value at mean roof height, h, for leeward wall, side walls, and roof.
Cp = external pressure coefficient, see right down tables. (Tab. 27.3-1, page 275)
G = gust effect factor (ASCE 7-16 26.11, Page 269)
  1  1.7 I g 2 Q 2  g 2 R 2  Iz =
0.925  z Q R
 , for n1  1.0 0.20 z= 36 Q= 0.84
 

1  1.7 g v I z 
 zmin = 15 gQ = 3.4 Lz = 509
G
  1  1.7 g Q I zQ  = 0.847 c= 0.2 gR = 4.40 b= 0.05
0.925   , for n1  1.0
  1  1.7 g v I z  Rh = 0.154 RB = 0.049 RL = 0.010
N1 = 10.97 Rn = 0.031 R= 0.050

h= 60 gv = 3.4 Vz = 115.9

Fig. 27.3-1 fo q < 10o, page 275

Roof h/B Distance Cp
To L Face 0.30 30 -0.90
To L Face 0.30 60 -0.90
To L Face 0.30 120 -0.50
To L Face 0.30 200 -0.30
Roof h/L Distance Cp
q G Cp Figure for Gable, Hip Roof, page 275 To B Face 0.20 30 -0.90
Fig. 27.3-1, page 275 To B Face 0.20 60 -0.90
Wall Direction L/B Cp To B Face 0.20 120 -0.50
Windward Wall All All 0.80 To B Face 0.20 300 -0.30
Leeward Wall To L Dir 0.67 -0.50
Leeward Wall To B Dir 1.50 -0.40
Side Wall All All -0.70
 (cont'd)
Hence, MWFRS Net Pressures are given by following tables (ASCE 7-16 27.3.1, Page 274)

P (psf) with P (psf) with

Surface z (ft) GCPi - GCPi Surface z (ft) GCPi - GCPi
0 - 15 11.67 24.42 Side Wall All -27.36 -14.62
20 12.73 25.48
25 13.58 26.33
30 14.43 27.18 Normal to L Face P (psf) with Normal to B Face P (psf) with
40 15.70 28.45 Surface z (ft) GCPi - GCPi Surface z (ft) GCPi - GCPi
50 16.77 29.51 Leeward All -21.37 -8.62 Leeward All -18.37 -5.62
60 17.61 30.36

Normal to L Face P (psf) with Normal to B Face P (psf) with

Windward Wall

Surface Dist. (ft) GCPi - GCPi Surface Dist. (ft) GCPi - GCPi
0 - 30 -33.36 -20.61 0 - 30 -33.36 -20.61
60 -33.36 -20.61 60 -33.36 -20.61
Roof Roof
120 -21.37 -8.62 120 -21.37 -8.62
200 -15.37 -2.62 300 -15.37 -2.62

Figure 27.3-8, page 283

Normal to L Face Normal to B Face Wind with Angle
Base Forces ASCE-7
Case 1 Case 2 Case 1 Case 2 Case 3 Case 4
VBase (kips) 648 486 396 297 784 428
MBase (ft - kips) 93541 70155 106258 79694 149849 79701 Fig. 27.4-8
MT (ft - kips) 0 21886 0 8917 0 23123 Page 271
FUpward (kips) 972 729 828 621 1349 719
Vmin (kips) 288 288 192 192 360 346 Min. wind
FUp,min (kips) 960 960 960 960 960 960 27.4.7

Design pressures for components and cladding

p = qh[ (G Cp) - (G Cpi)]
where: p = pressure on component. (Eq. 30.3-1, pg 334)
pmin = 16.00 psf (ASCE 7-16 30.2.2)
G Cp = external pressure coefficient.
see table below. (ASCE 7-16 30.3.2)
o
q= 0.00

Effective Zone 1 Zone 1' Zone 2 Zone 2e Zone 2n Zone 2r

Area (ft2) GCP - GCP GCP - GCP GCP - GCP GCP - GCP GCP - GCP GCP - GCP
12 0.29 -1.67 0.29 -0.90 0.29 -2.26 - - - - - -
Comp.
Effective Zone 3 Zone 3e Zone 3r Zone 4 Zone 5
Area (ft2) GCP - GCP GCP - GCP GCP - GCP GCP - GCP GCP - GCP
12 0.29 -3.12 - - - - 0.89 -0.98 0.89 -1.23

Zone 1 Zone 1' Zone 2 Zone 2e Zone 2n Zone 2r

Comp. & Cladding Positive Negative Positive Negative Positive Negative Positive Negative Positive Negative Positive Negative
Pressure 16.72 -65.41 16.72 -38.24 16.72 -86.33
( psf ) Zone 3 Zone 3e Zone 3r Zone 4 Zone 5
Positive Negative Positive Negative Positive Negative Positive Negative Positive Negative (The Max Pressure
16.72 -116.71 37.80 -40.98 37.80 -50.10 116.71 psf)
 PROJECT : PAGE :
CLIENT : DESIGN BY :
JOB NO. : DATE : REVIEW BY :
Wind Analysis for Low-rise Building, Based on 2018 IBC/ASCE 7-16

INPUT DATA
Exposure category (B, C or D, ASCE 7-16 26.7.3) C
Importance factor (ASCE 7-16 Table 1.5-2) Iw = 1.00 for all Category
Basic wind speed (ASCE 7-16 26.5.1 or 2018 IBC) V = 120 mph, (193.12 kph)
Topographic factor (ASCE 7-16 26.8 & Table 26.8-1) Kzt = 1 Flat
Building height to eave he = 60 ft, (18.29 m)
Building height to ridge hr = 60.001 ft, (18.29 m)
Building length L = 300 ft, (91.44 m)
Building width B = 200 ft, (60.96 m)
Effective area of components (or Solar Panel area) A = 12 ft2, <== Overhang? (Yes or No) No
( 1.12 m2)

DESIGN SUMMARY
Max horizontal force normal to building length, L, face = 469.51 kips, (2088 kN), SD level (LRFD level), Typ.
Max horizontal force normal to building length, B, face = 322.92 kips, (1436 kN)
Max total horizontal torsional load = 17847.31 ft-kips, (24198 kN-m)
Max total upward force = 1584.86 kips, (7050 kN)

ANALYSIS
Velocity pressure
qh = 0.00256 Kz Kzt Kd Ke V2 = 35.41 psf
where: qh = velocity pressure at mean roof height, h. (Eq. 26.10-1 page 268)
Kz = velocity pressure exposure coefficient evaluated at height, h, (Tab. 26.10-1, pg 268) = 1.13
Kd = wind directionality factor. (Tab. 26.6-1, for building, page 266) = 0.85
h = mean roof height = 60.00 ft
Ke = ground elevation factor. (1.0 per Sec. 26.9, page 268) > 60 ft, [Unsatisfactory] (ASCE 7-16 26.2.1)
< Min (L, B), [Satisfactory] (ASCE 7-16 26.2.2)
Design pressures for MWFRS
p = qh [(G Cpf )-(G Cpi )]
where: p = pressure in appropriate zone. (Eq. 28.3-1, page 311). pmin = 16 psf (ASCE 7-16 28.3.4)
G Cp f = product of gust effect factor and external pressure coefficient, see table below. (Fig. 28.3-1, page 312 & 313)
G Cp i = product of gust effect factor and internal pressure coefficient.(Tab. 26.13-1, Enclosed Building, page 271)
= 0.18 or -0.18
a = width of edge strips, Fig 28.3-1, page 312, MAX[ MIN(0.1B, 0.1L, 0.4h), MIN(0.04B, 0.04L), 3] = 20.00 ft

Net Pressures (psf), Basic Load Cases Net Pressures (psf), Torsional Load Cases
Roof angle q = 0.00 Roof angle q = 0.00 Roof angle q = 0.00
Surface Net Pressure with Net Pressure with Surface Net Pressure with
G Cp f G Cp f G Cp f
(+GCp i ) (-GCp i ) (+GCp i ) (-GCp i ) (+GCp i ) (-GCp i )
1 0.40 7.79 20.54 -0.45 -22.31 -9.56 1T 0.40 1.95 5.13
2 -0.69 -30.80 -18.06 -0.69 -30.80 -18.06 2T -0.69 -7.70 -4.51
3 -0.37 -19.47 -6.73 -0.37 -19.47 -6.73 3T -0.37 -4.87 -1.68
4 -0.29 -16.64 -3.89 -0.45 -22.31 -9.56 4T -0.29 -4.16 -0.97
5 0.40 7.79 20.54 Roof angle q = 0.00
6 -0.29 -16.64 -3.89 Surface Net Pressure with
G Cp f
1E 0.61 15.23 27.97 -0.48 -23.37 -10.62 (+GCp i ) (-GCp i )
2E -1.07 -44.26 -31.51 -1.07 -44.26 -31.51 5T 0.40 1.95 5.13
3E -0.53 -25.14 -12.39 -0.53 -25.14 -12.39 6T -0.29 -4.16 -0.97
4E -0.43 -21.60 -8.85 -0.48 -23.37 -10.62
5E 0.61 15.23 27.97
6E -0.43 -21.60 -8.85
Basic Load Case A (Transverse Direction) Basic Load Case B (Longitudinal Direction)
Area Pressure (k) with Area Pressure (k) with
Surface Surface
(ft2) (+GCp i ) (-GCp i ) (ft2) (+GCp i ) (-GCp i )
1 15600 121.52 320.37 2 26000 -800.93 -469.51
2 26000 -800.93 -469.51 3 26000 -506.33 -174.92
3 26000 -506.33 -174.92 5 9600 74.78 197.15
4 15600 -259.61 -60.76 6 9600 -159.76 -37.39
1E 2400 36.54 67.13 2E 4000 -177.04 -126.05
2E 4000 -177.04 -126.05 3E 4000 -100.56 -49.57
3E 4000 -100.56 -49.57 5E 2400 36.54 67.13
4E 2400 -51.84 -21.24 6E 2400 -51.84 -21.24
Horiz. 469.51 469.51 Horiz. 322.92 322.92
S S
Vert. -1584.86 -820.05 Vert. -1322.56 -598.54
Min. wind Horiz. 288.00 288.00 Min. wind Horiz. 192.00 192.00
28.4.4 Vert. -960.00 -960.00 28.4.4 Vert. -960.00 -960.00

Torsional Load Case A (Transverse Direction) Torsional Load Case B (Longitudinal Direction)
Area Pressure (k) with Torsion (ft-k) Area Pressure (k) with Torsion (ft-k)
Surface Surface
(ft2) (+GCp i ) (-GCp i ) (+GCp i ) (-GCp i ) (ft2) (+GCp i ) (-GCp i ) (+GCp i ) (-GCp i )
1 6600 51.41 135.54 3342 8810 2 26000 -800.93 -469.51 0 0
2 11000 -338.85 -198.64 0 0 3 26000 -506.33 -174.92 0 0
3 11000 -214.22 -74.00 0 0 5 3600 28.04 73.93 1122 2957
4 6600 -109.84 -25.71 7139 1671 6 3600 -59.91 -14.02 2396 561
1E 2400 36.54 67.13 4750 8727 2E 4000 -177.04 -126.05 0 0
2E 4000 -177.04 -126.05 0 0 3E 4000 -100.56 -49.57 0 0
3E 4000 -100.56 -49.57 0 0 5E 2400 36.54 67.13 3289 6042
4E 2400 -51.84 -21.24 6739 2762 6E 2400 -51.84 -21.24 4665 1912
1T 9000 17.53 46.21 -1315 -3466 5T 6000 11.68 30.81 -584 -1540
2T 15000 -115.52 -67.72 0 0 6T 6000 -24.96 -5.84 -1248 -292
3T 15000 -73.03 -25.23 0 0 Total Horiz. Torsional Load, MT 9639.9 9639.9
4T 9000 -37.44 -8.76 -2808 -657
Total Horiz. Torsional Load, MT 17847 17847
 PROJECT : PAGE :
CLIENT : DESIGN BY :
JOB NO. : DATE : REVIEW BY :
Wind Analysis for Low-rise Building, Based on ASCE 7-2010

INPUT DATA
Exposure category (B, C or D, ASCE 7-10 26.7.3) #REF! #REF!
Importance factor (ASCE 7-10 Table 1.5-2) Iw = 1.00 for all Category
Basic wind speed (ASCE 7-10 26.5.1 or 2012 IBC) V = #REF! mph
Topographic factor (ASCE 7-10 26.8 & Table 26.8-1) Kzt = #REF! #REF!
Building height to eave he = #REF! ft
Building height to ridge hr = #REF! ft
Building length L = #REF! ft
Building width B = #REF! ft
Effective area of components (or Solar Panel area) A = #REF! ft2

DESIGN SUMMARY
Max horizontal force normal to building length, L, face = #REF! kips, SD level (LRFD level), Typ.
Max horizontal force normal to building length, B, face = #REF! kips
Max total horizontal torsional load = #REF! ft-kips
Max total upward force = #REF! kips

ANALYSIS
Velocity pressure
qh = 0.00256 Kh Kzt Kd V2 = #REF! psf
where: qh = velocity pressure at mean roof height, h. (Eq. 28.3-1 page 298 & Eq. 30.3-1 page 316)
Kh = velocity pressure exposure coefficient evaluated at height, h, (Tab. 28.3-1, pg 299) = #REF!
Kd = wind directionality factor. (Tab. 26.6-1, for building, page 250) = #REF!
h = mean roof height = #REF! ft
#REF! (ASCE 7-10 26.2.1)
#REF! (ASCE 7-10 26.2.2)
Design pressures for MWFRS
p = qh [(G Cpf )-(G Cpi )]
where: p = pressure in appropriate zone. (Eq. 28.4-1, page 298). pmin = 16 psf (ASCE 7-10 28.4.4)
G Cp f = product of gust effect factor and external pressure coefficient, see table below. (Fig. 28.4-1, page 300 & 301)
G Cp i = product of gust effect factor and internal pressure coefficient.(Tab. 26.11-1, Enclosed Building, page 258)
= #REF! or #REF!
a = width of edge strips, Fig 28.4-1, note 9, page 301, MAX[ MIN(0.1B, 0.1L, 0.4h), MIN(0.04B, 0.04L), 3] = #REF! ft

Net Pressures (psf), Basic Load Cases Net Pressures (psf), Torsional Load Cases
Roof angle q = #REF! Roof angle q = 0.00 Roof angle q = #REF!
Surface Net Pressure with Net Pressure with Surface Net Pressure with
G Cp f G Cp f G Cp f
(+GCp i ) (-GCp i ) (+GCp i ) (-GCp i ) (+GCp i ) (-GCp i )
1 #REF! #REF! #REF! -0.45 #REF! #REF! 1T #REF! #REF! #REF!
2 #REF! #REF! #REF! -0.69 #REF! #REF! 2T #REF! #REF! #REF!
3 #REF! #REF! #REF! -0.37 #REF! #REF! 3T #REF! #REF! #REF!
4 #REF! #REF! #REF! -0.45 #REF! #REF! 4T #REF! #REF! #REF!
5 0.40 #REF! #REF! Roof angle q = 0.00
6 -0.29 #REF! #REF! Surface Net Pressure with
G Cp f
1E #REF! #REF! #REF! -0.48 #REF! #REF! (+GCp i ) (-GCp i )
2E #REF! #REF! #REF! -1.07 #REF! #REF! 5T 0.40 #REF! #REF!
3E #REF! #REF! #REF! -0.53 #REF! #REF! 6T -0.29 #REF! #REF!
4E #REF! #REF! #REF! -0.48 #REF! #REF!
5E 0.61 #REF! #REF!
6E -0.43 #REF! #REF!
Basic Load Case A (Transverse Direction) Basic Load Case B (Longitudinal Direction)
Area Pressure (k) with Area Pressure (k) with
Surface Surface
(ft2) (+GCp i ) (-GCp i ) (ft2) (+GCp i ) (-GCp i )
1 #REF! #REF! #REF! 2 #REF! #REF! #REF!
2 #REF! #REF! #REF! 3 #REF! #REF! #REF!
3 #REF! #REF! #REF! 5 #REF! #REF! #REF!
4 #REF! #REF! #REF! 6 #REF! #REF! #REF!
1E #REF! #REF! #REF! 2E #REF! #REF! #REF!
2E #REF! #REF! #REF! 3E #REF! #REF! #REF!
3E #REF! #REF! #REF! 5E #REF! #REF! #REF!
4E #REF! #REF! #REF! 6E #REF! #REF! #REF!
Horiz. #REF! #REF! Horiz. #REF! #REF!
S S
Vert. #REF! #REF! Vert. #REF! #REF!
Min. wind Horiz. #REF! #REF! Min. wind Horiz. #REF! #REF!
28.4.4 Vert. #REF! #REF! 28.4.4 Vert. #REF! #REF!

Torsional Load Case A (Transverse Direction) Torsional Load Case B (Longitudinal Direction)
Area Pressure (k) with Torsion (ft-k) Area Pressure (k) with Torsion (ft-k)
Surface Surface
(ft2) (+GCp i ) (-GCp i ) (+GCp i ) (-GCp i ) (+GCp i ) (-GCp i ) (+GCp i ) (-GCp i )
(ft2)
1 #REF! #REF! #REF! #REF! #REF! 2 #REF! #REF! #REF! #REF! #REF!
2 #REF! #REF! #REF! #REF! #REF! 3 #REF! #REF! #REF! #REF! #REF!
3 #REF! #REF! #REF! #REF! #REF! 5 #REF! #REF! #REF! #REF! #REF!
4 #REF! #REF! #REF! #REF! #REF! 6 #REF! #REF! #REF! #REF! #REF!
1E #REF! #REF! #REF! #REF! #REF! 2E #REF! #REF! #REF! #REF! #REF!
2E #REF! #REF! #REF! #REF! #REF! 3E #REF! #REF! #REF! #REF! #REF!
3E #REF! #REF! #REF! #REF! #REF! 5E #REF! #REF! #REF! #REF! #REF!
4E #REF! #REF! #REF! #REF! #REF! 6E #REF! #REF! #REF! #REF! #REF!
1T #REF! #REF! #REF! #REF! #REF! 5T #REF! #REF! #REF! #REF! #REF!
2T #REF! #REF! #REF! #REF! #REF! 6T #REF! #REF! #REF! #REF! #REF!
3T #REF! #REF! #REF! #REF! #REF! Total Horiz. Torsional Load, MT #REF! #REF!
4T #REF! #REF! #REF! #REF! #REF!
Total Horiz. Torsional Load, MT #REF! #REF!

Design pressures for components and cladding

p = qh[ (G Cp) - (G Cpi)]
where: p = pressure on component. (Eq. 30.4-1, pg 318)
pmin = 16.00 psf (ASCE 7-10 30.2.2)
G Cp = external pressure coefficient.
see table below. (ASCE 7-10 30.4.2)

Effective Zone 1 Zone 2 Zone 3 Zone 4 Zone 5

Area (ft2) GCP - GCP GCP - GCP GCP - GCP GCP - GCP GCP - GCP
Comp. #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF!

Comp. & Cladding Zone 1 Zone 2 Zone 3 Zone 4 Zone 5

Pressure Positive Negative Positive Negative Positive Negative Positive Negative Positive Negative
( psf ) #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!

Note: If the effective area is roof Solar Panel area, the only zone 1, 2 , or 3 apply.
 PROJECT : PAGE :
CLIENT : DESIGN BY :
JOB NO. : DATE : REVIEW BY :
Wind Analysis for Building with h > 60 ft, Based on ASCE 7-2010

INPUT DATA
Exposure category (B, C or D, ASCE 7-10 26.7.3) #REF! #REF!
Importance factor (ASCE 7-10 Table 1.5-2) Iw =
1.00 for all Category
Basic wind speed (ASCE 7-10 26.5.1 or 2012 IBC) V = #REF! mph
Topographic factor (ASCE 7-10 26.8 & Table 26.8-1) Kzt = #REF! #REF!
Building height to roof H = #REF! ft
Parapet height HP = 0 #REF!
Building length L = #REF! ft
Building width B = #REF! ft
Natural frequency (ASCE 7-10 26.9) n1 = #REF! Hz, (1 / T)
Effective area of mullion AM = #REF! ft2
Effective area of panel AP = #REF! ft2

DESIGN SUMMARY
Max building horizontal force normal to building length, L, face = #REF! kips, SD level (LRFD level), Typ.
Max overturning moment at wind normal to building length, L, face = #REF! ft - kips
Max building horizontal force normal to building length, B, face = #REF! kips
Max overturning moment at wind normal to building length, B, face = #REF! ft - kips
Max building upward force = #REF! kips
Max building torsion force = #REF! ft - kips

ANALYSIS
Velocity pressures
qz = 0.00256 Kz Kzt Kd V2
where: qz = velocity pressure at height, z. (Eq. 27.3-1, page 260 & Eq. 30.3-1 page 316) pmin = 16 psf (ASCE 7-10 27.4.7)
Kz = velocity pressure exposure coefficient evaluated at height, z. (Tab. 27.3-1, page 261)
Kd = wind directionality factor. (Tab. 26.6-1, for building, page 250) = 0.85
z = height above ground
z (ft) #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
Kz #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
qz (psf) #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!

z (ft) #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
Kz #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
qz (psf) #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!

Design pressures for MWFRS

p = q G Cp - qh (G Cpi)
where: p = pressure on surface for rigid building with all h. (Eq. 27.4-1, page 260).
q = qz for windward wall at height z above the ground, see table above.
G Cp i = internal pressure coefficient. (Tab. 26.11-1, Enclosed Building, page 258) = 0.18 or -0.18
qh = qz value at mean roof height, h, for leeward wall, side walls, and roof.
Cp = external pressure coefficient, see right down tables. (Tab. 27.4-1, page 263)
G = gust effect factor (ASCE 7-10 26.9, Page 254)
  1  1.7 I g 2 Q 2  g 2 R 2  Iz = #REF! z= #REF! Q= #REF!
0.925  z Q R  , for n1  1.0
  1  1.7 g v I z  zmin = #REF! gQ = 3.4 Lz = #REF!
G  
 = #REF! c= #REF! gR = #REF! b= 0.05
 1  1.7 g Q I zQ 
0.925   , for n1  1.0 Rh = RB = RL =
  1  1.7 g v I z  #REF! #REF! #REF!
N1 = #REF! Rn = #REF! R= #REF!

h= #REF! gv = 3.4 Vz = #REF!

Fig. 27.4-1 fo q < 10o, page 263

Roof h/B Distance Cp
To L Face #REF! #REF! #REF!
To L Face #REF! #REF! #REF!
To L Face #REF! #REF! #REF!
To L Face #REF! #REF! #REF!
Roof h/L Distance Cp
q G Cp Figure for Gable, Hip Roof, page 48 To B Face #REF! #REF! #REF!
Fig. 27.4-1, page 263 To B Face #REF! #REF! #REF!
Wall Direction L/B Cp To B Face #REF! #REF! #REF!
Windward Wall All All 0.80 To B Face #REF! #REF! #REF!
Leeward Wall To L Dir #REF! #REF!
Leeward Wall To B Dir #REF! #REF!
Side Wall All All -0.70
 (cont'd)
Hence, MWFRS Net Pressures are given by following tables (ASCE 7-10 27.4.1, Page 260)

P (psf) with P (psf) with

Surface z (ft) GCPi - GCPi Surface z (ft) GCPi - GCPi
#REF! #REF! #REF! Side Wall All #REF! #REF!
#REF! #REF! #REF!
#REF! #REF! #REF!
#REF! #REF! #REF! Normal to L Face P (psf) with Normal to B Face P (psf) with
#REF! #REF! #REF! Surface z (ft) GCPi - GCPi Surface z (ft) GCPi - GCPi
#REF! #REF! #REF! Leeward All #REF! #REF! Leeward All #REF! #REF!
#REF! #REF! #REF!
#REF! #REF! #REF!
#REF! #REF! #REF! Normal to L Face P (psf) with Normal to B Face P (psf) with
Windward Wall

#REF! #REF! #REF! Surface Dist. (ft) GCPi - GCPi Surface Dist. (ft) GCPi - GCPi
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
Roof Roof
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF!
#REF! #REF! #REF!
#REF! #REF! #REF!
#REF! #REF! #REF!
#REF! #REF! #REF!
#REF! #REF! #REF!
#REF! #REF! #REF!
#REF! #REF! #REF!
Figure 27.4-8, page 271
Normal to L Face Normal to B Face Wind with Angle
Base Forces ASCE-7
Case 1 Case 2 Case 1 Case 2 Case 3 Case 4
VBase (kips) #REF! #REF! #REF! #REF! #REF! #REF!
MBase (ft - kips) #REF! #REF! #REF! #REF! #REF! #REF! Fig. 27.4-8
MT (ft - kips) 0 #REF! 0 #REF! 0 #REF! Page 271
FUpward (kips) #REF! #REF! #REF! #REF! #REF! #REF!
Vmin (kips) #REF! #REF! #REF! #REF! #REF! #REF! Min. wind
FUp,min (kips) #REF! #REF! #REF! #REF! #REF! #REF! 27.4.7

Design pressures for components and cladding

p = q (G Cp) - qi (G Cpi)
where: p = pressure on component for building with h > 60 ft. (Eq. 30.6-1, page 320)
pmin = 16.00 psf (ASCE 7-10 30.2.2)
q = qz for windward wall at height z above the ground, see table above.
qh = qz value at mean roof height, h, for leeward wall, side walls, and roof.
G Cp i = internal pressure coefficient. (Tab. 26.11-1, pg 258) =
0.18 or -0.18
a = Zone width = MAX[ MIN(0.1B, 0.1L), 3] = #REF! ft, (Fig 30.6-1 note 8, pg 348)
G Cp = external pressure coefficient. (Fig 30.6-1 note 8, pg 348)
Wall Actual Effective Zone 4 Zone 5
Comp. Area ( ft2 ) GCP - GCP GCP - GCP
Mullion #REF! #REF! #REF! #REF! #REF!
Panel #REF! #REF! #REF! #REF! #REF!

Mullion Pressure (psf) Panel Pressure (psf)

z (ft) Zone 4 Zone 5 Zone 4 Zone 5
Positive Negative Positive Negative Positive Negative Positive Negative
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF! #REF!
 cont'd
Effective Zone 1 Zone 2 Zone 3
Roof
Area ( ft2 ) - GCP - GCP - GCP
0 -1.40 -2.30 -3.20
10 -1.40 -2.30 -3.20
#REF! #REF! #REF! #REF!

Components and Cladding

#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF!
Effective Net Pressure (psf)
Roof
Area ( ft2 ) Zone 1 Zone 2 Zone 3
0 #REF! #REF! #REF!
10 #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
Components and Cladding

#REF! #REF! #REF! #REF!

#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!
#REF! #REF! #REF! #REF!