DG1000Z Series

Function/Arbitrary
Waveform Generator

SiFi (Signal Fidelity) for 100% waveform replication

2Mpts or 8Mpts/CH(std.), 16Mpts/CH (opt.) arbitrary waveform length
Standard 2 full functional independent channels
±1ppm frequency stability, -125dBc/Hz phase noise, 200ps low jitter
Built-in 8 orders harmonics generator
Built-in 7 digits/s counter up to 200MHz
160 built-in pre-edited waveforms
Intuitive arbitrary waveform editing software
Full modulation supported: AM, FM, PM, ASK, FSK, PSK and PWM

DG1000Z series function/arbitrary waveform generator is a multi-

functional generator that combines many functions in one, including
Function Generator, Arbitrary Waveform Generator, Noise Generator,
Pulse Generator, Harmonics Generator, Analog/Digital Modulator and
Counter. As a multi-functional, high performance and portable generator,
it will be a new selection in education, R&D, production, test and etc.

RIGOL TECHNOLOGIES, INC.

DG1000Z Series Function/Arbitrary Waveform Generator

Dimensions: Width×Height×Depth=261.5mm×112mm×318.4mm
Weight: 3.2kg (without package)

1 RIGOL
 Feature and Benefits

Standard 2 full functional channels Arbitrary waveform function with Up to 160 built-in waveforms
innovative SiFi technology

Burst function Multiple analog and digital modulations Sweep function

Standard harmonic generator Waveform summing function Standard 7 digits/s full function frequency
counter with 200MHz bandwidth

Channels and system setting In line with LXI Core 2011 Device File Management Function

2 RIGOL
 Specifications
All the specifications can be guaranteed if the following two conditions are met unless where noted.
· The generator is within the calibration period and has performed self-calibration.
· The generator has been working continuously for at least 30 minutes under the specified temperature (18℃ ~ 28℃ ).
All the specifications are guaranteed unless those marked with “typical”.

Model DG1022Z DG1032Z DG1062Z

Channel 2 2 2
Max Frequency 25 MHz 30 MHz 60 MHz
Sample Rate 200 MSa/s

Waveform
Basic Waveform Sine, Square, Ramp, Pulse, Noise
160 kinds, including Sinc, Exponential Rise, Exponential Fall, ECG, Gauss, HaverSine, Lorentz,
Built-in Arbitrary Waveform
Dual-Tone, etc.

Frequency Characteristics
Sine 1 μHz to 25 MHz 1 μHz to 30 MHz 1 μHz to 60 MHz
Square 1 μHz to 25 MHz 1 μHz to 25 MHz 1 μHz to 25 MHz
Ramp 1 μHz to 500 kHz 1 μHz to 500 kHz 1 μHz to 1 MHz
Pulse 1 μHz to 15 MHz 1 μHz to 15 MHz 1 μHz to 25 MHz
Harmonic 1uHz to 10 MHz 1 μHz to 10 MHz 1uHz to 20 MHz
Noise (-3dB) 25 MHz bandwidth 30 MHz bandwidth 60 MHz bandwidth
Arbitrary Waveform 1 μHz to 10 MHz 1 μHz to 10 MHz 1 μHz to 20 MHz
Resolution 1 μHz
Accuracy ±1 ppm of the setting value, 18℃ to 28℃

Sine Wave Spectrum Purity

Typical (0 dBm)
DC-10 MHz (included): <-65 dBc
Harmonic Distortion
10 MHz to 30 MHz (included): <-55 dBc
30 MHz to 60 MHz (included): <-50 dBc
Total Harmonic Distortion <0.075% (10 Hz to 20 kHz, 0 dBm)
Typical (0 dBm)
Spurious (non-harmonic) ≤10 MHz: <-70 dBc
>10 MHz: <-70 dBc + 6 dB/octave
Typical (0 dBm, 10 kHz offset)
Phase Noise
10 MHz: <-125 dBc/Hz

Signal Characteristics
Square
Typical (1 Vpp)
Rise/Fall Time
<10ns
Typical (100 kHz, 1 Vpp)
Overshoot
≤5%
Duty Cycle 0.01% to 99.99% (limited by the current frequency setting)
Non-symmetry 1% of the period + 5 ns
Typical (1 Vpp)
Jitter (rms) ≤5 MHz: 2 ppm + 200 ps
> 5 MHz: 200 ps
Ramp
Linearity ≤1% of peak output (typical, 1 kHz, 1 VPP, 100% symmetry)
Symmetry 0% to 100%
Pulse
Pulse Width 16ns to 999.999 982 118ks (limited by the current frequency setting)
Duty Cycle 0.001% to 99.999% (limited by the current frequency setting)
Rising/Falling Edge ≥10 ns (limited by the current frequency setting and pulse width setting)
Typical (1 Vpp)
Overshoot
≤5%
Typical (1 Vpp)
Jitter (rms) ≤5 MHz 2 ppm + 200 ps
> 5 MHz 200 ps
Arbitrary Waveform
2Mpts (std.) 8Mpts (std.) 8Mpts (std.)
Waveform Length
16Mpts (opt.) 16Mpts (opt.) 16Mpts (opt.)

3 RIGOL
Vertical Resolution 14 bits
Sample Rate 200MSa/s
Typical (1 Vpp)
Min Rise/Fall Time
<10 ns
Typical (1 Vpp)
Jitter (rms) ≤5 MHz: 2 ppm + 200 ps
> 5 MHz: 200 ps
Editing Mode Point Edit, Block Edit, Insert Waveform
Harmonic Output
Harmonic Order ≤8
Harmonic Type Even Harmonic, Odd harmonic, Order Harmonic, User
Harmonic Amplitude The amplitude of each order of harmonic can be set
Harmonic Phase The phase of each order of harmonic can be set

Output Characteristics
Amplitude (into 50 Ω)
≤10 MHz: 1.0 mVpp to 10 Vpp
Range ≤30 MHz: 1.0 mVpp to 5.0 Vpp
≤60 MHz: 1.0 mVpp to 2.5 Vpp
Typical (1 kHz sine, 0 V offset, >10 mVpp, auto)
Accuracy
±(1% of the setting value) ±1 mV
Typical (sine, 2.5 Vpp)
Flatness ≤10 MHz: ±0.1 dB
≤60 MHz: ±0.2 dB
Unit Vpp, Vrms, dBm
Resolution 0.1mVpp or 4 digits
Offset (into 50 Ω)
Range (Peak ac+dc) ±5Vpk ac+dc
Accuracy ±(1% of the setting value + 5mV + 0.5% of the amplitude)
Waveform Output
Output Impedance 50 Ω (typical)
Protection Short-circuit protection, automatically disable the waveform output when overload occurs

Modulation Characteristics
Modulation Type AM, FM, PM, ASK, FSK, PSK, PWM
AM
Carrier Waveform Sine, Square, Ramp, Arb (except DC)
Source Internal/External
Modulating Waveform Sine, Square, Ramp, Noise, Arb
Modulation Depth 0% to 120%
Modulating Frequency 2 mHz to 1 MHz
FM
Carrier Waveform Sine, Square, Ramp, Arb (except DC)
Source Internal/External
Modulating Waveform Sine, Square, Ramp, Noise, Arb
Modulating Frequency 2 mHz to 1 MHz
PM
Carrier Waveform Sine, Square, Ramp, Arb (except DC)
Source Internal/External
Modulating Waveform Sine, Square, Ramp, Noise, Arb
Phase Deviation 0° to 360°
Modulating Frequency 2 mHz to 1 MHz
ASK
Carrier Waveform Sine, Square, Ramp, Arb (except DC)
Source Internal/External
Modulating Waveform Square with 50% duty cycle
Key Frequency 2 mHz to 1 MHz
FSK
Carrier Waveform Sine, Square, Ramp, Arb (except DC)
Source Internal/External
Modulating Waveform Square with 50% duty cycle
Key Frequency 2 mHz to 1 MHz
PSK
Carrier Waveform Sine, Square, Ramp, Arb (except DC)
Source Internal/External

4 RIGOL
Modulating Waveform Square with 50% duty cycle
Key Frequency 2 mHz to 1 MHz
PWM
Carrier Waveform Pulse
Source Internal/External
Modulating Waveform Sine, Square, Ramp, Noise, Arb
Width Deviation 0% to 100% of the pulse width
Modulating Frequency 2 mHz to 1 MHz
External Modulation Input
Input Range 75 mVRMS to ±5 Vac + dc
Input Bandwidth 50 kHz
Input Impedance 10KΩ

Burst Characteristics
Carrier Waveform Sine, Square, Ramp, Pulse, Noise, Arb (except DC)
Carrier Frequency 2mHz to 25MHz 2mHz to 30MHz 2 mHz to 60 MHz
Burst Count 1 to 1,000,000 or Infinite
Start/Stop Phase 0° to 360°, 0.1° resolution
Internal Period 1 μs to 500 s
Gated Source External Trigger
Trigger Source Internal, External or Manual
Trigger Delay 0 ns to 100 s

Sweep Characteristics
Carrier Waveform Sine, Square, Ramp, Arb (except DC)
Type Linear, Log or Step
Direction Up or Down
Start/Stop Frequency The same with the upper/lower limit of the corresponding carrier frequency
Sweep Time 1 ms to 500 s
Hold/Return Time 0 ms to 500 s
Trigger Source Internal, External or Manual
Marker Falling edge of the sync signal (programmable)

Frequency Counter
Function Frequency, Period, Positive/Negative Pulse Width, Duty Cycle
Frequency Resolution 7 digits/second (Gate Time = 1s)
Frequency Range 1 μHz to 200 MHz
Period Measurement Measurement Range 5ns to 16 days
Voltage Range and Sensitivity (non-modulating signal)
DC Offset Range ±1.5 Vdc
DC Coupling 1μHz to 100 MHz 50 mVRMS to ±2.5 Vac + dc
100 MHz to 200 MHz 100 mVRMS to ±2.5 Vac + dc
1 μHz to 100 MHz 50 mVRMS to ±2.5 Vpp
AC Coupling
100 MHz to 200 MHz 100 mVRMS to ±2.5 Vpp
Pulse Width and Duty Cycle Measurement
Frequency and Amplitude
1 μHz to 25 MHz 50 mVRMS to ±2.5 Vac + dc
Ranges
Min Pulse Width ≥20 ns DC Coupling
Pulse Width
Pulse Width Resolution 5 ns
Duty Cycle Measurement Range (display) 0% to 100%
Input Characteristics
Input Signal Range Breakdown Voltage ±7Vac+dc Input Impedance = 1 MΩ
Coupling Mode AC DC
Input Adjustment On: Input Bandwidth = 250 kHz;
High-frequency Rejection
Off: Input Bandwidth = 200 MHz
Trigger Level Range -2.5V to +2.5V
Input Trigger 0% (about 140 mV hysteresis voltage) to 100% (about 2 mV
Trigger Sensitivity Range
hysteresis voltage)
GateTime1 1.310ms
GateTime2 10.48ms
GateTime3 166.7ms
Gate Time
GateTime4 1.342s
GateTime5 10.73s
GataTime6 >10s

5 RIGOL
Trigger Characteristics
Trigger Input
Level TTL-compatible
Slope Rising or falling (selectable)
Pulse Width >100ns
Sweep: <100 ns (typical)
Latency
Burst: <300 ns (typical)
Trigger Output
Level TTL-compatible
Pulse Width > 60 ns (typical)
Maximum Frequency 1 MHz

Two-channel Characteristics - Phase Offset

Range 0° to 360°
Waveform Phase Resolution 0.03°

Reference Clock
External Reference Input
Lock Range 10 MHz ± 50 Hz
Level 250 mVpp to 5 Vpp
Lock Time <2s
Input Impedance (Typical) 1 kΩ, AC coupling
Internal Reference Output
Frequency 10 MHz ± 50 Hz
Level 3.3 Vpp
Input Impedance (Typical) 50 Ω, AC coupling

Sync Output
Level TTL-compatible
Impedance 50 Ω, nominal value

Overvoltage Protection
Occurred when:
 The instrument amplitude setting is greater than 2Vpp or the output offset is greater than |2VDC| and the input voltage is greater
than ±11.5 × (1 ± 5%)V (<10kHz).
 The instrument amplitude setting is lower than or equal to 2Vpp or the output offset is lower than or equal to |2VDC| and the
input voltage is greater than ±3.5 × (1 ± 5%)V (<10kHz).

General Specifications
Power Supply
Power Voltage 100 V to 240 V (45 Hz to 440 Hz)
Power Consumption Lower than 40 W
Fuse 250 V, T3.15 A
Display
Type 3.5-inch TFT LCD
Resolution 320 horizontal × RGB × 240 vertical resolution
Color 16 M color
Environment
Operating: 0℃ to 50℃
Temperature Range
Non-operating: -40℃ to 70℃
Cooling Method Fan cooling
Lower than 30℃ : ≤95% relative humidity
Humidity Range 30℃ to 40℃ : ≤75% relative humidity
40℃ to 50℃ : ≤45% relative humidity
Operating: below 3000 meters
Altitude
Non-operating: below 15,000 meters
Mechanical
Dimensions (W×H×D) 261.5 mm × 112 mm × 318.4 mm
Without Package: 3.2 kg
Weight
With Package: 4.5 kg
Interfaces USB Host, USB Device, LAN
IP Protection IP2X
Calibration Interval 1 year recommended calibration interval

6 RIGOL
 Certification Information
in line with EN61326-1:2006
±4.0kV (contact discharge)
IEC 61000-3-2:2000
±4.0kV (air discharge)
3 V/m (80 MHz to 1 GHz)
IEC 61000-4-3:2002 3 V/m (1.4 GHz to 2 GHz)
1 V/m (2.0 GHz to 2.7 GHz)
IEC 61000-4-4:2004 1 kV power lines
0.5kV (Phase to Neutral)
EMC IEC 61000-4-5:2001 0.5kV (Phase to PE)
1 kV (Neutral to PE)
IEC 61000-4-6:2003 3V,0.15MHz-80MHz
Voltage dip:
0 % UT during half cycle
0 % UT during 1 cycle
IEC 61000-4-11:2004
70 % UT during 25 cycles
Short interruption:
0 % UT during 1 cycle
Electrical Safety in line with
USA:UL 61010-1:2012,
Electrical Safety
Canada: CAN/CSA-C22.2 No. 61010-1-2012
EN 61010-1:2010

Ordering Information
Description Order Number
DG1022Z (25MHz, Dual-channel) DG1022Z
DG1032Z (30MHz, Dual-channel) DG1032Z
Model
DG1062Z (60MHz, Dual-channel) DG1062Z
Power Cord -
USB Cable CB-USBA-USBB-FF-150
Standard Accessories BNC Cable CB-BNC-BNC-MM-100
Quick Guide -
Resource CD (including User’s Guide and etc.) -
16Mpts Memory for Arb Arb16M-DG1000Z
Rack Mount Kit (for single instrument) RM-1-DG1000Z
Rack Mount Kit (for dual instruments) RM-2-DG1000Z
Options
40dB Attenuator RA5040K
10W Power Amplifier PA1011
USB-GPIB Converter USB-GPIB

HEADQUARTER EUROPE NORTH AMERICA JAPAN

RIGOL TECHNOLOGIES, INC. RIGOL TECHNOLOGIES GmbH RIGOL TECHNOLOGIES, RIGOL TECHNOLOGIES JAPAN G.K.
No.156,Cai He Village, Lindbergh str. 4 USA INC. MJ BLDG.3F,1-7-4 MINATO,CHUOU-
Sha He Town, 82178 Puchheim 10200 SW Allen Blvd, Suite C KU,TOKYO,JAPAN 〒 104-0043
Chang Ping District, Beijing, Germany Beaverton, OR 97005, USA Tel: 03-6262-8932
102206 P.R.China Tel: 0049- 89/89418950 Toll free: 877-4-RIGOL-1 Fax: 03-6262-8933
Tel:+86-10-80706688 Email: [email protected] Office: 440-232-4488 Email: [email protected]
Fax:+86-10-80720067 Fax: 877-474-4651
Electronic Measurement Email: [email protected]
Instrument service and support
email:[email protected]

RIGOL® is the registered trademark of RIGOL Technologies, Inc. Product information in

this document subject to update without notice. For the latest information about RIGOL's
products, applications and services, please contact local RIGOL office or access RIGOL
official website: www.rigol.com

Oct.2016