Scribd
Upload
71 views2 pages

Series PQ-F00 Characteristics: Power Amplifier For Pumps

This document summarizes a power amplifier module used to control the continuous flow adjustment of axial piston pumps. The amplifier allows flow current to be set by an external command signal and internal limits. It features closed-loop feedback control, adjustable gain and ramping, minimum and maximum settings to maintain the working range, and diagnostics. The module housing installs on a DIN rail and has disconnectable screw terminals.

Uploaded by

pawa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
71 views2 pages

Series PQ-F00 Characteristics: Power Amplifier For Pumps

This document summarizes a power amplifier module used to control the continuous flow adjustment of axial piston pumps. The amplifier allows flow current to be set by an external command signal and internal limits. It features closed-loop feedback control, adjustable gain and ramping, minimum and maximum settings to maintain the working range, and diagnostics. The module housing installs on a DIN rail and has disconnectable screw terminals.

Uploaded by

pawa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Power Amplifier for Pumps

Characteristics Series PQ-F00 I-2.1


Application
Electronic module for control of a continuous volume flow
adjustment with position transducer in axial piston pumps
of the PV series.
Flow current can be given by an externally supplied com-
mand signal and internal limitation and ramp potentiom-
eters. In this case, the command signals can be gener-
ated for example by a PLC.

Technical features
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
• Flow current adjustment in closed loop control by feed-
back of the pivoting angle setting
Q
• Differential input stages for voltage or current sig- MIN GAIN

nals MAX

• Ramp generators
RAMPä RAMP

ä
• Min/max adjustment for maintaining the working range
POWER
to the command value range 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
• Dither generator for improving static characteristic
data Characteristic data
• Adjustable control gain
• Diagnosis LED for indicating undervoltage or posi- Supply voltage range 22...36VDC
Supply voltage ripple max. 5%
tion transducer cable breakage
Current consumption max. 1.8A
• Module housing for snap-on assembly on support rail Input signal range
as per EN 50022 Input voltage 0...10V / 100KOhm
Input current 0...20mA / 500Ohm
• Disconnectable terminals
Reference output 0...10V +1% / max. 30mA
Output current max. 1.3A
Adjustment range ramp time 0...5sec.
Ambient temperature range -40...+70°C
Connection Screw-in terminals, plug-
in type AWG 24...13
Installation cross sections min. Voltage supply + sole-
noid: 1.5mm². Other
connections: 0.5mm²
Cable length max. 50m
Pre-fuse 4.0A, medium-lag,
DIN 41571

Ordering code

PQ F 00

Pump Pump design Version Design


amplifier code status

Pump design
Code Code Version
code
01 PV 016/020/023 Flow
F
02 PV 032/040/046 control
03 PV 063/080/092
04 PC 140/180
05 PV 270

PQ-F00_gb.PM6.5MM

Hydraulics 10-2
Power Amplifier for Pumps
Characteristics Series PQ-F00 I-2.2
Circuit diagram

0V=terminal 3

MIN/MAX setting Connection examples


The minimum setting can be used to adjust the lower
working point of a valve.
The maximum setting is used to maintain the input sig-
nal range to the required working range of the valve.
Adjustment sequence:
1. Put input to 0V potential.
2. Adjust bounce value with trimmer “min”.
3. Feed a signal of +10V (or +20mA) to the input
4. Adjust the required maximum value with trimmer
“max”.
Please note that MIN must always be adjusted before
MAX.

Dimensions
75

90 110

PQ-F00_gb.PM6.5MM

Hydraulics 10-3

You might also like