0% found this document useful (0 votes)

221 views176 pages

H Series Serial Driver

plc

Uploaded by

sunhuynh

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

221 views176 pages

H Series Serial Driver

plc

Uploaded by

sunhuynh

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 176

Hitachi IES Co., Ltd.

H Series Serial Driver

1 System Configuration....................................................................................................... 3
2 Selection of External Device .......................................................................................... 10
3 Example of Communication Setting ............................................................................... 11
4 Setup Items .................................................................................................................... 95
5 Cable Diagram ............................................................................................................. 100
6 Supported Device......................................................................................................... 165
7 Device Code and Address Code.................................................................................. 172
8 Error Messages............................................................................................................ 175

1
H Series Serial Driver

PREFACE
This manual describes how to connect the Display and the External Device.
In this manual, the connection procedure will be described by following the below sections:

1 System Configuration
)"1 System Configuration" (page 3)
This section shows the types of External
Devices which can be connected and SIO
type.

2 Selection of External Device

)"2 Selection of External Device" (page 10)
Select a model (series) of the External
Device to be connected and connection
method.

3 Example of Communication Settings

)"3 Example of Communication Setting"
This section shows setting examples for
(page 11)
communicating between the Display and
the External Device.

Setup Items
4
This section describes communication
)"4 Setup Items" (page 95)
setup items on the Display.
Set communication settings of the Display
with GP-Pro EX or in off-line mode.

5 Cable Diagram
)"5 Cable Diagram" (page 100)
This section shows cables and adapters
for connecting the Display and the
External Device.

Operation

GP-Pro EX Device/PLC Connection Manual 2

H Series Serial Driver

1 System Configuration

The system configuration in the case when the External Device of Hitach IES Co., Ltd. and the Display are
connected is shown.

Setting Cable
Series CPU Link I/F SIO Type
Example Diagram

Setting Cable
Port on the CPU
H-20, H-28, H-40, H-64 RS232C Example 1 Diagram 1
unit (page 11) (page 100)

H-200(CPU-02H)*1 Setting Cable

Port on the CPU
H-250(CPU21-02H)*1 RS232C Example 1 Diagram 1
unit
H-252B(CPU22-02HB)*1 (page 11) (page 100)

Setting Cable
Port on the CPU
H-252C(CPU22-02HC)*1 *2 RS232C Example 1 Diagram 1
unit (page 11) (page 100)

Setting Cable
Port on the CPU
RS232C Example 1 Diagram 1
unit (page 11) (page 100)
H-300(CPU-03Ha)*1
Setting Cable
H H-700(CPU-07Ha)*1
RS232C Example 2 Diagram 1
(Procedure 1) H-2000(CPU-20Ha)*1 (page 13) (page 100)
H-2002(CPU2-20H)*1 COMM-H
COMM-2H Setting Cable
RS422/485
Example 3 Diagram 2
(4wire) (page 15) (page 102)

Setting Cable
Port on the CPU
RS232C Example 1 Diagram 1
unit (page 11) (page 100)
H-302(CPU2-03H)*1
Setting Cable
H-702(CPU2-07H)*1
RS232C Example 2 Diagram 1
H-4010(CPU3-40H)*1 (page 13) (page 100)
H-1002(CPU2-10H)*1 COMM-2H
Setting Cable
RS422/485
Example 3 Diagram 2
(4wire) (page 15) (page 102)

H-300(CPU-03Ha) Setting Cable

H-700(CPU-07Ha) RS232C Example 4 Diagram 1
H-2000(CPU-20Ha) (page 17) (page 100)
H H-302(CPU2-03H)
COMM-2H
(Procedure 2) H-702(CPU2-07H) Setting Cable
H-2002(CPU2-20H) RS422/485
Example 5 Diagram 2
H-4010(CPU3-40H) (4wire) (page 19) (page 102)
H-1002(CPU2-10H)

GP-Pro EX Device/PLC Connection Manual 3

H Series Serial Driver

Setting Cable
Series CPU Link I/F SIO Type
Example Diagram

EH-150(EH-CPU104)
EH-150(EH-CPU104A) Serial port 1 on
Setting Cable
EH-150(EH-CPU208) the CPU unit
RS232C Example 6 Diagram 3
EH-150(EH-CPU208A) Serial port 2 on (page 21) (page 106)
EH-150(EH-CPU308) the CPU unit
EH-150(EH-CPU316)

Setting Cable
RS232C Example 6 Diagram 3
(page 21) (page 106)

EH-150(EH-CPU308A) Setting Cable

Serial port 1 on RS422/485
EH-150(EH-CPU316A) Example 7 Diagram 4
the CPU unit (4wire) (page 23) (page 108)
EH-150(EH-CPU448)
EH-150(EH-CPU448A) Setting Cable
EH-150(EH-CPU516) RS422/485
Example 8 Diagram 5
EH-150(EH-CPU548) (2wire) (page 25) (page 112)
EH-150
(Procedure 1) Setting Cable
Serial port 2 on
RS232C Example 6 Diagram 3
the CPU unit (page 21) (page 106)

Setting Cable
Port1 on the
RS232C Example 9 Diagram 12
EH-SIO unit*3 (page 27) (page 152)

Setting Cable
RS232C*4 Example 10 Diagram 12
EH-150(EH-CPU516) (page 29) (page 152)
EH-150(EH-CPU548) Setting Cable
Port2 on the RS422/485
Example 11 Diagram 6
EH-SIO unit*3 (4wire)*4 (page 31) (page 119)

Setting Cable
RS422/485
Example 12 Diagram 7
(2wire)*4 (page 33) (page 123)

GP-Pro EX Device/PLC Connection Manual 4

H Series Serial Driver

Setting Cable
Series CPU Link I/F SIO Type
Example Diagram

Setting Cable
EH-150(EH-CPU104A) Serial port 1 on
RS232C Example 13 Diagram 3
EH-150(EH-CPU208A) the CPU unit (page 35) (page 106)

Setting Cable
RS232C Example 13 Diagram 3
EH-150(EH-CPU308A) (page 35) (page 106)
EH-150(EH-CPU316A)
Setting Cable
EH-150(EH-CPU448) Serial port 1 on RS422/485
Example 14 Diagram 4
EH-150(EH-CPU448A) the CPU unit (4wire) (page 37) (page 108)
EH-150(EH-CPU516)
EH-150(EH-CPU548) Setting Cable
RS422/485
Example 15 Diagram 5
EH-150 (2wire) (page 39) (page 112)
(Procedur
e 2) Setting Cable
Port1 on the
RS232C Example 16 Diagram 12
EH-SIO unit*3 (page 41) (page 152)

Setting Cable
RS232C*4 Example 17 Diagram 12
EH-150(EH-CPU516) (page 43) (page 152)
EH-150(EH-CPU548) Setting Cable
Port2 on the RS422/485
Example 18 Diagram 6
EH-SIO unit*3 (4wire)*4 (page 45) (page 119)

Setting Cable
RS422/485
Example 19 Diagram 7
(2wire)*4 (page 47) (page 123)

MICRO-EH(EH-D10)*5 Setting Cable

Port 1 on the
MICRO-EH(EH-A14)*5 RS232C Example 20 Diagram 3
CPU unit
MICRO-EH(EH-D14)*5 (page 49) (page 106)

Setting Cable
Port 1 on the
RS232C Example 20 Diagram 3
CPU unit (page 49) (page 106)
MICRO-EH(EH-A23)*5
Setting Cable
MICRO-EH(EH-D23)*5 RS422/485
Example 21 Diagram 8
MICRO-EH(EH-A28)*5 (4wire) (page 51) (page 130)
MICRO-EH(EH-D28)*5 Port 2 on the
CPU unit Setting Cable
RS422/485
MICRO- Example 22 Diagram 9
(2wire) (page 53) (page 134)
EH
(Procedure
Setting Cable
1) Port on the CPU
RS232C Example 20 Diagram 3
unit (page 49) (page 106)

MICRO-EH(EH-A64)*5 Setting Cable

MICRO-EH(EH-D64)*5 EH-OB232*6 RS232C Example 23 Diagram 3
MICRO-EH(EH-A40)*5 (page 55) (page 106)
MICRO-EH(EH-D40)*5 Setting Cable
MICRO-EH(EH-A20)*5 RS422/485
Example 24 Diagram 10
MICRO-EH(EH-D20)*5 (4wire) (page 57) (page 141)
EH-OB485*7
Setting Cable
RS422/485
Example 25 Diagram 11
(2wire) (page 59) (page 145)

GP-Pro EX Device/PLC Connection Manual 5

H Series Serial Driver

Setting Cable
Series CPU Link I/F SIO Type
Example Diagram

MICRO-EH(EH-D10)*5 Setting Cable

Port 1 on the
MICRO-EH(EH-A14)*5 RS232C Example 26 Diagram 3
CPU unit
MICRO-EH(EH-D14)*5 (page 61) (page 106)

Setting Cable
Port 1 on the
RS232C Example 26 Diagram 3
CPU unit (page 61) (page 106)
MICRO-EH(EH-A23)*5
Setting Cable
MICRO-EH(EH-D23)*5 RS422/485
Example 27 Diagram 8
MICRO-EH(EH-A28)*5 (4wire) (page 63) (page 130)
MICRO-EH(EH-D28)*5 Port 2 on the
CPU unit Setting Cable
RS422/485
MICRO- Example 28 Diagram 9
(2wire) (page 65) (page 134)
EH
(Procedure
Setting Cable
2) Port on the CPU
RS232C Example 26 Diagram 3
unit (page 61) (page 106)

MICRO-EH(EH-A64)*5 Setting Cable

MICRO-EH(EH-D64)*5 EH-OB232*6 RS232C Example 29 Diagram 3
MICRO-EH(EH-A40)*5 (page 67) (page 106)
MICRO-EH(EH-D40)*5 Setting Cable
MICRO-EH(EH-A20)*5 RS422/485
Example 30 Diagram 10
MICRO-EH(EH-D20)*5 (4wire) (page 69) (page 141)
EH-OB485*7
Setting Cable
RS422/485
Example 31 Diagram 11
(2wire) (page 71) (page 145)

Setting Cable
Serial port on
EH-WD10DR RS232C Example 32 Diagram 3
the CPU unit (page 73) (page 106)

Setting Cable
Web RS232C Example 40 Diagram 3
controller (page 89) (page 106)
(Procedure Setting Cable
1 and 2) Serial port on RS422/485
EH-WA23DR Example 41 Diagram 13
the CPU unit (4wire) (page 91) (page 153)

Setting Cable
RS422/485
Example 42 Diagram 14
(2wire) (page 93) (page 158)

GP-Pro EX Device/PLC Connection Manual 6

H Series Serial Driver

Setting Cable
Series CPU Link I/F SIO Type
Example Diagram

Setting Cable
RS232C Example 33 Diagram 3
(page 75) (page 106)

Setting Cable
Serial port on RS422/485
Example 34 Diagram 4
the CPU unit (4wire) (page 77) (page 108)

Setting Cable
R422/S485
Example 35 Diagram 5
(2wire) (page 79) (page 112)
EHV-CPU128
EHV Setting Cable
EHV-CPU64 Port 1 on the
(Procedure RS232C Example 36 Diagram 12
EHV-CPU32 EH-SIO unit*3 (page 81) (page 152)
1 and 2)
EHV-CPU16
Setting Cable
RS232C Example 37 Diagram 12
(page 83) (page 152)

Setting Cable
Port 2 on the RS422/485
Example 38 Diagram 6
EH-SIO unit*3 (4wire) (page 85) (page 119)

Setting Cable
RS422/485
Example 39 Diagram 7
(2wire) (page 87) (page 123)

*1 Connect to the peripheral port on the CPU module.

*2 When the peripheral port 2 on the CPU unit is used, CNCOM-05 conversion cable by Hitachi IES Co., Ltd. needs to be used
between the 8 pin connector and D-sub 15 pin connecter.
*3 Version 2.0 or later of the EH-SIO software supports Procedure 1; version 2.1 or later supports Procedure 2. Furthermore,
only EH-CPU548(Ver.E402 or later)/EH-CPU516(Ver.E202 or later) can use EH-SIO.
*4 Bit8 is used for interface selection of Port2 (RS232C or RS422/485).
*5 Model No. of the External Device "" differs depending on the specification of each External Device.
*6 Communication board (RS232C).Can be used in the CPU of which version is Ver.0101 or later.
*7 Communication board (RS422/RS485).Can be used in the CPU of which version is Ver.0100 or later.

GP-Pro EX Device/PLC Connection Manual 7

H Series Serial Driver

COM Port of IPC

When connecting IPC with External Device, the COM port which can be used changes with series and SIO type.
Please refer to the manual of IPC for details.

Usable port

Usable port
Series
RS-232C RS-422/485(4 wire) RS-422/485(2 wire)
*1
COM1 , COM2,
PS-2000B - -
COM3*1, COM4
PS-3450A, PS-3451A COM1, COM2*1*2 COM2*1*2 COM2*1*2
PS-3650A, PS-3651A COM1*1 - -
PS-3700A (Pentium®4-M) COM1*1, COM2 , *1
COM3*2 COM3*2
PS-3710A COM3*2 , COM4
PS-3711A COM1*1, COM2*2 COM2*2 COM2*2
COM1*1*2, COM2*1,
PL-3000B COM1*1*2 COM1*1*2
COM3, COM4
*1 The RI/5V can be switched. Please switch with the change switch of IPC.
*2 It is necessary to set up the SIO type with the Dip switch. Please set up as follows according to SIO
type to be used.

Dip switch setting: RS-232C

Dip switch Setting Description

1 OFF*1 Reserve (always OFF)
2 OFF
SIO type: RS-232C
3 OFF
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Does not Exist
8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Does not Exist
9 OFF
RS (RTS) Auto control mode: Disable
10 OFF
*1 It is necessary to turn ON the set value, only when using PS-3450A and PS-3451A.

GP-Pro EX Device/PLC Connection Manual 8

H Series Serial Driver

Dip switch setting: RS-422/485 (4 wire)

Dip switch Setting Description

1 OFF Reserve (always OFF)
2 ON
SIO type: RS-422/485
3 ON
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Does not Exist
8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Does not Exist
9 OFF
RS (RTS) Auto control mode: Disable
10 OFF

Dip switch setting: RS-422/485 (2 wire)

Dip switch Setting Description

1 OFF Reserve (always OFF)
2 ON
SIO type: RS-422/485
3 ON
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 ON Short-circuit of SDA (TXA) and RDA (RXA): Exist
8 ON Short-circuit of SDB (TXB) and RDB (RXB): Exist
9 ON
RS (RTS) Auto control mode: Enable
10 ON

GP-Pro EX Device/PLC Connection Manual 9

H Series Serial Driver

2 Selection of External Device

Select the External Device to be connected to the Display.

Setup Items Setup Description

Maker Select the maker of the External Device to be connected. Select "Hitachi IES Co., Ltd.".
Select a model (series) of the External Device to be connected and connection method.
Select "H Series SIO".
Driver Check the External Device which can be connected in "H Series SIO" in system
configuration.
) "1 System Configuration" (page 3)
Check this option when you synchronize the system data area of the Display and the device
(memory) of the External Device. When synchronized, you can use the ladder program of
the External Device to switch the display or display the window on the Display.
Cf. GP-Pro EXReference Manual "Appendix 1.4 LS Area (Direct Access
Method)"
Use System Area
This can be also set with GP-Pro EX or in off-line mode of the Display.
Cf. GP-Pro EX Reference Manual "5.17.6[ Setting Guide of [System Setting
Window], Setting Guide of [Main Unit Settings], System Area Setting"

Cf. Maintenance/Troubleshooting "2.15.1 Settings common to all Display

models System Area Settings"
Port Select the Display port to be connected to the External Device.

GP-Pro EX Device/PLC Connection Manual 10

H Series Serial Driver

3 Example of Communication Setting

Examples of communication settings of the Display and the External Device, recommended by Digital
Electronics Corp., are shown.

3.1 Setting Example 1

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 11

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Port on the CPU unit: H-4010 only)

Use the switch on the CPU unit for communication settings. After communication settings, turn ON the power of
the External Device again to enable the setting. Please refer to the manual of the External Device for more details.

Mode Setting Switch

• DIPSW1
DIP Switch Settings Description
SW03 OFF Port 1 Transmission Speed: 19,200 bps
SW04 OFF Port 2 Transmission Speed: 19,200 bps

• Other transmission speed settings are shown below.

DIP Switch Settings Description

SW03 ON Port 1 Transmission Speed: 38,400 bps
SW04 ON Port 2 Transmission Speed: 38,400 bps

GP-Pro EX Device/PLC Connection Manual 12

H Series Serial Driver

3.2 Setting Example 2

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 13

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device(COMM-H, COMM-2H)

Use the switch on the I/F unit for communication settings. After communication settings, turn ON the power of
the External Device again to enable the setting. Please refer to the manual of the External Device for more details.

Communication Setting Switch

DIP Switch Settings Description
01 OFF Bit Length: 7 bits
02 ON
03 ON Baud Rate Transmission Speed: 19,200bps
04 ON
05 ON Parity Enable/Disable: Enable
06 ON Parity Even/Odd: Even
07 OFF Stop Bit Length: 1 bit
08 ON Sum Check: Enable

Station Setting Rotary Switch

Rotary Switch Settings Description
x10 0 Station No. of External Device (tenth digit)
x1 0 Station No. of External Device (first digit)

Mode Setting Rotary Switch

Rotary Switch Settings Description
MODE 2 Procedure: Procedure 1

GP-Pro EX Device/PLC Connection Manual 14

H Series Serial Driver

3.3 Setting Example 3

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 15

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (COMM-H, COMM-2H)

Communication Setting Switch

Station Setting Rotary Switch

Rotary Switch Settings Description
x10 0 Station No. of External Device (tenth digit)
x1 0 Station No. of External Device (first digit)

Mode Setting Rotary Switch

Rotary Switch Settings Description
MODE 2 Procedure: Procedure 1

GP-Pro EX Device/PLC Connection Manual 16

H Series Serial Driver

3.4 Setting Example 4

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 17

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (COMM-2H)

Communication Setting Switch

Station Setting Rotary Switch

Rotary Switch Settings Description
x10 0 Station No. of External Device (tenth digit)
x1 0 Station No. of External Device (first digit)

Mode Setting Rotary Switch

Rotary Switch Settings Description
MODE 9 Procedure: Procedure 2

GP-Pro EX Device/PLC Connection Manual 18

H Series Serial Driver

3.5 Setting Example 5

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 19

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (COMM-2H)

Communication Setting Switch

Station Setting Rotary Switch

Rotary Switch Settings Description
x10 0 Station No. of External Device (tenth digit)
x1 0 Station No. of External Device (first digit)

Mode Setting Rotary Switch

Rotary Switch Settings Description
MODE 9 Procedure: Procedure 2

GP-Pro EX Device/PLC Connection Manual 20

H Series Serial Driver

3.6 Setting Example 6

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 21

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Serial port on the CPU unit)

Use the switch on the CPU unit for communication settings. SIO type will be set to RS232C (Procedure 1) by
entering 8000(H) in the address WRF037 with the ladder software (LADDER EDITOR for Windows). After
communication settings, turn ON the power of the External Device again to enable the setting. Please refer to the
manual of the External Device for more details.

Mode Setting Switch

DIP Switch Settings Description
SW03 ON
Port 1 Transmission Speed: 19,200 bps
SW04 OFF
SW05 ON Port 1 Operation: Specified port
SW06 OFF Port 2 Transmission Speed*1 : 4,800 bps or 19,200 bps
*1 When setting the transmission speed of Port 2 to 19,200 bps or 38,400 bps, set the port change switch
to High(ON).
Transmission speed of Port 2 will be set with SW06 and PHL switches.

Port Change Switch

PHL Switch Settings Description
PHL Switch ON Port 2 Operation

• When the change switch is ON, PHL signal becomes High(ON).

• Other transmission speed settings are shown below.
< Port 1 >
SW03 SW04 SW05 Transmission Speed
ON ON ON 4,800 bps
OFF ON ON 9,600 bps
OFF OFF ON 38,400 bps
< Port 2 >
SW06 PHL Speed Speed
OFF OFF 4,800 bps
ON OFF 9,600 bps
ON ON 38,400 bps

GP-Pro EX Device/PLC Connection Manual 22

H Series Serial Driver

3.7 Setting Example 7

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 23

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Serial port on the CPU unit)

Use the switch on the CPU unit for communication settings. SIO type will be set to RS422/RS485 (Procedure 1)
by entering A100(H)*1 in the address WRF037 with the ladder software (LADDER EDITOR for Windows). After
communication settings, turn ON the power of the External Device again to enable the setting. Please refer to the
manual of the External Device for more details.

*1 To enable the termination resistance, enter B100(H). In addition, enter the Station No. set on the Display in
lower 2 digits of A100 (or B100)
Mode Setting Switch
DIP Switch Settings Description
SW03 ON
Port 1 Transmission Speed: 19,200 bps
SW04 OFF
SW05 ON Port 1 Operation: Specified port

• Other transmission speed settings are shown below.

SW03 SW04 SW05 Speed Speed

ON ON ON 4,800 bps
OFF ON ON 9,600 bps
OFF OFF ON 38,400 bps

GP-Pro EX Device/PLC Connection Manual 24

H Series Serial Driver

3.8 Setting Example 8

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 25

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Serial port on the CPU unit)

Use the switch on the CPU unit for communication settings. SIO type will be set to RS422/RS485 (Procedure 1)
by entering A200(H)*1 in the address WRF037 with the ladder software (LADDER EDITOR for Windows). After
communication settings, turn ON the power of the External Device again to enable the setting. Please refer to the
manual of the External Device for more details.

*1 To enable the termination resistance, enter B200(H). In addition, enter the Station No. set on the Display in
lower 2 digits of A200 (or B200)
Mode Setting Switch
DIP Switch Settings Description
SW03 ON
Port 1 Transmission Speed: 19,200 bps
SW04 OFF
SW05 ON Port 1 Operation: Specified port

• Other transmission speed settings are shown below.

SW03 SW04 SW05 Speed Speed

ON ON ON 4,800 bps
OFF ON ON 9,600 bps
OFF OFF ON 38,400 bps

GP-Pro EX Device/PLC Connection Manual 26

H Series Serial Driver

3.9 Setting Example 9

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 27

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-SIO)

Use the switch on the EH-SIO for communication settings. After setting, assign I/O, and turn ON the power of the
External Device again to enable the setting.Use the ladder software (LADDER EDITOR for Windows) for the I/O
assignment.
Please refer to the manual of the External Device for more details.

Procedure
1. Use the DIP switch on the EH-SIO for communication settings.
DIP Switch Settings Description
01 OFF
02 ON Speed: 19,200 bps
Please refer to the manual of the External Device for more details about other
03 ON
transmission speed settings.
04 ON
05 OFF Transmission character configuration settings
06 ON Data Length: 7 bits
Stop Bit: 1 bit
07 OFF Parity: Even
08 OFF Always OFF

2. Ladder program is required for initial settings. Please refer to the manual of the External Device for more details.

GP-Pro EX Device/PLC Connection Manual 28

H Series Serial Driver

3.10 Setting Example 10

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 29

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-SIO)

Procedure
1. Use the DIP switch on the EH-SIO for communication settings.
Communication Setting Switch 2 (for Port 2)
DIP Switch Settings Description
01 OFF
02 ON Speed: 19,200 bps
Please refer to the manual of the External Device for more details about other
03 ON
transmission speed settings.
04 ON
05 OFF Transmission character configuration settings
06 ON Data Length: 7 bits
Stop Bit: 1 bit
07 OFF Parity: Even
08 OFF Interface Type: RS232C

2. Ladder program is required for initial settings. Please refer to the manual of the External Device for more details.

GP-Pro EX Device/PLC Connection Manual 30

H Series Serial Driver

3.11 Setting Example 11

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 31

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-SIO)

2. Ladder program is required for initial settings. Please refer to the manual of the External Device for more details.

GP-Pro EX Device/PLC Connection Manual 32

H Series Serial Driver

3.12 Setting Example 12

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 33

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-SIO)

2. Ladder program is required for initial settings. Please refer to the manual of the External Device for more details.

GP-Pro EX Device/PLC Connection Manual 34

H Series Serial Driver

3.13 Setting Example 13

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 35

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Serial port on the CPU unit)

Use the switch on the CPU unit for communication settings. SIO type will be set to RS232C (Procedure 2) by
entering C000(H) in the address WRF037 with the ladder software (LADDER EDITOR for Windows). After
communication settings, turn ON the power of the External Device again to enable the setting. Please refer to the
manual of the External Device for more details.

Mode Setting Switch

DIP Switch Settings Description
SW03 ON
Port 1 Transmission Speed: 19,200 bps
SW04 OFF
SW05 ON Port 1 Operation: Specified port

• Other transmission speed settings are shown below.

SW03 SW04 SW05 Speed Speed

ON ON ON 4,800 bps
OFF ON ON 9,600 bps
OFF OFF ON 38,400 bps

GP-Pro EX Device/PLC Connection Manual 36

H Series Serial Driver

3.14 Setting Example 14

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 37

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Serial port on the CPU unit)

Use the switch on the CPU unit for communication settings. SIO type will be set to RS422/RS485 (Procedure 2)
by entering E100(H)*1 in the address WRF037 with the ladder software (LADDER EDITOR for Windows). After
communication settings, turn ON the power of the External Device again to enable the setting. Please refer to the
manual of the External Device for more details.

*1 To enable the termination resistance, enter F100(H). In addition, enter the Station No. set on the Display in
lower 2 digits of E100 (or F100)
Mode Setting Switch
DIP Switch Settings Description
SW03 ON
Port 1 Transmission Speed: 19,200 bps
SW04 OFF
SW05 ON Port 1 Operation: Specified port

• Other transmission speed settings are shown below.

SW03 SW04 SW05 Speed Speed

ON ON ON 4,800 bps
OFF ON ON 9,600 bps
OFF OFF ON 38,400 bps

GP-Pro EX Device/PLC Connection Manual 38

H Series Serial Driver

3.15 Setting Example 15

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 39

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Serial port on the CPU unit)

Use the switch on the CPU unit for communication settings. SIO type will be set to RS422/RS485 (Procedure 2)
by entering E200(H)*1 in the address WRF037 with the ladder software (LADDER EDITOR for Windows). After
communication settings, turn ON the power of the External Device again to enable the setting. Please refer to the
manual of the External Device for more details.

*1 To enable the termination resistance, enter F200(H). In addition, enter the Station No. set on the Display in
lower 2 digits of E200 (or F200)
Mode Setting Switch
DIP Switch Settings Description
SW03 ON
Port 1 Transmission Speed: 19,200 bps
SW04 OFF
SW05 ON Port 1 Operation: Specified port

• Other transmission speed settings are shown below.

SW03 SW04 SW05 Speed Speed

ON ON ON 4,800 bps
OFF ON ON 9,600 bps
OFF OFF ON 38,400 bps

GP-Pro EX Device/PLC Connection Manual 40

H Series Serial Driver

3.16 Setting Example 16

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 41

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-SIO)

2. Ladder program is required for initial settings. Please refer to the manual of the External Device for more details.

GP-Pro EX Device/PLC Connection Manual 42

H Series Serial Driver

3.17 Setting Example 17

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 43

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-SIO)

2. Ladder program is required for initial settings. Please refer to the manual of the External Device for more details.

GP-Pro EX Device/PLC Connection Manual 44

H Series Serial Driver

3.18 Setting Example 18

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 45

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-SIO)

2. Ladder program is required for initial settings. Please refer to the manual of the External Device for more details.

GP-Pro EX Device/PLC Connection Manual 46

H Series Serial Driver

3.19 Setting Example 19

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 47

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-SIO)

2. Ladder program is required for initial settings. Please refer to the manual of the External Device for more details.

GP-Pro EX Device/PLC Connection Manual 48

H Series Serial Driver

3.20 Setting Example 20

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 49

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Port on the CPU unit)

Use the ladder software (LADDER EDITOR for Windows) for communication settings. Please refer to the
manual of the External Device for more details.

Procedure
1. Use the DIP switch inside the front cover of the External Device to enable the communication with the ladder
software.
Set as the following table.
DIP Switch Settings Description
SW01 ON
Transmission Speed: 19,200 bps
SW02 OFF
Please refer to the manual of the External Device for more details about other
SW03 OFF transmission speed settings.
SW04 OFF

2. Set 0000(H) in I/O No.WRF01A and turn I/O No.R7F6 ON to write the settings in the FLASH memory in the
External Device.
• WRF01A
Limit Bit Settings Description
15 0 Procedure 1

• R7F6
Limit Bit Settings Description
- 1 Writing in FLASH memory

3. Turn ON the power of the External Device again.

GP-Pro EX Device/PLC Connection Manual 50

H Series Serial Driver

3.21 Setting Example 21

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 51

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Port on the CPU unit)

Use the ladder software (LADDER EDITOR for Windows) for communication settings. Please refer to the
manual of the External Device for more details.

Procedure
1. Set the following communication settings in I/O No.WRF03D and turn I/O No.R7F6 ON to write the settings
in the FLASH memory in the External Device.
• WRF03D
Limit Bit Settings Description
15 1*1 Setting Change Request
14 0 Procedure 1
13 1 Station No.: Enable
Transmission speed: 19,200bps
11 to 8 0010(H) Please refer to the manual of the External Device for more details about other
transmission speed settings.
7 to 0 0 Station No.*2
*1 For communication settings, set "1". It will be changed to "0" when turning the power of the External
Device again.
*2 Set the Station No. with BCD 2 digits. Bit position of 7 to 4 corresponds to the digit of 10, and of 3 to
0 corresponds to the digit of 1.

• R7F6
Limit Bit Settings Description
- 1 Writing in FLASH memory

2. Turn ON the power of the External Device again.

GP-Pro EX Device/PLC Connection Manual 52

H Series Serial Driver

3.22 Setting Example 22

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 53

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Port on the CPU unit)

Use the ladder software (LADDER EDITOR for Windows) for communication settings. Please refer to the
manual of the External Device for more details.

• R7F6
Limit Bit Settings Description
- 1 Writing in FLASH memory

2. Turn ON the power of the External Device again.

GP-Pro EX Device/PLC Connection Manual 54

H Series Serial Driver

3.23 Setting Example 23

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 55

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-OB232)

Use the ladder software (LADDER EDITOR for Windows) for communication settings. Please refer to the
manual of the External Device for more details.

Procedure
1. Set the following communication settings in I/O No.WRF03D and turn I/O No.R7F6 ON to write the settings
in the FLASH memory in the External Device.
• WRF03D
Limit Bit Settings Description
15 1*1 Setting Change Request
14 0 Procedure 1
13 0 Station No.: Disable
Transmission speed: 19,200bps
11 to 8 0010(H) Please refer to the manual of the External Device for more details about other
transmission speed settings.
*1 For communication settings, set "1". It will be changed to "0" when turning the power of the External
Device again.

• R7F6
Limit Bit Settings Description
- 1 Writing in FLASH memory

2. Turn ON the power of the External Device again.

GP-Pro EX Device/PLC Connection Manual 56

H Series Serial Driver

3.24 Setting Example 24

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 57

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-OB485)

Use the ladder software (LADDER EDITOR for Windows) for communication settings. Please refer to the
manual of the External Device for more details.

• R7F6
Limit Bit Settings Description
- 1 Writing in FLASH memory

2. Turn ON the power of the External Device again.

GP-Pro EX Device/PLC Connection Manual 58

H Series Serial Driver

3.25 Setting Example 25

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 59

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-OB485)

Use the ladder software (LADDER EDITOR for Windows) for communication settings. Please refer to the
manual of the External Device for more details.

• R7F6
Limit Bit Settings Description
- 1 Writing in FLASH memory

2. Turn ON the power of the External Device again.

GP-Pro EX Device/PLC Connection Manual 60

H Series Serial Driver

3.26 Setting Example 26

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 61

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Port on the CPU unit)

Use the ladder software (LADDER EDITOR for Windows) for communication settings. Please refer to the
manual of the External Device for more details.

Procedure
1. Use the DIP switch inside the front cover of the External Device to enable the communication with the ladder
software.
Set as the following table.
DIP Switch Settings Description
SW01 ON
Speed: 19,200 bps
SW02 OFF
Please refer to the manual of the External Device for more details about other
SW03 OFF
transmission speed settings.
SW04 OFF

2. Set 8000(H) in I/O No.WRF01A and turn I/O No.R7F6 ON to write the settings in the FLASH memory in the
External Device.
• WRF01A
Limit Bit Settings Description
15 1 Procedure 2

• R7F6
Limit Bit Settings Description
- 1 Writing in FLASH memory

3. Turn ON the power of the External Device again.

GP-Pro EX Device/PLC Connection Manual 62

H Series Serial Driver

3.27 Setting Example 27

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 63

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Port on the CPU unit)

Use the ladder software (LADDER EDITOR for Windows) for communication settings. Please refer to the
manual of the External Device for more details.

Procedure
1. Set the following communication settings in I/O No.WRF03D and turn I/O No.R7F6 ON to write the settings
in the FLASH memory in the External Device.
• WRF03D
Limit Bit Settings Description
15 1*1 Setting Change Request
14 1 Procedure 2
13 1 Station No.: Enable
Transmission speed: 19,200bps
11 to 8 0010(H) Please refer to the manual of the External Device for more details about other
transmission speed settings.
7 to 0 0 Station No.*2
*1 For communication settings, set "1". It will be changed to "0" when turning the power of the External
Device again.
*2 Set the Station No. with BCD 2 digits. Bit position of 7 to 4 corresponds to the digit of 10, and of 3 to
0 corresponds to the digit of 1.

• R7F6
Limit Bit Settings Description
- 1 Writing in FLASH memory

2. Turn ON the power of the External Device again.

GP-Pro EX Device/PLC Connection Manual 64

H Series Serial Driver

3.28 Setting Example 28

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 65

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Port on the CPU unit)

Use the ladder software (LADDER EDITOR for Windows) for communication settings. Please refer to the
manual of the External Device for more details.

Procedure
1. Set the following communication settings in I/O No.WRF03D and turn I/O No.R7F6 ON to write the settings
in the FLASH memory in the External Device.
• WRF03D
Limit Bit Settings Description
15 1*1 Setting Change Request
14 1 Procedure 2
13 1 Station No.: Enable
Transmission speed: 19,200bps
11 to 8 0010(H) Please refer to the manual of the External Device for more details about other
transmission speed settings.
7 to 0 0 Station No.*2
*1 For communication settings, set "1". It will be changed to "0" when turning the power of the External
Device again.
*2 Set the Station No. with BCD 2 digits. Bit position of 7 to 4 corresponds to the digit of 10, and of 3 to
0 corresponds to the digit of 1.

• R7F6
Limit Bit Settings Description
- 1 Writing in FLASH memory

2. Turn ON the power of the External Device again.

GP-Pro EX Device/PLC Connection Manual 66

H Series Serial Driver

3.29 Setting Example 29

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 67

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-OB232)

Use the ladder software (LADDER EDITOR for Windows) for communication settings. Please refer to the
manual of the External Device for more details.

Procedure
1. Set the following communication settings in I/O No.WRF03D and turn I/O No.R7F6 ON to write the settings
in the FLASH memory in the External Device.
• WRF03D
Limit Bit Settings Description
15 1*1 Setting Change Request
14 1 Procedure 2
13 0 Station No.: Disable
Transmission speed: 19,200bps
11 to 8 0010(H) Please refer to the manual of the External Device for more details about other
transmission speed settings.
*1 For communication settings, set "1". It will be changed to "0" when turning the power of the External
Device again.

• R7F6
Limit Bit Settings Description
- 1 Writing in FLASH memory

2. Turn ON the power of the External Device again.

GP-Pro EX Device/PLC Connection Manual 68

H Series Serial Driver

3.30 Setting Example 30

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 69

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-OB485)

Use the ladder software (LADDER EDITOR for Windows) for communication settings. Please refer to the
manual of the External Device for more details.

Procedure
1. Set the following communication settings in I/O No.WRF03D and turn I/O No.R7F6 ON to write the settings
in the FLASH memory in the External Device.
• WRF03D
Limit Bit Settings Description
15 1*1 Setting Change Request
14 1 Procedure 2
13 1 Station No.: Enable
Transmission speed: 19,200bps
11 to 8 0010(H) Please refer to the manual of the External Device for more details about other
transmission speed settings.
7 to 0 0 Station No.*2
*1 For communication settings, set "1". It will be changed to "0" when turning the power of the External
Device again.
*2 Set the Station No. with BCD 2 digits. Bit position of 7 to 4 corresponds to the digit of 10, and of 3 to
0 corresponds to the digit of 1.

• R7F6
Limit Bit Settings Description
- 1 Writing in FLASH memory

2. Turn ON the power of the External Device again.

GP-Pro EX Device/PLC Connection Manual 70

H Series Serial Driver

3.31 Setting Example 31

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 71

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-OB485)

Use the ladder software (LADDER EDITOR for Windows) for communication settings. Please refer to the
manual of the External Device for more details.

Procedure
1. Set the following communication settings in I/O No.WRF03D and turn I/O No.R7F6 ON to write the settings
in the FLASH memory in the External Device.
• WRF03D
Limit Bit Settings Description
15 1*1 Setting Change Request
14 1 Procedure 2
13 1 Station No.: Enable
Transmission speed: 19,200bps
11 to 8 0010(H) Please refer to the manual of the External Device for more details about other
transmission speed settings.
7 to 0 0 Station No.*2
*1 For communication settings, set "1". It will be changed to "0" when turning the power of the External
Device again.
*2 Set the Station No. with BCD 2 digits. Bit position of 7 to 4 corresponds to the digit of 10, and of 3 to
0 corresponds to the digit of 1.

• R7F6
Limit Bit Settings Description
- 1 Writing in FLASH memory

2. Turn ON the power of the External Device again.

GP-Pro EX Device/PLC Connection Manual 72

H Series Serial Driver

3.32 Setting Example 32

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 73

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Web controller)

Use the Web Browser to access the External Device for communication setting. Please refer to the manual of the
External Device for more details.

Procedure
Please refer to the manual of the Web controller for more details.
1. If you set the operation mode setting switch of the External Device as follows, the temporary IP address of the
Ethernet port will be set to 192.168.0.1.
<Operation Mode Setting Switch>
•Set the rotary switch to "2"
2. Use the LAN cable to connect the Ethernet port of PC to the Ethernet port of the Web controller.(connect via
HUB or with the cross cable directly.)
3. Enter "http://192.168.0.1/mwconfig.cgi" in the address input box of the Web Browser to access the External
Device.
To access, you need to set the upper 3 bytes of PC's IP address to 192.168.0.. (ex. 192.168.0.10)
4. Login in the displayed System Configuration Login screen.
5. Select [Serial Protocol]-[Passive HIProtocol] from [System Configuration] on the displayed screen for
communication settings. After settings, click [SET] to confirm the setting values.
Serial-Passive HIProtocol
Setup Items Setting Value
Interface Type RS232C
Transmission Control Procedure Procedure1 1:1*1
Transmission Speed 19.2 kbps
Station No. 0
*1 To use Procedure 2, select [Procedure2 1:1].

6. Set the operation mode setting switch of the External Device and turn ON the power again.
<Operation Mode Setting Switch>
•Set the rotary switch to "0"

GP-Pro EX Device/PLC Connection Manual 74

H Series Serial Driver

3.33 Setting Example 33

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 75

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Serial port on the CPU unit)

Use the programming software (Control Editor) for communication settings. Please refer to the manual of the
External Device for more details.

Procedure
1. Start the programming software and create the project. The project is displayed in the offline mode.
2. Select [Editor Communication Setting] from the [Tool] menu to display the communication setting dialog
box.
3. Select either "USB" or "Serial" for the communication method to transfer the communication setting to the
External Device and click [Setting].
4. Use the USB cable or serial cable (by Hitachi IES Co., Ltd.) to connect PC to the External Device.
5. Select [Mode Change] - [Online] from the [Online] menu to move to the online mode.
6. Select [CPU Settings] - [Serial Communication Settings] from the [Tool] menu to perform the communication
settings.
• CPU Communication Settings (Serial Communication Settings)
Setup Items Settings
Serial Communication Settings Specified
Port Type RS232C
Speed 19.2 kbps
Communication Procedure Procedure 1 (1:1)*1
*1 To use Procedure 2 for communication, select [Procedure 2 (1:1)].

7. Turn ON the power of the External Device again.

GP-Pro EX Device/PLC Connection Manual 76

H Series Serial Driver

3.34 Setting Example 34

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 77

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Serial port on the CPU unit)

Use the programming software (Control Editor) for communication settings. Please refer to the manual of the
External Device for more details.

Procedure
1. Start the programming software and create the project. The project is displayed in the offline mode.
2. Select [Editor Communication Setting] from the [Tool] menu to display the communication setting dialog
box.
3. Select either "USB" or "Serial" for the communication method to transfer the communication setting to the
External Device and click [Setting].
4. Use the USB cable or serial cable (by Hitachi IES Co., Ltd.) to connect PC to the External Device.
5. Select [Mode Change] - [Online] from the [Online] menu to move to the online mode.
6. Select [CPU Settings] - [Serial Communication Settings] from the [Tool] menu to perform the communication
settings.
• CPU Communication Settings (Serial Communication Settings)
Setup Items Settings
Serial Communication Settings Specified
Port Type RS422/RS485
Speed 19.2 kbps
Communication Procedure Procedure 1 (1:n)*1
Station No. Enter the Station No. set on the display.*2
*1 To use Procedure 2 for communication, select [Procedure 2 (1:n)].
*2 If you set the Station No. to "None", communication is not available.

7. Turn ON the power of the External Device again.

GP-Pro EX Device/PLC Connection Manual 78

H Series Serial Driver

3.35 Setting Example 35

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 79

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Serial port on the CPU unit)

Use the programming software (Control Editor) for communication settings. Please refer to the manual of the
External Device for more details.

Procedure
1. Start the programming software and create the project. The project is displayed in the offline mode.
2. Select [Editor Communication Setting] from the [Tool] menu to display the communication setting dialog
box.
3. Select either "USB" or "Serial" for the communication method to transfer the communication setting to the
External Device and click [Setting].
4. Use the USB cable or serial cable (by Hitachi IES Co., Ltd.) to connect PC to the External Device.
5. Select [Mode Change] - [Online] from the [Online] menu to move to the online mode.
6. Select [CPU Settings] - [Serial Communication Settings] from the [Tool] menu to perform the communication
settings.
• CPU Communication Settings (Serial Communication Settings)
Setup Items Settings
Serial Communication Settings Specified
Port Type RS422/RS485
Speed 19.2 kbps
Communication Procedure Procedure 1 (1:n)*1
Station No. Enter the Station No. set on the display.*2
*1 To use Procedure 2 for communication, select [Procedure 2 (1:n)].
*2 If you set the Station No. to "None", communication is not available.

7. Turn ON the power of the External Device again.

GP-Pro EX Device/PLC Connection Manual 80

H Series Serial Driver

3.36 Setting Example 36

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 81

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-SIO)

Procedure
1. Use the DIP switch on the EH-SIO for communication settings.
• Communication Setting Switch 1 (for Port 1)
DIP Switch Settings Description
01 OFF
02 ON Speed: 19,200 bps
Please refer to the manual of the External Device for more details about other
03 ON
transmission speed settings.
04 ON
05 OFF Transmission character configuration settings
06 ON Data Length: 7 bits
Stop Bit: 1 bit
07 OFF Parity: Even
08 OFF Always OFF

2. Ladder program is required for initial settings. Please refer to the manual of the External Device for more
details.

GP-Pro EX Device/PLC Connection Manual 82

H Series Serial Driver

3.37 Setting Example 37

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 83

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-SIO)

Procedure
1. Use the DIP switch on the EH-SIO for communication settings.
• Communication Setting Switch 2 (for Port 2)
DIP Switch Settings Description
01 OFF
02 ON Speed: 19,200 bps
Please refer to the manual of the External Device for more details about other
03 ON
transmission speed settings.
04 ON
05 OFF Transmission character configuration settings
06 ON Data Length: 7 bits
Stop Bit: 1 bit
07 OFF Parity: Even
08 OFF Interface Type: RS232C

2. Ladder program is required for initial settings. Please refer to the manual of the External Device for more
details.

GP-Pro EX Device/PLC Connection Manual 84

H Series Serial Driver

3.38 Setting Example 38

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 85

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-SIO)

2. Ladder program is required for initial settings. Please refer to the manual of the External Device for more
details.

GP-Pro EX Device/PLC Connection Manual 86

H Series Serial Driver

3.39 Setting Example 39

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 87

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (EH-SIO)

2. Ladder program is required for initial settings. Please refer to the manual of the External Device for more
details.

GP-Pro EX Device/PLC Connection Manual 88

H Series Serial Driver

3.40 Setting Example 40

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 89

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Web controller)

Use the Web Browser to access the External Device for communication setting. Please refer to the manual of the
External Device for more details.

Procedure
Please refer to the manual of the Web controller for more details.
1. If you set the operation mode setting switch of the External Device as follows, the temporary IP address of the
Ethernet port will be set to 192.168.0.1.
<Operation Mode Setting Switch>
•Set only the DIP switch4 to ON
2. Use the LAN cable to connect the Ethernet port of PC to the Ethernet port of the Web controller.(connect via
HUB or with the cross cable directly.)
3. Enter "http://192.168.0.1/mwconfig.cgi" in the address input box of the Web Browser to access the External
Device.
To access, you need to set the upper 3 bytes of PC's IP address to 192.168.0.. (ex. 192.168.0.10)
4. Login in the displayed System Configuration Login screen.
5. Select [Serial Protocol]-[Passive HIProtocol] from [System Configuration] on the displayed screen for
communication settings. After settings, click [SET] to confirm the setting values.
Serial-Passive HIProtocol
Setup Items Setting Value
Interface Type RS232C
Transmission Control Procedure Procedure1 1:1*1
Transmission Speed 19.2 kbps
Station No. 0
*1 To use Procedure 2, select [Procedure2 1:1].

6. Set the operation mode setting switch of the External Device and turn ON the power again.
<Operation Mode Setting Switch>
•Set all the DIP switch to OFF

GP-Pro EX Device/PLC Connection Manual 90

H Series Serial Driver

3.41 Setting Example 41

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 91

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Web controller)

Use the Web Browser to access the External Device for communication setting. Please refer to the manual of the
External Device for more details.

Procedure
Please refer to the manual of the Web controller for more details.
1. If you set the operation mode setting switch of the External Device as follows, the temporary IP address of the
Ethernet port will be set to 192.168.0.1.
<Operation Mode Setting Switch>
•Set only the DIP switch4 to ON
2. Use the LAN cable to connect the Ethernet port of PC to the Ethernet port of the Web controller.(connect via
HUB or with the cross cable directly.)
3. Enter "http://192.168.0.1/mwconfig.cgi" in the address input box of the Web Browser to access the External
Device.
To access, you need to set the upper 3 bytes of PC's IP address to 192.168.0.. (ex. 192.168.0.10)
4. Login in the displayed System Configuration Login screen.
5. Select [Serial Protocol]-[Passive HIProtocol] from [System Configuration] on the displayed screen for
communication settings. After settings, click [SET] to confirm the setting values.
Serial-Passive HIProtocol
Setup Items Setting Value
Interface Type RS-422/485
Transmission Control Procedure Procedure1 1:1*1
Transmission Speed 19.2 kbps
Station No. 0
*1 To use Procedure 2, select [Procedure2 1:1].

6. Set the operation mode setting switch of the External Device and turn ON the power again.
<Operation Mode Setting Switch>
•Set all the DIP switch to OFF

GP-Pro EX Device/PLC Connection Manual 92

H Series Serial Driver

3.42 Setting Example 42

Settings of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

GP-Pro EX Device/PLC Connection Manual 93

H Series Serial Driver

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].

Settings of External Device (Web controller)

Use the Web Browser to access the External Device for communication setting. Please refer to the manual of the
External Device for more details.

Procedure
Please refer to the manual of the Web controller for more details.
1. If you set the operation mode setting switch of the External Device as follows, the temporary IP address of the
Ethernet port will be set to 192.168.0.1.
<Operation Mode Setting Switch>
• Set only the DIP switch4 to ON
2. Use the LAN cable to connect the Ethernet port of PC to the Ethernet port of the Web controller.(connect via
HUB or with the cross cable directly.)
3. Enter "http://192.168.0.1/mwconfig.cgi" in the address input box of the Web Browser to access the External
Device.
To access, you need to set the upper 3 bytes of PC's IP address to 192.168.0.. (ex. 192.168.0.10)
4. Login in the displayed System Configuration Login screen.
5. Select [Serial Protocol]-[Passive HIProtocol] from [System Configuration] on the displayed screen for
communication settings. After settings, click [SET] to confirm the setting values.
Serial-Passive HIProtocol
Setup Items Setting Value
Interface Type RS-422/485
Transmission Control Procedure Procedure1 1:1*1
Transmission Speed 19.2 kbps
Station No. 0
*1 To use Procedure 2, select [Procedure2 1:1].

6. Set the operation mode setting switch of the External Device and turn ON the power again.
<Operation Mode Setting Switch>
•Set all the DIP switch to OFF

GP-Pro EX Device/PLC Connection Manual 94

H Series Serial Driver

4 Setup Items

Set communication settings of the Display with GP-Pro Ex or in off-line mode of the Display.
The setting of each parameter must be identical to that of External Device.
)"3 Example of Communication Setting" (page 11)

4.1 Setup Items in GP-Pro EX

Communication Settings
To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.

Setup Items Setup Description

SIO Type Select the SIO type to communicate with the External Device.
Speed Select speed between the External Device and the Display.
Data Length Select data length.
Parity Select how to check parity.
Stop Bit Select stop bit length.
Select the communication control method to prevent overflow of transmission and
Flow Control
reception data.
Use an integer from 1 to 127 to enter the time (s) for which the Display waits for the
Timeout
response from the External Device.
Continues to the next page.

GP-Pro EX Device/PLC Connection Manual 95

H Series Serial Driver

Setup Items Setup Description

In case of no response from the External Device, use an integer from 0 to 255 to enter how
Retry
many times the Display retransmits the command.
Use an integer from "0 to 255" to enter standby time (ms) for the Display from receiving
Wait To Send
packets to transmitting next commands.
Procedure Select the transmission control procedure on the External Device.
You can switch RI/VCC of the 9th pin when you select RS232C for SIO type.
RI/VCC It is necessary to change RI/5V by changeover switch of IPC when connect with IPC.
Please refer to the manual of the IPC for more detail.

Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings ] of [Device/PLC Settings ].
When connecting multiple External Devices, you can click from [Device-Specific Settings] of [Device/PLC
Settings] to add the External Device which is available to set.

Setup Items Setup Description

Series Selects a model of the External Device.
Station No. Enter the unit No. of the External Device.

GP-Pro EX Device/PLC Connection Manual 96

H Series Serial Driver

4.2 Settings in Off-Line Mode

• Refer to the Maintenance/Troubleshooting manual for information on how to enter off-line mode
or about the operation.

Cf. Maintenance/Troubleshooting Manual "2.2 Off-line Mode"

Communication Settings
To display the setting screen, touch [Device/PLC Settings] from [Peripheral Equipment Settings] in the off-line
mode. Touch the External Device you want to set from the displayed list.

Setup Items Setup Description

Select the SIO type to communicate with the External Device.

To make the communication settings correctly, confirm the serial interface specifications of
SIO Type Display unit for [SIO Type].
We cannot guarantee the operation if a communication type that the serial interface does
not support is specified.
For details concerning the serial interface specifications, refer to the manual for Display
unit.
Speed Select speed between the External Device and the Display.
Data Length Select data length.
Parity Select how to check parity.
Stop Bit Select stop bit length.
Select the communication control method to prevent overflow of transmission and
Flow Control
reception data.
Use an integer from 1 to 127 to enter the time (s) for which the Display waits for the
Timeout
response from the External Device.

GP-Pro EX Device/PLC Connection Manual 97

H Series Serial Driver

Setup Items Setup Description

Device Setting
To display the setting screen, touch [Device/PLC Settings] from [Peripheral Equipment Settings]. Touch the
External Device you want to set from the displayed list, and touch [Device Settings].

Setup Items Setup Description

Select the External Device to set. Device name is a title of the External Device set with GP-
Device/PLC name
Pro EX. (Initial value [PLC1])
Series Displays a model of the External Device.
Station No. Enter the unit No. of the External Device.

GP-Pro EX Device/PLC Connection Manual 98

H Series Serial Driver

Option
To display the setting screen, touch [Device/PLC Settings] from [Peripheral Equipment Settings]. Touch the
External Device you want to set from the displayed list, and touch [Option].

Setup Items Setup Description

Switches RI/VCC of the 9th pin.
RI/VCC It is necessary to change RI/5V by changeover switch of IPC when connect with IPC.
Please refer to the manual of the IPC for more detail.

GP-Pro EX Device/PLC Connection Manual 99

H Series Serial Driver

5 Cable Diagram
The cable diagram shown below may be different from the cable diagram recommended by Hitachi IES Co., Ltd.
Please be assured there is no operational problem in applying the cable diagram shown in this manual.
• The FG pin of the main body of the External Device must be D-class grounded. Please refer to the manual of
the External Device for more details.
• SG and FG are connected inside the Display. When connecting SG to the External Device, design the system
not to form short-circuit loop.
• Connect the isolation unit, when communication is not stabilized under the influence of a noise etc..

Cable Diagram 1

Display
Cable*1 Remarks
(Connection Port)

By Hitachi IES Co., Ltd.

GP (COM1) A
WVCB02H
ST (COM1) Cable length:
IPC*2 B Your own cable 1 15m or less
PC/AT
C Your own cable 2
*1 You need to change the wiring depending on the speed.
H-200 H-300/H-302
H-250 H-252C H-700/H-702 H-4010
H-252B H-2000/H-2002
Speed Wiring Speed Wiring Speed Wiring Speed Wiring
2400bps
4800bps B 2400bps 4800bps B 4800bps B
Peripheral Port 1 A
9600bps 4800bps
or B
9600bps
Serial Port 1 A C A 19200bps A, C
19200bps 19200bps 19200bps
C C 38400bps A,B,C
Peripheral Port 2 4800bps B 4800bps B
or - - A - - 19200bps A, C
Serial Port 2 19200bps
C 38400bps A,B,C

*2 Only the COM port which can communicate by RS-232C can be used.
) COM Port of IPC (page 8)

A. When using WVCB02H (2m) by Hitachi IES Co., Ltd.

External Device
Display WVCB02H D-sub 15 pin

GP-Pro EX Device/PLC Connection Manual 100

H Series Serial Driver

B. When using your own cable 1

External Device
D-Sub 9 pin (socket) D-Sub 15 pin
Shield
Pin Signal name Pin Signal name
2 RD(RXD) 2 SD
Display 3 SD(TXD) 3 RD
6 DR(DSR) 5 CS
4 ER(DTR) 7 DR
5 SG 9 SG
7 RS(RTS) 8 PHL
8 CS(CTS) 4 RS
Shell FG 14 PV12

C. When using your own cable 2

GP-Pro EX Device/PLC Connection Manual 101

H Series Serial Driver

Cable Diagram 2

Display
Cable Remarks
(Connection Port)

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
GP*1 (COM1) +
AGP-3302B (COM2) A Terminal block conversion adapter by Pro-face
ST*2 (COM2) CA3-ADPTRM-01
IPC*3 +
Your own cable

B Your own cable

Online adapter by Pro-face Cable length:

CA4-ADPONL-01 250m or less
+
C Terminal block conversion adapter by Pro-face
CA3-ADPTRM-01
GP*4 (COM2) +
Your own cable

Online adapter by Pro-face

CA4-ADPONL-01
D
+
Your own cable
*1 All GP models except AGP-3302B
*2 All ST models except AST-3211A
*3 Only the COM port which can communicate by RS-422/485 (4 wire) can be used.
) COM Port of IPC (page 8)
*4 All GP models except GP-3200 series and AGP-3302B

A. When using the COM port conversion adapter (CA3-ADPCOM-01), the terminal block conversion adapter
(CA3-ADPTRM-01) by Pro-face and your own cable
• 1:1 Connection
External Device
Signal name Shield Terminal block
TERM Signal name
Display RDA TXDP
CA3-ADPCOM-01
RDB TXDN
SDA RXDP Terminal
resistance
CA3-ADPTRM-01 SDB RXDN 120 Ω (1/2W)
SG TXDG
FG RXDG

Your own cable

GP-Pro EX Device/PLC Connection Manual 102

H Series Serial Driver

• 1:n Connection
External Device External Device
Signal name Shield Terminal block Terminal block
Shield
TERM Signal name Signal name
Display RDA TXDP TXDP
CA3-ADPCOM-01 Terminal
RDB TXDN TXDN resistance
120 Ω (1/2W)
SDA RXDP RXDP
CA3-ADPTRM-01 SDB RXDN RXDN
SG TXDG TXDG
FG RXDG RXDG

Your own cable

B. When your own cable is used

• 1:1 Connection
External Device
Terminal D-Sub 9 pin (socket) Terminal block
Shield
resistance Pin Signal name Signal name
120 Ω (1/2W)
1 RDA TXDP
Terminal
2 RDB TXDN resistance
Display 120 Ω (1/2W)
3 SDA RXDP
7 SDB RXDN
5 SG TXDG
4 ERA RXDG
8 CSA
9 ERB
6 CSB
Shell FG

• 1:n Connection

External Device External Device

Terminal D-Sub 9 pin (socket) Terminal block Terminal block
resistance Shield Shield
Pin Signal name Signal name Signal name
120Ω (1/2W)
1 RDA TXDP TXDP
Terminal
2 RDB TXDN TXDN resistance
120Ω (1/2W)
Display 3 SDA RXDP RXDP
7 SDB RXDN RXDN
5 SG TXDG TXDG
4 ERA RXDG RXDG
8 CSA
9 ERB
6 CSB
Shell FG

GP-Pro EX Device/PLC Connection Manual 103

H Series Serial Driver

C. When using the online adapter (CA4-ADPONL-01), the terminal block conversion adapter (CA3-ADPTRM-
01) by Pro-face and your own cable
• 1:1 Connection
External Device
Signal name Shield Terminal block
TERM Signal name
Display RDA TXDP
CA4-ADPONL-01 Terminal
RDB TXDN resistance
120 Ω (1/2W)
SDA RXDP
CA3-ADPTRM-01 SDB RXDN
SG TXDG
FG RXDG

Your own cable

• 1:n Connection
External Device External Device
Signal name Shield Terminal block Terminal block
Shield
TERM Signal name Signal name
Display RDA TXDP TXDP
CA4-ADPONL-01 Terminal
RDB TXDN TXDN resistance
120 Ω (1/2W)
SDA RXDP RXDP
CA3-ADPTRM-01 SDB RXDN RXDN
SG TXDG TXDG
FG RXDG RXDG

Your own cable

D. When using the online adapter (CA4-ADPONL-01) by Pro-face and your own cable
• 1:1 Connection

D-Sub 9 pin (plug) External Device

Pin Signal name Shield Terminal block
CA4-ADPONL-01 1 TERMRX Signal name
Display 2 RDA TXDP
Terminal
7 RDB TXDN resistance
SDA 120 Ω (1/2W)
3 RXDP
8 SDB RXDN
5 SG TXDG
9 TERMTX RXDG
Shell FG

Your own cable

GP-Pro EX Device/PLC Connection Manual 104

H Series Serial Driver

• 1:n Connection
D-Sub 9 pin (plug) External Device External Device
Pin Signal name Shield Terminal block Terminal block
Shield
CA4-ADPONL-01 1 TERMRX Signal name Signal name
Display 2 RDA TXDP TXDP
Terminal
7 RDB TXDN TXDN resistance
3 SDA RXDP RXDP 120 Ω (1/2W)
8 SDB RXDN RXDN
5 SG TXDG TXDG
9 TERMTX RXDG RXDG
Shell FG

Your own cable

GP-Pro EX Device/PLC Connection Manual 105

H Series Serial Driver

Cable Diagram 3

Display
Cable*1 Remarks
(Connection Port)

By Hitachi IES Co., Ltd.

A
EH-VCB02(2m)

By Hitachi IES Co., Ltd.

WVCB02H(2m)
B +
Conversion cable by Hitachi IES Co., Ltd.
GP (COM1) EH-RS05(0.5m)
ST (COM1) Cable length:
IPC*2 Your own cable 1 15m or less
PC/AT +
C
Conversion cable by Hitachi IES Co., Ltd.
EH-RS05(0.5m)

Your own cable 2

+
D
Conversion cable by Hitachi IES Co., Ltd.
EH-RS05(0.5m)
*1 You need to change the wiring depending on the speed.
EH-150
Speed Wiring
4800bps A
Peripheral Port 1
9600bps B
or
19200bps C
Serial Port 1
38400bps D
4800bps A
Peripheral Port 2 9600bps C
or
19200bps B
Serial Port 2
38400bps D

*2 Only the COM port which can communicate by RS-232C can be used.
) COM Port of IPC (page 8)

A. When using the cable (EH-VCB02) by Hitachi IES Co., Ltd.

External Device
Display EH-VCB02 RJ-45 connector

B. When using the cable (WVCB02H) by Hitachi IES Co., Ltd. and the conversion cable (EH-RS05) by Hitachi
IES Co., Ltd.

External Device
Display WVCB02H RJ-45 connector
EH-RS05

GP-Pro EX Device/PLC Connection Manual 106

H Series Serial Driver

C. When using your own cable 1 and the conversion cable (EH-RS05) by Hitachi IES Co., Ltd.
External Device
D-Sub 9 pin (socket) D-Sub 15 pin (plug)
Shield External Device
Pin Signal name Pin Signal name RJ-45 conncetor
EH-RS05
2 RD(RXD) 2 SD
Display 3 SD(TXD) 3 RD
6 DR(DSR) 5 CS
4 ER(DTR) 7 DR
5 SG 9 SG
7 RS(RTS) 8 PHL
8 CS(CTS) 4 RS
Shell FG 14 PV12

Your own cable

D. When using your own cable 2 and the conversion cable (EH-RS05) by Hitachi IES Co., Ltd.
External Device
D-Sub 9 pin (socket) D-Sub 15 pin (plug) External Device
Shield RJ-45 conncetor
Pin Signal name Pin Signal name EH-RS05
2 RD(RXD) 2 SD
Display 3 SD(TXD) 3 RD
6 DR(DSR) 5 CS
4 ER(DTR) 7 DR
5 SG 9 SG
7 RS(RTS) 8 PHL
8 CS(CTS) 4 RS
Shell FG 14 PV12

Your own cable

GP-Pro EX Device/PLC Connection Manual 107

H Series Serial Driver

Cable Diagram 4

Display
Cable Remarks
(Connection Port)

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
+
Terminal block conversion adapter by Pro-face
A
GP*1 (COM1) CA3-ADPTRM-01
AGP-3302B (COM2) +
ST*2 (COM2) Conversion cable by Hitachi IES Co., Ltd.
IPC*3 EH-RS05

Your own cable

+
B
Conversion cable by Hitachi IES Co., Ltd.
EH-RS05

Online adapter by Pro-face Cable length:

CA4-ADPONL-01 500m or less
+
Terminal block conversion adapter by Pro-face
C
CA3-ADPTRM-01
+
Conversion cable by Hitachi IES Co., Ltd.
GP*4 (COM2) EH-RS05

Online adapter by Pro-face

CA4-ADPONL-01
+
D Your own cable
+
Conversion cable by Hitachi IES Co., Ltd.
EH-RS05
*1 All GP models except AGP-3302B
*2 All ST models except AST-3211A
*3 Only the COM port which can communicate by RS-422/485 (4 wire) can be used.
) COM Port of IPC (page 8)
*4 All GP models except GP-3200 series and AGP-3302B

GP-Pro EX Device/PLC Connection Manual 108

H Series Serial Driver

A. When using the COM port conversion adapter (CA3-ADPCOM-01), the terminal block conversion adapter
(CA3-ADPTRM-01) by Pro-face, your own cable and the conversion cable (EH-RS05) by Hitachi IES Co.,
Ltd.
• 1:1 Connection

External Device
Signal name D-Sub 15 pin (plug)
Shield
TERM Pin Signal name
External Device
Display RDA 14 TX RJ-45 conncetor
CA3-ADPCOM-01
RDB 2 TXN EH-RS05
SDA 7 RX
CA3-ADPTRM-01 SDB 3 RXN
SG 9 SG
FG

Your own cable

• 1:n Connection
External Device
Signal name D-Sub 15 pin (plug) D-Sub 15 pin (plug)
Shield
TERM Pin Signal name Pin Signal name
Display External Device
RDA 14 TX 14 TX RJ-45 conncetor
CA3-ADPCOM-01
RDB 2 TXN 2 TXN EH-RS05
SDA 7 RX 7 RX
CA3-ADPTRM-01 SDB 3 RXN 3 RXN
SG 9 SG 9 SG
FG

Your own cable

*For more information about the termination resistance, contact Hitachi IES Co., Ltd.

B. When using your own cable and the conversion cable (EH-RS05) by Hitachi IES Co., Ltd.
• 1:1 Connection

External Device
D-Sub 9 pin (socket) D-Sub 15 pin (plug)
Shield
Pin Signal name Pin Signal name External Device
1 RDA 14 TX RJ-45 conncetor
2 RDB 2 TXN EH-RS05
Display 3 SDA 7 RX
7 SDB 3 RXN
5 SG 9 SG
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG

GP-Pro EX Device/PLC Connection Manual 109

H Series Serial Driver

• 1:n Connection

External Device External Device

D-Sub 9 pin (socket) D-Sub 15 pin (plug) D-Sub 15 pin (plug)
Shield Shield
Pin Signal name Pin Signal name Pin Signal name
External Device
1 RDA 14 TX 14 TX RJ-45 conncetor
2 RDB 2 TXN 2 TXN EH-RS05
Display 3 SDA 7 RX 7 RX
7 SDB 3 RXN 3 RXN
5 SG 9 SG 9 SG
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG

*For more information about the termination resistance, contact Hitachi IES Co., Ltd.

External Device
Signal name Shield D-Sub 15 pin (plug)
TERM Pin Signal name
Display External Device
RDA 14 TX
CA4-ADPONL-01 RJ-45 conncetor
RDB 2 TXN EH-RS05
SDA 7 RX
CA3-ADPTRM-01 SDB 3 RXN
SG 9 SG
FG

Your own cable

• 1:n Connection

External Device External Device

Signal name D-Sub 15 pin (plug) D-Sub 15 pin (plug)
Shield Shield
TERM Pin Signal name Pin Signal name
Display External Device
RDA 14 TX 14 TX RJ-45 conncetor
CA4-ADPONL-01
RDB 2 TXN 2 TXN EH-RS05
SDA 7 RX 7 RX
CA3-ADPTRM-01 SDB 3 RXN 3 RXN
SG 9 SG 9 SG
FG

Your own cable

*For more information about the termination resistance, contact Hitachi IES Co., Ltd.

GP-Pro EX Device/PLC Connection Manual 110

H Series Serial Driver

D. When using the online adapter (CA4-ADPONL-01), your own cable and the conversion cable (EH-RS05) by
Hitachi IES Co., Ltd.
• 1:1 Connection
D-Sub 9 pin (plug)
External Device
Pin Signal name D-Sub 15 pin (plug)
CA4-ADPONL-01 Shield
1 TERMRX Pin Signal name External Device
Display 2 RDA 14 TX RJ-45 conncetor
7 RDB 2 TXN EH-RS05
3 SDA 7 RX
8 SDB 3 RXN
5 SG 9 SG
9 TERMTX
Shell FG

Your own cable

• 1:n Connection
D-Sub 9 pin (plug)
External Device External Device
Pin Signal name D-Sub 15 pin (plug) D-Sub 15 pin (plug)
Shield Shield
CA4-ADPONL-01 1 TERMRX Pin Signal name Pin Signal name
External Device
Display 2 RDA 14 TX 14 TX RJ-45 conncetor
7 RDB 2 TXN 2 TXN EH-RS05
3 SDA 7 RX 7 RX
8 SDB 3 RXN 3 RXN
5 SG 9 SG 9 SG
9 TERMTX
Shell FG

Your own cable

*For more information about the termination resistance, contact Hitachi IES Co., Ltd.

GP-Pro EX Device/PLC Connection Manual 111

H Series Serial Driver

Cable Diagram 5

Display
Cable Remarks
(Connection Port)

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
+
Terminal block conversion adapter by Pro-face
CA3-ADPTRM-01
A
+
GP*1 (COM1) Your own cable
AGP-3302B (COM2) +
ST*2 (COM2) Conversion cable by Hitachi IES Co., Ltd.
EH-RS05

Your own cable

+
B
Conversion cable by Hitachi IES Co., Ltd.
EH-RS05

Online adapter by Pro-face

CA4-ADPONL-01
+
Terminal block conversion adapter by Pro-face
CA3-ADPTRM-01
C
+
Your own cable
+
Conversion cable by Hitachi IES Co., Ltd. Cable length:
GP*3 (COM2)
EH-RS05 500m or less

Online adapter by Pro-face

CA4-ADPONL-01
+
D Your own cable
+
Conversion cable by Hitachi IES Co., Ltd.
EH-RS05

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
+
Terminal block conversion adapter by Pro-face
CA3-ADPTRM-01
E
+
Your own cable
IPC*4 +
Conversion cable by Hitachi IES Co., Ltd.
EH-RS05

Your own cable

+
F
Conversion cable by Hitachi IES Co., Ltd.
EH-RS05
*1 All GP models except AGP-3302B
*2 All ST models except AST-3211A
*3 All GP models except GP-3200 series and AGP-3302B
*4 Only the COM port which can communicate by RS-422/485 (2 wire) can be used.
) COM Port of IPC (page 8)

GP-Pro EX Device/PLC Connection Manual 112

H Series Serial Driver

External Device
Signal name Shield D-Sub 15 pin (plug)
External Device
TERM Pin Signal name RJ-45 conncetor
Display RDA 14 TX
CA3-ADPCOM-01 EH-RS05
RDB 2 TXN
SDA 7 RX
CA3-ADPTRM-01 SDB 3 RXN
SG 9 SG
FG

Your own cable

• 1:n Connection

External Device External Device

Signal name Shield D-Sub 15 pin (plug) Shield D-Sub 15 pin (plug)
TERM External Device
Pin Signal name Pin Signal name RJ-45 conncetor
Display RDA 14 TX 14 TX
CA3-ADPCOM-01 EH-RS05
RDB 2 TXN 2 TXN
SDA 7 RX 7 RX
CA3-ADPTRM-01 SDB 3 RXN 3 RXN
SG 9 SG 9 SG
FG

Your own cable

GP-Pro EX Device/PLC Connection Manual 113

H Series Serial Driver

B. When using your own cable and the conversion cable (EH-RS05) by Hitachi IES Co., Ltd.
• 1:1 Connection

External Device
D-Sub 9 pin (socket) D-Sub 15 pin (plug)
Terminal Shield External Device
resistance Pin Signal name Pin Signal name
100 Ω (1/2W) RJ-45 conncetor
1 RDA 14 TX EH-RS05
2 RDB 2 TXN
Display 3 SDA 7 RX
7 SDB 3 RXN
5 SG 9 SG
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG

• 1:n Connection
External Device External Device
D-Sub 9 pin (socket) D-Sub 15 pin (plug) Shield D-Sub 15 pin (plug)
Terminal Shield External Device
resistance Pin Signal name Pin Signal name Pin Signal name RJ-45 conncetor
100 Ω (1/2W)
1 RDA 14 TX 14 TX EH-RS05
2 RDB 2 TXN 2 TXN
Display 3 SDA 7 RX 7 RX
7 SDB 3 RXN 3 RXN
5 SG 9 SG 9 SG
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG

GP-Pro EX Device/PLC Connection Manual 114

H Series Serial Driver

C. When using the online adapter (CA4-ADPONL-01), the terminal block conversion adapter (CA3-ADPTRM-
01) by Pro-face, your own cable and the conversion cable (EH-RS05) by Hitachi IES Co., Ltd.
• 1:1 Connection
External Device
Signal name Shield D-Sub 15 pin (plug)
External Device
TERM Pin Signal name RJ-45 conncetor
Display RDA 14 TX
CA4-ADPONL-01 EH-RS05
RDB 2 TXN
SDA 7 RX
CA3-ADPTRM-01 SDB 3 RXN
SG 9 SG
FG

Your own cable

• 1:n Connection
External Device External Device
Signal name Shield D-Sub 15 pin (plug) Shield D-Sub 15 pin (plug) External Device
TERM Pin Signal name Pin Signal name RJ-45 conncetor
Display RDA 14 TX 14 TX EH-RS05
CA4-ADPONL-01
RDB 2 TXN 2 TXN
SDA 7 RX 7 RX
CA3-ADPTRM-01 SDB 3 RXN 3 RXN
SG 9 SG 9 SG
FG

Your own cable

GP-Pro EX Device/PLC Connection Manual 115

H Series Serial Driver

D. When using the online adapter (CA4-ADPONL-01), your own cable and the conversion cable (EH-RS05) by
Hitachi IES Co., Ltd.
• 1:1 Connection
D-Sub 9 pin (plug)
External Device
Pin Signal name Shield D-Sub 15 pin (plug) External Device
CA4-ADPONL-01 1 TERMRX Pin Signal name RJ-45 conncetor
Display 2 RDA 14 TX EH-RS05
7 RDB 2 TXN
3 SDA 7 RX
8 SDB 3 RXN
5 SG 9 SG
9 TERMTX
Shell FG

Your own cable

• 1:n Connection
D-Sub 9 pin (plug)
External Device External Device
Pin Signal name Shield D-Sub 15 pin (plug) Shield D-Sub 15 pin (plug)
CA4-ADPONL-01 1 TERMRX External Device
Pin Signal name Pin Signal name
RJ-45 conncetor
Display 2 RDA 14 TX 14 TX EH-RS05
7 RDB 2 TXN 2 TXN
3 SDA 7 RX 7 RX
8 SDB 3 RXN 3 RXN
5 SG 9 SG 9 SG
9 TERMTX
Shell FG

Your own cable

GP-Pro EX Device/PLC Connection Manual 116

H Series Serial Driver

E. When using the COM port conversion adapter (CA3-ADPCOM-01), the terminal block conversion adapter
(CA3-ADPTRM-01) by Pro-face, your own cable and the conversion cable (EH-RS05) by Hitachi IES Co.,
Ltd.
• 1:1 Connection
External Device
Signal name Shield D-Sub 15 pin (plug)
External Device
TERM Pin Signal name RJ-45 conncetor
Display RDA 7 RX
CA3-ADPCOM-01 EH-RS05
RDB 3 RXN
SDA 14 TX
CA3-ADPTRM-01 SDB 2 TXN
SG 9 SG
FG

Your own cable

• 1:n Connection
External Device External Device
Signal name Shield D-Sub 15 pin (plug) Shield D-Sub 15 pin (plug)
TERM External Device
Pin Signal name Pin Signal name RJ-45 conncetor
Display RDA 7 RX 7 RX
CA3-ADPCOM-01 EH-RS05
RDB 3 RXN 3 RXN
SDA 14 TX 14 TX
CA3-ADPTRM-01 SDB 2 TXN 2 TXN
SG 9 SG 9 SG
FG

Your own cable

GP-Pro EX Device/PLC Connection Manual 117

H Series Serial Driver

F. When using your own cable and the conversion cable (EH-RS05) by Hitachi IES Co., Ltd.
• 1:1 Connection
External Device
D-Sub 9 pin (socket) D-Sub 15 pin (plug)
Terminal Shield External Device
resistance Pin Signal name Pin Signal name RJ-45 conncetor
100Ω (1/2W)
1 DATA+ 7 RX EH-RS05
2 DATA- 3 RXN
Display 3 NC 14 TX
7 NC 2 TXN
5 GND(SG) 9 SG
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG

• 1:n Connection
External Device External Device
D-Sub 9 pin (socket) D-Sub 15 pin (plug) D-Sub 15 pin (plug)
Terminal Shield Shield External Device
resistance Pin Signal name Pin Signal name Pin Signal name RJ-45 conncetor
100Ω (1/2W)
1 DATA+ 7 RX 7 RX EH-RS05
2 DATA- 3 RXN 3 RXN
Display 3 NC 14 TX 14 TX
7 NC 2 TXN 2 TXN
5 GND(SG) 9 SG 9 SG
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG

GP-Pro EX Device/PLC Connection Manual 118

H Series Serial Driver

Cable Diagram 6

Display
Cable Remarks
(Connection Port)

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
GP*1 (COM1) +
AGP-3302B (COM2) A Terminal block conversion adapter by Pro-face
ST*2 (COM2) CA3-ADPTRM-01
IPC*3 +
Your own cable

B Your own cable

Online adapter by Pro-face Cable length:

CA4-ADPONL-01 500m or less
+
C Terminal block conversion adapter by Pro-face
CA3-ADPTRM-01
GP*4 (COM2) +
Your own cable

Online adapter by Pro-face

GP-Pro EX Device/PLC Connection Manual 119

H Series Serial Driver

A. When using the COM port conversion adapter (CA3-ADPCOM-01), the terminal block conversion adapter
(CA3-ADPTRM-01) by Pro-face and your own cable
• 1:1 Connection
Signal name External Device
Shield
TERM Pin Signal name
Display RDA 1 SD+
CA3-ADPCOM-01
RDB 2 SD-
SDA 3 RD+
CA3-ADPTRM-01 SDB 4 RD-
SG 6 SG
FG 5 TERM

Your own cable

• 1:n Connection
Signal name External Device External Device
Shield Shield
TERM Pin Signal name Pin Signal name
Display RDA 1 SD+ 1 SD+
CA3-ADPCOM-01
RDB 2 SD- 2 SD-
SDA 3 RD+ 3 RD+
CA3-ADPTRM-01 SDB 4 RD- 4 RD-
SG 6 SG 6 SG
FG 5 TERM 5 TERM

Your own cable

B. When your own cable is used

• 1:1 Connection

Terminal D-Sub 9 pin (socket) External Device

resistance Shield
Pin Signal name Pin Signal name
100 Ω (1/2W)
1 RDA 1 SD+
2 RDB 2 SD-
Display 3 SDA 3 RD+
7 SDB 4 RD-
5 SG 6 SG
4 ERA 5 TERM
8 CSA
9 ERB
6 CSB
Shell FG

GP-Pro EX Device/PLC Connection Manual 120

H Series Serial Driver

• 1:n Connection

Terminal D-Sub 9 pin (socket) External Device External Device

resistance Shield Shield
Pin Signal name Pin Signal name Pin Signal name
100 Ω (1/2W)
1 RDA 1 SD+ 1 SD+
2 RDB 2 SD- 2 SD-
Display 3 SDA 3 RD+ 3 RD+
7 SDB 4 RD- 4 RD-
5 SG 6 SG 6 SG
4 ERA 5 TERM 5 TERM
8 CSA
9 ERB
6 CSB
Shell FG

C. When using the online adapter (CA4-ADPONL-01), the terminal block conversion adapter (CA3-ADPTRM-
01) by Pro-face and your own cable
• 1:1 Connection

Signal name External Device

Shield
TERM Pin Signal name
Display RDA 1 SD+
CA4-ADPONL-01
RDB 2 SD-
SDA 3 RD+
CA3-ADPTRM-01 SDB 4 RD-
SG 6 SG
FG 5 TERM

Your own cable

• 1:n Connection

Signal name External Device External Device

Shield Shield
TERM Pin Signal name Pin Signal name
Display RDA 1 SD+ 1 SD+
CA4-ADPONL-01
RDB 2 SD- 2 SD-
SDA 3 RD+ 3 RD+
CA3-ADPTRM-01 SDB 4 RD- 4 RD-
SG 6 SG 6 SG
FG 5 TERM 5 TERM

Your own cable

GP-Pro EX Device/PLC Connection Manual 121

H Series Serial Driver

D. When using the online adapter (CA4-ADPONL-01) by Pro-face and your own cable
• 1:1 Connection

D-Sub 9 pin (plug)

Pin Signal name External Device
CA4-ADPONL-01 Shield
1 TERMRX Pin Signal name
Display 2 RDA 1 SD+
7 RDB 2 SD-
3 SDA 3 RD+
8 SDB 4 RD-
5 SG 6 SG
9 TERMTX 5 TERM
Shell FG

Your own cable

• 1:n Connection
D-Sub 9 pin (plug)
Pin Signal name External Device External Device
Shield Shield
CA4-ADPONL-01 1 TERMRX Pin Signal name Pin Signal name
Display 2 RDA 1 SD+ 1 SD+
7 RDB 2 SD- 2 SD-
3 SDA 3 RD+ 3 RD+
8 SDB 4 RD- 4 RD-
5 SG 6 SG 6 SG
9 TERMTX 5 TERM 5 TERM
Shell FG

Your own cable

GP-Pro EX Device/PLC Connection Manual 122

H Series Serial Driver

Cable Diagram 7

Display
Cable Remarks
(Connection Port)

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
+
GP*1 (COM1) A Terminal block conversion adapter by Pro-face
AGP-3302B (COM2) CA3-ADPTRM-01
ST*2 (COM2) +
Your own cable

B Your own cable

Online adapter by Pro-face

CA4-ADPONL-01
+
C Terminal block conversion adapter by Pro-face
CA3-ADPTRM-01
+ Cable length:
GP*3 (COM2)
Your own cable 500m or less

Online adapter by Pro-face

CA4-ADPONL-01
D
+
Your own cable

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
+
E Terminal block conversion adapter by Pro-face
IPC*4 CA3-ADPTRM-01
+
Your own cable

F Your own cable

*1 All GP models except AGP-3302B
*2 All ST models except AST-3211A
*3 All GP models except GP-3200 series and AGP-3302B
*4 Only the COM port which can communicate by RS-422/485 (2 wire) can be used.
) COM Port of IPC (page 8)

GP-Pro EX Device/PLC Connection Manual 123

H Series Serial Driver

A. When using the COM port conversion adapter (CA3-ADPCOM-01), the terminal block conversion adapter
(CA3-ADPTRM-01) by Pro-face and your own cable
• 1:1 Connection
Signal name Shield External Device
TERM Pin Signal name
Display RDA 1 SD+
CA3-ADPCOM-01
RDB 2 SD-
SDA 3 RD+
CA3-ADPTRM-01 SDB 4 RD-
SG 6 SG
FG 5 TERM

Your own cable

• 1:n Connection
Signal name Shield External Device Shield External Device
TERM Pin Signal name Pin Signal name
Display RDA 1 SD+ 1 SD+
CA3-ADPCOM-01
RDB 2 SD- 2 SD-
SDA 3 RD+ 3 RD+
CA3-ADPTRM-01 SDB 4 RD- 4 RD-
SG 6 SG 6 SG
FG 5 TERM 5 TERM

Your own cable

GP-Pro EX Device/PLC Connection Manual 124

H Series Serial Driver

B. When your own cable is used

• 1:1 Connection

Terminal D-Sub 9 pin (socket) External Device

resistance Shield
Pin Signal name Pin Signal name
100 Ω (1/2W)
1 RDA 1 SD+
2 RDB 2 SD-
Display 3 SDA 3 RD+
7 SDB 4 RD-
5 SG 6 SG
4 ERA 5 TERM
8 CSA
9 ERB
6 CSB
Shell FG

• 1:n Connection
D-Sub 9 pin (socket) External Device Shield External Device
Terminal Shield
resistance Pin Signal name Pin Signal name Pin Signal name
100 Ω (1/2W)
1 RDA 1 SD+ 1 SD+
2 RDB 2 SD- 2 SD-
Display 3 SDA 3 RD+ 3 RD+
7 SDB 4 RD- 4 RD-
5 SG 6 SG 6 SG
4 ERA 5 TERM 5 TERM
8 CSA
9 ERB
6 CSB
Shell FG

GP-Pro EX Device/PLC Connection Manual 125

H Series Serial Driver

C. When using the online adapter (CA4-ADPONL-01), the terminal block conversion adapter (CA3-ADPTRM-
01) by Pro-face and your own cable
• 1:1 Connection

Signal name Shield External Device

TERM Pin Signal name
Display RDA 1 SD+
CA4-ADPONL-01
RDB 2 SD-
SDA 3 RD+
CA3-ADPTRM-01 SDB 4 RD-
SG 6 SG
FG 5 TERM

Your own cable

• 1:n Connection
Signal name Shield External Device Shield External Device
TERM Pin Signal name Pin Signal name
Display RDA 1 SD+ 1 SD+
CA4-ADPONL-01
RDB 2 SD- 2 SD-
SDA 3 RD+ 3 RD+
CA3-ADPTRM-01 SDB 4 RD- 4 RD-
SG 6 SG 6 SG
FG 5 TERM 5 TERM

Your own cable

GP-Pro EX Device/PLC Connection Manual 126

H Series Serial Driver

D. When using the online adapter (CA4-ADPONL-01) by Pro-face and your own cable
• 1:1 Connection
D-Sub 9 pin (plug)
Pin Signal name Shield External Device
CA4-ADPONL-01 1 TERMRX Signal name
Pin
Display 2 RDA 1 SD+
7 RDB 2 SD-
3 SDA 3 RD+
8 SDB 4 RD-
5 SG 6 SG
9 TERMTX 5 TERM
Shell FG

Your own cable

• 1:n Connection
D-Sub 9 pin (plug)
Pin Signal name Shield External Device Shield External Device
CA4-ADPONL-01 1 TERMRX Signal name
Pin Pin Signal name
Display 2 RDA 1 SD+ 1 SD+
7 RDB 2 SD- 2 SD-
3 SDA 3 RD+ 3 RD+
8 SDB 4 RD- 4 RD-
5 SG 6 SG 6 SG
9 TERMTX 5 TERM 5 TERM
Shell FG

Your own cable

GP-Pro EX Device/PLC Connection Manual 127

H Series Serial Driver

E. When using the COM port conversion adapter (CA3-ADPCOM-01), the terminal block conversion adapter
(CA3-ADPTRM-01) by Pro-face and your own cable
• 1:1 Connection
Signal name Shield External Device
TERM Pin Signal name
Display RDA 3 RD+
CA3-ADPCOM-01
RDB 4 RD-
SDA 1 SD+
CA3-ADPTRM-01 SDB 2 SD-
SG 6 SG
FG 5 TERM

Your own cable

• 1:n Connection
Signal name Shield External Device Shield External Device
TERM Pin Signal name Pin Signal name
Display RDA 3 RD+ 3 RD+
CA3-ADPCOM-01
RDB 4 RD- 4 RD-
SDA 1 SD+ 1 SD+
CA3-ADPTRM-01 SDB 2 SD- 2 SD-
SG 6 SG 6 SG
FG 5 TERM 5 TERM

Your own cable

GP-Pro EX Device/PLC Connection Manual 128

H Series Serial Driver

F. When your own cable is used

• 1:1 Connection

Terminal D-Sub 9 pin (socket) External Device

resistance Shield
Pin Signal name Pin Signal name
100Ω (1/2W)
1 DATA+ 3 RD+
2 DATA- 4 RD-
Display 3 NC 1 SD+
7 NC 2 SD-
5 GND(SG) 6 SG
4 ERA 5 TERM
8 CSA
9 ERB
6 CSB
Shell FG

• 1:n Connection

Terminal D-Sub 9 pin (socket) External Device External Device

Shield Shield
resistance Signal name Signal name Signal name
Pin Pin Pin
100Ω (1/2W)
1 DATA+ 3 RD+ 3 RD+
2 DATA- 4 RD- 4 RD-
Display 3 NC 1 SD+ 1 SD+
7 NC 2 SD- 2 SD-
5 GND(SG) 6 SG 6 SG
4 ERA 5 TERM 5 TERM
8 CSA
9 ERB
6 CSB
Shell FG

GP-Pro EX Device/PLC Connection Manual 129

H Series Serial Driver

Cable Diagram 8

Display
Cable Remarks
(Connection Port)

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
GP*1 (COM1) +
AGP-3302B (COM2) A Terminal block conversion adapter by Pro-face
ST*2 (COM2) CA3-ADPTRM-01
IPC*3 +
Your own cable

B Your own cable

Online adapter by Pro-face Cable length:

CA4-ADPONL-01 250m or less
+
C Terminal block conversion adapter by Pro-face
CA3-ADPTRM-01
GP*4 (COM2) +
Your own cable

Online adapter by Pro-face

GP-Pro EX Device/PLC Connection Manual 130

H Series Serial Driver

A.When using the COM port conversion adapter (CA3-ADPCOM-01), the terminal block conversion adapter
(CA3-ADPTRM-01) by Pro-face and your own cable
• 1:1 Connection

External Device
Signal name D-Sub 15 pin (plug)
Shield
TERM Pin Signal name
Display RDA 13 SDP
CA3-ADPCOM-01
RDB 12 SDN
SDA 11 RDP
CA3-ADPTRM-01 SDB 10 RDN
SG 7 SG
FG 9 RT
14 RSP
15 CSN

Your own cable

• 1:n Connection
External Device External Device
Signal name D-Sub 15 pin (plug) D-Sub 15 pin (plug)
Shield Shield
TERM Pin Signal name Pin Signal name
Display RDA 13 SDP 13 SDP
CA3-ADPCOM-01
RDB 12 SDN 12 SDN
SDA 11 RDP 11 RDP
CA3-ADPTRM-01 SDB 10 RDN 10 RDN
SG 7 SG 7 SG
FG 9 RT 9 RT
14 RSP 14 RSP
15 CSN 15 CSN

Your own cable

B.When your own cable is used

• 1:1 Connection
External Device
D-Sub 9 pin (socket) D-Sub 15 pin (plug)
Terminal Shield
resistance Pin Signal name Pin Signal name
120 Ω (1/2W)
1 RDA 13 SDP
2 RDB 12 SDN
Display 3 SDA 11 RDP
7 SDB 10 RDN
5 SG 7 SG
4 ERA 9 RT
8 CSA 14 RSP
9 ERB 15 CSN
6 CSB
Shell FG

GP-Pro EX Device/PLC Connection Manual 131

H Series Serial Driver

• 1:n Connection

External Device External Device

D-Sub 9 pin (socket) D-Sub 15 pin (plug) D-Sub 15 pin (plug)
Terminal Shield Shield
resistance Pin Signal name Pin Signal name Pin Signal name
120 Ω (1/2W)
1 RDA 13 SDP 13 SDP
2 RDB 12 SDN 12 SDN
Display 3 SDA 11 RDP 11 RDP
7 SDB 10 RDN 10 RDN
5 SG 7 SG 7 SG
4 ERA 9 RT 9 RT
8 CSA 14 RSP 14 RSP
9 ERB 15 CSN 15 CSN
6 CSB
Shell FG

C. When using the online adapter (CA4-ADPONL-01), the terminal block conversion adapter (CA3-ADPTRM-
01) by Pro-face and your own cable
• 1:1 Connection
External Device
Signal name D-Sub 15 pin (plug)
Shield
TERM Pin Signal name
Display RDA 13 SDP
CA4-ADPONL-01
RDB 12 SDN
SDA 11 RDP
CA3-ADPTRM-01 SDB 10 RDN
SG 7 SG
FG 9 RT
14 RSP
15 CSN

Your own cable

• 1:n Connection
External Device External Device
Signal name D-Sub 15 pin (plug) D-Sub 15 pin (plug)
Shield Shield
TERM Pin Signal name Pin Signal name
Display RDA 13 SDP 13 SDP
CA4-ADPONL-01
RDB 12 SDN 12 SDN
SDA 11 RDP 11 RDP
CA3-ADPTRM-01 SDB 10 RDN 10 RDN
SG 7 SG 7 SG
FG 9 RT 9 RT
14 RSP 14 RSP
15 CSN 15 CSN

Your own cable

GP-Pro EX Device/PLC Connection Manual 132

H Series Serial Driver

D. When using the online adapter (CA4-ADPONL-01) by Pro-face and your own cable
• 1:1 Connection
D-Sub 9 pin (plug)
External Device
Pin Signal name D-Sub 15 pin (plug)
Shield
CA4-ADPONL-01 1 TERMRX Pin Signal name
Display 2 RDA 13 SDP
7 RDB 12 SDN
3 SDA 11 RDP
8 SDB 10 RDN
5 SG 7 SG
9 TERMTX 9 RT
Shell FG 14 RSP
15 CSN

Your own cable

• 1:n Connection
D-Sub 9 pin (plug)
External Device External Device
Pin Signal name D-Sub 15 pin (plug) D-Sub 15 pin (plug)
CA4-ADPONL-01 Shield Shield
1 TERMRX Pin Signal name Pin Signal name
Display 2 RDA 13 SDP 13 SDP
7 RDB 12 SDN 12 SDN
3 SDA 11 RDP 11 RDP
8 SDB 10 RDN 10 RDN
5 SG 7 SG 7 SG
9 TERMTX 9 RT 9 RT
Shell FG 14 RSP 14 RSP
15 CSN 15 CSN

Your own cable

GP-Pro EX Device/PLC Connection Manual 133

H Series Serial Driver

Cable Diagram 9

Display
Cable Remarks
(Connection Port)

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
+
GP*1 (COM1) A Terminal block conversion adapter by Pro-face
AGP-3302B (COM2) CA3-ADPTRM-01
ST*2 (COM2) +
Your own cable

B Your own cable

Online adapter by Pro-face Cable length:

CA4-ADPONL-01 250m or less
+
C Terminal block conversion adapter by Pro-face
CA3-ADPTRM-01
GP*3 (COM2) +
Your own cable

Online adapter by Pro-face

CA4-ADPONL-01
D
+
Your own cable

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
+
E Terminal block conversion adapter by Pro-face
IPC*4 CA3-ADPTRM-01
+
Your own cable

F Your own cable

GP-Pro EX Device/PLC Connection Manual 134

H Series Serial Driver

A. When using the COM port conversion adapter (CA3-ADPCOM-01), the terminal block conversion adapter
(CA3-ADPTRM-01) by Pro-face and your own cable
• 1:1 Connection
External Device
Signal name Shield D-Sub 15 pin (plug)
TERM Pin Signal name
Display RDA 13 SDP
CA3-ADPCOM-01
RDB 12 SDN
SDA 11 RDP
CA3-ADPTRM-01 SDB RDN
10
SG 7 SG
FG 9 RT
14 RSP
15 CSN

Your own cable

• 1:n Connection
External Device External Device
Signal name Shield D-Sub 15 pin (plug) D-Sub 15 pin (plug)
Shield
TERM Pin Signal name Pin Signal name
Display RDA 13 SDP 13 SDP
CA3-ADPCOM-01
RDB 12 SDN 12 SDN
SDA 11 RDP 11 RDP
CA3-ADPTRM-01 SDB RDN
10 10 RDN
SG 7 SG 7 SG
FG 9 RT 9 RT
14 RSP 14 RSP
15 CSN 15 CSN

Your own cable

GP-Pro EX Device/PLC Connection Manual 135

H Series Serial Driver

B.When your own cable is used

• 1:1 Connection

External Device
D-Sub 9 pin (socket) D-Sub 15 pin (plug)
Terminal Shield
resistance Pin Signal name Pin Signal name
120 Ω (1/2W)
1 RDA 13 SDP
2 RDB 12 SDN
Display 3 SDA 11 RDP
7 SDB 10 RDN
5 SG 7 SG
4 ERA 9 RT
8 CSA 14 RSP
9 ERB 15 CSN
6 CSB
Shell FG

• 1:n Connection

External Device External Device

D-Sub 9 pin (socket) D-Sub 15 pin (plug) Shield D-Sub 15 pin (plug)
Terminal Shield
resistance Pin Signal name Pin Signal name Pin Signal name
120 Ω (1/2W)
1 RDA 13 SDP 13 SDP
2 RDB 12 SDN 12 SDN
Display 3 SDA 11 RDP 11 RDP
7 SDB 10 RDN 10 RDN
5 SG 7 SG 7 SG
4 ERA 9 RT 9 RT
8 CSA 14 RSP 14 RSP
9 ERB 15 CSN 15 CSN
6 CSB
Shell FG

GP-Pro EX Device/PLC Connection Manual 136

H Series Serial Driver

C. When using the online adapter (CA4-ADPONL-01), the terminal block conversion adapter (CA3-ADPTRM-
01) by Pro-face and your own cable
• 1:1 Connection
External Device
Signal name Shield D-Sub 15 pin (plug)
TERM Pin Signal name
Display RDA 13 SDP
CA4-ADPONL-01
RDB 12 SDN
SDA 11 RDP
CA3-ADPTRM-01 SDB RDN
10
SG 7 SG
FG 9 RT
14 RSP
15 CSN

Your own cable

• 1:n Connection
External Device External Device
Signal name Shield D-Sub 15 pin (plug) D-Sub 15 pin (plug)
Shield
TERM Pin Signal name Pin Signal name
Display RDA 13 SDP 13 SDP
CA4-ADPONL-01
RDB 12 SDN 12 SDN
SDA 11 RDP 11 RDP
CA3-ADPTRM-01 SDB RDN
10 10 RDN
SG 7 SG 7 SG
FG 9 RT 9 RT
14 RSP 14 RSP
15 CSN 15 CSN

Your own cable

GP-Pro EX Device/PLC Connection Manual 137

H Series Serial Driver

D. When using the online adapter (CA4-ADPONL-01) by Pro-face and your own cable
• 1:1 Connection

D-Sub 9 pin (plug)

External Device
Pin Signal name Shield D-Sub 15 pin (plug)
CA4-ADPONL-01 1 TERMRX Pin Signal name
Display 2 RDA 13 SDP
7 RDB 12 SDN
3 SDA 11 RDP
8 SDB 10 RDN
5 SG 7 SG
9 TERMTX 9 RT
Shell FG 14 RSP
15 CSN

Your own cable

• 1:n Connection
D-Sub 9 pin (plug)
External Device External Device
Pin Signal name Shield D-Sub 15 pin (plug) Shield D-Sub 15 pin (plug)
CA4-ADPONL-01 1 TERMRX Pin Pin
Signal name Signal name
Display 2 RDA 13 SDP 13 SDP
7 RDB 12 SDN 12 SDN
3 SDA 11 RDP 11 RDP
8 SDB 10 RDN 10 RDN
5 SG 7 SG 7 SG
9 TERMTX 9 RT 9 RT
Shell FG 14 RSP 14 RSP
15 CSN 15 CSN

Your own cable

GP-Pro EX Device/PLC Connection Manual 138

H Series Serial Driver

E. When using the COM port conversion adapter (CA3-ADPCOM-01), the terminal block conversion adapter
(CA3-ADPTRM-01) by Pro-face and your own cable
• 1:1 Connection
External Device
Signal name Shield D-Sub 15 pin (plug)
TERM Pin Signal name
Display
CA3-ADPCOM-01 RDA 11 RDP
RDB 10 RDN
SDA 13 SDP
CA3-ADPTRM-01 SDB 12 SDN
SG 7 SG
FG 9 RT
14 RSP
15 CSN

Your own cable

• 1:n Connection
External Device External Device
Signal name Shield D-Sub 15 pin (plug) Shield D-Sub 15 pin (plug)
TERM Pin Signal name Pin Signal name
Display RDA 11 RDP 11 RDP
CA3-ADPCOM-01
RDB 10 RDN 10 RDN
SDA 13 SDP 13 SDP
CA3-ADPTRM-01 SDB 12 SDN 12 SDN
SG 7 SG 7 SG
FG 9 RT 9 RT
14 RSP 14 RSP
15 CSN 15 CSN

Your own cable

GP-Pro EX Device/PLC Connection Manual 139

H Series Serial Driver

F. When your own cable is used

• 1:1 Connection

External Device
D-Sub 9 pin (socket) D-Sub 15 pin (plug)
Terminal Shield
resistance Pin Signal name Pin Signal name
120Ω (1/2W)
1 DATA+ 11 RDP
2 DATA- 10 RDN
Display 3 NC 13 SDP
7 NC 12 SDN
5 GND(SG) 7 SG
4 ERA 9 RT
8 CSA 14 RSP
9 ERB 15 CSN
6 CSB
Shell FG

• 1:n Connection
External Device External Device
D-Sub 9 pin (socket) D-Sub 15 pin (plug) D-Sub 15 pin (plug)
Terminal Shield Shield
resistance Pin Signal name Pin Signal name Pin Signal name
120Ω (1/2W)
1 DATA+ 11 RDP 11 RDP
2 DATA- 10 RDN 10 RDN
Display 3 NC 13 SDP 13 SDP
7 NC 12 SDN 12 SDN
5 GND(SG) 7 SG 7 SG
4 ERA 9 RT 9 RT
8 CSA 14 RSP 14 RSP
9 ERB 15 CSN 15 CSN
6 CSB
Shell FG

GP-Pro EX Device/PLC Connection Manual 140

H Series Serial Driver

Cable Diagram 10

Display
Cable Remarks
(Connection Port)

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
GP*1 (COM1) +
AGP-3302B (COM2) A Terminal block conversion adapter by Pro-face
ST*2 (COM2) CA3-ADPTRM-01
IPC*3 +
Your own cable

B Your own cable

Online adapter by Pro-face Cable length:

CA4-ADPONL-01 500m or less
+
C Terminal block conversion adapter by Pro-face
CA3-ADPTRM-01
GP*4 (COM2) +
Your own cable

Online adapter by Pro-face

GP-Pro EX Device/PLC Connection Manual 141

H Series Serial Driver

A. When using the COM port conversion adapter (CA3-ADPCOM-01), the terminal block conversion adapter
(CA3-ADPTRM-01) by Pro-face and your own cable
• 1:1 Connection
External Device
Signal name RJ-45 conncetor
Shield
TERM Pin Signal name
Display RDA 4 SDP
CA3-ADPCOM-01
RDB 5 SDN
SDA 7 RDP
CA3-ADPTRM-01 SDB 6 RDN
SG 1 SG
FG 8 TERM

Your own cable

• 1:n Connection
External Device External Device
Signal name RJ-45 conncetor RJ-45 conncetor
Shield Shield
TERM Pin Signal name Pin Signal name
Display RDA 4 SDP 4 SDP
CA3-ADPCOM-01
RDB 5 SDN 5 SDN
SDA 7 RDP 7 RDP
CA3-ADPTRM-01 SDB 6 RDN 6 RDN
SG 1 SG 1 SG
FG 8 TERM 8 TERM

Your own cable

B. When your own cable is used

• 1:1 Connection

External Device
D-Sub 9 pin (socket) RJ-45 conncetor
Terminal Shield
resistance Pin Signal name Pin Signal name
120 Ω (1/2W)
1 RDA 4 SDP
2 RDB 5 SDN
Display 3 SDA 7 RDP
7 SDB 6 RDN
5 SG 1 SG
4 ERA 8 TERM
8 CSA
9 ERB
6 CSB
Shell FG

GP-Pro EX Device/PLC Connection Manual 142

H Series Serial Driver

• 1:n Connection
External Device External Device
D-Sub 9 pin (socket) RJ-45 conncetor RJ-45 conncetor
Terminal Shield Shield
resistance Pin Signal name Pin Signal name Pin Signal name
120 Ω (1/2W)
1 RDA 4 SDP 4 SDP
2 RDB 5 SDN 5 SDN
Display 3 SDA 7 RDP 7 RDP
7 SDB 6 RDN 6 RDN
5 SG 1 SG 1 SG
4 ERA 8 TERM 8 TERM
8 CSA
9 ERB
6 CSB
Shell FG

C. When using the online adapter (CA4-ADPONL-01), the terminal block conversion adapter (CA3-ADPTRM-
01) by Pro-face and your own cable
• 1:1 Connection

External Device
Signal name RJ-45 conncetor
Shield
TERM Pin Signal name
Display RDA 4 SDP
CA4-ADPONL-01
RDB 5 SDN
SDA 7 RDP
CA3-ADPTRM-01 SDB 6 RDN
SG 1 SG
FG 8 TERM

Your own cable

• 1:n Connection

External Device External Device

Signal name RJ-45 conncetor RJ-45 conncetor
Shield Shield
TERM Pin Signal name Pin Signal name
Display RDA 4 SDP 4 SDP
CA4-ADPONL-01
RDB 5 SDN 5 SDN
SDA 7 RDP 7 RDP
CA3-ADPTRM-01 SDB 6 RDN 6 RDN
SG 1 SG 1 SG
FG 8 TERM 8 TERM

Your own cable

GP-Pro EX Device/PLC Connection Manual 143

H Series Serial Driver

D.When using the online adapter (CA4-ADPONL-01) by Pro-face and your own cable
• 1:1 Connection
D-Sub 9 pin (plug) External Device
Pin Signal name RJ-45 conncetor
CA4-ADPONL-01 Shield
1 TERMRX Pin Signal name
Display 2 RDA 4 SDP
7 RDB 5 SDN
3 SDA 7 RDP
8 SDB 6 RDN
5 SG 1 SG
9 TERMTX 8 TERM
Shell FG

Your own cable

• 1:n Connection
D-Sub 9 pin (plug) External Device External Device
Pin Signal name RJ-45 conncetor RJ-45 conncetor
CA4-ADPONL-01 Shield Shield
1 TERMRX Pin Signal name Pin Signal name
Display 2 RDA 4 SDP 4 SDP
7 RDB 5 SDN 5 SDN
3 SDA 7 RDP 7 RDP
8 SDB 6 RDN 6 RDN
5 SG 1 SG 1 SG
9 TERMTX 8 TERM 8 TERM
Shell FG

Your own cable

GP-Pro EX Device/PLC Connection Manual 144

H Series Serial Driver

Cable Diagram 11

Display
Cable Remarks
(Connection Port)

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
+
GP*1 (COM1) A Terminal block conversion adapter by Pro-face
AGP-3302B (COM2) CA3-ADPTRM-01
ST*2 (COM2) +
Your own cable

B Your own cable

Online adapter by Pro-face

CA4-ADPONL-01
+
C Terminal block conversion adapter by Pro-face
CA3-ADPTRM-01
+ Cable length:
GP*3 (COM2)
Your own cable 500m or less

Online adapter by Pro-face

CA4-ADPONL-01
D
+
Your own cable

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
+
E Terminal block conversion adapter by Pro-face
IPC*4 CA3-ADPTRM-01
+
Your own cable

F Your own cable

GP-Pro EX Device/PLC Connection Manual 145

H Series Serial Driver

A. When using the COM port conversion adapter (CA3-ADPCOM-01), the terminal block conversion adapter
(CA3-ADPTRM-01) by Pro-face and your own cable
• 1:1 Connection

External Device
Signal name Shield RJ-45 conncetor
TERM Pin Signal name
Display RDA 4 SDP
CA3-ADPCOM-01
RDB 5 SDN
SDA 7 RDP
CA3-ADPTRM-01 SDB 6 RDN
SG 1 SG
FG 8 TERM

Your own cable

• 1:n Connection
External Device External Device
Signal name Shield RJ-45 conncetor RJ-45 conncetor
Shield
TERM Pin Signal name Pin Signal name
Display RDA 4 SDP 4 SDP
CA3-ADPCOM-01
RDB 5 SDN 5 SDN
SDA 7 RDP 7 RDP
CA3-ADPTRM-01 SDB 6 RDN 6 RDN
SG 1 SG 1 SG
FG 8 TERM 8 TERM

Your own cable

GP-Pro EX Device/PLC Connection Manual 146

H Series Serial Driver

B. When your own cable is used

• 1:1 Connection

GP-Pro EX Device/PLC Connection Manual 147

H Series Serial Driver

C. When using the online adapter (CA4-ADPONL-01), the terminal block conversion adapter (CA3-ADPTRM-
01) by Pro-face and your own cable
• 1:1 Connection
External Device
Signal name Shield RJ-45 conncetor
TERM Pin Signal name
Display RDA 4 SDP
CA4-ADPONL-01
RDB 5 SDN
SDA 7 RDP
CA3-ADPTRM-01 SDB 6 RDN
SG 1 SG
FG 8 TERM

Your own cable

• 1:n Connection
External Device External Device
Signal name Shield RJ-45 conncetor Shield RJ-45 conncetor
TERM Pin Signal name Pin Signal name
Display RDA 4 SDP 4 SDP
CA4-ADPONL-01
RDB 5 SDN 5 SDN
SDA 7 RDP 7 RDP
CA3-ADPTRM-01 SDB 6 RDN 6 RDN
SG 1 SG 1 SG
FG 8 TERM 8 TERM

Your own cable

GP-Pro EX Device/PLC Connection Manual 148

H Series Serial Driver

D. When using the online adapter (CA4-ADPONL-01) by Pro-face and your own cable
• 1:1 Connection

D-Sub 9 pin (plug)

External Device
Pin Signal name Shield RJ-45 conncetor
CA4-ADPONL-01 1 TERMRX Pin Signal name
Display 2 RDA 4 SDP
7 RDB 5 SDN
3 SDA 7 RDP
8 SDB 6 RDN
5 SG 1 SG
9 TERMTX 8 TERM
Shell FG

Your own cable

• 1:n Connection
D-Sub 9 pin (plug)
External Device External Device
Pin Signal name Shield RJ-45 conncetor Shield RJ-45 conncetor
CA4-ADPONL-01 1 TERMRX Pin Signal name Pin Signal name
Display 2 RDA 4 SDP 4 SDP
7 RDB 5 SDN 5 SDN
3 SDA 7 RDP 7 RDP
8 SDB 6 RDN 6 RDN
5 SG 1 SG 1 SG
9 TERMTX 8 TERM 8 TERM
Shell FG

Your own cable

GP-Pro EX Device/PLC Connection Manual 149

H Series Serial Driver

E. When using the COM port conversion adapter (CA3-ADPCOM-01), the terminal block conversion adapter
(CA3-ADPTRM-01) by Pro-face and your own cable
• 1:1 Connection
External Device
Signal name Shield RJ-45 conncetor
TERM Pin Signal name
Display RDA 7 RDP
CA3-ADPCOM-01
RDB 6 RDN
SDA 4 SDP
CA3-ADPTRM-01 SDB 5 SDN
SG 1 SG
FG 8 TERM

Your own cable

• 1:n Connection
External Device External Device
Signal name Shield RJ-45 conncetor Shield RJ-45 conncetor
TERM Pin Signal name Pin Signal name
Display RDA 7 RDP 7 RDP
CA3-ADPCOM-01
RDB 6 RDN 6 RDN
SDA 4 SDP 4 SDP
CA3-ADPTRM-01 SDB 5 SDN 5 SDN
SG 1 SG 1 SG
FG 8 TERM 8 TERM

Your own cable

GP-Pro EX Device/PLC Connection Manual 150

H Series Serial Driver

F. When your own cable is used

• 1:1 Connection

External Device
D-Sub 9 pin (socket) RJ-45 conncetor
Terminal Shield
resistance Pin Signal name Pin Signal name
120Ω (1/2W)
1 DATA+ 7 RDP
2 DATA- 6 RDN
Display 3 NC 4 SDP
7 NC 5 SDN
5 GND(SG) 1 SG
4 ERA 8 TERM
8 CSA
9 ERB
6 CSB
Shell FG

• 1:n Connection
External Device External Device
D-Sub 9 pin (socket) RJ-45 conncetor RJ-45 conncetor
Terminal Shield Shield
resistance Pin Signal name Pin Signal name Pin Signal name
120Ω (1/2W)
1 DATA+ 7 RDP 7 RDP
2 DATA- 6 RDN 6 RDN
Display 3 NC 4 SDP 4 SDP
7 NC 5 SDN 5 SDN
5 GND(SG) 1 SG 1 SG
4 ERA 8 TERM 8 TERM
8 CSA
9 ERB
6 CSB
Shell FG

GP-Pro EX Device/PLC Connection Manual 151

H Series Serial Driver

Cable Diagram 12

Display
Cable Remarks
(Connection Port)

GP (COM1) Your own cable

ST (COM1) + Cable length:
IPC*1 Conversion cable by Hitachi IES Co., Ltd. 15m or less
PC/AT EH-RS05(0.5m)
*1 Only the COM port which can communicate by RS-232C can be used.
) COM Port of IPC (page 8)

• When using the cable (EH-RS05) by Hitachi IES Co., Ltd.

Display Shield External Device

D-Sub 9 pin (socket) D-Sub 15 pin (plug)
External Device
Pin Signal name Pin Signal name RJ-45 conncetor
5 SG 9 SG EH-RS05
Display 2 RD(RXD) 2 SD
3 SD(TXD) 3 RD
6 DR(DSR) 7 DR
7 RS(RTS) 14 ER
8 CS(CTS) 4 RS
4 ER(DTR) 13 CS
Shell FG 11 CD

Your own cable

GP-Pro EX Device/PLC Connection Manual 152

H Series Serial Driver

Cable Diagram 13

Display
Cable Remarks
(Connection Port)

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
GP*1 (COM1) +
AGP-3302B (COM2) A Terminal block conversion adapter by Pro-face
ST*2 (COM2) CA3-ADPTRM-01
IPC*3 +
Your own cable

B Your own cable

Online adapter by Pro-face Cable length:

CA4-ADPONL-01 500m or less
+
C Terminal block conversion adapter by Pro-face
CA3-ADPTRM-01
GP*4 (COM2) +
Your own cable

Online adapter by Pro-face

GP-Pro EX Device/PLC Connection Manual 153

H Series Serial Driver

A. When using the COM port conversion adapter (CA3-ADPCOM-01), the terminal block conversion adapter
(CA3-ADPTRM-01) by Pro-face and your own cable
• 1:1 Connection
Display
Terminal block
External Device
Signal name Shield RJ-45 conncetor
TERM Pin Signal name
Display
RDA 3 TX
CA3-ADPCOM-01
RDB 5 TXN
SDA 7 RX
CA3-ADPTRM-01 SDB 6 RXN
SG 1 SG
FG

Your own cable

• 1:n Connection
Display
Terminal block
External Device External Device
Signal name Shield RJ-45 conncetor Shield RJ-45 conncetor
TERM Pin Signal name Pin Signal name
Display RDA 3 TX 3 TX
CA3-ADPCOM-01
RDB 5 TXN 5 TXN
SDA 7 RX 7 RX
CA3-ADPTRM-01 SDB 6 RXN 6 RXN
SG 1 SG 1 SG
FG

Your own cable

• Please turn on the DIP Switch 1 to enable build-in resistance(100Ω) on the remotest External
Device side.

GP-Pro EX Device/PLC Connection Manual 154

H Series Serial Driver

B. When your own cable is used

• 1:1 Connection

Display External Device

Terminal D-Sub 9 pin (socket) RJ-45 conncetor
resistance Shield
Pin Signal name Pin Signal name
100 Ω (1/2W)
1 RDA 3 TX
2 RDB 5 TXN
Display 3 SDA 7 RX
7 SDB 6 RXN
5 SG 1 SG
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG

• 1:n Connection
Display External Device External Device
D-Sub 9 pin (socket) RJ-45 conncetor RJ-45 conncetor
Terminal Shield Shield
resistance Pin Signal name Pin Signal name Pin Signal name
100 Ω (1/2W)
1 RDA 3 TX 3 TX
2 RDB 5 TXN 5 TXN
Display 3 SDA 7 RX 7 RX
7 SDB 6 RXN 6 RXN
5 SG 1 SG 1 SG
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG

• Please turn on the DIP Switch 1 to enable build-in resistance(100Ω) on the remotest External
Device side.

GP-Pro EX Device/PLC Connection Manual 155

H Series Serial Driver

C. When using the online adapter (CA4-ADPONL-01), the terminal block conversion adapter (CA3-ADPTRM-
01) by Pro-face and your own cable
• 1:1 Connection

Display
Terminal block
External Device
Signal name Shield RJ-45 conncetor
TERM Pin Signal name
Display RDA 3 TX
CA4-ADPONL-01
RDB 5 TXN
SDA 7 RX
CA3-ADPTRM-01 SDB 6 RXN
SG 1 SG
FG

Your own cable

• 1:n Connection
Display
Terminal block
External Device External Device
Signal name Shield RJ-45 conncetor Shield RJ-45 conncetor
TERM Pin Signal name Pin Signal name
Display RDA
CA4-ADPONL-01 3 TX 3 TX
RDB 5 TXN 5 TXN
SDA 7 RX 7 RX
CA3-ADPTRM-01 SDB 6 RXN 6 RXN
SG 1 SG 1 SG
FG

Your own cable

• Please turn on the DIP Switch 1 to enable build-in resistance(100Ω) on the remotest External
Device side.

GP-Pro EX Device/PLC Connection Manual 156

H Series Serial Driver

D. When using the online adapter (CA4-ADPONL-01) by Pro-face and your own cable
• 1:1 Connection
Display
D-Sub 9 pin (plug)
Shield External Device
Pin Signal name RJ-45 conncetor
CA4-ADPONL-01 1 TERMRX Pin Signal name
Display 2 RDA 3 TX
7 RDB 5 TXN
3 SDA 7 RX
8 SDB 6 RXN
5 SG 1 SG
9 TERMTX
Shell FG

Your own cable

• 1:n Connection
Display
D-Sub 9 pin (plug)
Shield External Device External Device
Pin Signal name RJ-45 conncetor RJ-45 conncetor
Shield
CA4-ADPONL-01 1 TERMRX Pin Signal name Pin Signal name
Display 2 RDA 3 TX 3 TX
7 RDB 5 TXN 5 TXN
3 SDA 7 RX 7 RX
8 SDB 6 RXN 6 RXN
5 SG 1 SG 1 SG
9 TERMTX
Shell FG

Your own cable

• Please turn on the DIP Switch 1 to enable build-in resistance(100Ω) on the remotest External
Device side.

GP-Pro EX Device/PLC Connection Manual 157

H Series Serial Driver

Cable Diagram 14

Display
Cable Remarks
(Connection Port)

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
+
GP*1 (COM1) A Terminal block conversion adapter by Pro-face
AGP-3302B (COM2) CA3-ADPTRM-01
ST*2 (COM2) +
Your own cable

B Your own cable

Online adapter by Pro-face

CA4-ADPONL-01
+
C Terminal block conversion adapter by Pro-face
CA3-ADPTRM-01
+ Cable length:
GP*3 (COM2)
Your own cable 500m or less

Online adapter by Pro-face

CA4-ADPONL-01
D
+
Your own cable

COM port conversion adapter by Pro-face

CA3-ADPCOM-01
+
E Terminal block conversion adapter by Pro-face
IPC*4 CA3-ADPTRM-01
+
Your own cable

F Your own cable

GP-Pro EX Device/PLC Connection Manual 158

H Series Serial Driver

A. When using the COM port conversion adapter (CA3-ADPCOM-01), the terminal block conversion adapter
(CA3-ADPTRM-01) by Pro-face and your own cable
• 1:1 Connection
Display
Terminal block
External Device
Signal name Shield RJ-45 conncetor
TERM Pin Signal name
Display RDA
CA3-ADPCOM-01 3 TX
RDB 5 TXN
SDA 7 RX
CA3-ADPTRM-01 SDB 6 RXN
SG 1 SG
FG

Your own cable

• 1:n Connection

Display
Terminal block
External Device External Device
Signal name Shield RJ-45 conncetor Shield RJ-45 conncetor
TERM Pin Signal name Pin Signal name
Display RDA
CA3-ADPCOM-01 3 TX 3 TX
RDB 5 TXN 5 TXN
SDA 7 RX 7 RX
CA3-ADPTRM-01 SDB 6 RXN 6 RXN
SG 1 SG 1 SG
FG

Your own cable

• Please turn on the DIP Switch 1 to enable build-in resistance(100Ω) on the remotest External
Device side.

GP-Pro EX Device/PLC Connection Manual 159

H Series Serial Driver

B. When your own cable is used

• 1:1 Connection

Display External Device

• 1:n Connection

Display External Device External Device

D-Sub 9 pin (socket) RJ-45 conncetor RJ-45 conncetor
Terminal Shield Shield
resistance Pin Signal name Pin Signal name Pin Signal name
100 Ω (1/2W)
1 RDA 3 TX 3 TX
2 RDB 5 TXN 5 TXN
Display 3 SDA 7 RX 7 RX
7 SDB 6 RXN 6 RXN
5 SG 1 SG 1 SG
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG

• Please turn on the DIP Switch 1 to enable build-in resistance(100Ω) on the remotest External
Device side.

GP-Pro EX Device/PLC Connection Manual 160

H Series Serial Driver

C. When using the online adapter (CA4-ADPONL-01), the terminal block conversion adapter (CA3-ADPTRM-
01) by Pro-face and your own cable
• 1:1 Connection
Display
Terminal block
External Device
Signal name Shield RJ-45 conncetor
TERM Pin Signal name
Display RDA
CA4-ADPONL-01 3 TX
RDB 5 TXN
SDA 7 RX
CA3-ADPTRM-01 SDB 6 RXN
SG 1 SG
FG

Your own cable

• 1:n Connection

Display
Terminal block
External Device External Device
Signal name Shield RJ-45 conncetor Shield RJ-45 conncetor
TERM Pin Signal name Pin Signal name
Display RDA 3 TX 3 TX
CA4-ADPONL-01
RDB 5 TXN 5 TXN
SDA 7 RX 7 RX
CA3-ADPTRM-01 SDB 6 RXN 6 RXN
SG 1 SG 1 SG
FG

Your own cable

• Please turn on the DIP Switch 1 to enable build-in resistance(100Ω) on the remotest External
Device side.

GP-Pro EX Device/PLC Connection Manual 161

H Series Serial Driver

D. When using the online adapter (CA4-ADPONL-01) by Pro-face and your own cable
• 1:1 Connection
Display
D-Sub 9 pin (plug)
External Device
Pin Signal name Shield RJ-45 conncetor
CA4-ADPONL-01 1 TERMRX Pin Signal name
Display 2 RDA 3 TX
7 RDB 5 TXN
3 SDA 7 RX
8 SDB 6 RXN
5 SG 1 SG
9 TERMTX
Shell FG

Your own cable

• 1:n Connection
Display
D-Sub 9 pin (plug)
External Device External Device
Pin Signal name Shield RJ-45 conncetor Shield RJ-45 conncetor
CA4-ADPONL-01 1 TERMRX Signal name Signal name
Pin Pin
Display 2 RDA 3 TX 3 TX
7 RDB 5 TXN 5 TXN
3 SDA 7 RX 7 RX
8 SDB 6 RXN 6 RXN
5 SG 1 SG 1 SG
9 TERMTX
Shell FG

Your own cable

• Please turn on the DIP Switch 1 to enable build-in resistance(100Ω) on the remotest External
Device side.

GP-Pro EX Device/PLC Connection Manual 162

H Series Serial Driver

E. When using the COM port conversion adapter (CA3-ADPCOM-01), the terminal block conversion adapter
(CA3-ADPTRM-01) by Pro-face and your own cable
• 1:1 Connection
Display
Terminal block
External Device
Signal name Shield RJ-45 conncetor
TERM Pin Signal name
Display RDA 3 TX
CA3-ADPCOM-01
RDB 5 TXN
SDA 7 RX
CA3-ADPTRM-01 SDB 6 RXN
SG 1 SG
FG

Your own cable

• 1:n Connection
Display
Terminal block
External Device External Device
Signal name Shield Shield
RJ-45 conncetor RJ-45 conncetor
TERM Pin Signal name Pin Signal name
Display RDA TX TX
CA3-ADPCOM-01 3 3
RDB 5 TXN 5 TXN
SDA 7 RX 7 RX
CA3-ADPTRM-01 SDB 6 RXN
6 RXN
SG 1 SG 1 SG
FG

Your own cable

• Please turn on the DIP Switch 1 to enable build-in resistance(100Ω) on the remotest External
Device side.

GP-Pro EX Device/PLC Connection Manual 163

H Series Serial Driver

F. When your own cable is used

• 1:1 Connection

Display External Device

Terminal D-Sub 9 pin (socket) RJ-45 conncetor
resistance Shield
100 Ω (1/2W) Pin Signal name Pin Signal name
1 DATA+ 3 TX
2 DATA- 5 TXN
Display 3 NC 7 RX
7 NC 6 RXN
5 GND(SG) 1 SG
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG

• 1:n Connection

Display External Device External Device

Terminal D-Sub 9 pin (socket) RJ-45 conncetor RJ-45 conncetor
resistance Shield Shield
100 Ω (1/2W) Pin Signal name Pin Signal name Pin Signal name
1 DATA+ 3 TX 3 TX
2 DATA- 5 TXN 5 TXN
Display 3 NC 7 RX 7 RX
7 NC 6 RXN 6 RXN
5 GND(SG) 1 SG 1 SG
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG

• Please turn on the DIP Switch 1 to enable build-in resistance(100Ω) on the remotest External
Device side.

GP-Pro EX Device/PLC Connection Manual 164

H Series Serial Driver

6 Supported Device

Range of supported device address is shown in the table below.

6.1 H/EH-150/MICRO-EH Series

This address can be specified as system data area.

Double Word
Device Bit Address Word Address 32 bits Remarks
Address

WX0000- *1 *2
External Input X00000-X05A95 DX0000-DX05A6
WX05A7

WY0000- *2
External Output Y00000-Y05A95 DY0000-DY05A6
WY05A7
*1 *3
Remote Input Relay X10000-X49995 WX1000-WX4997 DX1000-DX4996
*3
Remote Output Relay Y10000-Y49995 WY1000-WY4997 DY1000-DY4996

Internal Output R000-R7BF - -

Special Internal Output R7C0-R7FF - -

Data Area M0000-M3FFF WM000-WM3FF DM000-DM3FE

First CPU Link L00000-L03FFF WL0000-WL03FF DL0000-DL03FE

Second CPU Link L10000-L13FFF WL1000-WL13FF DL1000-DL13FE

On Delay Timer TD0000 -TD1023 - -

Single-shot Timer SS0000-SS1023 - -

WDT0000-
Watchdog Timer - -
WDT1023

Mono Stable Timer MS0000-MS1023 - -

TMR0000-
Retentive Timer - -
TMR1023

Up Counter CU0000-CU2047 - -

RCU0000-
Ring Counter - -
RCU2047

Up-down Counter CT0000-CT2047 - -

TM0000 -
Extended Timer - -
TM2047

Timer Counter
- TC0000-TC2047 -
(Elapsed Value)

Extended Timer
- TV0000 - TV2047 -
(Elapsed Value)

continued to next page

GP-Pro EX Device/PLC Connection Manual 165

H Series Serial Driver

Double Word
Device Bit Address Word Address 32 bits Remarks
Address

WR0000-
Word Internal Output - DR0000-DRC3FE
WRC3FF

Special Word Internal WRF000-

- DRF000-DRF1FE
Output WRF1FF

WN0000-
Network Link Area - DN0000-DN7FFE
WN7FFF

*1 Write disable
*2 Specify as shown below.
(Example) External input unit No.1, Slot No.2, Internal Module Bit No.34

X01234

Module Bit No. (00-95, decimal)

Slot No. (0-A, hexadecimal)
Unit No. (0-5)

(Example) External input unit No.1, Slot No.2, Internal Module Word No.34
WX0123

Module Word No.(0-7)

Slot No.(0-A, hexadecimal)
Unit No.(0-5)

*3 Specify as shown below.

(Example) Remote External Input Remote Master No.1, Remote Slave No.2, Slot No.3, Internal Module Bit
No.45
X12345

Module Bit No.(0-95)

Slot No.(0-9)
Remote Slave No.(0-9)
Remote Master No.(1-4)

(Example) Remote External Input Remote Master No.1, Remote Slave No.2, Slot No.3, Internal Module Word
No.4
WX1234

Module Word No.(0-7)

Slot No.(0-9)
Remote Slave No.(0-9)
Remote Master No.(1-4)

• Available type and range of device vary depending on CPU. Be sure to check them in each CPU
manual before using.

GP-Pro EX Device/PLC Connection Manual 166

H Series Serial Driver

How to set address when using the CPU link

Set the check box of "Use CPU Link" to ON.
When using CPU Link, loop No. and unit No. are added to the address.

(Example) Loop No.1, Unit No.2

1/ 2/ WR0000

Device Address
CPU Link Unit No.
CPU Link Loop No.

• Please refer to the GP-Pro EX Reference Manual for system data area.

Cf. GP-Pro EXReference Manual "Appendix 1.4 LS Area (Direct Access Method)"

• Please refer to the precautions on manual notation for icons in the table.
) "Manual Symbols and Terminology"

GP-Pro EX Device/PLC Connection Manual 167

H Series Serial Driver

6.2 Web Controller Series

This address can be specified as system data area.

Double Word
Device Bit Address Word Address 32 bit Remarks
Address

X0000-X0012 WX030-WX031 DX030

X1000-X1015 WX100-WX104 DX100-DX103
*1
External Input X2000-X2015 WX200-WX204 DX200-DX203
X3000-X3015 WX300-WX304 DX300-DX303
X4000-X4015 WX400-WX404 DX400-DX403

Y0100-Y0109 WY40
DY105-DY106
Y1016-Y1031 WY105-WY107
DY205-DY206
External Output Y2016-Y2031 WY205-WY207
DY305-DY306
Y3016-Y3031 WY305-WY307
DY405-DY406
Y4016-Y4031 WY405-WY407

Internal Output R000-R7BF - -

Special Internal Output R7C0-R7FF - -

Data Area M0000-M3FFF WM000-WM3FF DM000-DM3FE

*2
On Delay Timer TD000-TD255 - -
*2
Single-shot Timer SS000-SS255 - -
*2
Up Counter CU000-CU255 - -
*2*3
Up-down Counter CT000-CT255 - -

Timer Counter
- TC000-TC255 -
(Elapsed Value)

WR0000- *4
Word Internal Output - DR0000-DRC3FE
WRC3FF

Word Special Internal WRF000-

DRF000-DRF1FE
Output WRF1FF

*1 Write disable
*2 Each timer or counter needs to be defined on the ladder program.
*3 Both the Up-down counter Up input and Down input are defined by CT, however, the device names of the
External Device are CTU, CTDrespectively.
To access CTU, define the corresponding address as CTU on the ladder program of the External Device.
Similarly, to access CTD, define the corresponding address as CTD on the ladder program of the External
Device.
*4 In case of EH-WD10DR, the address range is "WR0000-WR3FFF", "DR0000-DR3FFE".

• Please refer to the GP-Pro EX Reference Manual for system data area.

Cf. GP-Pro EXReference Manual "Appendix 1.4 LS Area (Direct Access Method)"

• Please refer to the precautions on manual notation for icons in the table.
) "Manual Symbols and Terminology"

GP-Pro EX Device/PLC Connection Manual 168

H Series Serial Driver

6.3 EHV Series

This address can be specified as system data area.

Double Word
Device Bit Address Word Address 32 bits Remarks
Address

WX0000- *1 *2
External Input X00000-X05A95 DX0000-DX05A6
WX05A7

WY0000- *2
External Output Y00000-Y05A95 DY0000-DY05A6
WY05A7

WX1000- *1 *3
Remote Input Relay X10000-X45A95 DX1000-DX45A6
WX45A7

WY1000- *3
Remote Output Relay Y10000-Y45A95 DY1000-DY45A6
WY45A7

EX00000- WEX0000- DEX0000- *1

Extension External Input
EX5A7FF WEX5A7F DEX5A7E

EY00000- WEY0000- DEY0000-

Extension External Output
EY5A7FF WEY5A7F DEY5A7E

Internal Output R000-R7BF - -

Special Internal Output R7C0-RFFF - -

WM0000- DM0000-
Data Area M00000-M7FFFF
WM7FFF DM7FFE

First CPU Link L00000-L03FFF WL0000-WL03FF DL0000-DL03FE

Second CPU Link L10000-L13FFF WL1000-WL13FF DL1000-DL13FE

Third CPU Link L20000-L23FFF WL2000-WL23FF DL2000-DL23FE

Fourth CPU Link L30000-L33FFF WL3000-WL33FF DL3000-DL33FE

Fifth CPU Link L40000-L43FFF WL4000-WL43FF DL4000-DL43FE

Sixth CPU Link L50000-L53FFF WL5000-WL53FF DL5000-DL53FE

Seventh CPU Link L60000-L63FFF WL6000-WL63FF DL6000-DL63FE

Eighth CPU Link L70000-L73FFF WL7000-WL73FF DL7000-DL73FE

On Delay Timer TD0000-TD2559 - -

TDN0000-
Off Delay Timer - -
TDN2559

Single-shot Timer SS0000-SS2559 - -

WDT0000-
Watchdog Timer - -
WDT2559

Mono Stable Timer MS0000-MS2559 - -

TMR0000-
Retentive Timer - -
TMR2559

Up-down Counter CT000-CT511 - -

Up Counter CU000-CU511 - -

GP-Pro EX Device/PLC Connection Manual 169

H Series Serial Driver

Double Word
Device Bit Address Word Address 32 bits Remarks
Address

Link Counter RCU000-RCU511 - -

Timer Counter
- TC0000-TC2559 -
(Elapsed Value)

WR00000- WR0000-
Word Internal Output DR0000-DREFFE
WREFFFF WREFFF

Special Word Internal WRF000.0- WRF000-

DRF000-DRFFFE
Output WRFFFF.F WRFFFF

WN00000.0- WN00000- DN00000-

Data Area
WN1FFFF.F WN1FFFF DN1FFFE

*1 Write disable
*2 Specify as shown below.
(Example) External input unit No.1, Slot No.2, Internal Module Bit No.34
X01234

Module Bit No.(00-95, decimal)

Slot No.(0-A, hexadecimal)
Unit No.(0-5)

(Example) External input unit No.1, Slot No.2, Internal Module Word No.3

WX0123

Module Word No.(0-7)

Slot No.(0-A, hexadecimal)
Unit No.(0-5)

*3 Specify as shown below.

(Example) Remote External Input Remote Master No.1, Remote Slave No.2, Slot No.3, Internal Module Bit
No.45
X12345

Module Bit No.(0-95, decimal)

Slot No.(0-A, hexadecimal)
Remote Slave No.(0-5)
Remote Master No.(1-4)

(Example) Remote External Input Remote Master No.1, Remote Slave No.2, Slot No.3, Internal Module Word
No.4
WX1234

Module Word No.(0-7)

Slot No.(0-A, hexadecimal)
Remote Slave No.(0-5)
Remote Master No.(1-4)

GP-Pro EX Device/PLC Connection Manual 170

H Series Serial Driver

When using CPU Link

Set the check box of "Use CPU Link" to ON.
When using CPU Link, loop No. and unit No. are added to the address.

(Example) Loop No.1, Unit No.2

1/ 2/ WR0000

Device Address
CPU Link Unit No.
CPU Link Loop No.

• Please refer to the GP-Pro EX Reference Manual for system data area.

Cf. GP-Pro EXReference Manual "Appendix 1.4 LS Area (Direct Access Method)"

• Please refer to the precautions on manual notation for icons in the table.
) "Manual Symbols and Terminology"

GP-Pro EX Device/PLC Connection Manual 171

H Series Serial Driver

7 Device Code and Address Code

Use device code and address code when you select "Device Type & Address" for the address type in data displays.

7.1 H/EH-150/MICRO-EH Series

Device Code
Device Device Name Address Code
(HEX)

X Word Address
80
External Input WX Word Address

DX 20 Word Address

Y Word Address
81
External Output WY Word Address

DY 21 Word Address

M Word Address
82
Data Area WM Word Address

DM 22 Word Address

L Word Address
83
CPU Link WL Word Address

DL 23 Word Address

Timer Counter
TC 60 Word Address
(Elapsed Value)

Extended Timer
TV 61 Word Address
(Elapsed Value)

WR 00 Word Address
Word Internal Output
DR 24 Word Address

WN 01 Word Address
Network Link Area
DN 25 Word Address

GP-Pro EX Device/PLC Connection Manual 172

H Series Serial Driver

7.2 Web Controller Series

Device Code
Device Device Name Address Code
(HEX)

X Word Address
80
External Input WX Word Address

DX 20 Word Address

Y Word Address
81
External Output WY Word Address

DY 21 Word Address

M Word Address
82
Data Area WM Word Address

DM 22 Word Address

Timer Counter (Elapsed Value) TC 60 Word Address

Word Internal Output WR 00 Word Address

Word Special Internal Output DR 24 Word Address

GP-Pro EX Device/PLC Connection Manual 173

H Series Serial Driver

7.3 EHV Series

Device Code
Device Device Name Address Code
(HEX)

X Word Address
80
External Input WX Word Address

DX 20 Word Address

Y Word Address
81
External Output WY Word Address

DY 21 Word Address

EX Word Address
84
Extension External Input WEX Word Address

DEX 26 Word Address

EY Word Address
85
Extension External Output WEY Word Address

DEY 27 Word Address

M Word Address
82
Data Area WM Word Address

DM 22 Word Address

L Word Address
83
CPU Link WL Word Address

DL 23 Word Address

WR 00 Word Address
Word Internal Output
DR 24 Word Address

WN 01 Word Address
Data Area
DN 25 Word Address

Timer Counter
TC 60 Word Address
(Elapsed Value)

GP-Pro EX Device/PLC Connection Manual 174

H Series Serial Driver

8 Error Messages

Error messages are displayed on the screen of the Display as follows: "No. :Device Name:Error Message(Error
Occurrence Area)". Each description is shown below.

Item Description
No. Error No.
Name of the External Device where error occurs. Device name is a title of the External
Device Name
Device set with GP-Pro EX.((Initial value[PLC1])
Error Message Displays messages related to the error which occurs.
Displays IP address or device address of the External Device where error occurs, or error
codes received from the External Device.

Error Occurrence Area

• IP address is displayed such as "IP address(Decimal): MAC address( Hex)".
• Device address is displayed such as "Address: Device address".
• Received error codes are displayed such as "Hex[Hex]".

Display Examples of Error Messages

"RHAA035:PLC1: Error has been responded for device write command (Error Code: [02H,02H])"

• Refer to your External Device manual for details on received error codes.
• Refer to "When an error is displayed (Error Code List)" in "Maintenance/Troubleshooting Manual"
for details on the error messages common to the driver.

Driver-Specific Error Codes

Error codes are sent as separated 2 bytes codes The Display displays the error number using 1-byte code.
Example:
Reply command Return code Error display
01 07 01 07

Error Code Description

01, 05 The requested number of points is beyond the designated range.
01, 06 Designated device does not exist.
01, 07 Designated device address is beyond the range.

• Please refer to the manual of the External Device for more detail of received error codes.

GP-Pro EX Device/PLC Connection Manual 175

H Series Serial Driver

GP-Pro EX Device/PLC Connection Manual 176

MICREX-F Series SIO Driver
No ratings yet
MICREX-F Series SIO Driver
44 pages
EX100 Computer Link Manual - 514
No ratings yet
EX100 Computer Link Manual - 514
70 pages
Mod Grs
No ratings yet
Mod Grs
118 pages
Hie Hsio
No ratings yet
Hie Hsio
196 pages
Hie Mods
No ratings yet
Hie Mods
53 pages
Mitqacpu
No ratings yet
Mitqacpu
22 pages
Mat Mews
No ratings yet
Mat Mews
134 pages
Mod Slav
No ratings yet
Mod Slav
58 pages
FX Series Computer Link Driver
No ratings yet
FX Series Computer Link Driver
60 pages
tsmtc200 2
No ratings yet
tsmtc200 2
75 pages
Roc - Etip 2
No ratings yet
Roc - Etip 2
92 pages
Ytk Cpls
No ratings yet
Ytk Cpls
258 pages
Mit - Acpu (1) Driver Passthroght
No ratings yet
Mit - Acpu (1) Driver Passthroght
32 pages
Gef SNPX
No ratings yet
Gef SNPX
40 pages
Fuj Fsio
No ratings yet
Fuj Fsio
50 pages
KV-700/1000/3000/5000 CPU Direct
No ratings yet
KV-700/1000/3000/5000 CPU Direct
56 pages
Proface I
No ratings yet
Proface I
19 pages
Tos Lsio
No ratings yet
Tos Lsio
74 pages
FACON Serial Driver
No ratings yet
FACON Serial Driver
66 pages
Fuji PLC Comunicacion
100% (1)
Fuji PLC Comunicacion
37 pages
Cables y Comunicacion
No ratings yet
Cables y Comunicacion
58 pages
SR23 Series Controller Instruction Manual (Detailed Version)
No ratings yet
SR23 Series Controller Instruction Manual (Detailed Version)
68 pages
Fanuc PM PDF
No ratings yet
Fanuc PM PDF
42 pages
Saia Sio
No ratings yet
Saia Sio
58 pages
Mitfxcpu PDF
No ratings yet
Mitfxcpu PDF
58 pages
SHKTC CN
No ratings yet
SHKTC CN
108 pages
Mitfxcpu
No ratings yet
Mitfxcpu
50 pages
Gef SNPX
No ratings yet
Gef SNPX
64 pages
Tioga Pipe Chart
No ratings yet
Tioga Pipe Chart
2 pages
modusAddressTCPMaster PDF
No ratings yet
modusAddressTCPMaster PDF
30 pages
ASCII Protocol Communication Manual
No ratings yet
ASCII Protocol Communication Manual
56 pages
LG MKCNT
No ratings yet
LG MKCNT
72 pages
HITACHI
No ratings yet
HITACHI
5 pages
Mit Alnk
No ratings yet
Mit Alnk
62 pages
Manual IHM
No ratings yet
Manual IHM
70 pages
General MODBUS TCP Master Driver
No ratings yet
General MODBUS TCP Master Driver
28 pages
Computer Link Ethernet Driver
No ratings yet
Computer Link Ethernet Driver
30 pages
Mit QMC
No ratings yet
Mit QMC
100 pages
Shihlin Ekran Haberleşme MITSUBISHI en
No ratings yet
Shihlin Ekran Haberleşme MITSUBISHI en
10 pages
MANUAL MILENIUM 3 - cstcrzm3
No ratings yet
MANUAL MILENIUM 3 - cstcrzm3
18 pages
Ytk Cpls PDF
No ratings yet
Ytk Cpls PDF
156 pages
Ls GMCNT
No ratings yet
Ls GMCNT
45 pages
Leadshine EL5 User Manual
No ratings yet
Leadshine EL5 User Manual
97 pages
Iec 60870 101 PDF
100% (2)
Iec 60870 101 PDF
34 pages
Saia Sio
No ratings yet
Saia Sio
50 pages
Manual
No ratings yet
Manual
5 pages
Solenoid Valve
No ratings yet
Solenoid Valve
16 pages
Simatic S5 Cpu Direct Driver
No ratings yet
Simatic S5 Cpu Direct Driver
16 pages
Hitachi Seiki VS50 60 Operating Manual
100% (1)
Hitachi Seiki VS50 60 Operating Manual
139 pages
Hitachi EH Series PLC - EN
No ratings yet
Hitachi EH Series PLC - EN
6 pages
Alarm List For Mazatrol M32
100% (1)
Alarm List For Mazatrol M32
122 pages
Fanuc Oi-MF Datasheet
No ratings yet
Fanuc Oi-MF Datasheet
2 pages
Ethernet Switch/Router L2/L3/MPLS 12x10G User Guide: Packet Architects AB
No ratings yet
Ethernet Switch/Router L2/L3/MPLS 12x10G User Guide: Packet Architects AB
221 pages
Mazak Fusion 640 Series How To Create A Backup Using RS232
100% (3)
Mazak Fusion 640 Series How To Create A Backup Using RS232
5 pages
Fuji Frenic 5000M2 Instruction Manual
No ratings yet
Fuji Frenic 5000M2 Instruction Manual
9 pages
GP-PRO/PBIII For Windows Device/Plc Connection Manual
No ratings yet
GP-PRO/PBIII For Windows Device/Plc Connection Manual
46 pages
Codesys Sio Driver
No ratings yet
Codesys Sio Driver
25 pages
Pipe Dimensions Chart Rev Jan 2012
No ratings yet
Pipe Dimensions Chart Rev Jan 2012
1 page
User'S Guide: Fx-232Adp Communication Adapter
No ratings yet
User'S Guide: Fx-232Adp Communication Adapter
12 pages
Toshiba T Series
No ratings yet
Toshiba T Series
4 pages
Unitelway
No ratings yet
Unitelway
56 pages
SASE For Dummies®, Versa Networks Special Edition by Kumar Mehta Apurva Mehta
100% (1)
SASE For Dummies®, Versa Networks Special Edition by Kumar Mehta Apurva Mehta
79 pages
Hitachi H Series
No ratings yet
Hitachi H Series
3 pages
HITACHI H Series (CPU Port) : HMI Setting
No ratings yet
HITACHI H Series (CPU Port) : HMI Setting
4 pages
Sicam Sat 1703 Acp - Rtu PDF
100% (2)
Sicam Sat 1703 Acp - Rtu PDF
12 pages
Hhi Hi5s
No ratings yet
Hhi Hi5s
36 pages
About The Device/PLC Connection Manuals
No ratings yet
About The Device/PLC Connection Manuals
7 pages
Communication Interface: EM70 Servo Controller
No ratings yet
Communication Interface: EM70 Servo Controller
16 pages
VPI-VSI Communications Manual
No ratings yet
VPI-VSI Communications Manual
39 pages
HJ AC Servo Motor Technical Data Manual Issue 5.5
100% (1)
HJ AC Servo Motor Technical Data Manual Issue 5.5
144 pages
Communication Interface: SR90 Series Digital Controller
No ratings yet
Communication Interface: SR90 Series Digital Controller
16 pages
KG316T Time Switch Manual
No ratings yet
KG316T Time Switch Manual
4 pages
VX-410/-420 Series: Service Manual UHF FM Transceiver
No ratings yet
VX-410/-420 Series: Service Manual UHF FM Transceiver
45 pages
MR Series Rectangular Connectors
No ratings yet
MR Series Rectangular Connectors
69 pages
RF 7800S TR DataSheet Tcm26 13806
100% (1)
RF 7800S TR DataSheet Tcm26 13806
2 pages
AC Axial Fan
No ratings yet
AC Axial Fan
20 pages
Yamaichi FA Series
No ratings yet
Yamaichi FA Series
3 pages
Panasonic KX-TA624 User Manual
No ratings yet
Panasonic KX-TA624 User Manual
16 pages
DAC80 CB1 V Datasheet
No ratings yet
DAC80 CB1 V Datasheet
10 pages
Drill 6411-6412-6413 Instruction Manual
No ratings yet
Drill 6411-6412-6413 Instruction Manual
8 pages
HDSD Kbone
No ratings yet
HDSD Kbone
8 pages
GSM Shield Datasheet Arduino Tutorial
100% (3)
GSM Shield Datasheet Arduino Tutorial
10 pages
UsersGuide 20S EVO 1.3.0 en 211102
No ratings yet
UsersGuide 20S EVO 1.3.0 en 211102
53 pages
Ckd-Filter w1000 Series
No ratings yet
Ckd-Filter w1000 Series
5 pages
PPT ch01
No ratings yet
PPT ch01
48 pages
EVOLIUM A9100 Base Station Product Description
100% (1)
EVOLIUM A9100 Base Station Product Description
77 pages
Panasonic KX-TA624 Installation Manual
100% (1)
Panasonic KX-TA624 Installation Manual
12 pages
Pneumatic Regulators R07 Datasheet
No ratings yet
Pneumatic Regulators R07 Datasheet
3 pages
Amplification Ndss2014
No ratings yet
Amplification Ndss2014
15 pages
HSC ICT 2nd Lesson MCQ
No ratings yet
HSC ICT 2nd Lesson MCQ
1 page
DIY SMS Gateway - Send Messages Anytime, Anywhere
No ratings yet
DIY SMS Gateway - Send Messages Anytime, Anywhere
27 pages
Lecture 6
No ratings yet
Lecture 6
13 pages
DCUG EIGRP Class-2006-12-14
No ratings yet
DCUG EIGRP Class-2006-12-14
52 pages
Wireless System: Online User Guide For Shure BLX Wireless System. Version: 4 (2019-H)
No ratings yet
Wireless System: Online User Guide For Shure BLX Wireless System. Version: 4 (2019-H)
28 pages
U - TM - ZXUR 9000 UMTS Radio Network Controller - OMM & Logservice Installation - R2.1
No ratings yet
U - TM - ZXUR 9000 UMTS Radio Network Controller - OMM & Logservice Installation - R2.1
30 pages
8.2.4.13 Packet Tracer - Troubleshooting Enterprise Networks 2 Instructions
No ratings yet
8.2.4.13 Packet Tracer - Troubleshooting Enterprise Networks 2 Instructions
4 pages
Defi Important Questions of Computer Class
No ratings yet
Defi Important Questions of Computer Class
3 pages
Pulse-Density Modulation For RF Applications: The Radio-Frequency Power Amplifier (RF PA) As A Power Converter
No ratings yet
Pulse-Density Modulation For RF Applications: The Radio-Frequency Power Amplifier (RF PA) As A Power Converter
6 pages
tm111 Summry
100% (1)
tm111 Summry
9 pages
Lab - Build A Hub, Switch, and Router Network Topology:: Background / Scenario
No ratings yet
Lab - Build A Hub, Switch, and Router Network Topology:: Background / Scenario
8 pages
Understanding The Pre-Emphasis and Linear Equalization Features in Stratix IV GX Devices
No ratings yet
Understanding The Pre-Emphasis and Linear Equalization Features in Stratix IV GX Devices
16 pages
Network Attacks Taxonomy Tools and Systems
No ratings yet
Network Attacks Taxonomy Tools and Systems
18 pages
Super 25 NIS Questions V2V
No ratings yet
Super 25 NIS Questions V2V
3 pages
Abdul Rahman PGP Trust
No ratings yet
Abdul Rahman PGP Trust
5 pages
Synchronous Modems: Synchronous Data Phase Modulation Integrated Phase and Amplitude
No ratings yet
Synchronous Modems: Synchronous Data Phase Modulation Integrated Phase and Amplitude
6 pages
1783ETAP
No ratings yet
1783ETAP
2 pages
Chapter 8 Test CS2 1
No ratings yet
Chapter 8 Test CS2 1
5 pages
The Cell Phone: Diana Valentina Guerra Ochoa T00040791
No ratings yet
The Cell Phone: Diana Valentina Guerra Ochoa T00040791
4 pages
Fibre Channel (Arinc 818) MIL-STD-1553B ARINC 429 Can-Bus Ethernet
No ratings yet
Fibre Channel (Arinc 818) MIL-STD-1553B ARINC 429 Can-Bus Ethernet
2 pages
PLC: Programmable Logic Controller – Arktika.: EXPERIMENTAL PRODUCT BASED ON CPLD.
From Everand
PLC: Programmable Logic Controller – Arktika.: EXPERIMENTAL PRODUCT BASED ON CPLD.
Franco Mario
No ratings yet
CompTIA A+ CertMike: Prepare. Practice. Pass the Test! Get Certified!: Core 1 Exam 220-1101
From Everand
CompTIA A+ CertMike: Prepare. Practice. Pass the Test! Get Certified!: Core 1 Exam 220-1101
Mike Chapple
No ratings yet

H Series Serial Driver

Uploaded by

H Series Serial Driver

Uploaded by

Hitachi IES Co., Ltd.

H Series Serial Driver

2 Selection of External Device

3 Example of Communication Settings

GP-Pro EX Device/PLC Connection Manual 2

H-200(CPU-02H)*1 Setting Cable

H-300(CPU-03Ha) Setting Cable

GP-Pro EX Device/PLC Connection Manual 3

EH-150(EH-CPU308A) Setting Cable

GP-Pro EX Device/PLC Connection Manual 4

MICRO-EH(EH-D10)*5 Setting Cable

MICRO-EH(EH-A64)*5 Setting Cable

GP-Pro EX Device/PLC Connection Manual 5

MICRO-EH(EH-D10)*5 Setting Cable

MICRO-EH(EH-A64)*5 Setting Cable

GP-Pro EX Device/PLC Connection Manual 6

*1 Connect to the peripheral port on the CPU module.

GP-Pro EX Device/PLC Connection Manual 7

 COM Port of IPC

Dip switch setting: RS-232C

Dip switch Setting Description

GP-Pro EX Device/PLC Connection Manual 8

Dip switch setting: RS-422/485 (4 wire)

Dip switch Setting Description

Dip switch setting: RS-422/485 (2 wire)

Dip switch Setting Description

GP-Pro EX Device/PLC Connection Manual 9

2 Selection of External Device

Select the External Device to be connected to the Display.

Setup Items Setup Description

Cf. Maintenance/Troubleshooting "2.15.1 Settings common to all Display

GP-Pro EX Device/PLC Connection Manual 10

3 Example of Communication Setting

3.1 Setting Example 1

GP-Pro EX Device/PLC Connection Manual 11

 Settings of External Device (Port on the CPU unit: H-4010 only)

 Mode Setting Switch

• Other transmission speed settings are shown below.

DIP Switch Settings Description

GP-Pro EX Device/PLC Connection Manual 12

3.2 Setting Example 2

GP-Pro EX Device/PLC Connection Manual 13

 Settings of External Device(COMM-H, COMM-2H)

 Communication Setting Switch

 Station Setting Rotary Switch

 Mode Setting Rotary Switch

GP-Pro EX Device/PLC Connection Manual 14

3.3 Setting Example 3

GP-Pro EX Device/PLC Connection Manual 15

 Settings of External Device (COMM-H, COMM-2H)

 Communication Setting Switch

 Station Setting Rotary Switch

 Mode Setting Rotary Switch

GP-Pro EX Device/PLC Connection Manual 16

3.4 Setting Example 4

GP-Pro EX Device/PLC Connection Manual 17

 Settings of External Device (COMM-2H)

 Communication Setting Switch

 Station Setting Rotary Switch

 Mode Setting Rotary Switch

GP-Pro EX Device/PLC Connection Manual 18

3.5 Setting Example 5

GP-Pro EX Device/PLC Connection Manual 19

 Settings of External Device (COMM-2H)

 Communication Setting Switch

 Station Setting Rotary Switch

 Mode Setting Rotary Switch

GP-Pro EX Device/PLC Connection Manual 20

3.6 Setting Example 6

GP-Pro EX Device/PLC Connection Manual 21

 Settings of External Device (Serial port on the CPU unit)

 Mode Setting Switch

 Port Change Switch

• When the change switch is ON, PHL signal becomes High(ON).

GP-Pro EX Device/PLC Connection Manual 22

3.7 Setting Example 7

MICRO-EH(EH-D10)*5 Setting Cable

MICRO-EH(EH-A64)*5 Setting Cable

MICRO-EH(EH-D10)*5 Setting Cable

MICRO-EH(EH-A64)*5 Setting Cable

COM Port of IPC

Settings of External Device (Port on the CPU unit: H-4010 only)

Mode Setting Switch

Settings of External Device(COMM-H, COMM-2H)

Communication Setting Switch

Station Setting Rotary Switch

Mode Setting Rotary Switch

Settings of External Device (COMM-H, COMM-2H)

Communication Setting Switch

Station Setting Rotary Switch

Mode Setting Rotary Switch

Settings of External Device (COMM-2H)

Communication Setting Switch

Station Setting Rotary Switch

Mode Setting Rotary Switch

Settings of External Device (COMM-2H)

Communication Setting Switch

Station Setting Rotary Switch

Mode Setting Rotary Switch

Settings of External Device (Serial port on the CPU unit)

Mode Setting Switch

Port Change Switch

Settings of External Device (Serial port on the CPU unit)

Settings of External Device (Serial port on the CPU unit)

Settings of External Device (EH-SIO)

Settings of External Device (EH-SIO)

Settings of External Device (EH-SIO)

Settings of External Device (EH-SIO)

Settings of External Device (Serial port on the CPU unit)

Mode Setting Switch

Settings of External Device (Serial port on the CPU unit)

Settings of External Device (Serial port on the CPU unit)

Settings of External Device (EH-SIO)

Settings of External Device (EH-SIO)

Settings of External Device (EH-SIO)

Settings of External Device (EH-SIO)

Settings of External Device (Port on the CPU unit)

Settings of External Device (Port on the CPU unit)