0% found this document useful (0 votes)
326 views5 pages

Zytel HTN52 G35 HSL

PLASTIC

Uploaded by

Visan Gheorghe
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
326 views5 pages

Zytel HTN52 G35 HSL

PLASTIC

Uploaded by

Visan Gheorghe
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Product Information

™ ®
DuPont™ Zytel® HTN
high performance polyamide resin
PRELIMINARY DATA
Zytel HTN52G35HSL NC010
®

Zytel® HTN52G35HSL NC010 is a 35% glass reinforced, heat stabilized, lubricated high performance polyamide
resin that can be molded in water heated molds.
Value
Property Test Method Units
DAM 50%RH
Identification
Part Marking Code ISO 11469 >PA6T/66-GF35<
Part Marking Code SAE J1344 >PPA-GF35<
Mechanical
Stress at Break ISO 527 MPa (kpsi) 200 (29) 180 (26)
Strain at Break ISO 527 % 2.1 2.7
Tensile Modulus ISO 527 MPa (kpsi) 12500 (1813) 12000 (1740)
Shear Strength ASTM D 732 MPa (kpsi) 91.7 (13.3) 79.3 (11.5)
Flexural Modulus ASTM D 790 MPa (kpsi) 10190 (1480) 8300 (1220)
Flexural Strength ASTM D 790 MPa (kpsi) 299 (43.4) 249 (36.1)
Compressive Strength ASTM D 695 MPa (kpsi) 281 (40.8)
Compressive Modulus ASTM D 695 MPa (kpsi) 5030 (730)
Izod Impact ASTM D 256 J/m (ft lb/in)
-40°C (-40°F) 91 (1.7) 91 (1.7)
2
Unnotched Izod Impact Strength ISO 180/1U kJ/m 40 45
Unnotched Charpy Impact Strength ISO 179/1eU kJ/m2 45 40
Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.
ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.
Test temperatures are 23°C unless otherwise stated.

During molding, use proper protective equipment and adequate ventilation. Avoid exposure to fumes and limit the
hold up time and temperature of the resin in the machine. Purge degraded resin carefully with HDPE.

The above data are preliminary and are subject to change as additional data are developed on subsequent lots.

The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2007.
070830/070905
The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new
knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these
data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.
The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you
may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations
in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this
publication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent
counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical
application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont under
a written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information,
please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-2 and
DuPont CAUTION Regarding Medical Applications … H-50102-2.

plastics.dupont.com

1/5
Product Information

Zytel HTN52G35HSL NC010


®

Value
Property Test Method Units
DAM 50%RH
Thermal
Deflection Temperature ISO 75-1/-2 °C (°F)
1.80MPa 285 (545)
Melting Temperature ISO 11357-1/-3 °C (°F)
10°C/min, First Heat 305 (581)
CLTE, Parallel ISO 11359-1/-2 E-4/C (E-4/F)
-40 - 23°C (-40 - 73°F) 0.2 (0.11)
23 - 55°C (73 - 130°F) 0.21 (0.12)
55 - 125°C (131 - 257°F) 0.15 (0.08)
125 - 200°C (257 - 392°F) 0.13 (0.07)
CLTE, Parallel ASTM E 831 E-4/C (E-4/F)
-40 - 23°C (-40 - 73°F) 0.2 (0.11)
23 - 55°C (73 - 130°F) 0.21 (0.12)
55 - 125°C (131 - 257°F) 0.15 (0.08)
125 - 200°C (257 - 392°F) 0.13 (0.07)
CLTE, Normal ISO 11359-1/-2 E-4/C (E-4/F)
-40 - 23°C (-40 - 73°F) 0.57 (0.32)
23 - 55°C (73 - 130°F) 0.62 (0.35)
55 - 125°C (131 - 257°F) 0.77 (0.43)
125 - 200°C (257 - 392°F) 0.95 (0.53)
Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.
ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.
Test temperatures are 23°C unless otherwise stated.

The above data are preliminary and are subject to change as additional data are developed on subsequent lots.

The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2007.
070830/070905
The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new
knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these
data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.
The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you
may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations
in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this
publication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent
counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical
application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont under
a written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information,
please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-2 and
DuPont CAUTION Regarding Medical Applications … H-50102-2.

plastics.dupont.com

2/5
Product Information

Zytel HTN52G35HSL NC010


®

Value
Property Test Method Units
DAM 50%RH
Electrical
Surface Resistivity ASTM D 257 ohm 1E15
Volume Resistivity ASTM D 257 ohm cm 1E15
Dielectric Strength, Short Time ASTM D 149 kV/mm (V/mil)
3.2mm (0.125in) 27.5 (700)
Dielectric Constant ASTM D 150
1E3 Hz 3.9
1E6 Hz 3.8
Dissipation Factor ASTM D 150
1E3 Hz 0.01
1E6 Hz 0.01
Arc Resistance ASTM D 495 s 117
CTI IEC 60112 V 600
CTI M IEC 60112 V 325
Flammability
Flammability Classification UL94
0.75mm HB
Oxygen Index ASTM D 2863 % 25
Glow Wire Flammability Index IEC 60695-2-12 °C
0.75mm 750
1.5mm 700
3.0mm 850
Glow Wire Ignition Temperature IEC 60695-2-13 °C
0.75mm 775
1.5mm 725
3.0mm 775
Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.
ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.
Test temperatures are 23°C unless otherwise stated.

The above data are preliminary and are subject to change as additional data are developed on subsequent lots.

The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2007.
070830/070905
The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new
knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these
data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.
The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you
may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations
in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this
publication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent
counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical
application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont under
a written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information,
please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-2 and
DuPont CAUTION Regarding Medical Applications … H-50102-2.

plastics.dupont.com

3/5
Product Information

Zytel HTN52G35HSL NC010


®

Value
Property Test Method Units
DAM 50%RH
Flammability
High Amperage Arc Ignition Resistance UL 746A arcs
1.5mm 150
3.0mm 150
Hot Wire Ignition UL 746A s
1.5mm 150
3.0mm 150
Temperature Index
RTI, Electrical UL 746B °C
0.75mm 65
1.5mm 65
3.0mm 65
RTI, Impact UL 746B °C
0.75mm 65
1.5mm 65
3.0mm 65
RTI, Strength UL 746B °C
0.75mm 65
1.5mm 65
3.0mm 65
Other
Density ISO 1183 kg/m3 (g/cm3) 1450 (1.45)
Hardness, Rockwell ASTM D 785
Scale M 105
Scale R 124
Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.
ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.
Test temperatures are 23°C unless otherwise stated.

The above data are preliminary and are subject to change as additional data are developed on subsequent lots.

The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2007.
070830/070905
The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new
knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these
data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.
The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you
may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations
in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this
publication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent
counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical
application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont under
a written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information,
please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-2 and
DuPont CAUTION Regarding Medical Applications … H-50102-2.

plastics.dupont.com

4/5
Product Information

Zytel HTN52G35HSL NC010


®

Value
Property Test Method Units
DAM 50%RH
Other
Water Absorption ISO 62, Similar to %
Equilibrium 50%RH, 1.0mm 2
Saturation, immersed, 1.0mm 4.5
Mold Shrinkage %
Flow, 1.6mm (0.062in) 0.25
Flow, 3.2mm (0.125in) 0.3
Transverse, 1.6mm (0.062in) 1.0
Transverse, 3.2mm (0.125in) 1.0
Processing
Melt Temperature Range °C (°F) 320-330 (610-625)
Melt Temperature Optimum °C (°F) 325 (620)
Mold Temperature Range °C (°F) 85-105 (190-220)
Mold Temperature Optimum °C (°F) 95 (200)
Injection Speed s Fast
Drying Time, Dehumidified Dryer h 6-8
Drying Temperature °C (°F) 100 (210)
Air Dew Point °C (°F) <-20 (<-4)
Processing Moisture Content % <0.10
Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.
ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.
Test temperatures are 23°C unless otherwise stated.

The above data are preliminary and are subject to change as additional data are developed on subsequent lots.

The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2007.
070830/070905
The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new
knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these
data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.
The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you
may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations
in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this
publication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent
counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical
application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont under
a written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information,
please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-2 and
DuPont CAUTION Regarding Medical Applications … H-50102-2.

plastics.dupont.com

5/5

You might also like