0% found this document useful (0 votes)
421 views97 pages

DSN N4 6284 B01 CO#00

This document provides design calculations for a logistics building. It includes 3 sections: 1) design information covering codes, assumptions, loads, and drawings, 2) computer design printouts and explanations, and 3) reference tables and data sheets. Section 1 describes the applicable codes, material specifications, design assumptions, load combinations, design summary, plan, elevations, frame sections, and wind bracing calculations.

Uploaded by

Tam Phan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
421 views97 pages

DSN N4 6284 B01 CO#00

This document provides design calculations for a logistics building. It includes 3 sections: 1) design information covering codes, assumptions, loads, and drawings, 2) computer design printouts and explanations, and 3) reference tables and data sheets. Section 1 describes the applicable codes, material specifications, design assumptions, load combinations, design summary, plan, elevations, frame sections, and wind bracing calculations.

Uploaded by

Tam Phan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 97

Page 1 of

DESIGN CALCULATIONS
Ver 99.11
ZS Job No. N2-6284 Building 01
Revision 00 Dated 24/12/19

LOGISTICS SOLUTION PROVIDER


Address:

Project Name NAKORN NAYOK


Building Name
Page 2 of
The Total No. Of Pages in this Document Are 106

Revision “00” of this Job Was

Designed By PLT
Checked By DVC
Date 24/12/19
Page 3 of

Job No.
N2-6284 Building No.
01 Revision No. 00

Introduction
This Design Calculations Package has been prepared using the latest applicable American codes and
standards and the latest developments in engineering practices. A competent design engineer prepared
the calculations and another competent engineer checked his work. The initials of both engineers are
shown on most pages.
The calculations have also been reviewed and certified by a registered professional engineer.
Computer programs, verified and tested by Zamil Steel, have been used where applicable to determine
structural requirements. The output of these programs has been incorporated in this package together
with explanation text where possible. The whole package has been prepared using an advanced
computer text processor.

For your easy reference, all pages have been numbered and a table of contents has been provided. We
have divided the package into three sections as follows:

1. Design Information: This section contains the description of the building designed, design
codes and material specifications used, design assumptions, loads and design sketches showing
building components layouts and members sizes.

2. Computer Design Printouts: This section includes the output of computer programs used in
the design along with explanations for the output where possible.

3. Design Reference Tables and Data Sheets: This section includes the mechanical properties of
all steel sections available for use by Zamil Steel and different load capacity tables. This section
for Zamil Steel standard designations and computer programs. also includes reference data

Please use this calculations package in conjunction with the drawings provided. You can resubmit this
package with the drawings to other parties for their approval as required, or, keep this package for
future reference. Zamil Steel does not require these calculations to be returned.

For any questions regarding this package please do not hesitate to contact our sales office. Zamil Steel
keeps records of reference on design calculations for each building designed as a part of Zamil Steel
total quality system.

Engineering Department
Zamil Steel
DESIGN SHEET Page 4 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

Table of Contents
Job No.
N2-6284 Building No.
01 Revision No.00

Introduction.........................................................................................................................................2

Table of Contents................................................................................................................................2

Section 1 : Design Information..........................................................................................................2


Applicable Design Codes........................................................................................................2
Material Specifications...........................................................................................................2
Design Assumptions................................................................................................................2
Load Combinations................................................................................................................2
Dead Load + Wind Load + Temperature Load Design Summary.....................................2
Plan...........................................................................................................................................2
End Wall Elevation.................................................................................................................2
Frame Cross Section @GL.(2-3)..........................................................................................2
Portal Detail.............................................................................................................................2
Frame Reactin.........................................................................................................................2

Section 2 : Computer Design Printouts............................................................................................2

Section 3 : Design Reference Tables and Computer Explanation......................................................2


DESIGN SHEET Page 5 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

Section 1 : Design Information

 Applicable Design Codes


 Material Specifications
 Design Assumptions and Load Combinations
 Design Summary
 Plan
 End Wall Elevation
 Frame Cross Section
 Canopy Details
 Roof Monitor Detail
 Drainage Design Sheet
 Wind Bracing Design Calculations
DESIGN SHEET Page 6 of
Job No. Building No. Rev. No. 00

Customer LogisticsApplicable
SolutionDesign
Provider
Codes
Date

Description Designed ByChecked By

Applicable Design Codes


The Pre-Engineered Building described in these calculations was designed according to the latest U.S.A.
Buildings and Design Codes that have been referred to in the design :

1. The loads as described in the Design Summary Sheet have been applied on the structure in
accordance with:

ASCE/SEI Minimum Design Load for Building and Other Structures , 2005 Edition, including
supplement No.1.
Live load applied on frame is 0.33kN/m2 in accordance with local code.
2. Hot rolled sections and built up components have been designed in accordance with :

AISC “American Institute of Steel Construction” Manual of Steel Construction - Allowable


Stress Design, 1989 Edition.
1 East Wacker Drive, Suite 3100, Chicago, Illinois 60601-2001.

3. Cold formed components have been designed in accordance with :

AISI “American Iron and Steel Institute” Cold Formed Steel Design Manual, 2001 Edition.
1000 16th Street, NW, Washington, DC 20036, USA

4. Welding has been applied in accordance with :

AWS D1.1/D1.1M : 2010: “American Welding Society” Structural Welding Code – Steel.
550 N.W. Lejeune Road, Miami, Florida 33126.
DESIGN SHEET Page 7 of
Job No. Building No. Rev. No. 00

Customer Logistics Material


Solution Provider Date
Specifications

Description Designed ByChecked By

Material Specifications
The following is the list of the material standards and specifications for which the building components have
been designed :

Material Specifications

Sl Minimum
Materials Specifications
No. Strength

1 Built-up ASTM A 572M Grade 345 Type 1 (or equivalent) Fy = 34.5 kN/cm2
Tubes JIS - G 3466 - STKR 490 (or equivalent) Fy = 32.5 kN/cm2

2 Hot Rolled Channels JIS G3101 - SS 400 (or equivalent) Fy = 24.5 kN/cm2
Beams &
JIS G3101 - SS 400 (or equivalent) Fy = 24.5 kN/cm2
Columns
Cold ASTM A 653M - 97 Grade SS 340 Class 1
3 Pre-Galvanized (or equivalent), Coating Z275 Fy = 34.0 kN/cm2
Formed
ASTM A 792M - 97 Grade SS345 Type B
4 Exterior Wall & Roof Panel (or equivalent), Coating AZM 150 Fy = 34.0 kN/cm2
ASTM A 792M - 97 Grade SS345 Type B,
5 MaxSEAM Roof Panel Coating AZM 150 or AS 1397-2001 Grade G300, Fy = 30.0 kN/cm2
Coating AZ 150 (or equivalent)
ASTM A 792M - 97 Grade SS345 Type B,
6 Mezzanine Deck Panel Coating AZM 150 or ASTM A653 SS50 Class 1, Fy = 34.0 kN/cm2
Coating G60 (or equivalent)
ASTM A 792M - 97 Grade SS345 Type B
7 Interior Liner Panel Fy = 34.0 kN/cm2
(or equivalent), Coating AZM 150
Rods JIS G3101 - SS 400 (or equivalent) Fu = 40.0 kN/cm2
8 X-Bracing
Angles/Sag Rods TCVN - 1765 - 75 CT38 (or higher grade) Fu = 37.2 kN/cm2
Fy = 23.5 kN/cm2
9 Anchor Bolts TCVN - 1765 - 75 CT38 (or higher grade) Fu = 37.2 kN/cm2
ASTM A325 M Class 8.8 Type 1 (or equivalent)
10 High Strength Bolts Fu = 83.0 kN/cm2
Hot Dip Galvanized
DIN 933 Class 4.6/4.8 (or equivalent)
11 Machine Bolts Fu = 40.0 kN/cm2
Electro Plated Yellow Chromate
Fy = Yield Strength, Fu = Tensile Strength
Zamil Steel reserves the rights to substitute, by equivalent or superior material, any of the above mentioned materials
subject to availability.
DESIGN SHEET Page 8 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Design Assumptions

 The main frame rafters and columns are rigidly connected to each other (using moment type
connections).
 The mainframe columns are pin connected to the concrete foundation.
 The lateral stability of the building is provided through the frame action of the main frames &
concrete foundation.
 The longitudinal stability of the building is provided through the truss action in the cross braced
bays of the building.
 The frame at endwalls are made of pin connected rafters and columns. The lateral stability of endwall
frames are provided by the diaphragm action of endwall sheeting & blockwall.
 EW girts is continous beam supported at the wind columns.
 The roof purlins and SW girts are continuous beams supported at rigid frame locations and span the
bay spacing of the building.
 The roof and wall sheeting provide lateral support for purlins.
 The stability of blockwall is not under scope of Zamil Steel.
 The building is designed as Fully Enclosed Building
Load Combinations
 Dead Load + Collateral Load + Live Load
 Dead Load + Collateral Load +Wind load
DESIGN SHEET Page 9 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

Design Summary
Frame Type Clear Span (CS) Panel Type Thick.(MM) Material
Building Width (MM) 12000 (C/C of column base) Roof N/A N/A N/A
Bay Spacing (MM) 3@8000 (C/C of column base ) Wall N/A N/A N/A
Liner N/A
Clear Height (MM) 4100 Cold Formed Sections Finish
Roof Slope 0.88: 10 B( Black), G/AZ(Either Galv. Or Aluzinc) Galvanized
Live Load (Roof) 0.57 KN/M2 Purlin Lap: 385 Max Spacings: Refer to cross section
Live Load (Frame) 0.33 KN/M2 @200Z17 for bays bct (1-2)&(3-4)
Collateral Load 0.05 KN/M2 @200Z15 for other bay
Wind Speed 110 KM/Hour
Dead Load (Self Wt) 0.10 KN/M2 SW Girt Lap: 385 Max Spacings: Refer to cross section
Seismic Loads 200Z15 for all bays

Crane Crane Rail Top Crane Wheel Max.Wheel


Cap. Make Center Of Type Base Load
Bea (With Impact)
m
(MT) (M) (M) (M) (KN)
Vert. Horiz. EW Girt Lap:By Pass Max Spacings: 1600 mm
200Z15 for all bays.
N/A
Eave Strut 180ES2.0
Crane Beam Design Refer to page(s) : N/A Bracing X-Bracing /Portals
Mezzanine Refer to page(s) : N/A Near Side Wall No. Of Bays 1 Type PT
Fascia Refer to page(s) : N/A Far Side Wall No. Of Bays 1 Type PT
Left End Wall Post & Beam Roof No. Of Bays 1 Type Rod
Type
Column Spacing : Refer to Plan Left End Wall No. Of Bays N/A Type Rod/PT
Right End Wall No. Of Bays N/A Type Rod
Right End Wall Post & Beam
Type
Column Spacing Refer to Plan

Rigid Frames On Grid Lines 2 -3 1 4

Remarks: A
S L O P E 0 .8 8 : 1 0 S L O P E 0 .8 8 : 1 0

1. The building is designed as Fully Enclosed Building.


2. Importance factor for Wind Load is 1.0
3. Detailing refer to PIS for more information.
4. Provide 1 row of 12mm dia sag rod for all purlin and girts C
P&B P& B

KEYPLAN
DESIGN SHEET Page 10 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

Plan

1 2 3 4

A P T- 1

R O O F B R A C IN G
P T-2

1 -R 2 4

P A R T I T IO N S P A R T I T IO N S

B #4 C O LU M N 2 00 C 2 5

#4 #4
#4
R ID G E L IN E S
C O LU M N 2 00 C 2 5

#4
#4

R O O F B R A C IN G

C
P T- 1 1 -R 2 4

P&B P&B

PLAN
NOTE
-# 4 : D E N O T E S D E T A IL - 0 4 W / S T R U T C L IP
-“ P T ” D E N O T E S P O R T A L F R A M E , R E F E R T O P O R T A L F R A M E D E T A I L S .
-P R O V ID E 2 0 0 Z 1 5 F O R A L L P A R T IT IO N G IR T S .
DESIGN SHEET Page 11 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

End Wall Elevation

E N D W A L L E L E V A T IO N @ G L (1 )
DESIGN SHEET Page 12 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

E N D W A L L E L E V A T IO N @ G L ( 4 )
DESIGN SHEET Page 13 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

Frame Cross Section @GL.(2-3)


DESIGN SHEET Page 14 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

Portal Detail
DESIGN SHEET Page 15 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


DESIGN SHEET Page 16 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

Frame Reactin

WIND CO LU MN RE AC T IO N
SI G N C ON V E N TI O N

+ ve

W L = ± 5 KN

DL + LL = - 6 KN

A 3 C
2 4

2 2

H1 1 H5 5

V1 V5

S TR U CTU R E RE AC TIO N S

Lo a d V 1 H1 V 5 H5 Fra m es a t
C a se s (k N ) (k N ) (k N ) (k N ) Grid L in e s
DE A D 11 3 11 -3 2- 3
CO L L 3 2 3 -2 2- 3
LIVE 17 7 17 -7 2- 3

W IN D E N D - 18 -3 - 18 3 2- 3
W I N D LE FT - 21 - 15 - 10 -6 2- 3
W IN D RIGH T - 10 6 - 21 15 2- 3
N O TE :
1. TH E G IV E N RE A C TIO N S A R E C AU S E D B Y U N - F AC T O R ED L O AD S .
2. D EA D D E N O TE S D EA D LO A D .
3. LIV E D EN O TE S L IV E L O A D .
4. C O LL DE N O T ES C O L LA TE R AL LO A D .
5. W I N D LE FT IS WI N D FR O M L EF T S I D E TO R IG H T SI D E.
6. W I N D R I G H T IS W IN D F RO M R IG H T S ID E TO L EL T S ID E .
7. W I N D EN D I S W IN D A LO N G TH E BU ILD I N G ( P E R PE N D IC U L A R T O TH E E N D W A LL ) .
DESIGN SHEET Page 17 of
Job No. Building No. Rev. No. 00

Eave Drainage Design


Customer Logistics Solution Provider Date
Width of Drained Area (Left) 6.00 Meter
Description Designed ByChecked
Width of Drained Area (Right) By
0.00 Meter
Drainage
Total WidthDesign Sheet
of Drained Area ' W ' @GL.A
6.00 & D (Eave Gutter)
Meter

Roof Slope 0.88 :10 Roof Slope Constant ' C '


Slope C
Rain Fall Intensity ' I ' 150.00 mm per Hour 0.0> <2.5 1.00
2.5> <6.5 1.10
Gutter Type Eave Gutter 6.5> <10.0 1.20
Gutter Average Width ' B ' 0.17 Meter >10.0 1.30
Gutter Depth / Width ' M ' 0.92

Downspout Area ' A ' 88.00 cm 2

Required Down Spout Spacing ' DS '

The following Calculations are based on Formulas derived by:


"The Copper Development Association Inc."

Based on Gutter Capacity


DS= 19 (B)28/13 (M)16/13 (334500 / CWI)10/13
DS= 34.73 Meter

Based on Down Spout Capacity


DS= 440 A / CWI
DS= 43.02 Meter

Maximum Down Spout Spacing 34.73 Meter


Use single STD. Down Spouts @ ALTERNATEColumn Spacing
DESIGN SHEET Page 18 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Wind Bracing Design Calculations
Capacity (kN)
Size,  W/Wind
Bay-Spacing = 8.000 m R24 mm Grade CT3 74
Eave-Height = ±4.850m R16 mm Grade CT3 33
Wind-Velocity =110 km/h
GCp = 1.0
Roof Rod-Length = (Bay  Spacing2  Column  Spacing2 ) = m
Wall Rod-Length =  Bay  Spacing 2  Eave  Height 2  = m
Rod  Force  Rod  Length   P / Bay = kN
2
WL = 0.480 KN/m follow ASCE7-05’s limitation
WL = 0.480 kN/m2 Bay = 8.000 m No. of Braced Bays
Eave Strut (N) = 1Plate
W/Shear
Shear Capacity =22kN Shear Capacity =69 kN Shear Capacity =45kN Shear Capacity
Shear=45 kN Shear Capacity =90
Capacity=97kN
Detail # kN
8

Standard Connection Strut Purlin With Strut Clip With Strut Clip Clip Connection With Strut Purlin using
Clip Connection
Detail # 1 Detail # 3 Detail # 4 Detail # 5 Eave StrutDetail # 6
Standard
Shear Capacity= 47kN
(1) (2) (3) (4) (5) (6) (7) (8) Detail
(9)# 7 (10)

No.
Average
Spacing
Height Area
(m2)
P (kN)
 P Rod
Length
Rod
Force
Size
Of
Purlin
Conn.
(m) (m) (kN) (m) (kN) Bracing
P1 3 5.262 15.757 3.78 3.78 10 4.725 1R-24 Det#04

P2 3 4.582 13.746 3.3 7.08 10 8.85 1R-24 Det#04


DESIGN SHEET Page 19 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

Section 2 : Computer Design Printouts

*0 ASFAD design for Rigid Frames


(Advanced Steel Frame Analysis & Design)
*1 Job Identification and Run Parameters
*2 Macro Input Echo
*3 Detail Input Report
Frame Geometry & Properties
Flange Brace Details
Load Cases
Load Categories & Conditions
*4 Frame Reactions & Deflection Report
*5 Design Summary Report
(Frame Stress Analysis & Design)
DESIGN SHEET Page 20 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

RF-2-3
*HEADER
VERSION: 1911169
TITLE: N2-6284 REV 0
INIT: PLT
CONST: Page=66 Fy=34.50 Fp=0.75 Fc=2.50U Segment=0.60 Bolt=A325-36SH Moment=0.50 Fbrac=0
CONST: Code=AISC89 MinABolt=1-4
OUTPUT: I R D C -FC -FM -FP T -M U E4

*SPANS
12.500
EH 4.582

*MEMBERS

// 1 - 2
250.00 Slope=0.000 Ht=0 Girt=200.0 Disp=0.00 Fy=34.50 Fix=NT Conn=2
350.00 125.00x05.00 4.00 125.00x05.00 0.000
Bracing 2.65D 3.65T

// 2 - 3
300.00 Slope=0.800 Purlin=200.0 End=6.250 Rel=N Conn=2
200.00 125.00x05.00 4.00 125.00x05.00 0.000
Bracing 0.70T 2.20D 3.70D 4.49T 6.00D
Sym

*LOADS
DEAD 0.10
WALL 0.10 -1.00 -1.00
LIVE 0.33
COLL 0.05
SNOW 0.00 P1-100.0
TEMP 0.00 0.00
BAY 8.00
WIND D=B 110.00 CA705 SFICN

STATIC 4 DEAD

*LOADCOND

*AUTODESIGN
Vert-Def 180.00
Sway-Def 45.00

#StdAll BC
#DwRatio 4.000
#MinThk 0 0
#Max_Kw 180.000
#Max_Kb 34.000
#Max_Uc 0.850
#Max_LR 0

*CONN
DESIGN SHEET Page 21 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

*END

RF-OUTPUT
** Front Page [MAC-ON] .....

ZAMIL STEEL INDUSTRIES


P.O.Box 877
Dammam 31421
Kingdom of Saudi Arabia

A S F A D
Advanced Steel Frame Analysis & Design
Version No. 1911.169 Nov 2019
Founded(1995) by: K.R.Ezzat
Developed by: Engineering Systems Dept.

File Name : C:\Users\sv4012\Desktop\N2-6284\ASFAD\RF 2-3.out


Run By : PLT
Date : 24-12-2019 at 16:57
Design Code : [AISC-89]

Units : Metric
Modulus of Elasticity : 19995.00 kN/cm2
Coefficient of Expansion : 0.0000117

Concrete Bearing Stress : 0.75 kN/cm2


DESIGN SHEET Page 22 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Steel Density : 7850.00 Kg/m3
Segment Size : 0.60 m

Page Size : 66

...........................................................................................

Macro Input Report


Page Number.. 1
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

*HEADER
VERSION: 1911169
TITLE: N2-6284 REV 0
INIT: PLT
CONST: PAGE=66 FY=34.50 FP=0.75 FC=2.50U SEGMENT=0.60 BOLT=A325-36SH MOMENT=0.50 FBRAC=0
CONST: CODE=AISC89 MINABOLT=1-4
OUTPUT: I R D C -FC -FM -FP T -M U E4

*SPANS
12.500
EH 4.582

*MEMBERS
// 1 - 2
250.00 SLOPE=0.000 HT=0 GIRT=200.0 DISP=0.00 FY=34.50 FIX=NT CONN=2
350.00 125.00X05.00 4.00 125.00X05.00 0.000
BRACING 2.65D 3.65T
// 2 - 3
300.00 SLOPE=0.800 PURLIN=200.0 END=6.250 REL=N CONN=2
200.00 125.00X05.00 4.00 125.00X05.00 0.000
BRACING 0.70T 2.20D 3.70D 4.49T 6.00D
SYM

*LOADS
DEAD 0.10
WALL 0.10 -1.00 -1.00
LIVE 0.33
COLL 0.05
SNOW 0.00 P1-100.0
TEMP 0.00 0.00
BAY 8.00
WIND D=B 110.00 CA705 SFICN
STATIC 4 DEAD

*LOADCOND

*AUTODESIGN
VERT-DEF 180.00
SWAY-DEF 45.00
#STDALL BC
#DWRATIO 4.000
#MINTHK 0 0
#MAX_KW 180.000
#MAX_KB 34.000
#MAX_UC 0.850
#MAX_LR 0
DESIGN SHEET Page 23 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

*CONN

*END
.
.** Errors Log **
.
.
.** Processed with No Errors **

...........................................................................................

Input Details Report


Page Number.. 1
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

Coordinates Restraints Elastic Restraint Coeff.


Node X Y X Y M X Y M
No. (.....meters....) (Y=Rest. E=Elas.) kN/m kN/m kN.m/deg
---- ----------------- ----------------- ------------------------------

1 0.330 0.000 Y Y
2 0.380 4.256
3 6.250 4.776
4 12.120 4.256
5 12.170 0.000 Y Y

Offsets Releases
Member No of Start End Start End
No. Start End Sections (.....m.....) X Y M X Y M
------------- -------- ------------- ------------

1 1 - 2 1 0.00 0.14
2 2 - 3 1 0.17 0.00
3 3 - 4 1 0.00 0.17
4 5 - 4 1 0.00 0.14

Web Depth Top Flange Web Bottom Flange


Section Length (....mm....) Section (.....mm.....) thick (.....mm.....)
Member No. (m) Start End type width x thick (mm) width x thick
--------- ---- ------- --------------- ------- ---------------- ------ ----------------

1 - 2 1 4.256 250.00 350.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00

2 - 3 1 5.893 300.00 200.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00

3 - 4 1 5.893 200.00 300.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00

5 - 4 1 4.256 250.00 350.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00

Member Bracings (distance ..meters , T:Top Flg - B:Bottom Flg - D:Double both Flgs)
--------- ------------------------------------------------------------------------------
DESIGN SHEET Page 24 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


1 - 2 2.13N 2.65D 3.65T 4.26N

2 - 3 0.00N 0.35T 1.85D 2.95N 3.35D 4.14T 5.65D

3 - 4 0.25D 1.76T 2.55D 2.95N 4.05D 5.55T 5.89N

5 - 4 2.13N 2.65D 3.65B 4.26N

...........................................................................................

Input Details Report


Page Number.. 2
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

Load Load Value Start/End Start & End Distances Angle


No. Member Type ( kN kN/m kN.m ) (..m.. '-' ratio of length) (Deg)
--- --------- ---- ---------------------- -----------------------------------

Load Case No. 1 DEAD

1 2 - 3 GWY -1.00 x Own WT from 0.00 to -1.00


2 1 - 2 GWY -1.00 x Own WT from 0.00 to -1.00
3 3 - 4 GWY -1.00 x Own WT from 0.00 to -1.00
4 5 - 4 GWY -1.00 x Own WT from 0.00 to -1.00
5 2 - 3 GUY -0.80 from 0.00 to -1.00
6 3 - 4 GUY -0.80 from 0.00 to -1.00
7 2 - 3 GCY -0.30 at 0.00
8 1 - 2 GUY -0.80 from 0.00 to -1.00
9 4 - 3 GCY -0.30 at 0.00
10 5 - 4 GUY -0.80 from 0.00 to -1.00

Load Case No. 2 COLL

1 2 - 3 GUY -0.40 from 0.00 to -1.00


2 3 - 4 GUY -0.40 from 0.00 to -1.00
3 2 - 3 GCY -0.15 at 0.00
4 4 - 3 GCY -0.15 at 0.00

Load Case No. 3 LIVE

1 2 - 3 GUY -2.63 from 0.00 to -1.00


2 3 - 4 GUY -2.63 from 0.00 to -1.00
3 2 - 3 GCY -1.00 at 0.00
4 4 - 3 GCY -1.00 at 0.00

Load Case No. 4 WINDEND

1 1 - 2 GUX -2.08 from 0.00 to -1.00


2 2 - 1 GCX -0.68 at 0.00
3 2 - 3 LCY 1.10 at 0.00
4 5 - 4 GUX 2.08 from 0.00 to -1.00
5 4 - 5 GCX 0.68 at 0.00
6 4 - 3 LCY -1.10 at 0.00
7 2 - 3 LUY 2.88 from 0.00 to -1.00
8 3 - 4 LUY 2.88 from 0.00 to -1.00
DESIGN SHEET Page 25 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Load Case No. 5 WINDLEFT

1 1 - 2 GUX 1.40 from 0.00 to -1.00


2 2 - 1 GCX 0.46 at 0.00
3 2 - 3 LCY 1.10 at 0.00
4 5 - 4 GUX 2.99 from 0.00 to -1.00
5 4 - 5 GCX 0.97 at 0.00
6 4 - 3 LCY -0.69 at 0.00
7 2 - 3 LUY 2.88 from 0.00 to -1.00
8 3 - 4 LUY 1.82 from 0.00 to -1.00

Load Case No. 6 WINDRIGHT

1 1 - 2 GUX -2.99 from 0.00 to -1.00


2 2 - 1 GCX -0.97 at 0.00

...........................................................................................

Input Details Report


Page Number.. 3
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

Load Load Value Start/End Start & End Distances Angle


No. Member Type ( kN kN/m kN.m ) (..m.. '-' ratio of length) (Deg)
--- --------- ---- ---------------------- -----------------------------------

Load Case No. 6 WINDRIGHT

3 2 - 3 LCY 0.69 at 0.00


4 5 - 4 GUX -1.40 from 0.00 to -1.00
5 4 - 5 GCX -0.46 at 0.00
6 4 - 3 LCY -1.10 at 0.00
7 2 - 3 LUY 1.82 from 0.00 to -1.00
8 3 - 4 LUY 2.88 from 0.00 to -1.00

Static Load Cases :

1. Load Case No. 1 DEAD

Load Category No. 1 [Indiv.] COLL

1. Load Case No. 2 COLL

Load Category No. 2 [Indiv.] LIVE

1. Load Case No. 3 LIVE

Load Category No. 3 [Indiv.] WIND

1. Load Case No. 4 WINDEND


2. Load Case No. 5 WINDLEFT
3. Load Case No. 6 WINDRIGHT
DESIGN SHEET Page 26 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

Load Condition No. 1 @ RSD With 1.00 Stress Factor


1. 1.00 x DEAD
2. 1.00 x COLL
3. 1.00 x LIVE

Load Condition No. 2 @ RSD With 1.00 Stress Factor


1. 1.00 x DEAD
2. 1.00 x COLL
3. 0.75 x LIVE
4. 0.75 x WIND

Load Condition No. 3 @ RSD With 1.00 Stress Factor


1. 1.00 x DEAD
2. 1.00 x COLL
3. 1.00 x WIND

Load Condition No. 4 @ RSD With 1.00 Stress Factor


1. 0.60 x DEAD

...........................................................................................

Input Details Report


Page Number.. 4
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

Load Condition No. 4 @ RSD With 1.00 Stress Factor


2. 1.00 x WIND

...........................................................................................

Reactions & Displacements Report


Page Number.. 5
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

Structure Reactions and Displacements - Load Case no. 1...DEAD

Vertical Horizontal Moment Vertical Horizontal Rotation


Node Reaction Reaction Reaction Displac. Displac. Angle
No. (kN) (kN) (kN.m) (cm) (cm) (deg)
---- ---------- ---------- ---------- ---------- ---------- ----------
1 10.248 2.564 0.000 0.000 0.000 0.071
2 -0.000 0.000 -0.000 -0.006 -0.110 -0.079
3 -0.000 0.000 0.000 -1.294 -0.000 0.000
4 0.000 0.000 -0.000 -0.006 0.110 0.079
5 10.248 -2.564 0.000 0.000 0.000 -0.071

Structure Reactions and Displacements - Load Case no. 2...COLL

Vertical Horizontal Moment Vertical Horizontal Rotation


DESIGN SHEET Page 27 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Node Reaction Reaction Reaction Displac. Displac. Angle
No. (kN) (kN) (kN.m) (cm) (cm) (deg)
---- ---------- ---------- ---------- ---------- ---------- ----------
1 2.507 1.044 -0.000 0.000 0.000 0.029
2 -0.000 -0.000 -0.000 -0.002 -0.045 -0.032
3 0.000 -0.000 -0.000 -0.532 -0.000 0.000
4 -0.000 0.000 -0.000 -0.002 0.045 0.032
5 2.507 -1.044 0.000 0.000 0.000 -0.029

Structure Reactions and Displacements - Load Case no. 3...LIVE

Vertical Horizontal Moment Vertical Horizontal Rotation


Node Reaction Reaction Reaction Displac. Displac. Angle
No. (kN) (kN) (kN.m) (cm) (cm) (deg)
---- ---------- ---------- ---------- ---------- ---------- ----------
1 16.499 6.863 0.000 0.000 0.000 0.193
2 -0.000 -0.000 -0.000 -0.011 -0.299 -0.213
3 -0.000 -0.000 -0.000 -3.495 -0.000 0.000
4 0.000 -0.000 -0.000 -0.011 0.299 0.213
5 16.499 -6.863 0.000 0.000 0.000 -0.193

Structure Reactions and Displacements - Load Case no. 4...WINDEND

Vertical Horizontal Moment Vertical Horizontal Rotation


Node Reaction Reaction Reaction Displac. Displac. Angle
No. (kN) (kN) (kN.m) (cm) (cm) (deg)
---- ---------- ---------- ---------- ---------- ---------- ----------
1 -18.001 -2.840 -0.000 0.000 0.000 -0.145
2 -0.000 -0.000 0.000 0.012 0.278 0.184
3 0.000 0.000 0.000 3.356 0.000 -0.000
4 -0.000 0.000 0.000 0.012 -0.278 -0.184
5 -18.001 2.840 -0.000 0.000 0.000 0.145

...........................................................................................

Reactions & Displacements Report


Page Number.. 6
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

Structure Reactions and Displacements - Load Case no. 5...WINDLEFT

Vertical Horizontal Moment Vertical Horizontal Rotation


Node Reaction Reaction Reaction Displac. Displac. Angle
No. (kN) (kN) (kN.m) (cm) (cm) (deg)
---- ---------- ---------- ---------- ---------- ---------- ----------
1 -20.080 -14.080 -0.000 0.000 0.000 -0.893
2 0.000 0.000 0.000 -0.035 4.510 -0.163
3 -0.000 -0.000 -0.000 2.924 4.260 0.188
4 -0.000 -0.000 0.000 0.055 4.018 -0.504
5 -9.292 -5.447 -0.000 0.000 0.000 -0.601

Structure Reactions and Displacements - Load Case no. 6...WINDRIGHT

Vertical Horizontal Moment Vertical Horizontal Rotation


Node Reaction Reaction Reaction Displac. Displac. Angle
No. (kN) (kN) (kN.m) (cm) (cm) (deg)
DESIGN SHEET Page 28 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


---- ---------- ---------- ---------- ---------- ---------- ----------
1 -9.292 5.447 -0.000 0.000 0.000 0.601
2 -0.000 -0.000 -0.000 0.055 -4.018 0.504
3 0.000 0.000 -0.000 2.923 -4.260 -0.188
4 -0.000 -0.000 0.000 -0.035 -4.510 0.163
5 -20.080 14.080 -0.000 0.000 0.000 0.893

...........................................................................................

Reactions & Displacements Report


Page Number.. 7
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

Structure Max Positive Reactions Structure Max Negative Reactions

Vertical Horizontal Moment Vertical Horizontal Moment


Node Reac. Load Reaction Reaction Reaction Load Reaction Reaction Reaction
No. Type Cond (kN) (kN) (kN.m) Cond (kN) (kN) (kN.m)
---- ---- ---- ---------- ---------- ---------- ---- ---------- ---------- ----------

1 H 2 18.160 12.841 -0.000 4 -13.931 -12.542 -0.000


1 V 1 29.253 10.471 0.000 4 -13.931 -12.542 -0.000

5 H 4 -13.931 12.542 0.000 2 18.160 -12.841 0.000


5 V 1 29.253 -10.471 0.000 4 -13.931 12.542 0.000

...........................................................................................

Design Summary Report based on AISC-89


Page Number.. 8
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

****************************************************************************************
Member 1 - 2 Length = 4.256 meters Fy = 34.50 kN/cm2 Weight = 82.079 Kg
****************************************************************************************

Web Depth Top Flange Web Bottom Flange


Section Length (....mm....) Section (.....mm.....) thick (.....mm.....) Unity
No. (m) Start End type width x thick (mm) width x thick Check
---- ------- --------------- ------- ---------------- ------ ---------------- -----
1 4.256 250.00 350.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00 Pass

Maximum Forces Allowable Stresses Calculated Stresses


Section Moment Axial @ Dist Load (......kN/cm2.....) (......kN/cm2.....) Stress
No. (kN.m) (kN) (m) cond Fa Fb-Top Fb-Bott fa fb-Top fb-Bott Ratio
---- ---------------------------- --------------------- --------------------- -------
1 -41.78 -25.30 4.12 1 11.39 20.70 18.90 -0.95 14.01 -14.01 0.82

Section Maximum Allow. Calcu. Max + Deflection Max - Deflection


No. Shear @ Dist Load Fv fv Stress Def. @ Dist Load Def. @ Dist Load
(kN) (m) cond (...kN/cm2..) Ratio (cm) (m) cond (cm) (m) cond
---- -------------------- ------ ------ ------ ------------------ ------------------
1 12.63 0.00 2 11.84 1.26 0.11 4.08 4.12 3 -4.39 4.12 4
DESIGN SHEET Page 29 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


****************************************************************************************
Member 2 - 3 Length = 5.893 meters Fy = 34.50 kN/cm2 Weight = 104.352 Kg
****************************************************************************************

Web Depth Top Flange Web Bottom Flange


Section Length (....mm....) Section (.....mm.....) thick (.....mm.....) Unity
No. (m) Start End type width x thick (mm) width x thick Check
---- ------- --------------- ------- ---------------- ------ ---------------- -----
1 5.893 300.00 200.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00 Pass

Maximum Forces Allowable Stresses Calculated Stresses


Section Moment Axial @ Dist Load (......kN/cm2.....) (......kN/cm2.....) Stress
No. (kN.m) (kN) (m) cond Fa Fb-Top Fb-Bott fa fb-Top fb-Bott Ratio
---- ---------------------------- --------------------- --------------------- -------
1 -39.43 -12.45 0.17 1 11.82 20.70 19.18 -0.51 16.05 -16.05 0.88

Section Maximum Allow. Calcu. Max + Deflection Max - Deflection


No. Shear @ Dist Load Fv fv Stress Def. @ Dist Load Def. @ Dist Load
(kN) (m) cond (...kN/cm2..) Ratio (cm) (m) cond (cm) (m) cond
---- -------------------- ------ ------ ------ ------------------ ------------------
1 21.90 0.17 1 9.87 1.82 0.18 2.72 4.64 4 -5.30 5.89 1
----------------------------------------------------------------------------------------

...........................................................................................

Design Summary Report based on AISC-89


Page Number.. 9
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

****************************************************************************************
Member 3 - 4 Length = 5.893 meters Fy = 34.50 kN/cm2 Weight = 104.352 Kg
****************************************************************************************

Web Depth Top Flange Web Bottom Flange


Section Length (....mm....) Section (.....mm.....) thick (.....mm.....) Unity
No. (m) Start End type width x thick (mm) width x thick Check
---- ------- --------------- ------- ---------------- ------ ---------------- -----
1 5.893 200.00 300.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00 Pass

Maximum Forces Allowable Stresses Calculated Stresses


Section Moment Axial @ Dist Load (......kN/cm2.....) (......kN/cm2.....) Stress
No. (kN.m) (kN) (m) cond Fa Fb-Top Fb-Bott fa fb-Top fb-Bott Ratio
---- ---------------------------- --------------------- --------------------- -------
1 -39.43 -12.45 5.72 1 11.82 20.70 19.18 -0.51 16.05 -16.05 0.88

Section Maximum Allow. Calcu. Max + Deflection Max - Deflection


No. Shear @ Dist Load Fv fv Stress Def. @ Dist Load Def. @ Dist Load
(kN) (m) cond (...kN/cm2..) Ratio (cm) (m) cond (cm) (m) cond
---- -------------------- ------ ------ ------ ------------------ ------------------
1 21.90 5.72 1 9.87 1.82 0.18 2.72 1.25 4 -5.30 0.00 1

****************************************************************************************
Member 5 - 4 Length = 4.256 meters Fy = 34.50 kN/cm2 Weight = 82.079 Kg
****************************************************************************************

Web Depth Top Flange Web Bottom Flange


DESIGN SHEET Page 30 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Section Length (....mm....) Section (.....mm.....) thick (.....mm.....) Unity
No. (m) Start End type width x thick (mm) width x thick Check
---- ------- --------------- ------- ---------------- ------ ---------------- -----
1 4.256 250.00 350.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00 Pass

Maximum Forces Allowable Stresses Calculated Stresses


Section Moment Axial @ Dist Load (......kN/cm2.....) (......kN/cm2.....) Stress
No. (kN.m) (kN) (m) cond Fa Fb-Top Fb-Bott fa fb-Top fb-Bott Ratio
---- ---------------------------- --------------------- --------------------- -------
1 41.78 -25.30 4.12 1 11.39 18.90 20.70 -0.95 -14.01 14.01 0.82

Section Maximum Allow. Calcu. Max + Deflection Max - Deflection


No. Shear @ Dist Load Fv fv Stress Def. @ Dist Load Def. @ Dist Load
(kN) (m) cond (...kN/cm2..) Ratio (cm) (m) cond (cm) (m) cond
---- -------------------- ------ ------ ------ ------------------ ------------------
1 12.63 0.00 2 11.84 1.26 0.11 4.39 4.12 4 -4.08 4.12 3
----------------------------------------------------------------------------------------
Frame Weight = 372.9 Kg Surface Area = 23.0 m2 ( 48.4 m2/Ton)
Conn. Weight = 92.7 Kg

...........................................................................................

Unity Check AISC-89 & Deflection Summary Report


Page Number.. 10
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

Section Length Shear AX+BM Max + Def Max - Def Check


No. (m) Cond Uc Cond Uc Cond (cm) Cond (cm)
-----------------------------------------------------------------------------------
Member 1 - 2 1 4.256 | 2 0.11 1 0.82 | 3 4.08 4 -4.39 | Pass
-----------------------------------------------------------------------------------
Member 2 - 3 1 5.893 | 1 0.18 1 0.88 | 4 2.72 1 -5.30 | Pass > User max UC
-----------------------------------------------------------------------------------
Member 3 - 4 1 5.893 | 1 0.18 1 0.88 | 4 2.72 1 -5.30 | Pass > User max UC
-----------------------------------------------------------------------------------
Member 5 - 4 1 4.256 | 2 0.11 1 0.82 | 4 4.39 3 -4.08 | Pass
-----------------------------------------------------------------------------------

...........................................................................................

Connections Summary Report based on AISC-89


Page Number.. 11
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

********************************************************************************
Connection Type : Knee Joints [ 1 2 3 ] Member 1 - 2
********************************************************************************

Section dimensions :
Web Top/Outer Flange Bot/inner Flange
(.....mm......) (.....mm......) (.....mm......)
--------------- ---------------- ----------------
sec @ conn member 350.00 x 4.00 125.00 x 5.00 125.00 x 5.00
sec @ other member 300.00 x 4.00 125.00 x 5.00 125.00 x 5.00
DESIGN SHEET Page 31 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Controlling Forces :
Moment Axial Load Shear 50% Section
kN.m kN Cond kN Capac. kN.m
-------- -------- ---- ------- -------------
-41.78 -25.30 1 10.17 25.42
39.03 16.45 4 10.17 25.42

Connection Design :

Bolts conforming to ASTM A-325

Top/Outer Bolts 2 Rows (1 Outside) x 2 = 4 size 20.00 mm


Bot/Inner Bolts 1 Rows (0 Outside) x 2 = 2 size 20.00 mm

Total Bolts 3 Rows (1 Outside) x 2 = 6 size 20.00 mm

End plate size 200 x 490 x 18 mm Fy = 34.50 kN/cm2

No. of Top/Outer Stiffeners = 0


No. of Bot/Inner Stiffeners = 0

Knee Web of 4.00 mm is O.K.

Actual Allowable
kN kN Ratio
--------- --------- -----
Top/Outer Bolt Tension 25.72 95.28 0.27
Bot/Inner Bolt Tension 67.12 95.28 0.70

Top/Outer Plate Moment 2.76 13.97 0.20


Bot/Inner Plate Moment 11.54 13.97 0.83

Average Bolt Shear 1.70 45.46 0.04

Knee Web Plate Shear 10.00 12.28 0.81

Standard Connection Code ## K04220 -18 ##

--------------------------------------------------------------------------------

...........................................................................................

Connections Summary Report based on AISC-89


Page Number.. 12
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

********************************************************************************
Connection Type : Ridge Joints [ 2 3 4 ] Member 2 - 3
********************************************************************************

Section dimensions :
Web Top/Outer Flange Bot/inner Flange
(.....mm......) (.....mm......) (.....mm......)
--------------- ---------------- ----------------
sec @ connection 200.78 x 4.00 125.00 x 5.00 125.00 x 5.00
sec @ conn member 200.00 x 4.00 125.00 x 5.00 125.00 x 5.00
DESIGN SHEET Page 32 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


sec @ other member 200.00 x 4.00 125.00 x 5.00 125.00 x 5.00

Controlling Forces :
Moment Axial Load Shear 50% Section
kN.m kN Cond kN Capac. kN.m
-------- -------- ---- ------- -------------
-9.72 12.43 4 2.08 15.58
20.59 -10.47 1 2.08 15.58

Connection Design :

Bolts conforming to ASTM A-325

Top/Outer Bolts 2 Rows (1 Outside) x 2 = 4 size 16.00 mm


Bot/Inner Bolts 2 Rows (1 Outside) x 2 = 4 size 16.00 mm

Total Bolts 4 Rows (2 Outside) x 2 = 8 size 16.00 mm

End plate size 200 x 435 x 12 mm Fy = 34.50 kN/cm2

No. of Top/Outer Stiffeners = 0


No. of Bot/Inner Stiffeners = 0

Actual Allowable
kN kN Ratio
--------- --------- -----
Top/Outer Bolt Tension 18.26 60.98 0.30
Bot/Inner Bolt Tension 22.88 60.98 0.38

Top/Outer Plate Moment 2.01 6.21 0.32


Bot/Inner Plate Moment 2.52 6.21 0.41

Average Bolt Shear 0.26 29.09 0.01

Standard Connection Code ## RS4416 -12 ##

--------------------------------------------------------------------------------

...........................................................................................

Connections Summary Report based on AISC-89


Page Number.. 13
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

********************************************************************************
Connection Type : Knee Joints [ 5 4 3 ] Member 5 - 4
********************************************************************************

Section dimensions :
Web Top/Outer Flange Bot/inner Flange
(.....mm......) (.....mm......) (.....mm......)
--------------- ---------------- ----------------
sec @ conn member 350.00 x 4.00 125.00 x 5.00 125.00 x 5.00
sec @ other member 300.00 x 4.00 125.00 x 5.00 125.00 x 5.00

Controlling Forces :
DESIGN SHEET Page 33 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Moment Axial Load Shear 50% Section
kN.m kN Cond kN Capac. kN.m
-------- -------- ---- ------- -------------
41.78 -25.30 1 10.17 25.42
-39.03 16.45 4 10.17 25.42

Connection Design :

Bolts conforming to ASTM A-325

Top/Outer Bolts 2 Rows (1 Outside) x 2 = 4 size 20.00 mm


Bot/Inner Bolts 1 Rows (0 Outside) x 2 = 2 size 20.00 mm

Total Bolts 3 Rows (1 Outside) x 2 = 6 size 20.00 mm

End plate size 200 x 490 x 18 mm Fy = 34.50 kN/cm2

No. of Top/Outer Stiffeners = 0


No. of Bot/Inner Stiffeners = 0

Knee Web of 4.00 mm is O.K.

Actual Allowable
kN kN Ratio
--------- --------- -----
Top/Outer Bolt Tension 25.72 95.28 0.27
Bot/Inner Bolt Tension 67.12 95.28 0.70

Top/Outer Plate Moment 2.76 13.97 0.20


Bot/Inner Plate Moment 11.54 13.97 0.83

Average Bolt Shear 1.70 45.46 0.04

Knee Web Plate Shear 10.00 12.28 0.81

Standard Connection Code ## K04220 -18 ##

--------------------------------------------------------------------------------

...........................................................................................

Connections Summary Report based on AISC-89


Page Number.. 14
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

********************************************************************************
Connection Type : Pinned Base at Joint 1 Member 1 - 2
********************************************************************************

Section dimensions :
Web Top/Outer Flange Bot/inner Flange
(.....mm......) (.....mm......) (.....mm......)
--------------- ---------------- ----------------
sec @ Connection 250.00 x 4.00 125.00 x 5.00 125.00 x 5.00

Controlling Forces :
DESIGN SHEET Page 34 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Moment Vert. Load Horiz.
kN.m kN Cond kN
-------- -------- ---- -------
0.00 13.93 4 12.84
-0.00 -29.25 1 12.84

Connection Design :

Bolts conforming to ASTM F-1554 Gr 36 - SH25UD

Anchor bolts 2 Rows (all inside) x 2 = 4 size 20.00 mm

Base plate size 225 x 295 x 12 mm Fy = 34.50 kN/cm2

Actual Allowable
kN kN Ratio
--------- --------- -----
Anchor Bolt Tension 3.48 41.47 0.08
Bearing stress /cm2 0.04 0.89 0.05
Base Plate Moment 0.75 6.21 0.12
Average Bolt Shear 3.21 21.36 0.15

Standard Connection Code ## BR420-12 ##

--------------------------------------------------------------------------------

...........................................................................................

Connections Summary Report based on AISC-89


Page Number.. 15
N2-6284 REV 0 16:57 24-12-2019
----------------------------------------------------------------------------------------

********************************************************************************
Connection Type : Pinned Base at Joint 5 Member 5 - 4
********************************************************************************

Section dimensions :
Web Top/Outer Flange Bot/inner Flange
(.....mm......) (.....mm......) (.....mm......)
--------------- ---------------- ----------------
sec @ Connection 250.00 x 4.00 125.00 x 5.00 125.00 x 5.00

Controlling Forces :
Moment Vert. Load Horiz.
kN.m kN Cond kN
-------- -------- ---- -------
-0.00 13.93 4 12.84
-0.00 -29.25 1 12.84

Connection Design :

Bolts conforming to ASTM F-1554 Gr 36 - SH25UD

Anchor bolts 2 Rows (all inside) x 2 = 4 size 20.00 mm

Base plate size 225 x 295 x 12 mm Fy = 34.50 kN/cm2


DESIGN SHEET Page 35 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

Actual Allowable
kN kN Ratio
--------- --------- -----
Anchor Bolt Tension 3.48 41.47 0.08
Bearing stress /cm2 0.04 0.89 0.05
Base Plate Moment 0.75 6.21 0.12
Average Bolt Shear 3.21 21.36 0.15

Standard Connection Code ## BR420-12 ##

--------------------------------------------------------------------------------
DESIGN SHEET Page 36 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

ROOF-PURLIN

*HEADER
Title: N4-5831-B01-A01-CO#00 *** ROOF PURLIN (ZONE 1,2) ***
Init: PLT
CONST: Page=66 Code=AISI01 Segment=0.10
OUTPUT: -I -D

*Options
POSDEF: 120
NEGDEF: 150
STDSEC: 202
STDLAP: 104
BWIDTH: 125
MINSEC: 0
CURSEC: 0
ESTRUT: 0
FLUSHB: 1
SUPPOB: 1
BFLBRC: 0
FUNBRC: 0
USRLAP: 0
MAX-UC: 0.90

*SPANS
1 8.000 Z-200X17 Flush Lap385 0 0 -1.0
2 8.000 Z-200X17 Lap385 Lap385 0 0 -1.0
3 8.000 Z-200X17 Lap385 Flush 0 0 -1.0

*LOADS
//ASCE7-05
//DL = 0.1 ; LL= 0.57 ; COLL =0.05 ; q = 0.48 ; TRI = 1.5m
////GCp +GCpi GCp -GCpi
/Zone 1-3(+) 0.48
/Zone 1(-) -0.98
/Zone 2(-) -1.38
/Zone 3(-) -2.18

1 COLL GUY 0.0 -0.08 -1.00


2 COLL GUY 0.0 -0.08 -1.00
3 COLL GUY 0.0 -0.08 -1.00

1 DEAD GUY -0.15 0.00 -1.00


1 LIVE GUY -0.86 0.00 -1.00
1 WIND1 GUY -0.35 0.00 -1.00
1 WIND2 GUY 0.71 0.00 -1.00

2 DEAD GUY -0.15 0.00 -1.00


2 LIVE GUY -0.86 0.00 -1.00
2 WIND1 GUY -0.35 0.00 -1.00
2 WIND2 GUY 0.71 0.00 -1.00

3 DEAD GUY -0.15 0.00 -1.00


3 LIVE GUY -0.86 0.00 -1.00
3 WIND1 GUY -0.35 0.00 -1.00
DESIGN SHEET Page 37 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


3 WIND2 GUY 0.71 0.00 -1.00

STATIC 4 DEAD

*LOADCOND
@RDS 1.00 1.00 DEAD + 1.00 COLL + 1.00 LIVE
@RDS 1.00 1.00 DEAD + 1.00 COLL + 0.75 LIVE + 0.75 WIND
@RDS 1.00 1.00 DEAD + 1.00 COLL + 1.00 WIND
@RDS 1.00 0.60 DEAD + 1.00 WIND

*END
DESIGN SHEET Page 38 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

ROOF-PURLIN OUTPUT
** Front Page .....

ZAMIL STEEL INDUSTRIES


P.O.Box 877
Dammam 31421
Kingdom of Saudi Arabia

A S F A D
Advanced Steel Frame Analysis & Design
Version No. 1911.169 Nov 2019
Founded(1995) by: K.R.Ezzat
Developed by: Engineering Systems Dept.

File Name : C:\Users\sv4012\Desktop\N2-6284\ASFAD\PURLIN.puout


Run By : PLT
Date : 23-12-2019 at 15:18
Design Code : AISI-01

Units : Metric
DESIGN SHEET Page 39 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Modulus of Elasticity : 20300.00 kN/cm2
Coefficient of Expansion : 0.0000117

Steel Density : 7850.00 Kg/m3


Segment Size : 0.10 m

Page Size : 66

...........................................................................................

Purlin Input Report


Page Number.. 1
N4-5831-B01-A01-CO#00 *** ROOF PURLIN (ZONE 1,2) *** 15:18 23-12-2019
----------------------------------------------------------------------------------------

*HEADER
TITLE: N4-5831-B01-A01-CO#00 *** ROOF PURLIN (ZONE 1,2) ***
INIT: PLT
CONST: PAGE=66 CODE=AISI01 SEGMENT=0.10
OUTPUT: -I -D

*OPTIONS
POSDEF: 120
NEGDEF: 150
STDSEC: 202
STDLAP: 104
BWIDTH: 125
MINSEC: 0
CURSEC: 0
ESTRUT: 0
FLUSHB: 1
SUPPOB: 1
BFLBRC: 0
FUNBRC: 0
USRLAP: 0
MAX-UC: 0.90

*SPANS
1 8.000 Z-200X17 FLUSH LAP385 0 0 -1.0
2 8.000 Z-200X17 LAP385 LAP385 0 0 -1.0
3 8.000 Z-200X17 LAP385 FLUSH 0 0 -1.0

*LOADS
//ASCE7-05
//DL = 0.1 ; LL= 0.57 ; COLL =0.05 ; Q = 0.48 ; TRI = 1.5M
////GCP +GCPI GCP -GCPI
/ZONE 1-3(+) 0.48
/ZONE 1(-) -0.98
/ZONE 2(-) -1.38
/ZONE 3(-) -2.18
1 COLL GUY 0.0 -0.08 -1.00
2 COLL GUY 0.0 -0.08 -1.00
3 COLL GUY 0.0 -0.08 -1.00
1 DEAD GUY -0.15 0.00 -1.00
1 LIVE GUY -0.86 0.00 -1.00
1 WIND1 GUY -0.35 0.00 -1.00
1 WIND2 GUY 0.71 0.00 -1.00
DESIGN SHEET Page 40 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


2 DEAD GUY -0.15 0.00 -1.00
2 LIVE GUY -0.86 0.00 -1.00
2 WIND1 GUY -0.35 0.00 -1.00
2 WIND2 GUY 0.71 0.00 -1.00
3 DEAD GUY -0.15 0.00 -1.00
3 LIVE GUY -0.86 0.00 -1.00
3 WIND1 GUY -0.35 0.00 -1.00
3 WIND2 GUY 0.71 0.00 -1.00
STATIC 4 DEAD

*LOADCOND
@RDS 1.00 1.00 DEAD + 1.00 COLL + 1.00 LIVE
@RDS 1.00 1.00 DEAD + 1.00 COLL + 0.75 LIVE + 0.75 WIND
@RDS 1.00 1.00 DEAD + 1.00 COLL + 1.00 WIND
@RDS 1.00 0.60 DEAD + 1.00 WIND

...........................................................................................

Purlin Input Report


Page Number.. 2
N4-5831-B01-A01-CO#00 *** ROOF PURLIN (ZONE 1,2) *** 15:18 23-12-2019
----------------------------------------------------------------------------------------

*END

...........................................................................................

Short Summary Report based on AISI-01


Page Number.. 3
N4-5831-B01-A01-CO#00 *** ROOF PURLIN (ZONE 1,2) *** 15:18 23-12-2019
----------------------------------------------------------------------------------------

Section Section Unity Check Ratios Def.


Span No. Size (AX+BM) Shear Crip. (SF+BM) (CR+BM) Chk. | UC
----------------------------------------------------------------------------------------

01 1 Z-200X17 0.83 0.27 0.59 0.69 0.55 0.78 Pass


01 2 Z-200X17 + Z-200X17 0.52 0.14 0.47 0.29 0.69 0.05 Pass

02 1 Z-200X17 + Z-200X17 0.52 0.12 0.47 0.28 0.69 0.03 Pass


02 2 Z-200X17 0.81 0.22 0.00 0.71 0.54 0.06 Pass
02 3 Z-200X17 + Z-200X17 0.52 0.12 0.47 0.28 0.69 0.03 Pass

03 1 Z-200X17 + Z-200X17 0.52 0.14 0.47 0.29 0.69 0.05 Pass


03 2 Z-200X17 0.83 0.27 0.59 0.69 0.55 0.78 Pass

-----------------------------
Purlin Weight = 120.57 Kg
DESIGN SHEET Page 41 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

SIDE WALL -GIRT


*HEADER
Title: N2-6284-B02-A01-REV00 *** SW GIRT (ZONE 4,5) ***
Init: PLT
CONST: Page=66 Code=AISI01 Segment=0.10 Grade=SS340
OUTPUT: -I -D -C

*OPTIONS
POSDEF: 90
NEGDEF: 90
STDSEC: 202
STDLAP: 104
BWIDTH: 125
MINSEC: 0
CURSEC: 0
ESTRUT: 0
FLUSHB: 1
SUPPOB: 1
BFLBRC: 0
FUNBRC: 0
USRLAP: 0
MAX-UC: 0.90
NUMBRC: 3

*SPANS
1 8.000 Z-200X20 Flush Flush 0 0 -1.0 -1

*LOADS
//Q = 0.48 ; TRI = 1.5M
1 WINS GUY 0.69 0.00 -1.00
1 WINP GUY -0.62 0.00 -1.00

STATIC 4

*LOADCOND

@RDS 1.00 1.00 WINS


DESIGN SHEET Page 42 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


@RDS 1.00 1.00 WINP

*END

SIDE WALL -GIRT OUTPUT


** Front Page .....

ZAMIL STEEL INDUSTRIES


P.O.Box 877
Dammam 31421
Kingdom of Saudi Arabia

A S F A D
Advanced Steel Frame Analysis & Design
Version No. 1911.169 Nov 2019
Founded(1995) by: K.R.Ezzat
Developed by: Engineering Systems Dept.
DESIGN SHEET Page 43 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

File Name : C:\Users\sv4012\Desktop\N2-6284\ASFAD\SW GIRT.puout


Run By : PLT
Date : 24-12-2019 at 17:11
Design Code : AISI-01

Units : Metric
Modulus of Elasticity : 20300.00 kN/cm2
Coefficient of Expansion : 0.0000117

Steel Density : 7850.00 Kg/m3


Segment Size : 0.10 m

Page Size : 66

...........................................................................................

Purlin Input Report


Page Number.. 1
N2-6284-B02-A01-REV00 *** SW GIRT (ZONE 4,5) *** 17:11 24-12-2019
----------------------------------------------------------------------------------------

*HEADER
TITLE: N2-6284-B02-A01-REV00 *** SW GIRT (ZONE 4,5) ***
INIT: PLT
CONST: PAGE=66 CODE=AISI01 SEGMENT=0.10 GRADE=SS340
OUTPUT: -I -D -C

*OPTIONS
POSDEF: 90
NEGDEF: 90
STDSEC: 202
STDLAP: 104
BWIDTH: 125
MINSEC: 0
CURSEC: 0
ESTRUT: 0
FLUSHB: 1
SUPPOB: 1
BFLBRC: 0
FUNBRC: 0
USRLAP: 0
MAX-UC: 0.90
NUMBRC: 3

*SPANS
1 8.000 Z-200X20 FLUSH FLUSH 0 0 -1.0 -1

*LOADS
//Q = 0.48 ; TRI = 1.5M
1 WINS GUY 0.69 0.00 -1.00
DESIGN SHEET Page 44 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


1 WINP GUY -0.62 0.00 -1.00
STATIC 4

*LOADCOND
@RDS 1.00 1.00 WINS
@RDS 1.00 1.00 WINP

*END

...........................................................................................

Short Summary Report based on AISI-01


Page Number.. 2
N2-6284-B02-A01-REV00 *** SW GIRT (ZONE 4,5) *** 17:11 24-12-2019
----------------------------------------------------------------------------------------

Section Section Unity Check Ratios Def.


Span No. Size (AX+BM) Shear Crip. (SF+BM) (CR+BM) Chk. | UC
----------------------------------------------------------------------------------------

01 1 Z-200X20 0.83 0.11 0.34 0.49 0.47 0.51 Pass

-----------------------------------------------------------------------------------------
Purlin Weight = 43.33 Kg

PORTAL FRAME
*HEADER
VERSION: 1208129
TITLE: *** PORTAL ***
INIT: PLT
CONST: Page=66 Fy=34.50 Fp=0.75 Fc=2.50U Segment=0.60 Bolt=A325-36SH Moment=0.50 Fbrac=0
CONST: Kc=1
OUTPUT: -I -R D CQ -FC -FM -FP T -M U E4

*SPANS
8.000
EH 4.380

*MEMBERS
/COL 1-2
200.00 Slope=0.000 Ht=0.00 Girt=000.0 Disp=0.000 Fy=34.50 Fix=NT Conn=0
300.00 125.00X05.00 4.00 125.00X05.00 0.000
Bracing

/RAF 2-3
200.00 Slope=0.00 Purlin=000.0 End=0.000 Rel=NN Conn=1-2
200.00 175.00X06.00 4.00 175.00X06.00 0.000
Bracing

/COL 4-3
200.00 Slope=0.000 Ht=0.00 Girt=000.0 Disp=0.000 Fy=34.50 Fix=NT Conn=0
300.00 125.00X05.00 4.00 125.00X05.00 0.000
Bracing
DESIGN SHEET Page 45 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

*LOADS
DEAD 0.01
LIVE 0.01
COLL 0.00
BAY 0.01
WIND D=BFS 110 CA705 SFIB

2 1 WIND1 GCX 10.87 0.00


3 4 WIND2 GCX -10.87 0.00

STATIC 4 DEAD
*LOADCOND
@RDS 1.00 1.00 DEAD + 1.00 LIVE
@RDS 1.00 1.00 DEAD + 1.00 WIND

*AUTODESIGN
Vert-Def 180.00
Sway-Def 45.00

#StdAll BC
#DwRatio 4.000
#MinThk 0 0
#Max_Kw 180.000
#Max_Kb 34.000
#Max_Uc 0.85
#Max_LR 0

*END

PORTAL FRAME OUTPUT


** Front Page [MAC-ON] .....

ZAMIL STEEL INDUSTRIES


P.O.Box 877
Dammam 31421
Kingdom of Saudi Arabia

A S F A D
Advanced Steel Frame Analysis & Design
DESIGN SHEET Page 46 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Version No. 1911.169 Nov 2019
Founded(1995) by: K.R.Ezzat
Developed by: Engineering Systems Dept.

File Name : C:\Users\sv4012\Desktop\N2-6284\ASFAD\PORTAL.out


Run By : PLT
Date : 24-12-2019 at 12:46
Design Code : [AISC-89]

Units : Metric
Modulus of Elasticity : 19995.00 kN/cm2
Coefficient of Expansion : 0.0000117

Concrete Bearing Stress : 0.75 kN/cm2


Steel Density : 7850.00 Kg/m3
Segment Size : 0.60 m

Page Size : 66

...........................................................................................

Macro Input Report


Page Number.. 1
PORTAL *** 12:46 24-12-2019
----------------------------------------------------------------------------------------

*HEADER
VERSION: 1208129
TITLE: *** PORTAL ***
INIT: PLT
CONST: PAGE=66 FY=34.50 FP=0.75 FC=2.50U SEGMENT=0.60 BOLT=A325-36SH MOMENT=0.50 FBRAC=0
CONST: KC=1
OUTPUT: -I -R D CQ -FC -FM -FP T -M U E4

*SPANS
8.000
EH 4.380

*MEMBERS
/COL 1-2
200.00 SLOPE=0.000 HT=0.00 GIRT=000.0 DISP=0.000 FY=34.50 FIX=NT CONN=0
300.00 125.00X05.00 4.00 125.00X05.00 0.000
BRACING
/RAF 2-3
DESIGN SHEET Page 47 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


200.00 SLOPE=0.00 PURLIN=000.0 END=0.000 REL=NN CONN=1-2
200.00 175.00X06.00 4.00 175.00X06.00 0.000
BRACING
/COL 4-3
200.00 SLOPE=0.000 HT=0.00 GIRT=000.0 DISP=0.000 FY=34.50 FIX=NT CONN=0
300.00 125.00X05.00 4.00 125.00X05.00 0.000
BRACING

*LOADS
DEAD 0.01
LIVE 0.01
COLL 0.00
BAY 0.01
WIND D=BFS 110 CA705 SFIB
2 1 WIND1 GCX 10.87 0.00
3 4 WIND2 GCX -10.87 0.00
STATIC 4 DEAD

*LOADCOND
@RDS 1.00 1.00 DEAD + 1.00 LIVE
@RDS 1.00 1.00 DEAD + 1.00 WIND

*AUTODESIGN
VERT-DEF 180.00
SWAY-DEF 45.00
#STDALL BC
#DWRATIO 4.000
#MINTHK 0 0
#MAX_KW 180.000
#MAX_KB 34.000
#MAX_UC 0.85
#MAX_LR 0

*END
.
.** Errors Log **
.
.
.** Processed with No Errors **

...........................................................................................

Design Summary Report based on AISC-89


Page Number.. 1
PORTAL *** 12:46 24-12-2019
----------------------------------------------------------------------------------------

****************************************************************************************
Member 1 - 2 Length = 4.274 meters Fy = 34.50 kN/cm2 Weight = 75.667 Kg
****************************************************************************************

Web Depth Top Flange Web Bottom Flange


Section Length (....mm....) Section (.....mm.....) thick (.....mm.....) Unity
No. (m) Start End type width x thick (mm) width x thick Check
---- ------- --------------- ------- ---------------- ------ ---------------- -----
1 4.274 200.00 300.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00 Pass
DESIGN SHEET Page 48 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Maximum Forces Allowable Stresses Calculated Stresses
Section Moment Axial @ Dist Load (......kN/cm2.....) (......kN/cm2.....) Stress
No. (kN.m) (kN) (m) cond Fa Fb-Top Fb-Bott fa fb-Top fb-Bott Ratio
---- ---------------------------- --------------------- --------------------- -------
1 -23.16 -6.91 4.16 4 3.95 20.70 11.67 -0.28 9.43 -9.43 0.88

Section Maximum Allow. Calcu. Max + Deflection Max - Deflection


No. Shear @ Dist Load Fv fv Stress Def. @ Dist Load Def. @ Dist Load
(kN) (m) cond (...kN/cm2..) Ratio (cm) (m) cond (cm) (m) cond
---- -------------------- ------ ------ ------ ------------------ ------------------
1 5.56 0.00 4 13.80 0.69 0.05 4.63 4.16 4 -4.64 4.16 2

****************************************************************************************
Member 2 - 3 Length = 7.690 meters Fy = 34.50 kN/cm2 Weight = 175.063 Kg
****************************************************************************************

Web Depth Top Flange Web Bottom Flange


Section Length (....mm....) Section (.....mm.....) thick (.....mm.....) Unity
No. (m) Start End type width x thick (mm) width x thick Check
---- ------- --------------- ------- ---------------- ------ ---------------- -----
1 7.690 200.00 200.00 I-00 175.00 x 6.00 4.00 175.00 x 6.00 Pass

Maximum Forces Allowable Stresses Calculated Stresses


Section Moment Axial @ Dist Load (......kN/cm2.....) (......kN/cm2.....) Stress
No. (kN.m) (kN) (m) cond Fa Fb-Top Fb-Bott fa fb-Top fb-Bott Ratio
---- ---------------------------- --------------------- --------------------- -------
1 -22.75 -5.65 7.54 4 3.48 20.70 12.75 -0.19 9.66 -9.66 0.81

Section Maximum Allow. Calcu. Max + Deflection Max - Deflection


No. Shear @ Dist Load Fv fv Stress Def. @ Dist Load Def. @ Dist Load
(kN) (m) cond (...kN/cm2..) Ratio (cm) (m) cond (cm) (m) cond
---- -------------------- ------ ------ ------ ------------------ ------------------
1 6.79 0.15 4 13.80 0.85 0.06 0.43 1.73 2 -0.51 1.73 4
----------------------------------------------------------------------------------------

...........................................................................................

Design Summary Report based on AISC-89


Page Number.. 2
PORTAL *** 12:46 24-12-2019
----------------------------------------------------------------------------------------

****************************************************************************************
Member 4 - 3 Length = 4.274 meters Fy = 34.50 kN/cm2 Weight = 75.667 Kg
****************************************************************************************

Web Depth Top Flange Web Bottom Flange


Section Length (....mm....) Section (.....mm.....) thick (.....mm.....) Unity
No. (m) Start End type width x thick (mm) width x thick Check
---- ------- --------------- ------- ---------------- ------ ---------------- -----
1 4.274 200.00 300.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00 Pass

Maximum Forces Allowable Stresses Calculated Stresses


Section Moment Axial @ Dist Load (......kN/cm2.....) (......kN/cm2.....) Stress
No. (kN.m) (kN) (m) cond Fa Fb-Top Fb-Bott fa fb-Top fb-Bott Ratio
---- ---------------------------- --------------------- --------------------- -------
1 23.16 -6.91 4.16 4 3.95 11.67 20.70 -0.28 -9.43 9.43 0.88
DESIGN SHEET Page 49 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

Section Maximum Allow. Calcu. Max + Deflection Max - Deflection


No. Shear @ Dist Load Fv fv Stress Def. @ Dist Load Def. @ Dist Load
(kN) (m) cond (...kN/cm2..) Ratio (cm) (m) cond (cm) (m) cond
---- -------------------- ------ ------ ------ ------------------ ------------------
1 5.56 0.00 4 13.80 0.69 0.05 4.64 4.16 2 -4.63 4.16 4
----------------------------------------------------------------------------------------
Frame Weight = 326.4 Kg Surface Area = 18.1 m2 ( 46.3 m2/Ton)
Conn. Weight = 58.4 Kg

...........................................................................................

Unity Check AISC-89 & Deflection Summary Report


Page Number.. 3
PORTAL *** 12:46 24-12-2019
----------------------------------------------------------------------------------------

Section Length Shear AX+BM Max + Def Max - Def Check


No. (m) Cond Uc Cond Uc Cond (cm) Cond (cm)
-----------------------------------------------------------------------------------
Member 1 - 2 1 4.274 | 4 0.05 4 0.88 | 4 4.63 2 -4.64 | Pass > User max UC
-----------------------------------------------------------------------------------
Member 2 - 3 1 7.690 | 4 0.06 4 0.81 | 2 0.43 4 -0.51 | Pass
-----------------------------------------------------------------------------------
Member 4 - 3 1 4.274 | 4 0.05 4 0.88 | 2 4.64 4 -4.63 | Pass > User max UC
-----------------------------------------------------------------------------------

...........................................................................................

Connections Summary Report based on AISC-89


Page Number.. 4
PORTAL *** 12:46 24-12-2019
----------------------------------------------------------------------------------------

********************************************************************************
Connection Type : Knee Joints [ 3 2 1 ] Member 3 - 2
********************************************************************************

Section dimensions :
Web Top/Outer Flange Bot/inner Flange
(.....mm......) (.....mm......) (.....mm......)
--------------- ---------------- ----------------
sec @ conn member 200.00 x 4.00 175.00 x 6.00 175.00 x 6.00
sec @ other member 300.00 x 4.00 125.00 x 5.00 125.00 x 5.00

Controlling Forces :
Moment Axial Load Shear 50% Section
kN.m kN Cond kN Capac. kN.m
-------- -------- ---- ------- -------------
-22.75 -5.65 4 6.79 24.36
21.61 -5.56 2 6.79 24.36

Connection Design :

Bolts conforming to ASTM A-325

Top/Outer Bolts 2 Rows (1 Outside) x 2 = 4 size 20.00 mm


DESIGN SHEET Page 50 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Bot/Inner Bolts 1 Rows (0 Outside) x 2 = 2 size 20.00 mm

Total Bolts 3 Rows (1 Outside) x 2 = 6 size 20.00 mm

End plate size 200 x 340 x 20 mm Fy = 34.50 kN/cm2

No. of Top/Outer Stiffeners = 0


No. of Bot/Inner Stiffeners = 0

Knee Web of 4.00 mm is O.K.

Actual Allowable
kN kN Ratio
--------- --------- -----
Top/Outer Bolt Tension 28.60 95.28 0.30
Bot/Inner Bolt Tension 74.73 95.28 0.78

Top/Outer Plate Moment 3.07 17.25 0.18


Bot/Inner Plate Moment 12.85 17.25 0.75

Average Bolt Shear 1.13 45.46 0.02


Top Bolt Combined TQ (Bot full Q loaded) 0.00
Bot Bolt Combined TQ (Top full Q loaded) 0.00

Knee Web Plate Shear 10.23 13.80 0.74

Standard Connection Code ## V04220 -20 ##

--------------------------------------------------------------------------------

...........................................................................................

Connections Summary Report based on AISC-89


Page Number.. 5
PORTAL *** 12:46 24-12-2019
----------------------------------------------------------------------------------------

********************************************************************************
Connection Type : Knee Joints [ 2 3 4 ] Member 2 - 3
********************************************************************************

Section dimensions :
Web Top/Outer Flange Bot/inner Flange
(.....mm......) (.....mm......) (.....mm......)
--------------- ---------------- ----------------
sec @ conn member 200.00 x 4.00 175.00 x 6.00 175.00 x 6.00
sec @ other member 300.00 x 4.00 125.00 x 5.00 125.00 x 5.00

Controlling Forces :
Moment Axial Load Shear 50% Section
kN.m kN Cond kN Capac. kN.m
-------- -------- ---- ------- -------------
-22.75 -5.65 4 6.79 24.36
21.61 -5.56 2 6.79 24.36

Connection Design :
DESIGN SHEET Page 51 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Bolts conforming to ASTM A-325

Top/Outer Bolts 2 Rows (1 Outside) x 2 = 4 size 20.00 mm


Bot/Inner Bolts 1 Rows (0 Outside) x 2 = 2 size 20.00 mm

Total Bolts 3 Rows (1 Outside) x 2 = 6 size 20.00 mm

End plate size 200 x 340 x 20 mm Fy = 34.50 kN/cm2

No. of Top/Outer Stiffeners = 0


No. of Bot/Inner Stiffeners = 0

Knee Web of 4.00 mm is O.K.

Actual Allowable
kN kN Ratio
--------- --------- -----
Top/Outer Bolt Tension 28.60 95.28 0.30
Bot/Inner Bolt Tension 74.73 95.28 0.78

Top/Outer Plate Moment 3.07 17.25 0.18


Bot/Inner Plate Moment 12.85 17.25 0.75

Average Bolt Shear 1.13 45.46 0.02


Top Bolt Combined TQ (Bot full Q loaded) 0.00
Bot Bolt Combined TQ (Top full Q loaded) 0.00

Knee Web Plate Shear 10.23 13.80 0.74

Standard Connection Code ## V04220 -20 ##

--------------------------------------------------------------------------------

...........................................................................................

Connections Summary Report based on AISC-89


Page Number.. 6
PORTAL *** 12:46 24-12-2019
----------------------------------------------------------------------------------------

********************************************************************************
Connection Type : Pinned Base at Joint 1 Member 1 - 2
********************************************************************************

Section dimensions :
Web Top/Outer Flange Bot/inner Flange
(.....mm......) (.....mm......) (.....mm......)
--------------- ---------------- ----------------
sec @ Connection 200.00 x 4.00 125.00 x 5.00 125.00 x 5.00

Controlling Forces :
Moment Vert. Load Horiz.
kN.m kN Cond kN
-------- -------- ---- -------
0.00 5.00 2 5.65
-0.00 -7.56 4 5.65
DESIGN SHEET Page 52 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Connection Design :

Bolts conforming to ASTM F-1554 Gr 36 - SH25UD

Anchor bolts 1 Rows (all inside) x 2 = 2 size 20.00 mm

Base plate size 225 x 245 x 12 mm Fy = 34.50 kN/cm2

Actual Allowable
kN kN Ratio
--------- --------- -----
Anchor Bolt Tension 2.50 41.47 0.06
Bearing stress /cm2 0.01 0.91 0.02
Base Plate Moment 0.54 6.21 0.09
Average Bolt Shear 2.82 21.36 0.13
Bolt Combined TQ 0.14
Web Yield Check 0.05

Standard Connection Code ## BR220-12 ##

--------------------------------------------------------------------------------

...........................................................................................

Connections Summary Report based on AISC-89


Page Number.. 7
PORTAL *** 12:46 24-12-2019
----------------------------------------------------------------------------------------

********************************************************************************
Connection Type : Pinned Base at Joint 4 Member 4 - 3
********************************************************************************

Section dimensions :
Web Top/Outer Flange Bot/inner Flange
(.....mm......) (.....mm......) (.....mm......)
--------------- ---------------- ----------------
sec @ Connection 200.00 x 4.00 125.00 x 5.00 125.00 x 5.00

Controlling Forces :
Moment Vert. Load Horiz.
kN.m kN Cond kN
-------- -------- ---- -------
-0.00 5.00 2 5.65
0.00 -7.56 4 5.65

Connection Design :

Bolts conforming to ASTM F-1554 Gr 36 - SH25UD

Anchor bolts 1 Rows (all inside) x 2 = 2 size 20.00 mm

Base plate size 225 x 245 x 12 mm Fy = 34.50 kN/cm2

Actual Allowable
kN kN Ratio
--------- --------- -----
DESIGN SHEET Page 53 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Anchor Bolt Tension 2.50 41.47 0.06
Bearing stress /cm2 0.01 0.91 0.02
Base Plate Moment 0.54 6.21 0.09
Average Bolt Shear 2.82 21.36 0.13
Bolt Combined TQ 0.14
Web Yield Check 0.05

Standard Connection Code ## BR220-12 ##

--------------------------------------------------------------------------------
END WALL RAFTER
*HEADER
VERSION: 1604143
TITLE: N2-6284-B01-A01-R01 *** ENDWALL RAFTER @ GL. 1,13
INIT: PLT
CONST: Page=66 Fy=34.50 Fc=2.50U PP=0 Segment=0.60 Bolt=A325-36SV Moment=0.50 Fbrac=0
CONST: MinABolt=0-4 MinBolt=1-5
OUTPUT: I R D C -FC -FM -FP T -M U E4

*NODES
1 0.000 0.000
2 6.040 0.680

*SUPPORTS
1 X Y
2 Y

*MEMBERS
//EC1
1 2 0.00 0.00 NNN NNN
200 200 125.00x5.00 4.00 125.00x05.00 0.00 I
Bracing 1.5T 3T 4.5T 6t

*LOADS
1 2 DEAD GWY -1.000
G ALL
1 2 DEAD GUY -0.4
1 2 COLL GUY -0.2
1 2 LIVE GUY -2.28
//WIND SPEED = 110 KM/H,, WL = 0.48 KN/M2.
1 2 WINDP LUY -0.72
1 2 WINDS LUY -2.45

STATIC 4
STATIC DEAD

*LOADCOND

@RDS 1.00 1.00 DEAD + 1.00 COLL + 1.00 LIVE


@RDS 1.00 1.00 DEAD + 1.00 COLL + 0.75 LIVE + 0.75 WIND
@RDS 1.00 1.00 DEAD + 1.00 COLL + 1.00 WIND
@RDS 1.00 0.60 DEAD + 1.00 WIND

*DESIGN
1 2 KX=1.0 KY=1.0 FY=34.50
DESIGN SHEET Page 54 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


*CONNECTIONS
SN 1 2
EN 1 2
*GEOM
#Uni-Dsn 1
#StdAll BC
#DWRATIO 4.000
#MINTHK 0 0
#Max_Kw 180.000
#Max_Kb 34.000
#Max_Uc 0.900
#Max_LR 0

*END
END WALL RAFTER-OUTPUT

** Front Page [DET] .....

ZAMIL STEEL INDUSTRIES


P.O.Box 877
Dammam 31421
Kingdom of Saudi Arabia

A S F A D
Advanced Steel Frame Analysis & Design
Version No. 1911.169 Nov 2019
Founded(1995) by: K.R.Ezzat
Developed by: Engineering Systems Dept.
DESIGN SHEET Page 55 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

File Name : C:\Users\sv4012\Desktop\N2-6284\ASFAD\EW RAFTER.out


Run By : PLT
Date : 24-12-2019 at 09:52
Design Code : [AISC-89]

Units : Metric
Modulus of Elasticity : 19995.00 kN/cm2
Coefficient of Expansion : 0.0000117

Concrete Bearing Stress : -1.00 kN/cm2


Steel Density : 7850.00 Kg/m3
Segment Size : 0.60 m

Page Size : 66

...........................................................................................

Detail Input Report


Page Number.. 1
N2-6284-B01-A01-R01 *** ENDWALL RAFTER @ GL. 1,13 09:52 24-12-2019
----------------------------------------------------------------------------------------

*HEADER
VERSION: 1604143
TITLE: N2-6284-B01-A01-R01 *** ENDWALL RAFTER @ GL. 1,13
INIT: PLT
CONST: PAGE=66 FY=34.50 FC=2.50U PP=0 SEGMENT=0.60 BOLT=A325-36SV MOMENT=0.50 FBRAC=0
CONST: MINABOLT=0-4 MINBOLT=1-5
OUTPUT: I R D C -FC -FM -FP T -M U E4

*NODES
1 0.000 0.000
2 6.040 0.680

*SUPPORTS
1 X Y
2 Y

*MEMBERS
//EC1
1 2 0.00 0.00 NNN NNN
200 200 125.00X5.00 4.00 125.00X05.00 0.00 I
BRACING 1.5T 3T 4.5T 6T

*LOADS
1 2 DEAD GWY -1.000
G ALL
1 2 DEAD GUY -0.4
1 2 COLL GUY -0.2
1 2 LIVE GUY -2.28
//WIND SPEED = 110 KM/H,, WL = 0.48 KN/M2.
1 2 WINDP LUY -0.72
1 2 WINDS LUY -2.45
STATIC 4
STATIC DEAD

*LOADCOND
DESIGN SHEET Page 56 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


@RDS 1.00 1.00 DEAD + 1.00 COLL + 1.00 LIVE
@RDS 1.00 1.00 DEAD + 1.00 COLL + 0.75 LIVE + 0.75 WIND
@RDS 1.00 1.00 DEAD + 1.00 COLL + 1.00 WIND
@RDS 1.00 0.60 DEAD + 1.00 WIND

*DESIGN
1 2 KX=1.0 KY=1.0 FY=34.50

*CONNECTIONS
SN 1 2
EN 1 2

*GEOM
#UNI-DSN 1
#STDALL BC
#DWRATIO 4.000
#MINTHK 0 0
#MAX_KW 180.000
#MAX_KB 34.000
#MAX_UC 0.900
#MAX_LR 0

*END
.
.** Errors Log **

...........................................................................................

Detail Input Report


Page Number.. 2
N2-6284-B01-A01-R01 *** ENDWALL RAFTER @ GL. 1,13 09:52 24-12-2019
----------------------------------------------------------------------------------------

.
.
.** Processed with No Errors **

...........................................................................................

Input Details Report


Page Number.. 1
N2-6284-B01-A01-R01 *** ENDWALL RAFTER @ GL. 1,13 09:52 24-12-2019
----------------------------------------------------------------------------------------

Coordinates Restraints Elastic Restraint Coeff.


Node X Y X Y M X Y M
No. (.....meters....) (Y=Rest. E=Elas.) kN/m kN/m kN.m/deg
---- ----------------- ----------------- ------------------------------

1 0.000 0.000 Y Y
2 6.040 0.680 Y

Offsets Releases
Member No of Start End Start End
No. Start End Sections (.....m.....) X Y M X Y M
------------- -------- ------------- ------------
DESIGN SHEET Page 57 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

1 1 - 2 1 0.00 0.00

Web Depth Top Flange Web Bottom Flange


Section Length (....mm....) Section (.....mm.....) thick (.....mm.....)
Member No. (m) Start End type width x thick (mm) width x thick
--------- ---- ------- --------------- ------- ---------------- ------ ----------------

1 - 2 1 6.078 200.00 200.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00

Member Bracings (distance ..meters , T:Top Flg - B:Bottom Flg - D:Double both Flgs)
--------- ------------------------------------------------------------------------------

1 - 2 1.50T 3.00T 3.04N 4.50T 6.00T

...........................................................................................

Input Details Report


Page Number.. 2
N2-6284-B01-A01-R01 *** ENDWALL RAFTER @ GL. 1,13 09:52 24-12-2019
----------------------------------------------------------------------------------------

Load Load Value Start/End Start & End Distances Angle


No. Member Type ( kN kN/m kN.m ) (..m.. '-' ratio of length) (Deg)
--- --------- ---- ---------------------- -----------------------------------

Load Case No. 1 DEAD

1 1 - 2 GWY -1.00 x Own WT from 0.00 to -1.00


2 1 - 2 GUY -0.40 from 0.00 to -1.00

Load Case No. 2 COLL

1 1 - 2 GUY -0.20 from 0.00 to -1.00

Load Case No. 3 LIVE

1 1 - 2 GUY -2.28 from 0.00 to -1.00

Load Case No. 4 WINDP

1 1 - 2 LUY -0.72 from 0.00 to -1.00

Load Case No. 5 WINDS

1 1 - 2 LUY -2.45 from 0.00 to -1.00

Static Load Cases :

1. Load Case No. 1 DEAD

Load Category No. 1 [Indiv.] COLL


DESIGN SHEET Page 58 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


1. Load Case No. 2 COLL

Load Category No. 2 [Indiv.] LIVE

1. Load Case No. 3 LIVE

Load Category No. 3 [Indiv.] WIND

1. Load Case No. 4 WINDP


2. Load Case No. 5 WINDS

Load Condition No. 1 @ RSD With 1.00 Stress Factor


1. 1.00 x DEAD
2. 1.00 x COLL
3. 1.00 x LIVE

Load Condition No. 2 @ RSD With 1.00 Stress Factor


1. 1.00 x DEAD
2. 1.00 x COLL

...........................................................................................

Input Details Report


Page Number.. 3
N2-6284-B01-A01-R01 *** ENDWALL RAFTER @ GL. 1,13 09:52 24-12-2019
----------------------------------------------------------------------------------------

Load Condition No. 2 @ RSD With 1.00 Stress Factor


3. 0.75 x LIVE
4. 0.75 x WIND

Load Condition No. 3 @ RSD With 1.00 Stress Factor


1. 1.00 x DEAD
2. 1.00 x COLL
3. 1.00 x WIND

Load Condition No. 4 @ RSD With 1.00 Stress Factor


1. 0.60 x DEAD
2. 1.00 x WIND

...........................................................................................

Reactions & Displacements Report


Page Number.. 4
N2-6284-B01-A01-R01 *** ENDWALL RAFTER @ GL. 1,13 09:52 24-12-2019
----------------------------------------------------------------------------------------

Structure Reactions and Displacements - Load Case no. 1...DEAD

Vertical Horizontal Moment Vertical Horizontal Rotation


DESIGN SHEET Page 59 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Node Reaction Reaction Reaction Displac. Displac. Angle
No. (kN) (kN) (kN.m) (cm) (cm) (deg)
---- ---------- ---------- ---------- ---------- ---------- ----------
1 1.695 -0.000 -0.000 0.000 0.000 -0.094
2 1.695 -0.000 -0.000 0.000 0.000 0.094

Structure Reactions and Displacements - Load Case no. 2...COLL

Vertical Horizontal Moment Vertical Horizontal Rotation


Node Reaction Reaction Reaction Displac. Displac. Angle
No. (kN) (kN) (kN.m) (cm) (cm) (deg)
---- ---------- ---------- ---------- ---------- ---------- ----------
1 0.608 -0.000 -0.000 0.000 0.000 -0.034
2 0.608 -0.000 0.000 0.000 0.000 0.034

Structure Reactions and Displacements - Load Case no. 3...LIVE

Vertical Horizontal Moment Vertical Horizontal Rotation


Node Reaction Reaction Reaction Displac. Displac. Angle
No. (kN) (kN) (kN.m) (cm) (cm) (deg)
---- ---------- ---------- ---------- ---------- ---------- ----------
1 6.929 -0.000 -0.000 0.000 0.000 -0.384
2 6.929 -0.000 -0.000 0.000 0.000 0.384

Structure Reactions and Displacements - Load Case no. 4...WINDP

Vertical Horizontal Moment Vertical Horizontal Rotation


Node Reaction Reaction Reaction Displac. Displac. Angle
No. (kN) (kN) (kN.m) (cm) (cm) (deg)
---- ---------- ---------- ---------- ---------- ---------- ----------
1 2.147 -0.490 0.000 0.000 0.000 -0.122
2 2.202 -0.000 -0.000 0.000 0.000 0.122

Structure Reactions and Displacements - Load Case no. 5...WINDS

Vertical Horizontal Moment Vertical Horizontal Rotation


Node Reaction Reaction Reaction Displac. Displac. Angle
No. (kN) (kN) (kN.m) (cm) (cm) (deg)
---- ---------- ---------- ---------- ---------- ---------- ----------
1 7.305 -1.666 -0.000 0.000 0.000 -0.415
2 7.493 -0.000 0.000 0.000 0.001 0.416

...........................................................................................

Reactions & Displacements Report


Page Number.. 5
N2-6284-B01-A01-R01 *** ENDWALL RAFTER @ GL. 1,13 09:52 24-12-2019
----------------------------------------------------------------------------------------

Structure Max Positive Reactions Structure Max Negative Reactions

Vertical Horizontal Moment Vertical Horizontal Moment


Node Reac. Load Reaction Reaction Reaction Load Reaction Reaction Reaction
No. Type Cond (kN) (kN) (kN.m) Cond (kN) (kN) (kN.m)
---- ---- ---- ---------- ---------- ---------- ---- ---------- ---------- ----------

1 H 0 -0.000 -0.000 -0.000 3 9.000 -1.666 -0.000


DESIGN SHEET Page 60 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


1 V 2 12.979 -1.250 -0.000 0 -0.000 -0.000 -0.000

2 V 2 13.119 -0.000 0.000 0 -0.000 -0.000 -0.000

...........................................................................................

Design Summary Report based on AISC-89


Page Number.. 6
N2-6284-B01-A01-R01 *** ENDWALL RAFTER @ GL. 1,13 09:52 24-12-2019
----------------------------------------------------------------------------------------

****************************************************************************************
Member 1 - 2 Length = 6.078 meters Fy = 34.50 kN/cm2 Weight = 97.813 Kg
****************************************************************************************

Web Depth Top Flange Web Bottom Flange


Section Length (....mm....) Section (.....mm.....) thick (.....mm.....) Unity
No. (m) Start End type width x thick (mm) width x thick Check
---- ------- --------------- ------- ---------------- ------ ---------------- -----
1 6.078 200.00 200.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00 216 S

Maximum Forces Allowable Stresses Calculated Stresses


Section Moment Axial @ Dist Load (......kN/cm2.....) (......kN/cm2.....) Stress
No. (kN.m) (kN) (m) cond Fa Fb-Top Fb-Bott fa fb-Top fb-Bott Ratio
---- ---------------------------- --------------------- --------------------- -------
1 19.81 0.63 3.04 2 20.70 20.63 20.70 0.03 -13.16 13.16 0.64

Section Maximum Allow. Calcu. Max + Deflection Max - Deflection


No. Shear @ Dist Load Fv fv Stress Def. @ Dist Load Def. @ Dist Load
(kN) (m) cond (...kN/cm2..) Ratio (cm) (m) cond (cm) (m) cond
---- -------------------- ------ ------ ------ ------------------ ------------------
1 13.04 0.00 2 13.80 1.63 0.12 0.00 0.00 0 -2.41 3.04 2
----------------------------------------------------------------------------------------
Frame Weight = 97.8 Kg Surface Area = 5.9 m2 ( 48.3 m2/Ton)
Conn. Weight = 22.7 Kg

...........................................................................................

Unity Check AISC-89 & Deflection Summary Report


Page Number.. 7
N2-6284-B01-A01-R01 *** ENDWALL RAFTER @ GL. 1,13 09:52 24-12-2019
----------------------------------------------------------------------------------------

Section Length Shear AX+BM Max + Def Max - Def Check


No. (m) Cond Uc Cond Uc Cond (cm) Cond (cm)
-----------------------------------------------------------------------------------
Member 1 - 2 1 6.078 | 2 0.12 2 0.64 | 0 0.00 2 -2.41 | 216 S
-----------------------------------------------------------------------------------

...........................................................................................

Connections Summary Report based on AISC-89


Page Number.. 8
N2-6284-B01-A01-R01 *** ENDWALL RAFTER @ GL. 1,13 09:52 24-12-2019
----------------------------------------------------------------------------------------
DESIGN SHEET Page 61 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


********************************************************************************
Connection Type : Splice at Start of Section 1 within Member 1 - 2
********************************************************************************

Section dimensions :
Web Top/Outer Flange Bot/inner Flange
(.....mm......) (.....mm......) (.....mm......)
--------------- ---------------- ----------------
sec @ Connection 200.00 x 4.00 125.00 x 5.00 125.00 x 5.00

Controlling Forces :
Moment Axial Load Shear 50% Section
kN.m kN Cond kN Capac. kN.m
-------- -------- ---- ------- -------------
0.00 0.72 4 13.04 15.58
0.00 0.72 4 13.04 15.58

Connection Design :

Bolts conforming to ASTM A-325

Top/Outer Bolts 1 Rows (0 Outside) x 2 = 2 size 16.00 mm


Bot/Inner Bolts 1 Rows (0 Outside) x 2 = 2 size 16.00 mm

Total Bolts 2 Rows (0 Outside) x 2 = 4 size 16.00 mm

End plate size 200 x 250 x 15 mm Fy = 34.50 kN/cm2

No. of Top/Outer Stiffeners = 0


No. of Bot/Inner Stiffeners = 0

Actual Allowable
kN kN Ratio
--------- --------- -----
Top/Outer Bolt Tension 47.93 60.98 0.79
Bot/Inner Bolt Tension 47.93 60.98 0.79

Top/Outer Plate Moment 8.44 9.70 0.87


Bot/Inner Plate Moment 8.44 9.70 0.87

Average Bolt Shear 3.26 29.09 0.11

Standard Connection Code ## RS2216 -15 ##

--------------------------------------------------------------------------------

...........................................................................................

Connections Summary Report based on AISC-89


Page Number.. 9
N2-6284-B01-A01-R01 *** ENDWALL RAFTER @ GL. 1,13 09:52 24-12-2019
----------------------------------------------------------------------------------------

********************************************************************************
Connection Type : Splice at End of Section 1 within Member 1 - 2
********************************************************************************
DESIGN SHEET Page 62 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Section dimensions :
Web Top/Outer Flange Bot/inner Flange
(.....mm......) (.....mm......) (.....mm......)
--------------- ---------------- ----------------
sec @ Connection 200.00 x 4.00 125.00 x 5.00 125.00 x 5.00

Controlling Forces :
Moment Axial Load Shear 50% Section
kN.m kN Cond kN Capac. kN.m
-------- -------- ---- ------- -------------
0.00 1.47 2 13.04 15.58
0.00 1.47 2 13.04 15.58

Connection Design :

Bolts conforming to ASTM A-325

Top/Outer Bolts 1 Rows (0 Outside) x 2 = 2 size 16.00 mm


Bot/Inner Bolts 1 Rows (0 Outside) x 2 = 2 size 16.00 mm

Total Bolts 2 Rows (0 Outside) x 2 = 4 size 16.00 mm

End plate size 200 x 250 x 15 mm Fy = 34.50 kN/cm2

No. of Top/Outer Stiffeners = 0


No. of Bot/Inner Stiffeners = 0

Actual Allowable
kN kN Ratio
--------- --------- -----
Top/Outer Bolt Tension 47.93 60.98 0.79
Bot/Inner Bolt Tension 47.93 60.98 0.79

Top/Outer Plate Moment 8.44 9.70 0.87


Bot/Inner Plate Moment 8.44 9.70 0.87

Average Bolt Shear 3.26 29.09 0.11

Standard Connection Code ## RS2216 -15 ##

--------------------------------------------------------------------------------

END COLUMN
*HEADER
VERSION: 1604143
TITLE: N2-6284-B01-A01-R00 *** ENDWALL COLUMN : GL. 13
INIT: PLT
CONST: Page=66 Fy=34.50 Fb=1.00 PP=0 Segment=0.60 Bolt=A325-36SV Moment=0.50 Fbrac=0
CONST: MinABolt=0-4 MinBolt=1-5
OUTPUT: I R D C -FC -FM -FP T -M U E4

*NODES
3 4.000 1.000
4 4.000 4.100

5 8.000 1.000
6 8.000 4.959
DESIGN SHEET Page 63 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


*SUPPORTSDF
3 X Y
4 X
5 X Y
6 X

*MEMBERS

3 4 0.00 0.00 NNN NNN


200.00 200.00 125.00x05.00 4.00 125.00x05.00 0.00 I
Bracing 1.7D 3.4T 5.10D 6.80T

5 6 0.00 0.00 NNN NNN


200.00 200.00 125.00x05.00 4.00 125.00x05.00 0.00 I
Bracing 1.7D 3.4T 5.10D 6.80T

*LOADS
3 4 DEAD GWY -1.00 0.00 -1.00
5 6 DEAD GWY -1.00 0.00 -1.00
G ALL
//EC1
/WIND PRESSURE Q = 0.48 KN/M2 ; TRI = 3M , CP=0.9

///
3 4 WINDP GUX 1.166 0.00 -1.00
3 4 WINDS GUX -1.296 0.00 -1.00
/TRI =6M

5 6 WINDP GUX 2.333 0.00 -1.00


5 6 WINDS GUX -2.592 0.00 -1.00

/EWR
//
4 3 DEAD GCY -1,695 0,00
4 3 COLL GCY -0,608 0,00
4 3 LIVE GCY -6,929 0,00
4 3 WINDP GCY -2,147 0,00
4 3 WINDP GCX 0,490 0,00
4 3 WINDS GCY -7,305 0,00
4 3 WINDS GCX 1,666 0,00
//
//
6 5 DEAD GCY -1,695 0,00
6 5 COLL GCY -0,608 0,00
6 5 LIVE GCY -6,929 0,00
6 5 WINDP GCY -2,147 0,00
6 5 WINDP GCX 0,490 0,00
6 5 WINDS GCY -7,305 0,00
6 5 WINDS GCX 1,666 0,00
//
STATIC 4 DEAD

*LOADCOND

@RDS 1.00 0.60 DEAD + 1.00 WIND


DESIGN SHEET Page 64 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


*DESIGN
1 2 KX=1.00 OFF-KX=0.00 KY=1.00 FY=34.50 CB=0.00 CM=-1.00 A/H=5.00 LY-EXT=0

*CONNECTIONS
P 3 4 BR420-12
P 5 6 BR420-12
*GEOM
#Uni-Dsn 1
#StdAll BC
#DWRATIO 3.170
#MINTHK 0 0
#Max_Kw 180.000
#Max_Kb 33.170
#Max_Uc 0.900
#Max_LR 0

*END
END COLUMN -OUTPUT
** Front Page [DET] .....

ZAMIL STEEL INDUSTRIES


P.O.Box 877
Dammam 31421
Kingdom of Saudi Arabia

A S F A D
Advanced Steel Frame Analysis & Design
Version No. 1911.169 Nov 2019
Founded(1995) by: K.R.Ezzat
Developed by: Engineering Systems Dept.
DESIGN SHEET Page 65 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

File Name : C:\Users\sv4012\Desktop\N2-6284\ASFAD\EW COLUMN.out


Run By : PLT
Date : 24-12-2019 at 10:04
Design Code : [AISC-89]

Units : Metric
Modulus of Elasticity : 19995.00 kN/cm2
Coefficient of Expansion : 0.0000117

Concrete Bearing Stress : -1.00 kN/cm2


Steel Density : 7850.00 Kg/m3
Segment Size : 0.60 m

Page Size : 66

...........................................................................................

Detail Input Report


Page Number.. 1
N2-6284-B01-A01-R00 *** ENDWALL COLUMN : GL. 13 10:04 24-12-2019
----------------------------------------------------------------------------------------

*HEADER
VERSION: 1604143
TITLE: N2-6284-B01-A01-R00 *** ENDWALL COLUMN : GL. 13
INIT: PLT
CONST: PAGE=66 FY=34.50 FB=1.00 PP=0 SEGMENT=0.60 BOLT=A325-36SV MOMENT=0.50 FBRAC=0
CONST: MINABOLT=0-4 MINBOLT=1-5
OUTPUT: I R D C -FC -FM -FP T -M U E4

*NODES
3 4.000 1.000
4 4.000 4.100
5 8.000 1.000
6 8.000 4.959

*SUPPORTSDF
3 X Y
4 X
5 X Y
6 X

*MEMBERS
3 4 0.00 0.00 NNN NNN
200.00 200.00 125.00X05.00 4.00 125.00X05.00 0.00 I
BRACING 1.7D 3.4T 5.10D 6.80T
5 6 0.00 0.00 NNN NNN
200.00 200.00 125.00X05.00 4.00 125.00X05.00 0.00 I
BRACING 1.7D 3.4T 5.10D 6.80T

*LOADS
3 4 DEAD GWY -1.00 0.00 -1.00
5 6 DEAD GWY -1.00 0.00 -1.00
G ALL
//EC1
/WIND PRESSURE Q = 0.48 KN/M2 ; TRI = 3M , CP=0.9
DESIGN SHEET Page 66 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


///
3 4 WINDP GUX 1.166 0.00 -1.00
3 4 WINDS GUX -1.296 0.00 -1.00
/TRI =6M
5 6 WINDP GUX 2.333 0.00 -1.00
5 6 WINDS GUX -2.592 0.00 -1.00
/EWR
//
4 3 DEAD GCY -1,695 0,00
4 3 COLL GCY -0,608 0,00
4 3 LIVE GCY -6,929 0,00
4 3 WINDP GCY -2,147 0,00
4 3 WINDP GCX 0,490 0,00
4 3 WINDS GCY -7,305 0,00
4 3 WINDS GCX 1,666 0,00
//
//
6 5 DEAD GCY -1,695 0,00
6 5 COLL GCY -0,608 0,00
6 5 LIVE GCY -6,929 0,00
6 5 WINDP GCY -2,147 0,00
6 5 WINDP GCX 0,490 0,00
6 5 WINDS GCY -7,305 0,00
6 5 WINDS GCX 1,666 0,00
//
STATIC 4 DEAD

...........................................................................................

Detail Input Report


Page Number.. 2
N2-6284-B01-A01-R00 *** ENDWALL COLUMN : GL. 13 10:04 24-12-2019
----------------------------------------------------------------------------------------

*LOADCOND
@RDS 1.00 0.60 DEAD + 1.00 WIND

*DESIGN
1 2 KX=1.00 OFF-KX=0.00 KY=1.00 FY=34.50 CB=0.00 CM=-1.00 A/H=5.00 LY-EXT=0

*CONNECTIONS
P 3 4 BR420-12
P 5 6 BR420-12

*GEOM
#UNI-DSN 1
#STDALL BC
#DWRATIO 3.170
#MINTHK 0 0
#MAX_KW 180.000
#MAX_KB 33.170
#MAX_UC 0.900
#MAX_LR 0

*END
.
.** Errors Log **
.
DESIGN SHEET Page 67 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


.
.** Processed with No Errors **

...........................................................................................

Input Details Report


Page Number.. 1
N2-6284-B01-A01-R00 *** ENDWALL COLUMN : GL. 13 10:04 24-12-2019
----------------------------------------------------------------------------------------

Coordinates Restraints Elastic Restraint Coeff.


Node X Y X Y M X Y M
No. (.....meters....) (Y=Rest. E=Elas.) kN/m kN/m kN.m/deg
---- ----------------- ----------------- ------------------------------

3 4.000 1.000 Y Y
4 4.000 4.100 Y
5 8.000 1.000 Y Y
6 8.000 4.959 Y

Offsets Releases
Member No of Start End Start End
No. Start End Sections (.....m.....) X Y M X Y M
------------- -------- ------------- ------------

1 3 - 4 1 0.00 0.00
2 5 - 6 1 0.00 0.00

Web Depth Top Flange Web Bottom Flange


Section Length (....mm....) Section (.....mm.....) thick (.....mm.....)
Member No. (m) Start End type width x thick (mm) width x thick
--------- ---- ------- --------------- ------- ---------------- ------ ----------------

3 - 4 1 3.100 200.00 200.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00

5 - 6 1 3.959 200.00 200.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00

Member Bracings (distance ..meters , T:Top Flg - B:Bottom Flg - D:Double both Flgs)
--------- ------------------------------------------------------------------------------

3 - 4 1.55N 1.70D 3.10N

5 - 6 1.70D 1.98N 3.40T 3.96N

...........................................................................................

Input Details Report


Page Number.. 2
N2-6284-B01-A01-R00 *** ENDWALL COLUMN : GL. 13 10:04 24-12-2019
----------------------------------------------------------------------------------------

Load Load Value Start/End Start & End Distances Angle


No. Member Type ( kN kN/m kN.m ) (..m.. '-' ratio of length) (Deg)
DESIGN SHEET Page 68 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


--- --------- ---- ---------------------- -----------------------------------

Load Case No. 1 DEAD

1 3 - 4 GWY -1.00 x Own WT from 0.00 to -1.00


2 5 - 6 GWY -1.00 x Own WT from 0.00 to -1.00
3 3 - 4 GWY -1.00 x Own WT from 0.00 to -1.00
4 4 - 3 GCY -1.00 at 0.00
5 6 - 5 GCY -1.00 at 0.00

Load Case No. 2 COLL

1 4 - 3 GCY -0.00 at 0.00


2 6 - 5 GCY -0.00 at 0.00

Load Case No. 3 LIVE

1 4 - 3 GCY -6.00 at 0.00


2 6 - 5 GCY -6.00 at 0.00

Load Case No. 4 WINDP

1 3 - 4 GUX 1.17 from 0.00 to -1.00


2 5 - 6 GUX 2.33 from 0.00 to -1.00
3 4 - 3 GCY -2.00 at 0.00
4 4 - 3 GCX 0.00 at 0.00
5 6 - 5 GCY -2.00 at 0.00
6 6 - 5 GCX 0.00 at 0.00

Load Case No. 5 WINDS

1 3 - 4 GUX -1.30 from 0.00 to -1.00


2 5 - 6 GUX -2.59 from 0.00 to -1.00
3 4 - 3 GCY -7.00 at 0.00
4 4 - 3 GCX 1.00 at 0.00
5 6 - 5 GCY -7.00 at 0.00
6 6 - 5 GCX 1.00 at 0.00

Static Load Cases :

1. Load Case No. 1 DEAD

Load Category No. 1 [Indiv.] COLL

1. Load Case No. 2 COLL

Load Category No. 2 [Indiv.] LIVE

1. Load Case No. 3 LIVE

...........................................................................................

Input Details Report


Page Number.. 3
N2-6284-B01-A01-R00 *** ENDWALL COLUMN : GL. 13 10:04 24-12-2019
DESIGN SHEET Page 69 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


----------------------------------------------------------------------------------------

Load Category No. 3 [Indiv.] WIND

1. Load Case No. 4 WINDP


2. Load Case No. 5 WINDS

Load Condition No. 1 @ RSD With 1.00 Stress Factor


1. 0.60 x DEAD
2. 1.00 x WIND

...........................................................................................

Reactions & Displacements Report


Page Number.. 4
N2-6284-B01-A01-R00 *** ENDWALL COLUMN : GL. 13 10:04 24-12-2019
----------------------------------------------------------------------------------------

Structure Reactions and Displacements - Load Case no. 1...DEAD

Vertical Horizontal Moment Vertical Horizontal Rotation


Node Reaction Reaction Reaction Displac. Displac. Angle
No. (kN) (kN) (kN.m) (cm) (cm) (deg)
---- ---------- ---------- ---------- ---------- ---------- ----------
3 1.978 -0.000 -0.000 0.000 0.000 -0.000
4 -0.000 -0.000 0.000 -0.001 0.000 0.000
5 1.625 -0.000 -0.000 0.000 0.000 -0.000
6 -0.000 -0.000 0.000 -0.001 0.000 0.000

Structure Reactions and Displacements - Load Case no. 2...COLL

Vertical Horizontal Moment Vertical Horizontal Rotation


Node Reaction Reaction Reaction Displac. Displac. Angle
No. (kN) (kN) (kN.m) (cm) (cm) (deg)
---- ---------- ---------- ---------- ---------- ---------- ----------
3 -0.000 -0.000 -0.000 0.000 0.000 0.000
4 -0.000 -0.000 -0.000 0.000 0.000 0.000
5 -0.000 -0.000 -0.000 0.000 0.000 0.000
6 -0.000 -0.000 -0.000 0.000 0.000 0.000

Structure Reactions and Displacements - Load Case no. 3...LIVE

Vertical Horizontal Moment Vertical Horizontal Rotation


Node Reaction Reaction Reaction Displac. Displac. Angle
No. (kN) (kN) (kN.m) (cm) (cm) (deg)
---- ---------- ---------- ---------- ---------- ---------- ----------
3 6.000 -0.000 -0.000 0.000 0.000 0.000
4 -0.000 -0.000 -0.000 -0.005 0.000 0.000
5 6.000 -0.000 -0.000 0.000 0.000 0.000
6 -0.000 -0.000 -0.000 -0.006 0.000 0.000

Structure Reactions and Displacements - Load Case no. 4...WINDP

Vertical Horizontal Moment Vertical Horizontal Rotation


Node Reaction Reaction Reaction Displac. Displac. Angle
DESIGN SHEET Page 70 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


No. (kN) (kN) (kN.m) (cm) (cm) (deg)
---- ---------- ---------- ---------- ---------- ---------- ----------
3 2.000 -1.807 -0.000 0.000 0.000 -0.026
4 -0.000 -1.807 -0.000 -0.002 0.000 0.026
5 2.000 -4.618 -0.000 0.000 0.000 -0.109
6 -0.000 -4.618 -0.000 -0.002 0.000 0.109

Structure Reactions and Displacements - Load Case no. 5...WINDS

Vertical Horizontal Moment Vertical Horizontal Rotation


Node Reaction Reaction Reaction Displac. Displac. Angle
No. (kN) (kN) (kN.m) (cm) (cm) (deg)
---- ---------- ---------- ---------- ---------- ---------- ----------
3 7.000 2.009 -0.000 0.000 0.000 0.029
4 -0.000 1.009 0.000 -0.005 0.000 -0.029
5 7.000 5.131 -0.000 0.000 0.000 0.121
6 -0.000 4.131 0.000 -0.007 0.000 -0.122

...........................................................................................

Reactions & Displacements Report


Page Number.. 5
N2-6284-B01-A01-R00 *** ENDWALL COLUMN : GL. 13 10:04 24-12-2019
----------------------------------------------------------------------------------------

Structure Max Positive Reactions Structure Max Negative Reactions

Vertical Horizontal Moment Vertical Horizontal Moment


Node Reac. Load Reaction Reaction Reaction Load Reaction Reaction Reaction
No. Type Cond (kN) (kN) (kN.m) Cond (kN) (kN) (kN.m)
---- ---- ---- ---------- ---------- ---------- ---- ---------- ---------- ----------

3 H 1 8.187 2.009 -0.000 1 3.187 -1.807 -0.000


3 V 1 8.187 2.009 -0.000 0 -0.000 -0.000 -0.000

4 H 1 -0.000 1.009 0.000 1 -0.000 -1.807 0.000

5 H 1 7.975 5.131 -0.000 1 2.975 -4.618 -0.000


5 V 1 7.975 5.131 -0.000 0 -0.000 -0.000 -0.000

6 H 1 -0.000 4.131 0.000 1 -0.000 -4.618 -0.000

...........................................................................................

Design Summary Report based on AISC-89


Page Number.. 6
N2-6284-B01-A01-R00 *** ENDWALL COLUMN : GL. 13 10:04 24-12-2019
----------------------------------------------------------------------------------------

****************************************************************************************
Member 3 - 4 Length = 3.100 meters Fy = 34.50 kN/cm2 Weight = 49.887 Kg
****************************************************************************************

Web Depth Top Flange Web Bottom Flange


Section Length (....mm....) Section (.....mm.....) thick (.....mm.....) Unity
No. (m) Start End type width x thick (mm) width x thick Check
DESIGN SHEET Page 71 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


---- ------- --------------- ------- ---------------- ------ ---------------- -----
1 3.100 200.00 200.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00 Pass

Maximum Forces Allowable Stresses Calculated Stresses


Section Moment Axial @ Dist Load (......kN/cm2.....) (......kN/cm2.....) Stress
No. (kN.m) (kN) (m) cond Fa Fb-Top Fb-Bott fa fb-Top fb-Bott Ratio
---- ---------------------------- --------------------- --------------------- -------
1 -1.56 -7.89 1.55 1 14.55 20.70 19.96 -0.39 1.03 -1.03 0.08

Section Maximum Allow. Calcu. Max + Deflection Max - Deflection


No. Shear @ Dist Load Fv fv Stress Def. @ Dist Load Def. @ Dist Load
(kN) (m) cond (...kN/cm2..) Ratio (cm) (m) cond (cm) (m) cond
---- -------------------- ------ ------ ------ ------------------ ------------------
1 2.01 0.00 1 13.80 0.25 0.02 0.05 1.55 1 -0.04 1.55 1

****************************************************************************************
Member 5 - 6 Length = 3.959 meters Fy = 34.50 kN/cm2 Weight = 63.710 Kg
****************************************************************************************

Web Depth Top Flange Web Bottom Flange


Section Length (....mm....) Section (.....mm.....) thick (.....mm.....) Unity
No. (m) Start End type width x thick (mm) width x thick Check
---- ------- --------------- ------- ---------------- ------ ---------------- -----
1 3.959 200.00 200.00 I-00 125.00 x 5.00 4.00 125.00 x 5.00 Pass

Maximum Forces Allowable Stresses Calculated Stresses


Section Moment Axial @ Dist Load (......kN/cm2.....) (......kN/cm2.....) Stress
No. (kN.m) (kN) (m) cond Fa Fb-Top Fb-Bott fa fb-Top fb-Bott Ratio
---- ---------------------------- --------------------- --------------------- -------
1 -5.08 -7.79 1.98 1 12.39 20.70 17.64 -0.38 3.37 -3.37 0.22

Section Maximum Allow. Calcu. Max + Deflection Max - Deflection


No. Shear @ Dist Load Fv fv Stress Def. @ Dist Load Def. @ Dist Load
(kN) (m) cond (...kN/cm2..) Ratio (cm) (m) cond (cm) (m) cond
---- -------------------- ------ ------ ------ ------------------ ------------------
1 5.13 0.00 1 13.80 0.64 0.05 0.26 1.98 1 -0.24 1.98 1
----------------------------------------------------------------------------------------
Frame Weight = 113.6 Kg Surface Area = 6.6 m2 ( 53.8 m2/Ton)
Conn. Weight = 8.7 Kg

...........................................................................................

Unity Check AISC-89 & Deflection Summary Report


Page Number.. 7
N2-6284-B01-A01-R00 *** ENDWALL COLUMN : GL. 13 10:04 24-12-2019
----------------------------------------------------------------------------------------

Section Length Shear AX+BM Max + Def Max - Def Check


No. (m) Cond Uc Cond Uc Cond (cm) Cond (cm)
-----------------------------------------------------------------------------------
Member 3 - 4 1 3.100 | 1 0.02 1 0.08 | 1 0.05 1 -0.04 | Pass
-----------------------------------------------------------------------------------
Member 5 - 6 1 3.959 | 1 0.05 1 0.22 | 1 0.26 1 -0.24 | Pass
-----------------------------------------------------------------------------------

...........................................................................................

Connections Summary Report based on AISC-89


DESIGN SHEET Page 72 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Page Number.. 8
N2-6284-B01-A01-R00 *** ENDWALL COLUMN : GL. 13 10:04 24-12-2019
----------------------------------------------------------------------------------------

********************************************************************************
Connection Type : Pinned Base at Joint 3 Member 3 - 4
********************************************************************************

Section dimensions :
Web Top/Outer Flange Bot/inner Flange
(.....mm......) (.....mm......) (.....mm......)
--------------- ---------------- ----------------
sec @ Connection 200.00 x 4.00 125.00 x 5.00 125.00 x 5.00

Controlling Forces :
Moment Vert. Load Horiz.
kN.m kN Cond kN
-------- -------- ---- -------
0.00 0.00 0 2.01
0.00 -8.19 1 2.01

Connection Design :

Bolts conforming to ASTM F-1554 Gr 36 - SV25UD

Anchor bolts 2 Rows (all inside) x 2 = 4 size 20.00 mm

Base plate size 200 x 210 x 12 mm Fy = 34.50 kN/cm2

Actual Allowable
kN kN Ratio
--------- --------- -----
Anchor Bolt Tension 0.00 41.47 0.00
Bearing stress /cm2 0.02 0.63 0.03
Base Plate Moment 0.12 6.21 0.02
Average Bolt Shear 0.50 21.36 0.02

Standard Connection Code ## BR420-12 ##

--------------------------------------------------------------------------------

...........................................................................................

Connections Summary Report based on AISC-89


Page Number.. 9
N2-6284-B01-A01-R00 *** ENDWALL COLUMN : GL. 13 10:04 24-12-2019
----------------------------------------------------------------------------------------

********************************************************************************
Connection Type : Pinned Base at Joint 5 Member 5 - 6
********************************************************************************

Section dimensions :
Web Top/Outer Flange Bot/inner Flange
(.....mm......) (.....mm......) (.....mm......)
--------------- ---------------- ----------------
DESIGN SHEET Page 73 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


sec @ Connection 200.00 x 4.00 125.00 x 5.00 125.00 x 5.00

Controlling Forces :
Moment Vert. Load Horiz.
kN.m kN Cond kN
-------- -------- ---- -------
0.00 0.00 0 5.13
0.00 -7.97 1 5.13

Connection Design :

Bolts conforming to ASTM F-1554 Gr 36 - SV25UD

Anchor bolts 2 Rows (all inside) x 2 = 4 size 20.00 mm

Base plate size 200 x 210 x 12 mm Fy = 34.50 kN/cm2

Actual Allowable
kN kN Ratio
--------- --------- -----
Anchor Bolt Tension 0.00 41.47 0.00
Bearing stress /cm2 0.02 0.63 0.03
Base Plate Moment 0.12 6.21 0.02
Average Bolt Shear 1.28 21.36 0.06

Standard Connection Code ## BR420-12 ##

--------------------------------------------------------------------------------
DESIGN SHEET Page 74 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


DESIGN SHEET Page 75 of
Job No. Building No. Rev. No. 00

Customer Logistics SolutionTables


Design Reference Provider
and Data Sheets Date

Description Designed ByChecked By

Section 3 : Design Reference Tables and Computer Explanation

 Type “S” Panel Properties and Load Table


 Z Shape Purlin Properties and Design Table
 Z Shape Girt Properties and Design Table
 End Wall Girt Design Table
 Z Shape Purlin and Girt lap details
 [ Shape Properties
 Eave Strut Properties
 Eave Strut Capacity Table
 How ASFAD Works
 Rigid Frame Connection Details
DESIGN SHEET Page 76 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

TYPE “S” PANEL

Note: D + L = Dead + Live Load (Deflection limit Span/180)

Panel Top in Compression Bottom in Compression Web Shear & Cripp.


Thickness Weight Area Ix Zx-Top Zx-Bott. Ma Ix Zx-Top Zx-Bott. Ma Va Pa
mm kg/m2 cm2 cm4 cm3 cm3 kN.m cm4 cm3 cm3 kN.m kN kN
0.50 4.78 6.09 5.76 1.93 7.38 0.40 5.52 2.47 3.89 0.51 4.97 3.39
0.60 5.74 7.31 8.07 2.67 9.46 0.55 7.33 3.15 5.34 0.65 9.71 5.43
0.70 6.70 8.54 10.16 3.62 11.35 0.75 9.20 3.84 7.00 0.79 15.83 7.76

Panel Number
Thickness of Load Span in meters
mm Spans Case 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00 3.50
D+L 3.20 2.05 1.42 0.95 0.63 0.44 0.32 0.24 0.19 0.12
1 WP 4.26 2.72 1.89 1.39 0.95 0.67 0.49 0.37 0.28 0.18
WS 5.43 3.47 2.16 1.36 0.91 0.64 0.47 0.35 0.27 0.17
D+L 2.71 2.17 1.81 1.33 1.02 0.81 0.65 0.54 0.45 0.28
0.50 2 WP 3.59 2.87 2.40 1.77 1.36 1.07 0.87 0.72 0.60 0.43
WS 4.26 2.72 1.89 1.39 1.06 0.84 0.68 0.56 0.47 0.35
D+L 3.08 2.47 2.06 1.67 1.20 0.84 0.61 0.46 0.35 0.22
3 WP 4.10 3.28 2.73 2.22 1.70 1.26 0.92 0.69 0.53 0.33
WS 5.33 3.41 2.37 1.74 1.33 1.05 0.85 0.66 0.51 0.32
D+L 4.40 2.82 1.96 1.33 0.89 0.62 0.45 0.34 0.26 0.17
1 WP 5.85 3.75 2.60 1.91 1.33 0.94 0.68 0.51 0.39 0.25
WS 6.92 4.43 2.87 1.81 1.21 0.85 0.62 0.47 0.36 0.23
D+L 4.34 3.33 2.31 1.70 1.30 1.03 0.83 0.69 0.58 0.40
0.60 2 WP 5.76 4.43 3.07 2.26 1.73 1.37 1.11 0.91 0.77 0.56
WS 5.85 3.75 2.60 1.91 1.46 1.16 0.94 0.77 0.65 0.48
D+L 4.94 3.95 2.89 2.12 1.63 1.18 0.86 0.64 0.50 0.31
3 WP 6.57 5.26 3.85 2.83 2.17 1.71 1.29 0.97 0.74 0.47
WS 7.33 4.69 3.26 2.39 1.83 1.45 1.17 0.88 0.68 0.43
D+L 6.00 3.84 2.65 1.67 1.12 0.78 0.57 0.43 0.33 0.21
1 WP 7.98 5.11 3.55 2.50 1.68 1.18 0.86 0.64 0.50 0.31
WS 8.41 5.38 3.60 2.27 1.52 1.07 0.78 0.58 0.45 0.28
D+L 6.21 4.04 2.81 2.06 1.58 1.25 1.01 0.84 0.70 0.50
0.70 2 WP 8.23 5.38 3.74 2.74 2.10 1.66 1.34 1.11 0.93 0.69
WS 7.98 5.11 3.55 2.61 2.00 1.58 1.28 1.06 0.89 0.65
D+L 7.06 5.06 3.51 2.58 1.98 1.48 1.08 0.81 0.62 0.39
3 WP 9.39 6.74 4.68 3.44 2.63 2.08 1.62 1.22 0.94 0.59
WS 10.00 6.40 4.44 3.26 2.50 1.97 1.47 1.10 0.85 0.53

WP = Wind Pressure (Deflection limit Span/120)


WS = Wind Pressure (Deflection limit Span/120)
Material conforming to ASTM A792 Grade 50B (F y = 34.5 kN/cm2 ) or equivalent
DESIGN SHEET Page 77 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

Z Shape Purlin Properties and Design Table

SECTION PROPERTIES
ABOUT X-X AXIS ABOUT Y-Y AXIS
SECTION WEIGHT THICK AREA EFF I = Ix Gross Eff. Rx Iy Iyc Sy Ry
KG/M mm cm2 AREA H/t Defl. Sxc = Sx Sxc
cm2 cm4 cm3 cm3 cm cm4 cm4 cm3 cm
200Z15 4.06 1.50 5.18 4.90 123.33 308.3 30.83 26.28 7.72 42.49 21.25 5.98 2.87
200Z17 4.74 1.75 6.04 5.77 105.43 358.8 35.88 31.50 7.71 49.86 24.93 7.01 2.87
200Z20 5.42 2.00 6.90 6.74 92.00 409.1 40.91 38.49 7.70 57.30 28.65 8.05 2.88
200Z22 6.09 2.25 7.76 7.66 81.56 459.1 45.91 44.41 7.69 64.83 32.41 9.10 2.89
200Z25 6.77 2.50 8.62 8.62 73.20 509.0 50.90 50.90 7.68 72.43 36.22 10.16 2.90
200Z30 8.12 3.00 10.35 10.35 60.67 607.9 60.79 60.79 7.66 87.88 43.94 12.32 2.91
NOTE: For The Properties Of Nested Purlins Add The Appropriate Individual Section Properties Except H/t , R x And Ry.

PURLIN DESIGN TABLE


BAY WIND SPEED 110 130 150
SPACING (KMPH)
(M) LIVE LOAD 0.57 1.0 0.57 1.0 0.57 1.0
(KN/M2)
END BAY Z15 SHORT Z15 CONT Z15 CONT Z15 CONT Z17 CONT Z17 CONT
6.0 SECOND BAY Z15 SHORT Z15 CONT Z15 CONT Z15 CONT Z15 CONT Z15 CONT
INTERIOR BAY Z15 SHORT Z15 CONT Z15 CONT Z15 CONT Z15 CONT Z15 CONT
END BAY Z15 SHORT Z17 CONT Z17 CONT Z17 CONT Z20 CONT Z20 CONT
6.5 SECOND BAY Z15 SHORT Z17 CONT Z15 CONT Z17 CONT Z15 CONT Z17 CONT
INTERIOR BAY Z15 SHORT Z15 CONT Z15 CONT Z15 CONT Z15 CONT Z15 CONT
END BAY Z15 CONT Z20 CONT Z17 CONT Z20 CONT Z22 CONT Z22 CONT
7.0 SECOND BAY Z15 CONT Z20 CONT Z15 CONT Z20 CONT Z17 CONT Z20 CONT
INTERIOR BAY Z15 CONT Z17 CONT Z15 CONT Z17 CONT Z15 CONT Z17 CONT
END BAY Z15 CONT Z20 CONT Z20 CONT Z20 CONT Z25 CONT Z25 CONT
7.5 SECOND BAY Z15 CONT Z20 CONT Z15 CONT Z20 CONT Z20 CONT Z20 CONT
INTERIOR BAY Z15 CONT Z17 CONT Z15 CONT Z17 CONT Z15 CONT Z17 CONT
END BAY Z17 CONT Z22 CONT Z22 CONT Z22 CONT Z30 CONT Z30 CONT
8.0 SECOND BAY Z17 CONT Z22 CONT Z17 CONT Z22 CONT Z20 CONT Z22 CONT
INTERIOR BAY Z15 CONT Z20 CONT Z15 CONT Z20 CONT Z17 CONT Z20 CONT
END BAY Z17 CONT Z25 CONT Z25 CONT Z25 CONT Z40 CONT Z40 CONT
8.5 SECOND BAY Z17 CONT Z25 CONT Z17 CONT Z25 CONT Z22 CONT Z25 CONT
INTERIOR BAY Z15 CONT Z20 CONT Z15 CONT Z20CONT Z17CONT Z20 CONT
END BAY Z20 CONT Z30 LONG Z30 CONT Z30 LONG Z40 CONT Z40 LONG
9.0 SECOND BAY Z20 CONT Z22 LONG Z20 CONT Z22 LONG Z25 CONT Z22 LONG
INTERIOR BAY Z17 CONT Z20 LONG Z17 CONT Z20 LONG Z20 CONT Z20 LONG

NOTES: The following are the points, that have been considered for the above table.
1) 8 continuous bays 4) Refer standard lap lengths for short, continuous and long laps.
2) Dead load, DL = 0.10KN/M2 (INC. SELF WEIGHT) 5) Eave Height = 9m
3) Purlin Spacing = 1.5 M . 6) The maximum possible load combinations considered are: DL+LL; DL+WL
DESIGN SHEET Page 78 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


Z Shape Girt Properties and Design Table

SECTION PROPERTIES
ABOUT X-X AXIS ABOUT Y-Y AXIS
SECTION WEIGHT THICK AREA EFF I = Ix Gross Eff. Rx Iy Iyc Sy Ry
KG/M mm cm2 AREA H/t Defl. Sxc = Sx Sxc
cm2 cm4 cm3 cm3 cm cm4 cm4 cm3 cm
200Z15 4.06 1.50 5.18 4.90 123.33 308.3 30.83 26.28 7.72 42.49 21.25 5.98 2.87
200Z17 4.74 1.75 6.04 5.77 105.43 358.8 35.88 31.50 7.71 49.86 24.93 7.01 2.87
200Z20 5.42 2.00 6.90 6.74 92.00 409.1 40.91 38.49 7.70 57.30 28.65 8.05 2.88
200Z22 6.09 2.25 7.76 7.66 81.56 459.1 45.91 44.41 7.69 64.83 32.41 9.10 2.89
200Z25 6.77 2.50 8.62 8.62 73.20 509.0 50.90 50.90 7.68 72.43 36.22 10.16 2.90
200Z30 8.12 3.00 10.35 10.35 60.67 607.9 60.79 60.79 7.66 87.88 43.94 12.32 2.91
NOTE: For The Properties Of Nested Purlins Add The Appropriate Individual Section Properties Except H/t , R x And Ry.

SideWall Girts Design Table


BAY WIND SPEED in 110 120 130 140 150 160
SPACING KPH (0.56) (0.66) (0.78) (0.90) (1.04) (1.18)
(M) (q in kN/m2)
END BAY Z15 SHORT Z15 CONT Z15 CONT Z17 CONT Z20 CONT Z20 CONT
6.0 SECOND BAY Z15 SHORT Z15 CONT Z15 CONT Z15 CONT Z15 CONT Z17 CONT
INTERIOR BAY Z15 SHORT Z15 CONT Z15 CONT Z15 CONT Z15 CONT Z15 CONT
END BAY Z15 CONT Z15 CONT Z17 CONT Z20 CONT Z20 CONT Z22 CONT
6.5 SECOND BAY Z15 CONT Z15 CONT Z15 CONT Z15 CONT Z17 CONT Z17 CONT
INTERIOR BAY Z15 CONT Z15 CONT Z15 CONT Z15 CONT Z15 CONT Z15 CONT
END BAY Z15 CONT Z17 CONT Z20 CONT Z20 CONT Z22 CONT Z25 CONT
7.0 SECOND BAY Z15 CONT Z15 CONT Z15 CONT Z17 CONT Z20 CONT Z20 CONT
INTERIOR BAY Z15 CONT Z15 CONT Z15 CONT Z15 CONT Z15 CONT Z17 CONT
END BAY Z17 CONT Z20 CONT Z20 CONT Z22 CONT Z25 CONT Z30 CONT
7.5 SECOND BAY Z15 CONT Z15 CONT Z17 CONT Z17 CONT Z20 CONT Z22 CONT
INTERIOR BAY Z15 CONT Z15 CONT Z15 CONT Z15 CONT Z17 CONT Z20 CONT
END BAY Z17 CONT Z20 CONT Z22 CONT Z25 CONT Z30 CONT Z40 CONT
8.0 SECOND BAY Z15 CONT Z17 CONT Z17 CONT Z20 CONT Z22 CONT Z25 CONT
INTERIOR BAY Z15 CONT Z15 CONT Z15 CONT Z17 CONT Z20 CONT Z20 CONT
END BAY Z20 CONT Z22 CONT Z25 CONT Z30 CONT Z40 CONT Z40 LONG
8.5 SECOND BAY Z15 CONT Z17 CONT Z20 CONT Z22 CONT Z25 CONT Z22 LONG
INTERIOR Z15 CONT Z15 CONT Z17 CONT Z20 CONT Z20 CONT Z22 LONG
END BAY Z22 CONT Z25 CONT Z30 CONT Z40 CONT Z40 LONG Z45 LONG
9.0 SECOND BAY Z17 CONT Z20 CONT Z22 CONT Z25 CONT Z22 LONG Z25 LONG
INTERIOR BAY Z15 CONT Z17 CONT Z20 CONT Z20 CONT Z22 LONG Z25 LONG

NOTES: The following points have been considered for the above table.
1) 8 continuous bays. 6) Eave Height = 9m
2) Tributary Width = 1.9m 7) Deflection Limit = Span / 120
3) Standard laps: Short, Continuous and Long laps (Refer to the standard Lap dimensions)
4) Wind Pressure and Suction both have been considered.
5) MBMA GCp Coefficients for fully enclosed building condition.
DESIGN SHEET Page 79 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

End Wall Girts Design Table

GIRT SPAN WIND SPEED in KPH


(M) (q in kN/m2)
110 120 130 140 150 160
(0.56) (0.66) (0.78) (0.90) (1.04) (1.18)
3.0 Z15 Z15 Z15 Z15 Z15 Z15
3.5 Z15 Z15 Z15 Z15 Z15 Z17
4.0 Z15 Z15 Z15 Z17 Z20 Z20
4.5 Z15 Z15 Z17 Z20 Z22 Z25
5.0 Z17 Z20 Z20 Z22 Z25 Z30
5.5 Z20 Z20 Z25 Z30 Z30 Z40
6.0 Z22 Z25 Z30 Z35 Z40 Z45
6.5 Z25 Z30 Z40 Z40 Z45 Z50
7.0 Z30 Z35 Z40 Z45 Z50
7.5 Z30 Z40 Z45 Z50
8.0 Z40 Z45 Z50
8.5 Z45 Z50
9.0 Z45

NOTES: The following points have been considered for the above table.
1) Designed for Simple Span 5) Eave Height = 9m
2) Tributary Width = 1.9m 6) Wind Pressure and Suction both have been considered
3) Deflection Limit = Span /120
4) MBMA GCp Coefficients used for fully enclosed building condition.
DESIGN SHEET Page 80 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


.

LAP DETAILS

SHORT LAP
(FOR LIGHT LOADING SHORT SPAN)

INTERMEDIATE LAP/CONTINUOUS LAP LONG LAP


(FOR MEDIUM LOAD & INTERMEDIATE SPANS) (FOR HIGH LOADING AND LONG SPANS)
(TYPICAL MULTIPLE SPANS) (MULTIPLE SPAN)

NOTE: ALL DIMENSIONS ARE IN MILLIMETER.

'C' SHAPE SECTION PROPERTIES


DESIGN SHEET Page 81 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

Notes:
1. Dimensions are out to out of section thickness, t.
2. All sections are designed in accordance with the Cold-
Formed Steel Design Manual, AISI 1986 Edition
3. Specific yield strength “Fy” of light gauge cold-
formed steel = 34.50 kN/cm2
4. C.G. = Center of Gravity
5. S.C. = Shear Center
6. Coil width = 390 mm

Section Properties

About X-X Axis About Y-Y Axis Others


Gross Defl. Gross Eff. Rx Iy Iyc Min. Max. Ry Xcg Xcm
Section Ix Ix Sx Sx (c Sy Sy
(cm4) (cm4) (cm3) (cm4) (cm) (cm4) m4) (cm3) (cm3) (cm ) (cm ) (cm )
200C20 491.7 481.8 49.17 41.45 7.86 73.37 36.69 12.12 29.98 3.07 2.447 3.989
200C25 610.6 609.9 61.06 53.71 7.91 91.76 45.88 15.19 37.32 3.07 2.459 4.016

General Data Allowable Allowable Bending


Shear Moment
Section Force (kN.m)
Weight Thick L Gross Effect Area
(kg/m) (mm) (mm) Area (cm2) (cm2) H/t (kN) Ma Ma2*
200C20 6.11 2.0 20.0 7.80 7.28 92.0 25.03 8.56 4.55
200C25 7.64 2.5 21.2 9.75 9.23 73.2 45.98 11.10 5.91

* Based on a reduction factor of 0.40 for simple spans with one unbraced compression side and an increase of 33% on allowable stress for wind load
application.

'C' SHAPE SECTION PROPERTIES


Notes:
DESIGN SHEET Page 82 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

1. Dimensions are out to out of section thickness, t.


2. All sections are designed in accordance with the Cold-
Formed Steel Design Manual, AISI 1986 Edition.
3. Specific yield strength “Fy” of light gauge cold-formed
steel = 34.50 kN/cm2
4. C.G. = Center of Gravity
5. S.C. = Shear Center
6. Coil width = 495 mm

Section Properties

About X-X Axis About Y-Y Axis Others


Gross Ix Defl. Gross Sx Eff. Rx Iy Iyc Min. Max. Ry Xcg Xcm
Section (cm4) Ix (cm3) Sx (cm Sy Sy
(cm4) (cm3) (cm) (cm4) 4
) (cm3) (cm3) (cm ) (cm ) (cm )
300 x 85 x 2.0 x 25 1308.5 1308.5 87.23 74.29 11.50 91.81 45.91 14.55 41.90 3.04 2.19 3.61

General Data Allowable Allowable Bending


Shear Force Moment (kN.m)
Section
Weight Thick L Gross Effect
Area Area H/t (kN) Ma Ma2*
(kg/m) (mm) (mm) (cm2) (cm2)
300 x 85 x 2.0 x 25 7.78 2.0 25.65 9.90 9.14 142.0 15.94 15.34 8.18

* Based on a reduction factor of 0.40 for simple spans with one unbraced compression side and an increase of 33% on allowable stress for wind load
application.
DESIGN SHEET Page 83 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

EAVE STRUT SECTION PROPERTIES

NOTES :

1. Calculation dimensions are out to out of Section


thickness, t.

2. All sections are designed with reference to the


Specifications of “Cold-Formed Steel Design Manual”
AISI 1986 Edition.

3. Specific yield strength of light gauge Cold-Formed steel


Fy = 34.50 kN/cm2.

4. CG = Center of Gravity.

6. SC = Shear Center

7. Coil width = 390 mm

GENERAL DATA ALLOWABLE BENDING


ALLOW. NOMINA MOMENT KN-M
L
SECTIO WEIGHT THICK L GROSS EFF H/t SHEAR MOMENT Mag Mawc* Maws+
N KG/M mm mm AREA AREA FORCE STRENG
cm2 cm2 KN TH
KN-M
180ES20 5.88 2.0 22.50 7.50 7.00 82.00 28.09 12.78 7.65 6.11 4.07
180ES25 7.35 2.5 26.70 9.38 8.93 62.20 45.98 16.72 10.01 8.00 5.33

Legend: g = gravity w = wind c = continuous s = simple span

SECTION PROPERTIES
ABOUT X-X AXIS ABOUT Y-Y AXIS OTHERS
SECTION Gross Defl. Gross Eff. Rx Iy Iyc Min Max. Ry Xcg
Ix Ix Sx Sx Sy Sy
cm4 cm4 cm3 cm3 cm cm4 cm4 cm3 cm3 cm cm
180ES20 390.5 387.20 43.40 37.00 7.21 74.10 37.10 12.70 27.90 3.14 2.656
180ES25 484.1 484.30 53.80 48.45 7.19 92.50 46.30 15.90 34.70 3.14 2.667

Based on reduction factor of 0.40 for simple span with 33% increase on allowable stresses for wind load application and with fully
unbraced compression flange.
DESIGN SHEET Page 84 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


EAVE STRUT CAPACITY
ENCLOSED PARTIALLY OPEN
BUILDING ENCLOSED BUILDING
BUILDING
180ES20 180ES25 180ES20 180ES25 180ES20 180ES25
B V H MW Pall Pall MW Pall Pall MW Pall Pall
(M) (KM/Hr (M) (KN.M) (KN) (KN) (KN.M) (KN) (KN) (KN.M) (KN) (KN)
)
6 1.22 75.5 109.9 1.72 61.6 95.3 0.86 87.6 122.5
110 8 1.35 71.7 106.0 1.88 57.3 90.7 0.95 84.3 119.1
10 1.46 68.7 102.7 2.03 53.8 87.0 1.03 81.7 116.3
6 1.81 59.2 92.7 2.50 42.9 75.3 1.30 73.4 107.7
6.00 130 8 1..99 54.7 88.0 2.73 37.8 69.9. 1..43 69.5 103.6
10 2.13 51.2 84.2 2.93 33.7 65.5 1.54 66.4 100.4
6 2.49 42.9 75.4 3.40 24.2 55.3 1.81 59.3 92.8
150 8 2.73 37.9 70.0 3.72 18.3 49.0 1.98 54.8 88.1
10 2..92 33.8 65.6 3.98 13.6 43.9 2.13 51.3 84.3
6 1.91 40.5 64.4 3.68 28.2 51.6 1.34 50..9 75.1
110 8 2.11 37.2 61.0 2.94 24.3 47.4 1.49 48.1 72.3
10 2.28 34.5 58.2 3.16 21.1 44.1 1.61 45.9 70.0
6 2.83 26.0 49.2 3.90 11.1 33.4 2.02 38.7 62.5
7.5 130 8 3.10 22.0 45.0 4.27 6.3 28.4 2.23 35.3 59.0
10 3.33 18.7 41.6 4.57 2.5 24.3 2.40 32.5 56.1
6 3.89 11.2 33.5 5.32 N.A. 14.8 2.82 26.1 49.3
150 8 4.26 6.50 28.5 5.81 N.A. 8.9 3.10 22.1 45.1
10 4.56 2.60 24.4 6.22 N.A. 4.1 3.33 18.8 41.6
6 2.76 19.8 37.0 3.86 N.A. 25.3 1.93 29.1 46.7
110 8 3.04 16.8 34.0 4.24 N.A. 21.5 2.14 26.7 44.1
10 3.28 14.4 31.4 4.56 N.A. 18.4 2.32 24.6 42.0
6 4.07 6.60 23.2 5.61 N.A. 8.4 2.91 18.2 35.3
9.00 130 8 4.47 2.80 19.2 6.14 N.A. 3.7 3.21 15.1 32.1
10 4.80 N.A. 16.0 6.58 N.A. N.A. 3.46 12.5 29.4
6 5.61 N.A. 8.5 7.66 N.A. N.A. 4.06 6.6 23.2
150 8 6.13 N.A. 3.8 8.36 N.A. N.A. 4.46 2.9 19.3
10 6.57 N.A. N.A. 8.95 N.A. N.A. 4.79 N.A. 16.1

NOTES : The following are the data followed for the above table :
1. Building is enclosed, Gcp -1.2; partially enclosed building Gcp = -1.6; open building Gcp = -0.9.
2. Roof angle a  10.
3. First purlin is at a distance of 1100 mm. from eave.
4. Design is as per AISI 1986.
5. The allowable stresses have been increased by 331/3 % due to wind.
NOTATION :
B = Bay Spacing (M); V = Wind Speed (KM/Hr.); H = Eave Height (M);
Mw = Bending Moment Due to Wind Uplift (KN.M); Pall = Allowable Axial Load (KN)
DESIGN SHEET Page 85 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


How
ASFAD
(Advanced Steel Frame Analysis & Design)
Works

1.Introduction:
ASFAD is a Sructural Analysis and Design package developed by Zamil Steel to satisfy the
requirements of the Pre-Egineered Steel Buildings industry. The package was developed using C++
language utilizing the latest programming , analysis and design techniques. It has many features to
facilitate design of various elements and to ensure the economy , safety , uniformity and high quality
of the structural designs.

2.Structural Modeling:
Structural modeling is based on dividing the Structure into Members which connect to each other at
common points called Nodes.
Nodes are defined by their X and Y (Horizontal & Vertical) Coordinates according to the Structure’s
Global Coordinate System that is common for all Nodes and Members..
Members are defined by their Start and End Nodes and by their properties which may vary along
their lengths. Members may be broken into several Sections each of which is defined by its
respective length and properties.
The above basic model simulates the actual behavior of a Structure by including the Support
conditions and the Members’ end conditions.

3. Analysis Method:
The method used for the analysis of a Structure is the Stiffness Matrix Method.
Members may have variable properties along their lengths. Such Members are called non-prismatic
elements and the stiffness coefficients for such Members are calculated by numerical integration
techniques.
End forces at Nodes due to intermediate Members’ Loading are also calculated by the same
numerical integration techniques.
The numerical integration technique is based on the Energy Method which is achieved by dividing a
Member into Segments (Members are broken into Sections and Section are broken into Segments) .
The accuracy of this method depends on the length of Segment and number of Segments in the
Member. Analysis results for different models have proven that the use of a 0.5 meter Segment and a
minimum of 10 Segments per Member leads to very accurate and acceptable results.
DESIGN SHEET Page 86 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


4. Loads:
Loading is defined by specifying various Load Cases , Load Categories & Load Conditions.

A Load Case is a set of Nodal Loads & Member Loads that act simultaneously.
Example: Dead , Live , Wind (Windleft or Windright or Windend)
Crane (Crane-1 or Crane-2 or Crane-3 or Crane-4) , Seismic.
A Load Category is a group of various Load Cases that will never act simultaneously.
Example: The Load Category “Wind” contains three Load Cases:
- Windright
- Windleft
- Windend
A Load Condition is a combination of Load Categories. When a Load condition is specified the
program will internally generate all the possible Load Case combinations that result from the Load
Condition. Each Member will be checked for the most critical Load Case combination.
Example: The Load Condition “Dead + Wind + Crane”

Dead Wind Crane


+ +
Category Category Category

Load Cases Dead Wind right Crane-1


within Wind left Crane-2
Category Wind end Crane-3
Crane-4

Dead + Wind right + Crane-1


Dead + Wind right + Crane-2
Dead + Wind right + Crane-3
Dead + Wind right + Crane-4

All Possible Dead + Wind left + Crane-1


Load Case Dead + Wind left + Crane-2
Combinations Dead + Wind left + Crane-3
Dead + Wind left + Crane-4

Dead + Wind end + Crane-1


Dead + Wind end + Crane-2
Dead + Wind end + Crane-3
Dead + Wind end + Crane-4
DESIGN SHEET Page 87 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

As shown in the above example categorizing Load Cases makes one Load Condition sufficient to specify
all possible 12 Load Case combinations rather than specifying each of them individually.

5. Wind Load Generation:

Wind Load is generated based on the Basic Wind speed and other building parameters as per
ASCE7-05 editions , UBC 91 or BS CP3 1972. The Building height used is the maximum of the
right or left Eave height.
However other codes may be used by providing the wind Load on each member.

6. Design Module:

The ASFAD Design Module performs Design check as per AISC Ninth edition 1989 or BS 5950
Part 1 : 1990. All the Sections within a Members are checked Segment by Segment and the most
critical point within the section is reported for Bending & Axial stresses , Shear stresses &
Deflections.
Since Members are non-prismatic elements the Critical Buckling Load is determined for the whole
Member using numerical integration techniques. This will simulate the actual Buckling behaviour of
the non-prismatic Member accurately rather than analyzing the Member at each segment individually
which does not take into effect the interaction of all Segments when they behave as one Member.
DESIGN SHEET Page 88 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By

RIGID FRAME - CONNECTION PACKAGE


DESIGN SHEET Page 89 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


DESIGN SHEET Page 90 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


DESIGN SHEET Page 91 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


DESIGN SHEET Page 92 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


DESIGN SHEET Page 93 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


DESIGN SHEET Page 94 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


DESIGN SHEET Page 95 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


FIXED BASE DETAILS
DESIGN SHEET Page 96 of
Job No. Building No. Rev. No. 00

Customer Logistics Solution Provider Date

Description Designed ByChecked By


FIXED BASE DETAILS

You might also like