Scribd
Upload
82 views

EPM300 Data Sheet

This document provides data and specifications for the EPM 300 and EPM 300C field intensity meters. The EPM 300C helps installers find the optimal position for mounting wireless devices using the EnOcean protocol. It has sensors, signal indicators, and modes for testing radio links and repeater positioning. The EPM 300 is CE certified while the EPM 300C conforms to FCC requirements. Both are intended as OEM products to be brought to market and supported by local manufacturers.

Uploaded by

bearded79
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
82 views

EPM300 Data Sheet

This document provides data and specifications for the EPM 300 and EPM 300C field intensity meters. The EPM 300C helps installers find the optimal position for mounting wireless devices using the EnOcean protocol. It has sensors, signal indicators, and modes for testing radio links and repeater positioning. The EPM 300 is CE certified while the EPM 300C conforms to FCC requirements. Both are intended as OEM products to be brought to market and supported by local manufacturers.

Uploaded by

bearded79
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

DATA SHEET

Field Intensity Meter


EPM 300 / EPM 300C
(OEM Product)

EPM 300(C) is a mobile device for radio


link range testing. It helps electrical
installers to find the right position to
mount products supporting EnOcean
protocol.

EPM300 is equipped with two sensor switches for


Signal indicators:
on/off and mode selection. It will operate with
two AA size primary batteries.
 Signal high (green) indicates a very
well received radio telegram. All kind of
EPM 300 (868Mhz) is CE certified and conforms
EnOcean receivers/transceivers can be
to the R&TTE EU directive on radio equipment.
placed.
EPM 300C (315Mhz) conforms to the FCC IC re-
quirements.
 Signal low (yellow) indicates a received
telegram with medium field intensity
EPM 300 and EPM 300C are designed and pro-
duced as OEM products. They will be brought to (RSSI) level. An external antenna or re-
market by local OEM manufacturers. They are not peater is recommended.
considered to be finished end products in terms
of documentation, packaging and WEEE (elec-  No installation (red) indicates a very
tronic waste regulation). EnOcean will not be low RSSI level, installation is not recom-
reliable for consequences of any HW or SW mended.
changes/modifications of the EPM 300(C) done by
the first marketer. Product warranty and support  Signal valid (green) means a valid
will be covered by the OEM. EnOcean telegram has been received
otherwise it can be a disturbing signal on
EPM 300(C) modes:
the same frequency.

 Hold short will indicate every signal for


OEM label: 43 x 20mm
about 0,5s, this is used to track radio activi-
Housing: 110 x 70 x 25mm
ties with a short period e.g. push and release
Weight: 85g (w/o battery)
telegram of PTM switches.
Battery: AA/LR06 primary cell
Oper. temp.: 0°C - +40°C
 Hold long will indicate every signal for about Stor. temp.: -25°C - +65°C
1min. This is used to track telegrams with Oper. humidity: 0% - 95% r.h.
several seconds time gap. Stor. humidity: 0% - 98% r.h.
Prot. category: IP54
 Repeater mode can be used to find the best R&TTE: EN 300 220 (868Mhz)
position for 1-level repeater. FCC: CFR-47 Part15 (315 Mhz)
RoHS: yes
 Radio Link Test (RLT) will send telegrams
periodically every 2s. This mode can be used Type Ordering Code
to simulate a sensor /switch or to perform
EPM 300 S3004-J300
radio link statistic tests.
EPM 300C S3034-J300

EnOcean GmbH Phone +49.89.67 34 689-77 Product Marketing


Kolpingring 18a Fax +49.89.67 34 689-50 Subject to modifications
82041 Oberhaching [email protected] August 2010
Germany www.enocean.com

You might also like