Scribd
Upload
187 views

1.method Validation

The document discusses analytical method validation which establishes that a method is reliable, accurate, specific and precise for its intended use. Common validation characteristics include accuracy, precision, specificity, detection limit, quantitation limit, linearity and range. Accuracy is determined by recovery studies across multiple concentration levels in triplicate. Precision studies include repeatability, intermediate precision and reproducibility. Specificity shows the method can accurately measure the analyte in the presence of other components. Linearity is established by a proportional relationship between concentration and response within a given range. Detection and quantitation limits are the lowest concentrations that can be detected and quantified.

Uploaded by

Kalaivani V
Copyright
© © All Rights Reserved
Available Formats
Download as ODT, PDF, TXT or read online on Scribd
187 views

1.method Validation

The document discusses analytical method validation which establishes that a method is reliable, accurate, specific and precise for its intended use. Common validation characteristics include accuracy, precision, specificity, detection limit, quantitation limit, linearity and range. Accuracy is determined by recovery studies across multiple concentration levels in triplicate. Precision studies include repeatability, intermediate precision and reproducibility. Specificity shows the method can accurately measure the analyte in the presence of other components. Linearity is established by a proportional relationship between concentration and response within a given range. Detection and quantitation limits are the lowest concentrations that can be detected and quantified.

Uploaded by

Kalaivani V
Copyright
© © All Rights Reserved
Available Formats
Download as ODT, PDF, TXT or read online on Scribd
You are on page 1/ 4

METHOD VALIDATION OF

ANALYTICAL PROCEDURES

INTRODUCTION
Validation of an analytical procedure is the process by which it is established, by
laboratory studies, that the performance characteristics of the procedure meet
the requirements for the intended analytical applications. Method validation
provides an assurance of reliability during normal use, and is sometime referred
to as “the process for providing documented evidence that the method does what
it is intended to do.” The main objective of the validation is to demonstrate that
the analytical method is suitable for its intended purpose, is accurate, specific and
precise over the specified range that an analyte will be analyzed. Analytical
Method Validation is to be performed for new analysis methods or for current
methods when any changes are made to the procedure, composition of the drug
product and synthesis of the drugs substances

Common types of analytical procedure that can be validated


• Identification tests;
• Quantitative tests for impurities content;
• Limit tests for the control of impurities;
• Quantitative tests of the active moiety in samples of drug substance or drug
product or other selected component(s) in the drug product.
Typical validation characteristics which should be considered are listed below:
• Accuracy
• Precision
• Specificity
• Detection Limit
• Quantitation Limit
• Linearity
• Range
• Robustness

Methods and Terminology


1. Accuracy
The accuracy of an analytical method is the closeness of the test results obtained
by that method to the true value. This is sometimes termed trueness. It is
recommended that accuracy should be determined using a minimum of nine
determinations over a minimum of the three concentration levels, covering the
specified range (3 concentrations/3 replicates each of total analytical procedures).
[4]

It is measured as the percent of analyte recovered by assay. The recovery can be


determined by the equation:
Recovery = Analytical Result x 100% True Value
The recovery should be in the range of Control limit.
The following method can be applied for calculating the Upper Control Limit (UCL)
and Lower Control Limit (LCL). The method involves the moving range, which is
defined as the absolute difference between two consecutive measurements .
These moving range are averaged and used in the following formulae
. Precision
The precision of an analytical method is the degree of agreement among
individual test results when the method is repeated to multiple samplings of a
homogeneous sample.[6] The precision of an analytical procedure is usually
expressed as the standard deviation or relative standard deviation (coefficient of
variation) of a series of measurements.It is indicated by Relative Standard
Deviation, RSD, which is determined by the equation

Where xi is an individual measurement in a set of n measurement and is the


arithmetic mean of the set. Generally, the RSD should not be more than 2%.
2.1Repeatability
Repeatability refers to the use of the analytical procedure within a laboratory over
a short period of time using the same analyst with the same equipment. [3]
Repeatability should be assessed using a minimum of nine determinations
covering the specified range for the procedure (i.e., three concentrations and
three replicates of each concentration or using a minimum of six determinations
at 100% of the test concentration)
2.2Reproducibility
Reproducibility expresses the precision between laboratories (collaborative
studies, usually applied to standardisation of methodology). Reproducibility is
usually demonstrated by means of an inter-laboratory trial.
2.3Intermediate Precision
Intermediate precision is the results from within lab variations due to random
events such as different days, different analysts, different equipment, etc.
The standard deviation, relative standard deviation (coefficient of variation) and
confidence interval should be reported for each type of precision investigated.
3. Specificity
Specificity is the ability to measure accurately and specifically the analyte of
interest in the presence of other components that may be expected to be present
in the sample matrix such as impurities, degradation products and matrix
components. It must be demonstrated that the analytical method is unaffected by
the presence of spiked materials (impurities and/or excipients).

4.Linearity
Linearity is the ability of the method to elicit test results that are directly, or by a
well-defined mathematical transformation, proportional to analyte concentration
within a given range. It should be established initially by visual examination of a
plot of signals as a function of analyte concentration of content. If there appears
to be a linear relationship, test results should be established by appropriate
statistical methods. Data from the regression line provide mathematical estimates
of the degree of linearity. The correlation coefficient, y-intercept, and the slope of
the regression line should be submitted.

5. Detection Limit and Quantitation Limit


The Detection Limit is defined as the lowest concentration of an analyte in a
sample that can be detected, not quantified. The Quantitation Limit is the lowest
concentration of an analyte in a sample that can be determined with acceptable
precision and accuracy under the stated operational conditions of the analytical
procedures. Some of the approaches to determine the Detection Limit and
Quantitation Limit are:

b. Signal to Noise
This approach can only be applied to analytical procedures that exhibit baseline
noise. Determination of the signal-to-noise ratio is performed by comparing
measured signals from samples with known low concentrations of analyte with
those of blank samples and establishing the minimum concentration at which the
analyte can be reliably detected for the determination of Detection Limit and
reliably quantified for the determination of Quantitation Limit..

You might also like