AP1117

1A LOW DROPOUT POSITIVE ADJUSTABLE

OR FIXED-MODE REGULATOR

Description Pin Assignments

AP1117 is a low dropout positive adjustable or fixed-mode SOT89-3L
regulator with 1A output current capability. The product is
voltage specifically designed to provide well-regulated supply ( Top View )
for low IC applications such as high-speed bus termination
3 VIN
and low current 3.3V logic supply. AP1117 is also well suited
for other applications such as VGA cards. AP1117 is 2 VOUT
guaranteed to have lower than 1.4V dropout at full load
current making it ideal to provide well-regulated outputs of 1 Adj (GND)
1.25 to 5.0 with 6.4V to 18V input supply. AP1117 is available
in commercial temperature grade. Tab is VOUT

Features SOT223-3L
• 1.4V Maximum Dropout at Full Load Current ( Top View )
• Fast Transient Response
3 VIN
• Output Current Limiting
• Built-in Thermal Shutdown 2 VOUT
• Good Noise Rejection
• 3-Terminal Adjustable or Fixed 1.5V, 1.8V, 2.5V, 3.3V, 1 Adj (GND)
5.0V
Tab is VOUT
• Lead Free Packages: SOT223-3L, TO252-3L, SOT89-3L,
TO263-3L and TO220-3L TO220-3L
• SOT223-3L, TO252-3L, SOT89-3L, TO263-3L and
TO220-3L: Available in “Green” Molding Compound ( Front View )
(No Br, Sb) 3 VIN
• Lead Free Finish/RoHS Compliant (Note 1) 2 VOUT
1 Adj (GND)
Applications
Tab is VOUT
• PC Peripheral
• Communication
TO252-3L and TO263-3L
( Top View )

3 VIN

2 VOUT

1 Adj (GND)

Tab is VOUT

Notes: 1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at
http://www.diodes.com/products/lead_free.html.

AP1117 1 of 11 September 2011

Document number: DS31009 Rev. 21 - 2 www.diodes.com © Diodes Incorporated
 AP1117
1A LOW DROPOUT POSITIVE ADJUSTABLE
OR FIXED-MODE REGULATOR

Typical Application Circuit

5V
5V C1
C1 10uF
10uF

VIN VIN

Vo
VOUT 3.3V/1A VOUT 2.5V/1A
R1
C2 121 Ω C2
GND Adj
22uF R2 22uF
121 Ω
Tab is VOUT Tab is VOUT

( 5V/3.3V fixed output ) ( 5V/2.5V ADJ output )

R2
Note: Vo = VREF × (1 + )
R1

Pin Descriptions

Pin Name I/O PIN # Description

A resistor divider from this pin to the VOUT pin and ground sets the output voltage
Adj (GND) I 1
(Ground only for Fixed-Mode).
The output of the regulator. A minimum of 10uF capacitor (0.15Ω ≤ ESR ≤ 20Ω) must
VOUT O 2
be connected from this pin to ground to insure stability.
The input pin of regulator. Typically a large storage capacitor is connected from this pin
to ground to insure that the input voltage does not sag below the minimum dropout
VIN I 3
voltage during the load transient response. This pin must always be 1.3V higher than
VOUT in order for the device to regulate properly.

Functional Block Diagram

VIN 3 2 VOUT

- +
+ 1.25V
CURRENT 1
LIMIT
GND
+ (FIXED)

Thermal
Shutdown 1 Adj
-

AP1117 2 of 11 September 2011

Document number: DS31009 Rev. 21 - 2 www.diodes.com © Diodes Incorporated
 AP1117
1A LOW DROPOUT POSITIVE ADJUSTABLE
OR FIXED-MODE REGULATOR

Absolute Maximum Ratings

Symbol Parameter Rating Unit

VIN DC Supply Voltage -0.3 to 18 V
TMJ Maximum Junction Temperature 150 °C
Power Dissipation
SOT89-3L
Internally limited by maximum
SOT223-3L
PD junction temperature mW
TO220-3L
of 150 °C (Note 2)
TO252-3L
TO263-3L
TST Storage Temperature -65 to +150 °C
Notes: 2. AP1117 contains an internal thermal limiting circuit that is designed to protect the regulator in the event that the maximum junction temperature
exceeded. When activated, typically at 150°C, the regulator output switches off and then back on as the die cools.

Recommended Operating Conditions

Symbol Parameter Min Max Unit

TOP Operating Junction Temperature Range 0 125 °C

Electrical Characteristics (Under Operating Conditions)

Parameter Conditions Min Typ. Max Unit

o
TA = 25 C, (VIN-OUT) = 1.5V
Reference Voltage AP1117-ADJ 1.225 1.250 1.275 V
IO = 10mA
IOUT = 10mA, TA = 25oC,
AP1117-1.5 1.470 1.500 1.530 V
3V ≤ VIN ≤ 12V
IOUT = 10mA, TA = 25oC,
AP1117-1.8 1.764 1.800 1.836 V
3.3V ≤ VIN ≤ 12V
IOUT = 10mA, TA = 25oC,
Output Voltage AP1117-2.5 2.450 2.500 2.550 V
4V ≤ VIN ≤ 12V
IOUT = 10mA, TA = 25oC,
AP1117-3.3 3.235 3.300 3.365 V
4.8V ≤ VIN ≤ 12V
IOUT = 10mA, TA = 25oC,
AP1117-5.0 4.900 5.000 5.100 V
6.5V ≤ VIN ≤ 12V
IO = 10mA,VOUT+1.5V < VIN < 12V,
Line Regulation AP1117-XXX 0.2 %
TA = 25oC
VIN = 3.3V, VADJ = 0, 0mA < IO < 1A,
AP1117-ADJ o 1 %
TA = 25 C (Note 3, 4)
VIN = 3V, 0mA < IO < 1A,
AP1117-1.5 o 12 15 mV
TA = 25 C (Note 3, 4)
Load Regulation
VIN = 3.3V, 0mA < IO < 1A,
AP1117-1.8 15 18 mV
TA = 25oC (Note 3, 4)
VIN = 4V, 0mA < IO<1A,
AP1117-2.5 20 25 mV
TA = 25oC (Note 3, 4)

AP1117 3 of 11 September 2011

Document number: DS31009 Rev. 21 - 2 www.diodes.com © Diodes Incorporated
 AP1117
1A LOW DROPOUT POSITIVE ADJUSTABLE
OR FIXED-MODE REGULATOR

Electrical Characteristics (Under Operating Conditions) (cont.)

Parameter Conditions Min Typ. Max Unit

VIN = 5V, 0 ≤ IOUT ≤ 1A,
AP1117-3.3 o 26 33 mV
Load Regulation TA = 25 C (Note 3, 4)
(cont.) VIN = 8V, 0 ≤ IOUT ≤ 1A,
AP1117-5.0 40 50 mV
TA = 25oC (Note 3, 4)
Dropout Voltage AP1117-ADJ/1.5/1.8 IOUT = 800mA, ΔVOUT = 1%VOUT
1.2 1.3 V
(VIN-VOUT) /2.5/3.3/5.0 0oC ≤ TJ ≤ 125oC
Dropout Voltage AP1117-ADJ/1.5/1.8 IOUT = 1A, ΔVOUT = 1%VOUT
1.3 1.4 V
(VIN-VOUT) /2.5/3.3/5.0 0oC ≤ TJ ≤ 125oC
AP1117-ADJ/1.5/1.8
Current Limit (VIN-VOUT) = 5V 1. 1 A
/2.5/3.3/5.0
Minimum Load Current o o
AP1117-XXX 0 C ≤ TJ ≤ 125 C 5 10 mA
(Note 5)
Thermal Regulation TA = 25oC, 30ms pulse 0.008 0.04 %/W
F = 180Hz, COUT = 25uF Tantalum, IOUT = 1A
Ripple Rejection
AP1117-XXX VIN = VOUT+3V 60 70 dB
Temperature Stability IO = 10mA 0.5 %
SOT89-3L: Control Circuitry/Power Transistor (Note 6) 164
SOT223-3L: Control Circuitry/Power Transistor (Note 7) 107
θJA Thermal Resistance
TO252-3L: Control Circuitry/Power Transistor (Note 6) 73 °C/W
Junction-to-Ambient θJA
TO220-3L: Control Circuitry/Power Transistor (Note 6) 78
TO263-3L: Control Circuitry/Power Transistor (Note 6) 60
SOT89-3L: Control Circuitry/Power Transistor (Note 6) 42
SOT223-3L: Control Circuitry/Power Transistor (Note 7) 15
θJC Thermal Resistance
TO252-3L: Control Circuitry/Power Transistor (Note 6) 12 °C/W
Junction-to-Case
TO220-3L: Control Circuitry/Power Transistor (Note 6) 3.5
TO263-3L: Control Circuitry/Power Transistor (Note 6) 3.5
Notes: 3.See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant
junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead = 1/18” from the package.
4. Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the difference
between input and output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output
range.
5. Quiescent current is defined as the minimum output current required in maintaining regulation. At 12V input/output differential the
device is guaranteed to regulate if the output current is greater than 10mA.
6. Test conditions for SOT89-3L, TO220-3L, TO252-3L and TO263-3L: Devices mounted on FR-4 substrate, single sided PC board, 2oz copper, with
minimum recommended pad layout, no air flow. The case point of θJC is located on the thermal tab.
7. Test conditions for SOT223-3L: Devices mounted on FR-4 substrate, single sided PC board, 2oz copper, with 5mmx5mm thermal pad layout, no
air flow. The case point of θJC is located on the thermal tab.

AP1117 4 of 11 September 2011

Document number: DS31009 Rev. 21 - 2 www.diodes.com © Diodes Incorporated
 AP1117
1A LOW DROPOUT POSITIVE ADJUSTABLE
OR FIXED-MODE REGULATOR

Typical Performance Characteristics

2.0 0.20
1.8

OUTPUT VOLTAGE DEVIATION (%)

1.6 0
DROPOUT VOLTAGE (V)

ILOAD = 800mA
1.4
TJ = 25°C
1.2 -0.20

1.0

0.8 -0.40
TJ = 125°C
0.6

0.4 -0.80

0.2
0 -1
0 250 500 750 1000 -40 0 25 50 75 100 125
OUTPUT CURRENT (mA) TEMPERATURE (°C)
Dropout Voltage vs. Output Current Load Regulation vs. Temperature

2 1

1.5
OUTPUT VOLTAGE DEVIATION (%)
OUTPUT VOLTAGE CHANGE (%)

0.8
1

0.5
0.6

-0.5 0.4

-1
0.2
-1.5

-2 0
-40 -25 0
25 50 75 100 125 150 2 4 6 8 10 12
TEMPERATURE (°C) INPUT VOLTAGE (V)
Percent Change in Output Voltage vs. Temperature Line Regulation
7.5 30
CIN = 1µF CIN = 1µF
COUT = 10µF Tantalum COUT = 10µF Tantalum
OUTPUT VOLTAGE DEVIATION (mV)

OUTPUT VOLTAGE DEVIATION (mV)

20
6.5 Preload = 100mA
10
LOAD CURRENT (A)
INPUT VOLTAGE (V)

5.5
0
40 -10

-20
20
2
0
1

-20 0

-1
-40
0 20 40 60 80 100 120 140 160 180 200 0 10 20 30 40 50 60 70 80 90 100
TIME (µs) TIME (µs)
Line Transient Response Load Transient Response

AP1117 5 of 11 September 2011

Document number: DS31009 Rev. 21 - 2 www.diodes.com © Diodes Incorporated
 AP1117
1A LOW DROPOUT POSITIVE ADJUSTABLE
OR FIXED-MODE REGULATOR

Ordering Information

A P 1 1 1 7 X XX X - X

Package Vout Lead Free Packing

D : TO252-3L Blank : Adj L : Lead Free U : Tube
E : SOT223-3L 15 : 1.5V G : Green 13 : Tape & Reel
K : TO263-3L 18 : 1.8V
T : TO220-3L 25 : 2.5V
Y : SOT89-3L 33 : 3.3V
50 : 5.0V

Tube 13” Tape and Reel

Package Packaging
Device Part Number
Code (Note 8) Quantity Quantity Part Number Suffix
Suffix
AP1117DXXL-13 D TO252-3L NA NA 2500/Tape & Reel -13
AP1117DXXG-13 D TO252-3L NA NA 2500/Tape & Reel -13
AP1117EXXL-13 E SOT223-3L NA NA 2500/Tape & Reel -13
AP1117EXXG-13 E SOT223-3L NA NA 2500/Tape & Reel -13
AP1117KXXL-13 K TO263-3L NA NA 800/Tape & Reel -13
AP1117KXXG-13 K TO263-3L NA NA 800/Tape & Reel -13
AP1117TXXL-U T TO220-3L 50 -U NA NA
AP1117TXXG-U T TO220-3L 50 -U NA NA
AP1117YXXL-13 Y SOT89-3L NA NA 2500/Tape & Reel -13
AP1117YXXG-13 Y SOT89-3L NA NA 2500/Tape & Reel -13
Notes: 8. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at
http://www.diodes.com/datasheets/ap02001.pdf.

Marking Information

(1) SOT223-3L

( Top View )

Y : Year : 0~9
Logo YWX W : Week : A~Z : 1~26 week;
Part Number a~z : 27~52 week;
1117 for ADJ 1 7-VV z repersents 52 and 53 week
X : Internal code
17-VV:15 for 1.5V a~z : Lead Free
18 for 1.8V A~Z : Green
25 for 2.5V
33 for 3.3V
50 for 5.0V

AP1117 6 of 11 September 2011

Document number: DS31009 Rev. 21 - 2 www.diodes.com © Diodes Incorporated
 AP1117
1A LOW DROPOUT POSITIVE ADJUSTABLE
OR FIXED-MODE REGULATOR

Marking Information (cont.)

(2) TO252-3L
( Top View )

Logo L : Lead Free

G : Green
Part Number 17-VV YY : Year : 01~09
1117 for ADJ YY WW X X
17-VV:15 for 1.5V WW : Week : 01~52, 52 represents
18 for 1.8V 52 and 53 week
25 for 2.5V X : Internal Code
33 for 3.3V
50 for 5.0V

(3) SOT89-3L
( Top View )
XX : Identification code
XX Y : Year : 0~9
W : Week : A~Z : 1~26 week;
Y W X a~z : 27~52 week;
z represents 52 and 53 week
1 2 3 X : Internal code
a~z : Lead Free
A~Z : Green

Marking Code Table

Identification Code Output Version
DA AP1117-ADJ
DB AP1117-1.5V
DC AP1117-1.8V
DD AP1117-2.5V
DE AP1117-3.3V
DF AP1117-5.0V

(4) TO263-3L
( Top View )

Logo L : Lead Free

G : Green
Part Number 1117-VV YY : Year : 01~09
VV: 15 for 1.5V YY WW X X WW : Week : 01~52, 52 represents
18 for 1.8V 52 and 53 week
25 for 2.5V X : Internal code
33 for 3.3V
50 for 5.0V
Blank for ADJ

AP1117 7 of 11 September 2011

Document number: DS31009 Rev. 21 - 2 www.diodes.com © Diodes Incorporated
 AP1117
1A LOW DROPOUT POSITIVE ADJUSTABLE
OR FIXED-MODE REGULATOR

Marking Information (cont.)

(5) TO220-3L
( Top View )

Logo L : Lead Free

G : Green
Part Number 17 - VV
1117 for ADJ YY : Year : 01~09
17-VV : 15 for 1.5V YY WW X X WW : Week : 01~52, 52 represents
18 for 1.8V 52 and 53 week
25 for 2.5V X : Internal code
33 for 3.3V
50 for 5.0V

Package Outline Dimensions (All Dimensions in mm)

(1) Package Type: SOT223-3L

AP1117 8 of 11 September 2011

Document number: DS31009 Rev. 21 - 2 www.diodes.com © Diodes Incorporated
 AP1117
1A LOW DROPOUT POSITIVE ADJUSTABLE
OR FIXED-MODE REGULATOR

Package Outline Dimensions (All Dimensions in mm) (cont.)

(2) Package Type: TO252-3L

0.88/1.27
5.6
6.45/6.70 Typ 6.58
5.20/5.50 Typ 5.35

5.6
5.40/6.20

11.0
Typ 5.57

7.2
2.25

2.0
1.2
0.61 Typ 2.28 Land Pattern Recommendation (Unit: mm)
0.64/1.02
BSC. 2.18/2.40
4.57 BSC. Typ 0.83 0.89/
9.00/10.40 Typ 9.70 Typ 2.29
1.14

0.45/0.58 0.51 SEE NOTE2 SEATING

Typ 0.52 PLANE 0.45/0.58
Typ 0.52

(3) Package Type: SOT89-3L

1.40/1.75
Typ 1.60 1.7
2.35/2.60 Typ 2.48

2.7
3.94/4.25

0.4
1.9

1.3
0.80/
1.20

1.45/1.55
Typ 1.50 0.9 1.5
2.90/3.10 Land Pattern Recommendation (Unit: mm)
Typ 3.00
50 (2x)
80 (2x)
4.40/4.60 Typ 4.50
1.40/1.60
Typ 1.50

0.36/0.48 0.41/0.53 0.36/0.48 0.35/0.43

Typ 0.42 Typ 0.47 Typ 0.42 Typ 0.39

AP1117 9 of 11 September 2011

Document number: DS31009 Rev. 21 - 2 www.diodes.com © Diodes Incorporated
 AP1117
1A LOW DROPOUT POSITIVE ADJUSTABLE
OR FIXED-MODE REGULATOR

Package Outline Dimensions (All Dimensions in mm) (cont.)

(4) Package Type: TO263-3L

Typ 1.30
2.92
10.9
9.65/10.29 Typ 9.97

14.61/15.88 Typ 15.24

8.65/9.65 Typ 9.15

9.1

15.7
3
1.27/
1.78

1.52
Typ

1.3 2.54
2.54
BSC . 0.51/0.99 Typ 0.75 Land Pattern R ecom mendation (U nit: m m)
1.14/1.40 Typ1.27
0.38 Typ

4.06/4.83
Typ 4.45
2.28/2.80 Typ 2.54

1.14/1.40
Typ 1.27
(5) Package Type: TO220-3L

3.55/4.85
2.54/3.43 9.70/10.70 0.51/1.40
Ø3.53/4.09 Typ 4.20
Typ 2.98 Typ 10.20 Typ 0.95
Typ 3.81
SEATING PLANE

5.84/6.86
Typ 6.35
14.20/16.50
Typ 15.35

3.66/6.35
Typ 5.00
12.72/14.72
Typ 13.72

1.14/1.78
Typ 1.46

0.31/1.14
0.51/1.14 Typ 0. 72
Typ 0.83
2.99/2.79 2.03/2.92
4.83/5.33 Typ 2.54 Typ2.48
Typ 5.08

AP1117 10 of 11 September 2011

Document number: DS31009 Rev. 21 - 2 www.diodes.com © Diodes Incorporated
 AP1117
1A LOW DROPOUT POSITIVE ADJUSTABLE
OR FIXED-MODE REGULATOR

IMPORTANT NOTICE

DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS
DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).

Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other
changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability
arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any
license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described
herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies
whose products are represented on Diodes Incorporated website, harmless against all damages.

Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized
sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall
indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.

Products described herein may be covered by one or more United States, international or foreign patents pending. Product names
and markings noted herein may also be covered by one or more United States, international or foreign trademarks.

LIFE SUPPORT

Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without
the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:

A. Life support devices or systems are devices or systems which:

1. are intended to implant into the body, or

2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided
in the labeling can be reasonably expected to result in significant injury to the user.

B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected
to cause the failure of the life support device or to affect its safety or effectiveness.

Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or
systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements
concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems,
notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further,
Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes
Incorporated products in such safety-critical, life support devices or systems.

Copyright © 2011, Diodes Incorporated

www.diodes.com

AP1117 11 of 11 September 2011

Document number: DS31009 Rev. 21 - 2 www.diodes.com © Diodes Incorporated