Scribd
Upload
1K views

Bosch 5.3 Esp Coding Wiki

This document provides instructions for recoding the ABS/ESP controller on Volkswagen and Audi vehicles equipped with Bosch 5.3 ESP. It requires entering specific login and recode values using VAG-COM diagnostic software depending on the vehicle's engine, transmission, and brake components. The procedure involves logging in to the controller, entering the recode value and a WSC, and performing a steering angle sensor calibration to store the centered wheel position.

Uploaded by

Cristian Sindie
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
1K views

Bosch 5.3 Esp Coding Wiki

This document provides instructions for recoding the ABS/ESP controller on Volkswagen and Audi vehicles equipped with Bosch 5.3 ESP. It requires entering specific login and recode values using VAG-COM diagnostic software depending on the vehicle's engine, transmission, and brake components. The procedure involves logging in to the controller, entering the recode value and a WSC, and performing a steering angle sensor calibration to store the centered wheel position.

Uploaded by

Cristian Sindie
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Ross-Tech: VAG-COM: ESP Coding Page 1 of 2

920 South Broad Street, Lansdale PA 19446,


Diagnostic Software for European Automobiles USA
Order Info F.A.Q. Download Manual Upgrades Literature Search:

Home
Products
VAG-COM
Support
Car Info & Procedures
ESP Coding

ESP Coding Info


Updated 20 Feb. 2006

Ross-Tech is not responsible for any damage or problems that may result from following these instructions.
They are to be used at your own risk. As always, you should refer to a Factory Repair Manual for your
vehicle!

This procedure details how to Recode the ABS/ESP controller in many VW/Audi vehicles (specifcally the B5
Passat and the B5 Audi A4/S4) equipped with Bosch 5.3 ESP (Electronic Stability Program). This procedure
should be performed if any of the following components have been removed or replaced:

 ABS/EDL/ASR/ESP control unit (J104)

 Steering Angle Sensor (G85)

First of all, make sure you have downloaded and installed the latest version of VAG-COM (Release 512.1 at
the time this page was created):

http://www.ross-tech.com/vag-com/download/current.html

Coding the ESP controller requires both a specific Login value and a specific Recode value, depending on
which engine, brakes, and transmission are in the vehicle. Locate your vehicle below:

Engine Transmission Brake Calipers Login Recode


4 cyl gasoline Manual Lucas C54 09675 04175
4 cyl gasoline Manual FN3 Teves/ATE 09575 04275
4 cyl gasoline Automatic Lucas C54 09677 04177
4 cyl gasoline Automatic FN3 Teves/ATE 09577 04277
6 cyl gasoline Manual FN3 Teves/ATE 09595 04295
6 cyl gas 2.7T Manual FN 2/ HP2 09495 04395
6 cyl gasoline Automatic FN3 Teves/ATE 09597 04297
6 cyl gas 2.7T Automatic FN 2/ HP2 09497 04397
4 cyl diesel Manual Lucas C54 09655 04155
4/6 cyl diesel Manual FN3 Teves/ATE 09555 04255
4 cyl diesel Automatic Lucas C54 09677 04177
4/6 cyl diesel Automatic FN3 Teves/ATE 09557 04257

(For example, an Audi S4 2.7T with a manual transmission would require a Login of 09495 and a Recode of
04395).

http://www.ross-tech.com/vag-com/cars/espcoding.html 12/10/2006
Ross-Tech: VAG-COM: ESP Coding Page 2 of 2

With the ignition on, but the engine not running:

[Select]
[03 - ABS Brakes]
[Login - 11]
Enter the appropriate Login value from the table.
[Do It!]
Make sure you don't get a Dropped Session message and that the cursor on the top left keeps spinning.
[Recode - 07]
Enter the appropriate Recode value from the table. Put in a WSC (anything will work, try 12345). It can NOT
be left as all zeros.
[Do It!]
Again, make sure the cursor is still spinning. Do NOT exit out of the controller yet.

If the above is not successful, try it with the engine running.

Next, do the steering angle sensor calibration:

[Login - 11]
Enter 40168
[Do It!]
[Basic Settings - 04]
Group 001
[Go!]

This will store the zero (centered) position of the steering wheel. There should be a displayed message that
reads: "Steer. angle sender compens OK". If you get an error, it may mean the Login was not successfully
performed.

Click the [Done, Go Back] button and you're all set.

Home
Products
VAG-COM
Support
Car Info & Procedures
ESP Coding

http://www.ross-tech.com/vag-com/cars/espcoding.html 12/10/2006

You might also like