Scribd
Upload
829 views

Fanuc Series 16 Backup Procedure

This document provides steps to backup and restore CNC machine parameters, programs, and settings to a computer. It involves: 1) Punching out NC parameters, PMC parameters, pitch error compensation data, macro variables, programs, and tool offsets to a computer. 2) Setting the CNC to receive data and designating the input and output files and locations. 3) Restoring involves inputting the backed up NC parameters, PMC parameters, pitch error compensation data, macro variables, programs, and tool offsets from the computer to the CNC. It also requires setting parameters to enable writing and protect programs.

Uploaded by

Yael Abraham Gutiérrez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
829 views

Fanuc Series 16 Backup Procedure

This document provides steps to backup and restore CNC machine parameters, programs, and settings to a computer. It involves: 1) Punching out NC parameters, PMC parameters, pitch error compensation data, macro variables, programs, and tool offsets to a computer. 2) Setting the CNC to receive data and designating the input and output files and locations. 3) Restoring involves inputting the backed up NC parameters, PMC parameters, pitch error compensation data, macro variables, programs, and tool offsets from the computer to the CNC. It also requires setting parameters to enable writing and protect programs.

Uploaded by

Yael Abraham Gutiérrez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

Fanuc Series 16 / 18 / 21 Memory Backup Procedure

Fanuc 16B, 16C, 18B, 18C SRAM backup procedure SRAM Memory Card Informatoion
Fanuc 16i/ 18i/ 21i SRAM backup procedure (watch it on YouTube) CompactFlash Memory Card
Information
Step 1: Set up your Personal Computer (PC) or laptop to receive data. (click here for information on
RS232 setup)
Step 2: Punch out NC Parameters as follows
Select EDIT mode.
Select PARAMETER screen by pressing [SYSTEM] key and
(PARAM) softkey.
Press (OPRT) softkey and ( > ) right
arrow softkey.
Press (PUNCH) softkey and (EXEC)
softkey.
Step 3: Punch out PMC Parameters as follows
Select MDI mode.
Turn on Parameter Write Enable.
Press [SYSTEM] key and (PMC) softkey.
Press (PMCPRM) and (KEEPRL)
softkeys.
Move the cursor to K17 and set bit 1 to
“1”.
Select EDIT mode.
Press (<) and then (>) soft keys.
Press (I/O) softkey to set parameters for
I/O operation
CHANNEL NO. = Press “1” and
[INPUT] keys.
DEVICE NAME = Press (FDCAS)
softkey.
KIND OF DATA = Press (PARAM)
softkey.
FUNCTION =Press (WRITE) softkey.
FILE NO =Press [-] [1] [INPUT] keys.
Press (EXEC) softkey.

Step 4: Punch out Pitch Error Compensation


data as follows
Select EDIT mode.
Select PITCH ERROR COMPENSATION screen by pressing [SYSTEM] key and (PARAM),
(>), and (PITCH) softkeys.
Press (OPRT) and (>) soft keys.
Press (PUNCH) AND (EXEC) softkeys.

Step 5: Punch out Custom Macro Variables as


follows
Select EDIT mode.
Display TOOL OFFSET screen by
pressing [OFFSET] key.
Press (>) and then (MACRO) softkeys to display macro variable
screen.
Press (OPRT) and then (>) softkeys.
Press (PUNCH) and (EXEC) to output
variables No. 500 ~ 999.

Step 6: Punch out Part Programs as follows


Verify NC PRM 3202 bit 4 and bit 0 = 0. If “1”, 8000 and 9000 series programs are protected and
will not be output.
Select EDIT mode.
Select PROGRAM screen by pressing [PROG] key and (PRGRM)
softkey.
Press (OPRT) and (>) softkeys.
Key in “O-9999” to output all programs.
Press (PUNCH) and (EXEC) softkeys.

Step 7: Punch out Tool Offset Data as follows


Select EDIT mode.
Display to TOOL OFFSET screen by pressing [OFFSET] key and
(OFFSET) softkey.
Press (OPRT) and (>) softkeys.
Press (PUNCH) and (EXEC) softkeys.

Fanuc Series 16 / 18 / 21 Memory Restore Procedure

Depress EMERGENCY STOP button.


Verify correct communication parameters
from output procedure.
Step 1: Input CNC Parameters as follows
Display to PARAMETER screen by pressing [SYSTEM] key and
(PARAM) softkey.
Press (OPRT) and (>) softkey.
Press (READ) and (EXEC) softkeys.
Parameters will be input.
When input is complete, power the CNC
OFF and ON.
Parameter No. 1815 bit 5 set to “0” will disable an alarm 310 with an Absolute Pulse coder
system.

Step 2: Input PMC PARAMETERS as follows


Verify Parameter Write Enable = 1.
Press [SYSTEM] key and (PMC) softkey.
Press (PMCPRM), then (KEEPRL)
softkeys.
Move cursor to K17 and press [1], [0] and
[INPUT].
Select EDIT mode.
Press ( < ) and then ( > ) softkeys.
Press (I/O) softkey, and set parameters for
I/O operation.
CHANNEL NO=press [ 1 ] and [ INPUT ]
keys.
DEVICE NAME=press (FDCAS) softkey.
FUNCTION=press (READ) softkey.
FILE NO=PRESS [ 2 ] and [ INPUT ]
keys.
Press (EXEC) softkey to read PMC
parameters.

Step 3: Input PITCH ERROR COMPENSATION


data as follows
Select EDIT mode.
Verify Parameter Write Enable = 1.
Press [SYSTEM] key and (PARAM), ( > ),
and (PITCH) softkeys.
Press (OPRT) and ( > ) softkeys.
Press (READ) and (EXEC) softkeys to input
Pitch Error data.

Step 4: Input CUSTOM MACRO VARIABLES as


follows
Select EDIT mode.
Turn off the Program Protect key.
Press [PROGRAM] key and (PRGRM)
softkey.
Press ( > ) softkey.
Press [ O ] and [ 1 ] keys, then (READ) and
(EXEC) softkeys.
Select AUTO mode and execute program
O0001.
Verify variables were written to Macro
Variable table.
Delete program O0001.

Step 5: Input PART PROGRAMS as follows


Set the following parameters in MDI mode, if
necessary.
PRM 3201,bit 6 =1
PRM 3201, bit 1=0
PRM 3202, bit 4=0
PRM 3202, bit 0=0
Select EDIT mode.
Turn off the Program Protect key.
Press [PROGRAM] key and (PRGRM)
softkey.
Press ( > ) softkey.
Press (READ) and (EXEC) softkeys to read
part programs.

Step 6: Input TOOL OFFSETS as follows


Select EDIT mode.
Turn off the Program Protect key.
Press the [OFFSET] key and (OFFSET)
softkey.
Press the (OPRT) and the ( > ) softkeys.
Press the (READ) and (EXEC) softkeys to
read in Tool Offsets.

You might also like