GEOMETRIC DIMENSIONING AND TOLERANCING
Self Evaluation Date :22.12.18
1. H7 / g6 is a ……… fit.
(a) Clearance (b) Interference
(c) Transition (d) All the above
2. The tolerance zone for circular runout is ……………………
(a) Two parallel planes (b) Two coaxial circles
(c) Datum axis (d) Two coaxial cylinders
3. When diameter is controlled by circular runout, its maximum possible offset from the
datum axis is equal to ……… the runout tolerance value
(a) Same as (b) Double
(c) Half of (d) None of above
4. The runout control applies at …………….
(a) RFS (b) MMC
(c) LMC (d) VC
5. When the Runout applied to a diameter, it controls ………………
(a) Location (b) Orientation
(c) Circular (d) All the above
6. When a profile control is specified with datum reference it is related to ………..
(a) Form Control (b) Feature Control
(c) RFS (d) MMC
7. When a profile of a surface control is specified without datum reference, it is used as a
………………..
(a) Form Control (b) Feature Control
(c) RFS (d) MMC
8. A profile Control can be used to control ……………………
(a) Size (b) Location
(c) Orientation (d) All the above
9. Datums are ……………
a) Real b) Simulated c) Perfect d) Irregular and Flawed
e) Derived from datum features
(a) b,c,e (b) a,b,c (c) b,c,d (d) c,d,e
10. Features are ……………
a) Real b) Sur d) Always measurable for size
(a) a,b (b) b,c (c) c,d (d) d,a
11. Allowance is ………
(a) Difference between LMC of mating features (b) Difference between MMC of mating features
(c) Difference between shaft MMC and hole LMC (d) Difference between shaft LMC and hole MMC
12. The “Feature Control Frame” must be containing …….
(a) Modifiers and datum reference (b) Geometric characteristic symbol and tolerance
(c) Datum, tolerance and material condition symbol (d) All of the above
13. Flatness control tolerance zone is …………………..
(a) One perpendicular (b) Two parallel
(c) Two perpendicular (d) None of above
14. Whenever a straight control is associated with FOS dimension applies to the
…………… of FOS
(a) Axis (b) Center plane
(c) Axis or center plane (d) None of above
15. ……………………. is the only geometric control that can override Rule # 1
(a) Straightness of an FOS (b) Flatness
(c) Perpendicularit (d) Circularity
16. Tolerance zone for circularity control is…………..
(a) Two coaxial circles (b) Two coaxial cylinders
(c) Single plane (d) Single circle
17. When perpendicularity applied to surface, the shape of tolerance zone is …………
planes that are perpendicular to the datum plane(s)
(a) Two parallel (b) Two perpendicular
(c) Two inclined planes at an angle (d) None of the above
18. When perpendicularity is applied to surface, the zone of tolerance indirectly limits
the…………….. tolerance zone.
(a) Straightness (b) Circularity
(c) Flatness (d) Cylindricity
19. When angularity applied to a surface, ……………. of the surface elements must be
within the tolerance zone.
(a) Only one (b) All
(c) Two (d) None of the above
20. A ………. is a geometric tolerance that limits the amounts a surface, axis, or center
plane is permitted to vary from being parallel to the datum.
(a) Parallelism control (b) Parallelism
(c) Perpendicularity (d) All the above
21. A feature is any …………….. of a part.
(a) Surface (b) Line
(c) Point (d) Center line
22. Tangent plane modifier is used to control -------------
(a) Parallelism (b) Flatness
(c) Symmetry (d) Straightness
23. If “Controlled Radius” modifier is given, the part surface flats or reversals have ............
the tolerance zone
(a) Without (b) Within
(c) Zero (d) None of the above
24. Virtual condition for External FOS with M modifier is ………..
(a) MMC + Position tole (b) MMC - Position tole
(c) LMC + Position tole (d) LMC - Position tole
25. Symmetry is similar to ……………
(a) Run out (b) Orientation
(c) Position (d) Concentricity
ed
