Software version: Not version-specific

Last updated November 25, 2016 by Tekla Global Support

Using unfold_corner_ratios.inp
What is unfold_corner_ratios.inp?
Unfold_corner_ratios.inp is a file which contains information Tekla Structures uses to unfold
polybeams and thus measure their length. By using a “Ratio” value between 0-1, the file
indicates to Tekla Structures how the polybeam will be unfolded.
The file works by defining profile types and how they should be unfolded (that is, length
measured) based certain characteristics of the polybeam, such as whether it has straight or
curved chamfers, curvature radius, material type, profile, etc.

What variables a ect unfolded length of polybeams?

The unfold corner ratios is used differently depending on whether you have modeled
polybeams with straight or curved chamfers. Below is a flowchart which explains how
unfold_corner_ratios.inp interacts with other advanced options.

Cookies help us deliver this service. By using our services, you agree to our use of Accept Decline
cookies. More information
 How Tekla Structures reads unfold_corner_ratios.inp
The unfold_corner_ratios.inp file is read from the system folders, but it can also be placed in
a Firm, Project, or Model folder.
Tekla Structures will search for unfold_corner_ratios.inp in the same order as it does
normally with other files, that is, Model, Project, Firm, System (environment) folders. Tekla
Structures will use the first file it finds, and ignore any other. There is no merging of files.
unfold_corner_ratios.inp is not used with curved beams (that is, not polybeams, but beams
curved from the Beam Properties dialog box).

Format of unfold_corner_ratios.inp
The unfold_corner_ratios file is a text file which uses lines which represent certain types of
polybeams. The format of each line is as follows:

Cookies help us deliver this service. By using our services, you agree to our use of Accept Decline
cookies. More information
 Type:
• 1 is recommended for polybeams with any profile.
• 2 is recommended for polybeams with plate profile (for example, “PL” profiles)
• 3 is for parts which are not be unfolded and follow the old polybeam length calculation (see
the polybeam length flowchart above, XS_USE_OLD_POLYBEAM_LENGTH_CALCULATION). (For
example, the line 3 L* * disables unfolding of L profiles.)
These type values are not exclusive. Tekla Structures recognizes all polybeam types
(plates/non-plate profiles) regardless of whether, for example, “1” or “2” is used. The only
difference is that on the subsequent values specified on the inp file, Tekla Structures will
treat those numbers as being different things depending on which ‘Type’ value is used.
The following example will explain this more clearly. We have three polybeams, an I-beam of
300 mm thickness, and two plate polybeams with a PL300x20 profile.

 
For example, if the line used is

2 * * 0 1000 1 0 180 1
All polybeams will be considered (regardless of the Type= 2). The value “1000” will be
considered as a “Rotation” (in case Type = 1) or a “thickness” (in case Type =2). So for
example, if the value “1000” is changed to “299”, only the third polybeam will conform.
CookiesTekla
help us deliver thisuses
Sturctures service.
theBy using
solid our services,
extrema you agreethe
to determine to our Accept
use of of the
‘thickness’ Decline
part. For
cookies. More information
instance, for the I-beam and the second plate, the ‘thickness’ would be both 300mm. The
 thickness of the third plate would only be 20 mm, since it is rotated.
Similarly, if the line would read:

1 * * -180 180 1 0 180 1

The third and fourth values (“-180” and “180”) would be ‘Rotation’, according to Type =1. It
would apply to all polybeams though, regardless of their profile.
When a polybeam qualifies in more than one line of unfold_corner_ratios.inp, Tekla
Structures will unfold the polybeam according to the first line the polybeam applies to,
starting from the top of the file downwards. For example, if we had both lines:

2 * * 0 1000 1 0 180 1
1 * * -180 180 1 0 180 0
In this case, if a polybeam conforms to both line variables, then it would be unfolded using
the Ratio = 1, as indicated by the last value in the first line.
Please notice: Because of that rule. Lines starting with 1 * * or 2 * * should be placed at the
end of the file because they will override all lines below them.
Profile
You can set the profile type/size, or use an asterisk as a wild card.
Material
Material grade can be defined, or an asterisk as a wild card for all material grades.

Rotation
For Polybeams (Type =1):
This value corresponds to the minimum and maximum angle when the profile is rotated
around its longitudinal axis. See the image below:

Cookies help us deliver this service. By using our services, you agree to our use of Accept Decline
cookies. More information
 Tekla Structures will use a range of -180° to 180°. If you specify in the file 0° to 360°, it will
not affect the full rotation range of the polybeam. Note that Tekla Structures may
automatically change the field in the beam properties dialog box. For example, instead of
‘Top’ (+90° rotation), it may change it to ’Back’.

What degrees correspond to what Rotation setting is Tekla Structures?

CookiesInhelp us deliver
terms of thethis service.
angles Byyou
that using our services,
should you agree to our use of
put in unfold_corner_ratios.inp, theAccept
angles Decline
-180° to
cookies. More information
180° correspond to some of the Rotation settings in Tekla Structures, as follows:
 Top: -180°
Back: -90°
Below: 0°
Front: 90°
Knowing this you could set up your unfold_corner_ratios.inp file so that no matter the
orientation of a polybeam made with an angle profile (that is, “L” shape), Tekla Structures
measures the length of the polybeam along the base/heel of the angle.
1 L* * -180 -91 2 0 200000 1
1 L* * -90 -1 2 0 200000 1
1 L* * 0 89 2 0 200000 0
1 L* * 90 180 2 0 200000 0
For Plates (Type 2):
The value corresponds to the minimum and maximum thickness of the plate in mm.
The thickness is taken as the horizontal length of the extrema box around the profile. This
means that a plate profile which is 200x30 mm, could have several different ‘thicknesses’,
depending on its orientation around its longitudinal axis. For example, if it is ‘flat’, then the
thickness would be = 200 mm. If it is ‘standing’, then the thickness would be = 300 mm. See
the example in Chapter 4.1 for an example of what this means.
What happens with a polybeam with varying plate thicknesses?
Currently, polybeams with varying profiles are not supported in Tekla Structures (TS18.0
Final).
Flag
• 1 is for sharp fold. Only polybeams with straight chamfers will be affected.
• 2 is for curved bends. Only polybeams with curved chamfers will be affected.
It is important to stress the fact that in real-life situations, polybeams with certain profiles,
such as I-beams or CHS/RHS beams, are very unlikely to be manufactured using
completely straight/sharp folds. Manufacturers use minimum bending radiuses, and in order
to manufacture a straight corner, a special type of process would be required such as hot
mould casting or by cutting and welding separate beam parts.
Straight/sharp corners are usually used with plate profiles by Tekla Structures users.
Angle/Radius
• Polybeam with straight chamfers (Flag =1):
The value corresponds to the minimum and maximum angle of the sharp folds.
The angle that is measured is that between the direction of a straight section of the
polybeam, and the next section, as shown below. It is not the angle between two straight

Cookies help us deliver this service. By using our services, you agree to our use of Accept Decline
cookies. More information
 parts. See the image below.

What values should I use if I want my polybeams to always be unfolded using the
unfold_corner_ratios.inp ratio?
You should use 0 180.
Due to historical reasons, the angles that have been used are -180 to 180. This is no longer
necessary. Tekla Structures will always calculate a positive angle, no matter if the beam is
turning clockwise or anticlockwise, so only 0 to 180 is needed. Note also that Tekla

Cookies help us deliver this service. By using our services, you agree to our use of Accept Decline
cookies. More information
 Structures will not use any value larger than 180. See the image below for details.

What happens if a polybeam has several bends?

When the polybeam turns many time, Tekla Structures checks each section turn, and
unfolds it depending on whether its angle is within the values specified in the
unfold_corner_ratios.inp. For example, see the beam below, which has two sections. The
first section turns 26.75 degrees. The second section turns 63.43 degrees.

Cookies help us deliver this service. By using our services, you agree to our use of Accept Decline
cookies. More information
 Now we will show 3 situations.
Situation 1: Beam unfolds completely along inner surface (Ratio = 0).
1 HE* * -180 180 1 0 180 0
Length = 464.59 + 430.90 + 407.29 = 1302.97 mm
Situation 2: Beam unfolds completely along center line (ignores unfold_corner_ratios.inp –
see the flowchart above).
1 HE* * -180 180 1 0 25 0
Length = 500 + 559.02 + 500 = 1559.02 mm
Situation 3: Beam unfolds first part along inner surface (angle is between 0-27), but second
part along center line (angle >27).
Cookies help us deliver this service. By using our services, you agree to our use of Accept Decline
cookies.1More
HE*information
* -180 180 1 0 27 0
 Note that a common mistake would be to add up the first two inner distances, and then the
final center line distance (i.e. 464.59 + 430.90 + 500). But this would be a mistake. The
correct procedure would be to imagine the polybeam unfolding by rotating its part through
the points specified with the unfold_corner_ratio.inp. In this case, first section will be rotated
around the inner surface corner, while the second part around the centre line, as shown by
the red circles below.

If we do it in this way, the length can be easily measured measuring the unfolded straight
beam, as shown.
Polybeam with curved chamfers (Flag = 2):
The value corresponds to the minimum and maximum radius (inclusive) of curved
bends. The radius of the curved bend is the distance between the center of the circle
Cookies help us deliver this service. By using our services, you agree to our use of Accept Decline
cookies. More information
 defining the curvature and the center line of the polybeam, as shown below.

If the center line radius of the polybeam is equal to or smaller than the value in
unfold_corner_ratios.inp, then the polybeam is unfolded using accordingly; otherwise (if
larger), unfold_cornber_ratios.inp is ignored.
What happens if the polybeam has many bends?
Similarly as with polybeam with straight chamfers, when the polybeam turns many times,
Tekla Structures checks each section turn, and unfolds it depending on whether its angle is
within the values specified in unfold_corner_ratios.inp. See the example under “Polybeam
with curved chamfers (Flag = 2)”.
Ratio
This value determines how the polybeam will get unfolded, which in turn determines what its
length will be. Specifically, it determines at which depth (perpendicular to the plane of
bending/turning), Tekla Structures will unfold the beam. For example, Ratio = 0 means the
polybeam will be unfolded along its inner surface (Height = 0). Similarly, 1= outside, 0.5 =
center line, etc.
Cookies help us deliver this service. By using our services, you agree to our use of Accept Decline

See also 
cookies. More information
 Defining unfolding parameters
Length of polybeams and curved beams
Calculating polybeams
Setting the unfold_corner_ratios.inp

Tags: POLYBEAM

Quick feedback
Did you find what you were looking for? *
Yes
Partly
No

Submit

Cookies help us deliver this service. By using our services, you agree to our use of Accept Decline
cookies. More information