J.
Audet VE2AZX
Web: ve2azx.net
Revised March 2015
RETURN LOSS BRIDGE SCHEMATIC
Models 1, 2, 3
RG-174 coax
INPUT
PORT 2X 2X
100 Ω 100 Ω
1206 1206
TEST
PORT
This bridge design does not use a transformer with magnetic coupling.
Instead it uses a current balun to pickup the bridge voltage. 2X
That makes it inherently very wideband. The balun impedance 100 Ω
must be kept high over the frequency range of the bridge, 1206
since this impedance effectively appears in parallel with the unknown.
A compensating impedance is used across the internal bridge
reference termination to maintain balance at the frequency extremes RG-174 coax
of the bridge. This design is used in many commercial bridges. with Ferrite beads
With the beads placed close to the PCB, you need to measure the bridge
directivity while you move the beads away from the PCB.
First on one side, then you try the other side.
OUTPUT
One bead at a time, then two or three, until you find a spot that gives PORT
the highest directivity between 300 and 2000 MHz.
It's best to use a network analyzer setup so that you can observe the frequency
response in real time.
To attach the bead, use anything that is non metallic, such as tie wraps, cords, glue. Recommended resistor tolerance: 0.2 % giving –64 dB atten. worst case.
-50 dB bridge attenuation worst case, -60 dB average with 1 % resistors
The RG174 cable lengths should be about the same, the exact length is not critical. -70 dB bridge attenuation worst case, -80 dB average with 0.1 % resistors
Just use the length that is required as I did.
VE2AZX
TEST PORT
Cu wire
Same diam as coax
50 ohm
bridge
resistors
OUTPUT INPUT
50 ohm
50 ohm
Semi-rigid coax
termination
RETURN LOSS BRIDGE MODEL 1 100KHz – 1000 MHz VE2AZX
TEST PORT
PCB as in model 3
Plexiglass 0.112 in. thick
at the bottom to space
the two toroids from ground
Plexiglass disk
(removed)
0.112 in. thick
Note that the beads have been
RG-174 wound on VHF-UHF beads on RG-174 cable.
attached with cords to secure them
LF-HF large toroid 25 beads on each side, FT23-77
in place and optimize directivity.
FT150A-W. 6 turns
Felt pad gently holding the
toroid in place with a screw. Same enclosure
Two pads per toroid. as bridge model 3
FT150A-W ferrtie core dimensions:
OD : 1.5 in.
ID : 0.75 in.
Height : 0.5 in.
Permeability : 10 000
VE2AZX
RETURN LOSS BRIDGE MODEL 2 20KHz – 2000 MHz
Notice the coax connection
to the BNC connector.
Keep the center conductor short.
VE2AZX
RETURN LOSS BRIDGE MODEL 2 20KHz – 2000 MHz
DIRECTIVITY & TEST PORT RETURN LOSS
0
-5
-10 Insertion Loss
-15
-20
dB
-25 Test Port Ret Loss
-30
-35
-40
-45
Directivity
-50
0.01 0.1 1 10 100 1000 10000
FREQUENCY MHz
RETURN LOSS BRIDGE MODEL 2 performance tests
VE2AZX
RG-174 coax
(Internal cond. not used).
Same length as bridge
output coax. Connect to gnd
Bridge input
Bridge output
Crimped BNC
RG-174 coax
RG-174 coax LF-HF toroids VHF-UHF
beads
Use five Amidon FB43-801 beads PCB
or Fair-Rite 43 beads : 2643000801
Use two Fair-Rite #2631250202
Amidon equivalent: FB-31-0202
u = 1500 (31 material)
N connector – flat back Test Port
0.125 in / 0.25 in. and 1.0 in. long
RETURN LOSS BRIDGE MODEL 3 1 MHz to 2500 MHz VE2AZX
Selected 100 ohm 1% PCB gnd plane
1206 size bridge resistors
in parallel (0.1%) Copper foil to interconnect
PCB ground to N connector
(Foil completely covers PCB
Bridge input underneath)
RG-174 coax
RG-174 coax shield
Added 2 tapped
holes and screw
to secure PCB
on N connector
Bridge output
N connector
mounting holes
RETURN LOSS BRIDGE MODEL 3 N Connector with PCB VE2AZX
Tie-wrap OUTPUT
INPUT
Air bubble material
to hold coax cables
Silicone to hold the
Test Port ferrites in place after adjustment
by changing the ferrite position
RETURN LOSS BRIDGE MODEL 3 bridge mounted in its enclosure VE2AZX
1.00 in.
1.00 in.
Hole to secure PCB Hole to secure PCB
on N connector on N connector
See slide 5
PCB for return loss bridge models 2 and 3 VE2AZX
0 dB
RETURN LOSS BRIDGE MODEL 3
Short / Open Response
Short
Open
VE2AZX
1 MHz 100 MHz
RETURN LOSS BRIDGE MODEL 3
Short - Open Response
0 dB
VE2AZX
1 MHz 100 MHz
0 dB
RETURN LOSS BRIDGE MODEL 3
Directivity w/r to open
VE2AZX
1 MHz 100 MHz
0 dB
RETURN LOSS BRIDGE MODEL 3
Directivity w/r to short
VE2AZX
1 MHz 100 MHz
0 dB
RETURN LOSS BRIDGE MODEL 3
Return Loss at Input – 50 ohm at test port
VE2AZX
1 MHz 100 MHz
RETURN LOSS BRIDGE MODEL 3
Stocklist
QTY
10 Amidon FB43-801 Ferrite beads (u=850)
or Fair-Rite 43 SHIELD BEAD: 2643000801
u = 800 (43 material)
0.094 in / 0.296 in. and 0.297 in. Long
Use 5 per side.
4 Use Fair-Rite 31 SHIELD BEAD: 2631250202
Amidon equivalent: FB-31-0202
u = 1500 (31 material)
0.125 in / 0.25 in. and 1.0 in. long
Use two per side.
2 BNC Bulkhead Jacks, RG174 Digikey # A1813-ND
1 N type connector with flat back
1 Al Case Hammond Manufacturing # 1590B
6 Selected 100 ohm +/- 0.1 ohm 1206 SMT resistors
1 PCB
18 in. RG174 miniature coax.
Note that high freq performance critically depends on:
1- Using a small PCB, located behind the N test connector.
2- Using RG174 bulkhead BNC connectors.
3- Adjusting the location of the ferrite beads for best balance, preferably by looking at the
S21 curve from 500 to 3000 MHz.
VE2AZX
Fair-Rite 43 SHIELD BEAD: 2643000801 http://www.fair-rite.com/cgibin/catalog.pgm
u = 800 (43 material)
0.094 in / 0.296 in. and 0.297 in. long Fair-Rite authorized distributors:
Very close to Amidon FB43-801 http://www.fair-rite.com/newfair/support.htm
Use five per side
Z x5 Z Total
1 MHz 40 94
210 390
315 591
460 920
545 1025
VE2AZX
Fair-Rite 31 SHIELD BEAD: 2631250202 http://www.fair-rite.com/cgibin/catalog.pgm
u = 1500 (31 material)
0.125 in / 0.25 in. and 1.0 in. long
Use two per side
Z x2
54
140
180
276
460
480
VE2AZX
Amidon FT-23H Measured data vs Fair-Rite spec for type 31 #2631250202
