Scribd
Upload
89 views

083 RFID Door Lock Code

The document contains code for an Arduino sketch that controls access using an RFID reader. It initializes the RFID reader and pins for LEDs, buzzer, and relay. The loop scans for RFID cards, checks the UID against authorized cards, and either grants access by activating the relay for a delay or denies access by lighting the red LED and sounding the buzzer.

Uploaded by

Wahyu Restu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
89 views

083 RFID Door Lock Code

The document contains code for an Arduino sketch that controls access using an RFID reader. It initializes the RFID reader and pins for LEDs, buzzer, and relay. The loop scans for RFID cards, checks the UID against authorized cards, and either grants access by activating the relay for a delay or denies access by lighting the red LED and sounding the buzzer.

Uploaded by

Wahyu Restu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

#include <SPI.

h>
#include <MFRC522.h>

#define SS_PIN 10
#define RST_PIN 9
#define LED_G 5 //define green LED pin
#define LED_R 4 //define red LED
#define RELAY 3 //relay pin
#define BUZZER 2 //buzzer pin
#define ACCESS_DELAY 2000
#define DENIED_DELAY 500
MFRC522 mfrc522(SS_PIN, RST_PIN); // Create MFRC522 instance.

void setup()
{
Serial.begin(9600); // Initiate a serial communication
SPI.begin(); // Initiate SPI bus
mfrc522.PCD_Init(); // Initiate MFRC522
pinMode(LED_G, OUTPUT);
pinMode(LED_R, OUTPUT);
pinMode(RELAY, OUTPUT);
pinMode(BUZZER, OUTPUT);
noTone(BUZZER);
digitalWrite(RELAY, HIGH);
Serial.println("Put your card to the reader...");
Serial.println();

}
void loop()
{
// Look for new cards
if ( ! mfrc522.PICC_IsNewCardPresent())
{
return;
}
// Select one of the cards
if ( ! mfrc522.PICC_ReadCardSerial())
{
return;
}
//Show UID on serial monitor
Serial.print("UID tag :");
String content= "";
byte letter;
for (byte i = 0; i < mfrc522.uid.size; i++)
{
Serial.print(mfrc522.uid.uidByte[i] < 0x10 ? " 0" : " ");
Serial.print(mfrc522.uid.uidByte[i], HEX);
content.concat(String(mfrc522.uid.uidByte[i] < 0x10 ? " 0" : " "));
content.concat(String(mfrc522.uid.uidByte[i], HEX));
}
Serial.println();
Serial.print("Message : ");
content.toUpperCase();
if (content.substring(1) == "E4 A0 35 83") //change here the UID of the
card/cards that you want to give access
{
Serial.println("Authorized access");
Serial.println();
delay(500);
digitalWrite(RELAY, LOW);
digitalWrite(LED_G, HIGH);
delay(ACCESS_DELAY);
digitalWrite(RELAY, HIGH);
digitalWrite(LED_G, LOW);
}
else if (content.substring(1) == "73 44 CC 2E") //change here the UID of the
card/cards that you want to give access
{
Serial.println("Authorized access");
Serial.println();
delay(500);
digitalWrite(RELAY, LOW);
digitalWrite(LED_G, HIGH);
delay(ACCESS_DELAY);
digitalWrite(RELAY, HIGH);
digitalWrite(LED_G, LOW);

}
else if (content.substring(1) == "04 13 42 D2 BF 53 80") //change here the UID of
the card/cards that you want to give access
{
Serial.println("Authorized access");
Serial.println();
delay(500);
digitalWrite(RELAY, LOW);
digitalWrite(LED_G, HIGH);
delay(ACCESS_DELAY);
digitalWrite(RELAY, HIGH);
digitalWrite(LED_G, LOW);

}
else {
Serial.println(" Access denied");
digitalWrite(LED_R, HIGH);
tone(BUZZER, 300);
delay(DENIED_DELAY);
digitalWrite(LED_R, LOW);
noTone(BUZZER);
}
}

You might also like