Scribd
Upload
160 views18 pages

Chapter 3a) Retaining Walls

This document provides an overview of retaining walls and their design. It discusses the main types of conventional retaining walls, including gravity, semi-gravity, cantilever, and counterfort walls. It describes how each type is constructed and their applicable height ranges. The document also covers determining the lateral earth pressure and checking the stability of retaining walls against overturning, sliding, and bearing capacity failures. Design considerations include choosing earth pressure theories and determining reinforcement based on stability checks.

Uploaded by

lawrence
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
160 views18 pages

Chapter 3a) Retaining Walls

This document provides an overview of retaining walls and their design. It discusses the main types of conventional retaining walls, including gravity, semi-gravity, cantilever, and counterfort walls. It describes how each type is constructed and their applicable height ranges. The document also covers determining the lateral earth pressure and checking the stability of retaining walls against overturning, sliding, and bearing capacity failures. Design considerations include choosing earth pressure theories and determining reinforcement based on stability checks.

Uploaded by

lawrence
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 18

FOUNDATION ENGINEERING

(EAT 456)

CHAPTER 3
RETAINING WALLS

LECTURER:
Madam Nor Faizah Bt Bawadi
H/P No: 0125943574
Room: Muhibbah

LECTURE 3A
INTRODUCTION

• In general, retaining walls can be divided into two major


categories

(a) Conventional retaining walls


(b) Mechanically stabilized earth walls.
A. CONVENTIONAL RETAINING WALLS

Can generally be classified into four varieties:


-Gravity retaining walls
-Semi-gravity retaining walls
-Cantilever retaining walls
-Counterfort retaining walls
GRAVITY RETAINING WALLS

• Constructed with plain concrete or


stone masonry. They depend for
stability on their own weight and
any soil resting on the masonry .

• This type of construction is not


economical for high walls.
SEMI-GRAVITY RETAINING WALLS

• In many cases, a small amount of


steel may be used for the
construction of gravity walls,
thereby minimizing the size of wall
sections.

• Such walls are generally referred to


as semi-gravity walls
CANTILEVER RETAINING WALLS

• made of reinforced concrete


that consists of a thin stem and
a base slab. This type of wall is
economical to a height of about
8 m.
COUNTERFORT RETAINING WALLS

• Similar to cantilever walls. At regular intervals, however,


they have thin vertical concrete slabs known as
counterforts that tie the wall and the base slab together.
• The purpose of the counterforts is to reduce the shear and
the bending moments .
DESIGN RETAINING WALL

• There are two phases in the design of a


conventional retaining wall. First, with the lateral
earth pressure known, the structure as a whole is
checked for stability.

• The structure is examined for possible


overturning, sliding, and bearing capacity failures .
CONT…

• Second , each component of the structure is


checked for strength, and the steel reinforcement
of each component is determined.

• This chapter presents the procedures for


determining the stability of the retaining wall.
GRAVITY AND CANTILEVER WALLS

• In designing retaining walls, an engineer must


assume some of their dimensions. Called
proportioning, such assumptions allow the engineer
to check trial sections of the walls for stability.

• If the stability checks yield undesirable results ,


the sections can be changed and rechecked.
CONT…
Figure shows the general proportions of various retaining-wall components
that can be used for initial checks.
APPLICATION OF LATERAL EARTH PRESSURE
THEORIES TO DESIGN

• In the case of cantilever walls, the use of the Rankine


earth pressure theory for stability checks involves
drawing a vertical line AB through point A, located at
the edge of the heel of the base slab in figure.
• Rankine active earth pressure
equations may used to calculate the
lateral pressure on the face AB of
the wall .

• In the analysis of the wall' s stability,


the force Pa(Rankine) , the weight of
soil above the heel , and the weight
Wc of the concrete all should be
taken into consideration .

• The assumption for the


development of Rankine active
pressure along the soil face AB is
theoretically correct if the shear zone
bounded by the line AC is not
obstructed by the stem of the wall.
• A similar type of analysis may be used for gravity walls is
Coulomb's active earth pressure theory.
• If it is used, the only forces to be considered are Pa(Coulomb)
and the weight of the wall, Wc
• If Coulomb's theory is used , it will be necessary to know
the range of the wall friction angle δ ' with various types
of backfill material.

• Following are some ranges of wall friction angle for


masonry or mass concrete walls:
STABILITY OF RETAINING WALLS

A retaining wall may fail in any of the following ways:


i. It may overturn about its toe.
ii. It may slide along its base.
iii. It may fail due to the loss of bearing capacity of
the soil supporting the base.
iv. It may undergo deep-seated shear failure .
v. It may go through excessive settlement.
-END-
THANKYOU

You might also like