Scribd
Upload
391 views4 pages

Nissan Note E11 2005-2013 Accelerator Control System

The document provides instructions for removing and installing an accelerator control system. It describes: 1. Removing the accelerator pedal assembly by disconnecting the harness connector and removing mounting bolts. 2. Installing the accelerator pedal assembly by inserting a locating pin into the vehicle side and installing mounting bolts. 3. Inspecting the installation by checking that the pedal moves smoothly and securely returns to the original position. Tightening torque for the pedal assembly is also provided.

Uploaded by

Anonymous h1FnZlN
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
391 views4 pages

Nissan Note E11 2005-2013 Accelerator Control System

The document provides instructions for removing and installing an accelerator control system. It describes: 1. Removing the accelerator pedal assembly by disconnecting the harness connector and removing mounting bolts. 2. Installing the accelerator pedal assembly by inserting a locating pin into the vehicle side and installing mounting bolts. 3. Inspecting the installation by checking that the pedal moves smoothly and securely returns to the original position. Tightening torque for the pedal assembly is also provided.

Uploaded by

Anonymous h1FnZlN
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

ACCELERATOR CONTROL SYSTEM

B ENGINE

ACCELERATOR CONTROL SYSTEM


SECTION ACC ACC

E
CONTENTS
ACCELERATOR CONTROL SYSTEM ...................... 2 SERVICE DATA AND SPECIFICATIONS (SDS) ........ 3 F
Removal and Installation .......................................... 2 Tightening Torque ..................................................... 3
REMOVAL ............................................................. 2
INSTALLATION ..................................................... 2 G
INSPECTION AFTER INSTALLATION ................. 2

ACC-1
ACCELERATOR CONTROL SYSTEM

ACCELERATOR CONTROL SYSTEM PFP:18005

Removal and Installation BBS003Z9

PBIC1506E

Accelerator pedal stopper


1. Accelerator pedal assembly 2.
(Under floor carpet)

REMOVAL
1. Remove harness connector.
2. Remove mounting bolts, and remove accelerator assembly.
CAUTION:
● Do not disassemble accelerator pedal assembly and remove sensors.
● Handle them carefully without subjecting them to impacts such as dropping.
● Be careful not to get it wet.
3. Fold the floor carpet and remove accelerator pedal stopper.
● Remove pedal stopper by turning it counterclockwise with fingers.

INSTALLATION
Install in the reverse order of removal. be careful of the following:
● Insert locating pin into vehicle side to position accelerator pedal assembly. Install mounting bolt to acceler-
ator pedal assembly.
● Align the stud bolt on the floor with the thread hole to insert accelerator pedal stopper until it contacts the
face.
INSPECTION AFTER INSTALLATION
● Check that the accelerator pedal moves smoothly within the whole operation range.
● Check that the accelerator pedal securely returns to the original position.
● For the electrical inspection of the accelerator pedal assembly, refer to EC-409, "DTC P2138 APP SEN-
SOR" (CR WITH EURO-OBD), EC-725, "DTC P2138 APP SENSOR" (CR WITHOUT EURO-OBD) and
EC-1197, "DTC P2138 APP SENSOR" (HR WITH EURO-OBD), EC-1517, "DTC P2138 APP SENSOR"
(HR WITHOUT EURO-OBD) or “Interpretation”, “DIESEL INJECTION” in EC section(K9K).
● When accelerator electrical connector is disconnected, perform EC-69, "Accelerator Pedal Released
Position Learning" (CR WITH EURO-OBD), EC-486, "Accelerator Pedal Released Position Learning"
(CR WITHOUT EURO-OBD) and EC-857, "Accelerator Pedal Released Position Learning" (HR WITH
EURO-OBD), EC-1278, "Accelerator Pedal Released Position Learning" (HR WITHOUT EURO-OBD).

ACC-2
SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS) PFP:00030


A
Tightening Torque BBS003ZA

Unit: N·m (kg-m, in-lb)


Accelerator pedal assembly 4.3 - 5.9 (0.44 - 0.60, 38 - 52) ACC

ACC-3
SERVICE DATA AND SPECIFICATIONS (SDS)

ACC-4

You might also like