Scribd
Upload
310 views

HF5111B Test Manual

HF5111B Test Manual - Serial Device Server

Uploaded by

lmpombo
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
310 views

HF5111B Test Manual

HF5111B Test Manual - Serial Device Server

Uploaded by

lmpombo
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 22

User Manual and Test Guide

HF5111B

Operation Guide

http://www.iotworkshop.com 1 Copyright © 2013 . All rights reserved


Content

1. SERIAL SERVER CONNECTION ..................................................................................... 3

1. 1 HF5111B Connection .............................................................................................. 3

2. Serial Settings ..................................................................................................................... 4

2.1. SecureCRT Serial Tool SecureCRT ........................................................................ 4

2.2. Configure Serial Parameter ................................................................................... 4

3. HF5111BNETWORK CREATION .................................................................................... 6

3.1. TCP/IP Princple and Test Purpose ........................................................................ 6

3.2. Auto-IP Networking ................................................................................................ 6

3.3. Auto-IP TCP Server Test ........................................................................................ 10

3.4. Networking by Router .......................................................................................... 15

Version List：

2017-10-16 First Draft

http://www.iotworkshop.com 2 Copyright © 2013 . All rights reserved


1. SERIAL SERVER CONNECTION
1. 1 HF5111B Connection
HF5111B connect with PC by Ethernet cable or router. Only retain network
connect and forbid extra network connection. After the Link light on , then open
IOTService. As a result, the IP address of HF5111B will be displayed. When HF5111B
use Auto-IP function, the Ethernet interface is 169.254.173.207 .If the configuration
product is connected to the PC through a router, the IP address is assigned by the
router or can be set statically.

http://www.iotworkshop.com 3 Copyright © 2013 . All rights reserved


2. SERIAL SETTINGS
2.1. SecureCRT Serial Tool SecureCRT
Download adddress：
http://gb.hi-flying.com/download_detail_dc/downloadsId=22.html

Decompress file and find executable program, , then open.

Click quick start button to create connection.

2.2. Configure Serial Parameter


Protocol：Serial
Port: Actual connection port(search by “My PC”->”Device

Manager”->”Port(COM and LPT)”. As figure: )


Baud Rate：115200
Data Bits：8
Parity Check Bit：None
Stop Bit：1
Flow Control： None（Please tick off “√”before RTS/CTS）

http://www.iotworkshop.com 4 Copyright © 2013 . All rights reserved


Notes: HF5111B the default serial data is as above and user can modify device
working parameter by IOTService.

http://www.iotworkshop.com 5 Copyright © 2013 . All rights reserved


3. HF5111BNETWORK CREATION
3.1. TCP/IP Principle and Test Purpose
Principle: Network use physical data link to bulid connection among each isolated
station or host to combine data link. As a result, it achieves resource share and
communication. It is the most important communication protocol in the process of
network communication. HF5111B adopts TCP/IP protocol which contain TCP and
UDP etc. IP address and port number are two important parameter during
generating connection. First, server should make sure IP address and port number.
Then client binds the same IP address and port with server to generate connection
successfully.
Test purpose:
1. PC connects to HF5111B by serial cable. Open SecureCRT to verify if
serial port can send and receive data normally.
2. HF5111Bcan connect to PC through the network when it works under
STA mode. And it can also connect to PC in AP mode. After open tcpudpdbg
tool, PC is recognized as client connected with serial side. Above two software
can be used to verify data flow between HF5111B and PC.
In following test, “TCP Server Test”-HF5111B as server and PC as client.”
TCP Client Local Test”-HF5111B as client and PC as server.

3.2. Auto-IP Networking


Device can directly connect to PC by Ethernet cable and module will use its default
IP for PC directly visit or data transfer communication(approximately 15 seconds
until PC use 169.254.XXX.XXX). For example, below module IP:
169.254.173.207(normally fixed IP, if conflicts, it will change to another IP
automatically)

http://www.iotworkshop.com 6 Copyright © 2013 . All rights reserved


Step 1: Ethernet cable connects RJ45 ports between device and PC. Open
IOTService and it will achieve device information automatically. Figure is as below:

Step 2：According to IP address above, it can be configured parameter by website.


Username and password are both admin as default. As below figure:

http://www.iotworkshop.com 7 Copyright © 2013 . All rights reserved


Step 3： HF5111B can connect PC to simulate serial signal from lower MCU by
RS232. The connection method of RS485/422 can refer to chapter 2.3 and 2.4 from
HF5111B user manual.
Step 4：Open serial configure tool, SecureCRT is recommended(Others is ok but not
convenient). Following test is under SecureCRT and serial parameter can refer to
Chapter 2.1 and 2.2. The default state is transparent mode when open SecureCRT. If
enter into command mode, it needs input three”+”sequently. Afterwards, screen
appear “EPORT>”. It can use CLI command to set the state of HF5111Bafter
entering into command mode. Specific operation method can refer to
HF5111Buser manual.

http://www.iotworkshop.com 8 Copyright © 2013 . All rights reserved


http://www.iotworkshop.com 9 Copyright © 2013 . All rights reserved
3.3. Auto-IP TCP Server Test
Step 1：Open TCP&UDP test tool and generate TCP connection as following
process.
 Product has already created a TCP Server(port 8899) for use.
 TCP&UDP test tool can be downloaded from official website:
http://gb.hi-flying.com/download_detail_dc/downloadsId=54.html
 DestIP：IP address of product, this address can be found by IOTService tool.
 Port：TCP Server port number,8899 default which can be modified by
IOTService

http://www.iotworkshop.com 10 Copyright © 2013 . All rights reserved


http://www.iotworkshop.com 11 Copyright © 2013 . All rights reserved
Step 2：Click Connect to build TCP connection
 After successful generation, left side turn to green arrow, yellow if fails.

http://www.iotworkshop.com 12 Copyright © 2013 . All rights reserved


Step 3：Open serial tool according to following parameter(115200 baud rate as
default)

Step 4：Make sure if serial tool is CMD mode. Input “Exit”to exit CMD mode and
enter into transparent mode(which is default)

Step 5：Mutual data transmission between TCP and serial port.

http://www.iotworkshop.com 13 Copyright © 2013 . All rights reserved


http://www.iotworkshop.com 14 Copyright © 2013 . All rights reserved
3.4. Networking by Router
After HF5111B has created network connection with router, any terminal can
communicate with 5111B. As the figure shows, IP address will automatically change
to the same IP segment 192.168.1.X with router.

RS232/RS485

IP：192.168.1.101

Server
Server PLC Device

Ethernet

WWW. Network Cloud

IP：192.168.1.1
on
necti
s Con
s
Wirele

Laptop

IP：192.168.1.6

Step 1：If users want understand real-time IP address of 5111B, IOTService can be
opened for searching or serial query.

http://www.iotworkshop.com 15 Copyright © 2013 . All rights reserved


Step 2：Product acquires IP address from upper router. If user need to modify it to
static IP address, it can be configured by IOTService(as below). Restart after
configured.

http://www.iotworkshop.com 16 Copyright © 2013 . All rights reserved


Step 3：Configure relative serial parameter with MCU.

http://www.iotworkshop.com 17 Copyright © 2013 . All rights reserved


Step 4：Retain local connection and forbid extra network connection.

http://www.iotworkshop.com 18 Copyright © 2013 . All rights reserved


Step 5: Open TCP&UDP tool and create a server.(IP is PC local address, or default.
Port is selected randomly as long as not occupied by extra network)

http://www.iotworkshop.com 19 Copyright © 2013 . All rights reserved


Step 6: Default parameter of socket is netp(name), Tcp Server, 8899(port). User can
create a new socket according to demand.

http://www.iotworkshop.com 20 Copyright © 2013 . All rights reserved


Step 7：After successfully created socket, restart product and open SecureCRT to
simulate data transmission between serial port and terminal.

http://www.iotworkshop.com 21 Copyright © 2013 . All rights reserved


http://www.iotworkshop.com 22 Copyright © 2013 . All rights reserved

You might also like