Scribd
Upload
172 views

Tank Data Sheet

This document provides vessel design specifications including tag number, working volume, diameter, design pressures and temperatures for the vessel and heat transfer jacket, configuration details for the vessel heads and shell, material specifications for internals and externals, and requirements for supports, fittings, options, and factory acceptance testing. Key details include the vessel working volume, cylindrical shell design, ASME flanged and dished top and bottom heads, design for a heat transfer jacket, and hydrotesting and inspection requirements.

Uploaded by

anon_256154377
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
172 views

Tank Data Sheet

This document provides vessel design specifications including tag number, working volume, diameter, design pressures and temperatures for the vessel and heat transfer jacket, configuration details for the vessel heads and shell, material specifications for internals and externals, and requirements for supports, fittings, options, and factory acceptance testing. Key details include the vessel working volume, cylindrical shell design, ASME flanged and dished top and bottom heads, design for a heat transfer jacket, and hydrotesting and inspection requirements.

Uploaded by

anon_256154377
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 5

10-Feb-01

Vessel Data Sheet:

Tag No.:

Working Volume: (1) Gallons/Liters


Diameter:
Tangent to tangent length:

Vessel Design Data:


Design Pressure: PSIG
Design Vacuum: PSIG
Design Temperature: ºF/ºC

HX Jacket Design Data:


Design Pressure: PSIG
Design Vacuum: PSIG
Design Temperature: (4) ºF/ºC

Configuration:
Top Head Type:
ASME Flanged & Dished:
2:1 Elliptical:(2)
Bottom Head Type:
ASME Flanged & Dished:
2:1 Elliptical:(2)
Toriconical: (3)
Shell:
Cylindrical
External Stiffening/Vacuum rings allowed?: Y/N

Heat Transfer Jacket:


Jacket coverage:
Bottom only
Side only
Side and bottom
Jacket type:
Dimpled:
Half-pipe:
Conventional:
Vent fittings:
Drain fittings:
Material type:
Internals:
Heat Transfer jacket:
Sheathing:
Reinforcing pads on OD:
Stiffening/Vacuum rings:
Other externals:
Insulation type:
Fiberglass:
Mineral Wool:
Rock wool:
Cellular glass:
Gasket type:
Teflon
Viton
EPDM
Silicone

Internal Finish:
Material finish:
Mill finish: HRAP for plate - 3/16" and thicker
2B mill finish for sheet - 7 Ga. and thinner
Mechanically polished:
Specify Ra to which ID must be polished
25-35 Ra = 180 grit = #4 finish
18-20 Ra = 240 grit
10-15 Ra = 320 grit
Weld finish:
For mill finish tanks:
As welded and cleaned
Ground smooth not flush
Ground smooth and flush to _____ Ra
For Mechanically polished tanks:
Weld finish is always flush with parent metal
and finished to same Ra as material.
Electropolished:

External Finish:
Material: Mill finish HRAP for plate - 3/16" and thicker
2B mill finish for sheet - 7 Ga. and thinner
Mechanically polished:
Specify Ra to which OD must be polished
25-35 Ra = 180 grit = #4 finish
18-20 Ra = 240 grit
Weld finish:
For all tanks OD:
As welded and cleaned
Ground smooth not flush
Ground smooth and flush to _____ Ra
Supports:
Number of supports:
Desired outlet height:
Type of supports:
Legs with flat pad feet.
Legs with flat pad feet drilled for load cells.
Legs with casters:
Two (2) Swivel w/brakes & two (2) rigid
Two (2) Swivel w/locks & brakes & two (2) rigid
Four (4) swivel with locks and brakes
Type of Caster:
SS pharmaceutical
Autoclavable:
Side lugs

Mixer required:
Type:
Top Entering:
Center mounted with baffles.
Angular offset.
Mounting:
Stud pad
Flange
Bottom entering Magnetically coupled.
Motor: Standard Duty
Explosion proof
Voltage: 120/1
230/3
480/3
Fittings:
Flanges:
150#, 300#
RFSO - Raised face slip-on flanges.
RFWN - Raised face weld neck flanges.
LJSE - Lap joint stub ends with back-up flanges.
Back-up flanges
304 SS
316L SS
Sanitary Clamp ferrules.
Stud Pads.
Flush bottom outlet valves.
Flush side sampling valves.
"Ingold" fittings.
Flush mount level shells.
Themometer wells.
Manways:
w/spring assist.
Hand holes:
Options:
Riboflavin spray ball testing.
Passivation.
Vortex breaker over outlet:
Vertical flat single plate.
Vertical flat cross plate.
Disk style.

Accessories:
Lights
Sight glasses
Rupture disks
VFDs for motors

FAT:
Hydrotesting:
Riboflavin testing:
Drainage testing:
Agitator run test:

NOTES:
(1) - Usually working volume is about 6" to 8" below top tangent line.
(2) - Usually less expensive when design pressures are >=100 PSIG.
(3) - Must specify included angle.
(4) - Always same as tank design temperature.

You might also like