Scribd
Upload
124 views6 pages

WWW - Manaresults.Co - In: II B. Tech II Semester Regular Examinations, April/May - 2016 Machine Drawing

This document contains four machine drawing question papers with multiple choice questions related to drawing various mechanical components and assemblies. Each paper contains three questions in Part A asking to draw specific joints, keys, bearings etc. along with dimensions. Part B of each paper asks to assemble components shown in figures and draw sectional and side views of the assembled mechanism or device. The questions test skills in machine drawing, assembly drawing and dimensioning of mechanical parts and systems.

Uploaded by

krisbhaskar22-1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
124 views6 pages

WWW - Manaresults.Co - In: II B. Tech II Semester Regular Examinations, April/May - 2016 Machine Drawing

This document contains four machine drawing question papers with multiple choice questions related to drawing various mechanical components and assemblies. Each paper contains three questions in Part A asking to draw specific joints, keys, bearings etc. along with dimensions. Part B of each paper asks to assemble components shown in figures and draw sectional and side views of the assembled mechanism or device. The questions test skills in machine drawing, assembly drawing and dimensioning of mechanical parts and systems.

Uploaded by

krisbhaskar22-1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Code No: RT22035 R13 SET - 1

II B. Tech II Semester Regular Examinations, April/May – 2016


MACHINE DRAWING
(Com. to ME, AME, MM)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answer TWO question from Part-A
3. Part-B is compulsory
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

PART –A
1. Represent two views of hexagonal nut and square nut with proportions and (11M)
take the diameter of the bolt as 30 mm
2. Draw a proportionate diagram of Double rivetted double strap chain type butt (11M)
joint two connect plate of 20 mm size.
3. Draw two views of a Food step bearing for a shaft 100 mm diameter (11M)
PART –B
4. Draw the following views at assembly of eccentric mechanism as shown in (48M)
Figure 1.
a) Sectional front view. b) Right side view

WWW.MANARESULTS.CO.IN
1 of 1
|''|'''||''||'''||||
Code No: RT22035 R13 SET - 2

II B. Tech II Semester Regular Examinations, April/May – 2016


MACHINE DRAWING
(Com. to ME, AME, MM)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answer TWO question from Part-A
3. Part-B is compulsory
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

PART –A
1. a) Sketch the following thread profiles for a nominal diameter of 20 mm and (5M)
pitch 2 mm
i) Worm thread ii) ACME thread
b) Sketch neatly, giving proportionate dimensions, the eye foundation bolt of (6M)
diameter 25 mm?
2. Draw two views of a Single strap butt joint of two rows zig – zag to connect (11M)
two plates of 9 mm thick?
3. Draw gib and cotter joint suitable for joining 40 mm square rods? (11M)
PART -B
4. Figure 1 gives the part drawings of Plummer block. Assemble all the parts and (48M)
draw the following assembled views.

a) Sectional front view b) Top view.

WWW.MANARESULTS.CO.IN
1 of 1
|''|'''||''||'''||||
Code No: RT22035 R13 SET - 3

II B. Tech II Semester Regular Examinations, April/May – 2016


MACHINE DRAWING
(Com. to ME, AME, MM)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answer TWO question from Part-A
3. Part-B is compulsory
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

PART –A
1. a) Two views of a taper sunk key positioned in a shaft of diameter 25mm and hub (6M)
of diameter 50mm and mark dimensions on it.
b) Sketch a feather key with proportions (5M)

2. Draw a proportionate diagram of Socket and spigot pipe joint to connect two (11M)
pipes of φ 50mm

3. Draw a proportionate diagram of Journal bearing for a shaft of φ 40mm. (11M)

1 of 2

WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
Code No: RT22035 R13 SET - 3

PART -B
4. Figure 1 gives the detailed drawings of a screw jack. Assemble all the parts and (48M)
draw the following assembled views.

a) Sectional front view b) Top view

2 of 2
WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
Code No: RT22035 R13 SET - 4

II B. Tech II Semester Regular Examinations, April/May – 2016


MACHINE DRAWING
(Com. to ME, AME, MM)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answer TWO question from Part-A
3. Part-B is compulsory
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

PART –A
1. Draw a proportionate diagram of Single rivetted lap joint to connect two plates (11M)
of 5mm thick.

2. Draw a proportionate diagram of pivot bearing for a shaft of φ 30mm (11M)

3. Draw a proportionate diagram of Sleeve type cotter joint to connect two shafts of (11M)
φ30mm.

1 of 2

WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
Code No: RT22035 R13 SET - 4

PART -B
4. Assemble the parts of a spring loaded relief valve, shown in figure and draw the (48M)
following views:
a) Sectional view from the front
b) View from the right

WWW.MANARESULTS.CO.IN
2 of 2

|''|'''||''||'''||||

You might also like