Scribd
Upload
80 views

Inspection and Test Procedures For Metal

The document provides inspection and test procedures for metal-enclosed busways. It outlines visual and mechanical inspection steps including comparing nameplate data, inspecting physical condition, connections, and bolted connections. It also describes electrical tests such as measuring insulation resistance and performing dielectric withstand tests. Test values are provided for comparing bolted connection resistance, insulation resistance, and dielectric withstand voltages.

Uploaded by

Hafidz Bandung
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
80 views

Inspection and Test Procedures For Metal

The document provides inspection and test procedures for metal-enclosed busways. It outlines visual and mechanical inspection steps including comparing nameplate data, inspecting physical condition, connections, and bolted connections. It also describes electrical tests such as measuring insulation resistance and performing dielectric withstand tests. Test values are provided for comparing bolted connection resistance, insulation resistance, and dielectric withstand voltages.

Uploaded by

Hafidz Bandung
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Inspection and Test Procedures for Metal-Enclosed

Busways
1. Visual and Mechanical Inspection

1. Compare equipment nameplate datawith drawings and specifications.


2. Inspect physical and mechanical condition of busway system
3. Inspect anchorage, alignment, and grounding.
4. Verify correct connection in accordance with single-line diagram.
5. Inspect bolted electrical connections for high resistance using one or more of the
following methods:
 Use of a low-resistance ohmmeter in accordance with Section 2 (Electrical
Tests).
 Verify tightness of accessible bolted electrical connections and bus joints by
calibrated torque-wrench method in accordance with manufacturer’s published
data or Table 100.12 below.
 Perform thermographic survey
(NOTE: Remove all necessary covers prior to thermographic inspection. Use
appropriate caution, safety devices, and personal protective equipment.)
6. Confirm physical orientation in accordance with manufacturer’s labels to insure
adequate cooling.
7. Examine outdoor busway for removal of “weep-hole” plugs, if applicable, and the
correct installation of joint shield.

2. Electrical Tests

1. Perform resistance measurements through bolted connections and busjoints with a


low-resistance ohmmeter, if applicable, in accordance with Section 1 (Visual and
Mechanical Inspection).
2. Measure insulation resistance of each busway, phase-to-phase and phase-to-
ground for one minute, in accordance with Table 100.1 below.
3. Perform a dielectric withstand voltage test on each busway, phase-to-ground with
phases not under test grounded, in accordance with manufacturer’s published data.
In the absence of manufacturer’s published data, use Table 100.17.
Where no dc test value is shown in Table 100.17, ac value shall be used. The test
voltage shall be applied for one minute.
4. Perform a contact-resistance test on each connection point of uninsulated busway.
On insulated busway, measure resistance of assembled busway sections and
compare values with adjacent phases.
5. Perform phasing test on each busway tie section energized by separate sources.
Tests must be performed from their permanent sources.
6. Verify operation of busway space heaters.
3. Test Values

3.1 Test Values – Visual and Mechanical


1. Compare bolted connection resistance values to values of similar connections.
Investigate values which deviate from those of similar bolted connections by more
than 50 percent of the lowest value. (7.4.1.5.1)
2. Bolt-torque levels should be in accordance withmanufacturer’s published data. In
the absence of manufacturer’s published data, use Table 100.12. (7.4.1.5.2)
3. Results of the thermographic survey shall be in accordance with Section 9.
(7.4.1.5.3)

3.2 Test Values – Electrical

1. Compare bolted connection resistance values to values of similar connections.


Investigate values which deviate from those of similar bolted connections by more
than 50 percent of the lowest value.
2. Insulation-resistance test voltages and resistance values shall be in accordance
with manufacturer’s published. In the absence of manufacturer’spublished data,
use Table 100.1.
Minimum resistance values are for a nominal 1000-foot busway run. Use the following
formula to convert the measured resistance value to the 1000-foot nominal value:

Converted values of insulation resistance less than those in Table 100.1 or


manufacturer’s minimum should be investigated. Dielectric withstand voltage tests
shall not proceed until insulation-resistance levels are raised above minimum values.
3. If no evidence of distress or insulation failure is observed by the end of the total
time of voltage application during the dielectric withstand test, the test specimen is
considered to have passed the test.
4. Microhm or dc millivolt drop values shall not exceed the high levels of the normal
range as indicated in the manufacturer’s published data.
If manufacturer’s published data is not available, investigate values which deviate from
those of similar bus connections and sections by more than 50 percent of the lowest
value.

5. Phasing test results shall indicate the phase relationships are in accordance with
system design.
6. Heaters shall be operational.
TABLE 100.12

US Standard Fasteners – Bolt-Torque Values for Electrical


Connections
a. Consult manufacturer for equipment supplied with metric fasteners.
b. This table is based on bronze alloy bolts having a minimum tensile strength of
70,000 pounds per square inch.
c. This table is based on aluminum alloy bolts having a minimum tensile strength of
55,000 pounds per square inch.
d. This table is to be used for the following hardware types:
 Bolts, cap screws, nuts, flat washers, locknuts (18–8 alloy)
 Belleville washers (302 alloy).
TABLE 100.1

Insulation Resistance Test Values Electrical Apparatus and Systems

TABLE 100.17

Dielectric Withstand Test Voltages for Metal-Enclosed Bus

You might also like