Scribd
Upload
204 views3 pages

Upper Basement: Waffle Slab Design

This document summarizes the design of a waffle slab for an upper basement. Key specifications include a total load of 10.125 KN/m^2, spans of 8.45m and 8.1m, and a slab thickness of 90mm. Reinforcement is designed at supports, midspans, and for shear. At supports, 0.045% tension steel is required at the top and 0.001% compression steel at the bottom. At midspans, 0.15557% steel is designed to resist bending. Shear capacity is checked to be 0.578121 N/mm^2, less than the allowable of 0.72 N/mm^2. Deflection is checked using

Uploaded by

Vinay Kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
204 views3 pages

Upper Basement: Waffle Slab Design

This document summarizes the design of a waffle slab for an upper basement. Key specifications include a total load of 10.125 KN/m^2, spans of 8.45m and 8.1m, and a slab thickness of 90mm. Reinforcement is designed at supports, midspans, and for shear. At supports, 0.045% tension steel is required at the top and 0.001% compression steel at the bottom. At midspans, 0.15557% steel is designed to resist bending. Shear capacity is checked to be 0.578121 N/mm^2, less than the allowable of 0.72 N/mm^2. Deflection is checked using

Uploaded by

Vinay Kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

WAFFLE SLAB DESIGN UPPER BASEMENT

DEAD LOAD 3.125 KN/M^2


PARKING 5 KN/M^2
LIVE LOAD 2 KN/M^2
TOTAL 10.125

LONG SPAN 8.45 M

SHORT SPAN 8.1 M

RIB SPACING LONG 0.9 M

RIB SPACING SHORT 0.9 M

RIB DEPTH 325 MM

RIB WIDTH BOTTOM 150 MM


RIB WIDTH TOP 250 MM
DEPTH OF SLAB 90 MM

UDL 10.125 KN/M^2

FCK 25 N/MM^2

FY 500 N/MM^2

DIMENSION CHECK AS PER IS 456

RIB WIDTH 150 > 65MM

RIB SPACING 0.9 < 1.5M

COVER TO REINFORCEMENT 20 MM

EFFECTIVE DEPTH 150-20 305 MM

SLAB DESIGNED AS TWO WAY SLAB

INTRIOR PANEL

COEFF SHORT SPAN LONG SPAN

NEGETIVE 0.032 0.032

POSITIVE 0.024 0.024

TWO ADJESANT PANEL CONTINEOUS

LX/LY 3.9/3.6 1.04321

COEFF SHORT SPAN LONG SPAN

NEGETIVE 0.052 0.047

POSITIVE 0.039 0.035

MAXIMUM NEGETIVE MOMENT 0.052*WLx^2 0.052*9.125*8.1^2 34.54367 KNM/M

MAXIUM POSITIVE MOMENT 0.039*WLx^2 0.039*9.125*8.1^2 25.90775 KNM/M

MAXIMUM MOMENT ONE RIB HAS TO CARRY =


MOMENT PER METRE*RIB SPACING

MAXIMUM NEGETIVE MOMENT 1.2*34.54 - 41.4524 KNM

MAXIUM POSITIVE MOMENT 1.2*25.90 + 31.0893 KNM

DESIGN OF SECTION AT SUPPORT


Only the rib will be effective .Compression steel is provided
at the bottom and additional tension steel at top.

Mu - 41.4524 KNM
d 305 MM
b 150 MM
d'/d 20/305 0.065574
Mu/b*d^2 63.5*10^6/100*305^2 2.970699

REFER TABLE 55OF sp16

TENSION STEEL AT TOP 0.045 %

Compression steel at bottom 0.001 %

Ast 0.045*150*305/100 20.5875 MM^2

PROVIDE 1 NO 16 DIA BARS 200.96 MM^2


2 NO 12 DIA BARS 226.08
Asc 0.001*150*305/100 0.4575 MM^2

PROVIDE 2 NO 12 DIA BARS 226.08 MM^2

DESIGN OF SECTION AT MID SPAN

section acts with top concrete


in compression ( thickness of topping 90mm)
Ast Mu/0.87fy(d-Df/2) 28*10^6/(0.87*500*(305-90/2) 274.8833 MM^2

PROVIDE 2 NO 12 DIA BARS 226.08 MM^2


1 NO 16 DIA BARS 200.96 MM^2 427.04
Percentage of steel provided 427*100/900*305 0.15557 %

minimum steel for T-Beam = 0.17%

Miimum steel Ast 0.17*305*250/100 129.625 MM^2

PROVIDE 1 NO 16 DIA BARS 200.96 MM^2


2 NO 12 DIA BARS 226.08 MM^2 427.04
CHECK FOR SHEAR

MINIMUM SHEAR 0.43W*LX 0.43*9.125*8.1^2 35.26538 KN/M

VS= SHEAR X RIB SPACING 35.26*0.9 31.73884 KN

BREADTH OF RIB 200 MM

V 31.73*10^3/200*305 0.578121 N/MM^2

ALLOWABLE SHEAR FOR 0.15% STEEL 0.36 N/mm^2

ENHANCED SHEAR 2D*Tc/Av 0.72 N/mm^2

CHECK FOR DEFLECTION

BY EMPHIRICAL PROCEDURE FOR T BEAM

DEPTH OF BEAM 325 MM

L/D RATIO 8100/325 24.92308

BASIC L/D RATIO (CONTINEOUS SPAN) = 26 SATISFACTORY

DETAIL OF STEEL

Special care shall be aken to provide


necessary corner steel
5 KN/M^2

You might also like