TI00444C/07/EN/17.

13 Products Solutions Services

71241741

Technical Information
Liquiline CM442/CM444/CM448
Multiparameter transmitter with a maximum of eight
measuring channels based on digital Memosens
technology

Extensible multiparameter controller for monitoring and controlling processes

in industry and the environmental sector
Application Your benefits
– Possible to connect up to 8 Memosens sensors • Maximum process safety thanks to:
– Mathematic functions calculate new measured values – Simple and transparent menu guidance via a graphic
– Max. 8 analog outputs 0/4 to 20 mA display
– Digital fieldbuses (HART, PROFIBUS, Modbus, Ethernet/IP) – Standardized operating concept across all devices from
and integrated web server the Liquiline, sampler and analyzer platform
– Selectable: cleaning function, controller and alarm relay • Fast commissioning thanks to:
– Optional digital inputs/outputs or current inputs for signal – Memosens: lab-calibrated sensors & hot plug-and-play
transmission from other devices – Preconfigured Liquiline transmitter
– Easy to expand and adapt system to meet new
The rugged non-Ex plastic version is tailored to:
requirements
• Water and wastewater
• Minimum inventory:
• Power stations
– Cross-platform, modular concept (e.g. identical modules
• Chemical industry
irrespective of parameters)
• Other industrial applications
– Integration into Fieldcare and W@M facilitates effective
asset management
 Liquiline CM442/CM444/CM448

Table of contents

Function and system design . . . . . . . . . . . . . . . . . . . . . .4 Digital outputs, passive . . . . . . . . . . . . . . . . . . . . . . . . 21

Measuring system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Electrical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Application example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PFM function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Auxiliary voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Test voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Equipment architecture . . . . . . . . . . . . . . . . . . . . . . . . . .6
Cable specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Slot and port assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Order of the modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Basic rule for hardware upgrades . . . . . . . . . . . . . . . . . . . . . . . . 6 Current outputs, active . . . . . . . . . . . . . . . . . . . . . . . . . 21
Determining the hardware delivery status . . . . . . . . . . . . . . . . . 7 Span . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Terminal diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Signal characteristic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Device configuration CM442 using the example of a Electrical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
CM442-**M1A1F0* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Cable specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Function diagram CM442 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Device configuration using the example of a
Relay outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
CM444-**M42A1FA* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Electrical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Function diagram CM444 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cable specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Device configuration using the example of a
CM448-**26A1* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Function diagram CM448 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Protocol-specific data . . . . . . . . . . . . . . . . . . . . . . . . . . 23
HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Communication and data processing. . . . . . . . . . . . . 14 PROFIBUS DP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Modbus RS485 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Modbus TCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Dependability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 EtherNet/IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Web server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Maintainability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Fieldbus connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Measured variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Measuring ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Types of input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Cable entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Input signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Cable specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cable specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Connecting optional modules . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Digital inputs, passive . . . . . . . . . . . . . . . . . . . . . . . . . 19 Protective ground connection . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Sensor connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Electrical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Span . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Nominal input current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Performance characteristics . . . . . . . . . . . . . . . . . . . . 32
PFM function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Response time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Test voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Reference temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Cable specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Maximum measured error of sensor inputs . . . . . . . . . . . . . . . 32
Measured error for current inputs and outputs . . . . . . . . . . . . 32
Current input, passive . . . . . . . . . . . . . . . . . . . . . . . . . 19 Frequency tolerance of digital inputs and outputs . . . . . . . . . 32
Resolution of current inputs and outputs . . . . . . . . . . . . . . . . . 32
Span . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Repeatability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Signal characteristic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Internal resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Test voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Mounting plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Weather protection cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Signal on alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Linearization/transmission behavior . . . . . . . . . . . . . . . . . . . . 21

2 Endress+Hauser
 Liquiline CM442/CM444/CM448

Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Ambient temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Vibration resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Electromagnetic compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Electrical safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Pollution degree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Pressure compensation to environment . . . . . . . . . . . . . . . . . . 36

Mechanical construction . . . . . . . . . . . . . . . . . . . . . . . 36
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Operability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Operating concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Local operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Language packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Product structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Certificates and approvals . . . . . . . . . . . . . . . . . . . . . . 41

4 mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
cCSAus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
FM/CSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
MCERTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Weather protection cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Post mounting kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Measuring cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Additional functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Other accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

3 Endress+Hauser
 Liquiline CM442/CM444/CM448

Function and system design

Measuring system The following overview shows examples of the design and layout of a measuring system.
Other sensors and assemblies can be ordered for conditions specific to your application
(--> www.endress.com/products).

Measuring point pH value or ORP

A complete measuring system consists of: pH measurement in drinking water
• Liquiline transmitter • Retractable assembly Cleanfit
• Sensors with Memosens technology CPA471
• Assemblies to suit the sensors used • Sensor Orbisint CPS11D
• Post or rail mounting (optional) • Measuring cable CYK10
• Weather protection cover (optional) --> graphic
ORP in drinking water
• Immersion assembly Dipfit
CYA112
1 2 • Sensor Orbisint CPS12D
• Measuring cable CYK10
a0012413

Conductivity
Inductive conductivity
measurement in wastewater
treatment
• Sensor Indumax CLS50D
with fixed cable
Conductive conductivity
measurement in power plant
cooling water
• Sensor Condumax CLS15D

a0012412

Oxygen
Oxygen in aeration basins
• Immersion assembly Dipfit
5 4 3 CYA112
• Holder CYH112
a0012411
• Sensor
Measuring system (e.g. two-channel device)
– COS61D (optical)
1 Liquiline with fixed cable,
2 Weather protection cover CYY101 (optional) – COS51D (amperometric)
3, 5 Sensor cable CYK10 or fixed cable (digital fixed cable
sensors with Memosens protocol) cable CYK10
4 Power supply cable (to be provided by the customer, not Figure: CYA112 with COS61D
part of the scope of supply)
a0012415

Nitrate and SAC Turbidity and interface

Nitrate in wastewater Turbidity in industrial water
• Sensor CAS51D-**A2 with fixed • Sensor Turbimax CUS51D
cable with fixed cable
• Assembly CYA112 • Assembly Flowfit CUA250
• Holder CYH112 • Spray head CUR3 (optional)
SAC in the wastewater treatment Interface in the primary clarifier
outlet • Sensor Turbimax CUS71D
• Sensor CAS51D-**2C2 with • Assembly CYA112
fixed cable • Holder CYH112
• Assembly CYA112
Figure: CUA250 with CUS51D
• Holder CYH112
a0012787 a0012788

Chlorine Ion selective electrodes

Chlorine (and pH) in drinking Ammonium and nitrate
water measurement in the aeration basin
• Sensor CCS142D • Sensor CAS40D with fixed cable
• Sensor CPS11D • Holder CYH112
• Measuring cable CYK10
• Flow assembly CCA250

a0015030 a0015077

4 Endress+Hauser
Liquiline CM442/CM444/CM448

If mounting outdoors, always use the weather protection cover (see "Accessories") to protect the
transmitter against weather conditions.

Application example Measuring point at wastewater treatment plant outlet (open channel)
• Transmitter CM444-AAM44A0FF with:
4x Memosens, Modbus TCP, 4 x relays for cleaning/limit value, 2 x analog current input
• pH and temperature with CPS11D, item 1, (www.products.endress.com/cps11d)
• Turbidity with CUS51D, item 2, (www.products.endress.com/cus51d)
• Nitrate with CAS51D, item 3, (www.products.endress.com/cas51d)
• Spectral absorption coefficient with CAS51D, item 4, (www.products.endress.com/cas51d)
• Flow from external measurement via current input
• Assembly holder CYH112 with assemblies CYA112 (www.products.endress.com/cyh112)

a0019831

Measuring point at wastewater treatment plant outlet

Data retention
• Storage of all measured values, incl. values of external sources, in the non-volatile memory (data
logbook)
• Data called up on site via user-defined measuring menu and load curve display of the data logbook
• Transmission of data by ethernet and storage in a tamper-proof database (Field Data Manager)
• Data export to csv file (for Microsoft Excel)

Endress+Hauser 5
 Liquiline CM442/CM444/CM448

Equipment architecture
Slot and port assignment

a0019832

a0019833

Slot and port assignment of the hardware modules

• Inputs are assigned to measuring channels in the
ascending order of the slots and ports.
Adjacent example:
"CH1: 1:1 pH glass" means:
Channel 1 (CH1) is slot 1 (basic module) : Port 1
(input 1), pH glass sensor
• Outputs and relays are named according to their
function, e.g. "current output", and are displayed with
the slot and port numbers in ascending order

Slot and port assignment on the display

Order of the modules Depending on the version ordered, the device is supplied with a number of electronic modules, which
are assigned in a specific sequence in ascending order to slots 0 to 7.
If you do not have a particular module, the next moves up automatically:
• The basic module (which is always present) always occupies slots 0 and 1
• Fieldbus module 485
• Memosens input module 2DS (DS = digital sensor)
• Extension module for digital inputs and outputs DIO (DIO = digital input and output)
• Current input module 2AI (AI = analog input)
• Current output module 4AO or 2AO (AO = analog output)
• Relay modules AOR, 4R or 2R (AOR = analog output + relay, R = relay)
Modules with 4 ports are connected before modules of the same type with 2 ports.

Basic rule for hardware Please note the following if upgrading the device:
upgrades The sum of all current inputs and outputs may not exceed 8!

6 Endress+Hauser
Liquiline CM442/CM444/CM448

Determining the hardware You must be aware of the type of modules and the number of them supplied with the device you have
delivery status ordered to determine the delivery status of your Liquiline.
• Basic module
– One basic module in all versions. Always occupies slots 0 and 1.
• Fieldbus module
– Optional, and only one fieldbus module is possible.
• Input modules
– Must be clearly assigned to the number of optional inputs ordered.
– Examples:
2 current inputs = module 2AI
4 Memosens inputs = 2 inputs with basic module + module 2DS with 2 further inputs
• Current outputs and relays
– Various module combinations can exist.
The following table will help you find out which modules you get depending on the type and
number of outputs.

Relay

Current 0 2 4
outputs

2 - 1 x 2R 1 x 4R

4 1 x 2AO 1 x AOR 1 x 2AO + 1 x 4R

6 1 x 4AO 1 x 4AO + 1 x 2R 1 x 4AO + 1 x 4R

8 1 x 4AO + 1 x 2AO 1 x 4AO + 1 x 2AO + 1 x 2R 1 x 4AO + 1x 2AO + 1 x 4R

‣ Sum up the number of modules and sort them according to the specified sequence.
 This will give you the slot assignment for your device.

Terminal diagram The unique terminal name is derived from the following:
Slot no. : Port no. : Terminal

Example, NO contact of a relay:

Device with 4 inputs for digital sensors, 4 current outputs and 4 relays
• Basic module BASE-E (contains 2 sensor inputs, 2 current outputs)
• Module 2DS (2 sensor inputs)
• Module 2AO (2 current outputs)
• Module 4R (4 relays)

a0015979

Creating a terminal diagram using the example of the NO contact (terminal 41) of a relay

Endress+Hauser 7
 Liquiline CM442/CM444/CM448

Device configuration CM442

using the example of a
CM442-**M1A1F0*

a0019808

CM442-**M1A1F0*

Ordered basic device (example) • Order code CM442-**M1A1F0*

• Functionality: 1 x Memosens, 2 current outputs without HART, no
extension module
Extension options without additional • Second Memosens input (71114663)
modules • HART with activation code (71128428)

Extension options by using an • Ethernet/PROFIBUS DP/Modbus with module 485 incl. activation
extension module in free slot 2 code for the desired communication type:
– PROFIBUS DP (71140888)
– Modbus RS485 (71140889)
– Modbus TCP (71140890)
– EtherNet/IP (71219868)
– Only Ethernet without fieldbus (71135634)
If fieldbus communication is subsequently required, an activation
code is needed for this.
If you retrofit a 485 module, any existing current outputs are
disabled!
• Additional inputs or outputs, relays:
– Module 2AI (71135639): 2 current inputs
– Module 2AO (71135632): 2 current outputs
– Module AOR (71111053): 2 current outputs, 2 relays
– Module 2R (71125375) or 4R (71125376): 2 or 4 relays
– Module DIO (71135638): 2 digital inputs and 2 digital outputs

Device upgrade to CM444 or CM448 • Upgrade kit 71135644 (100 to 230 V AC) or 71211434 (24 V DC)
– Extension power supply unit and backplane
– Basic module BASE-E (Memosens inputs same as for base device)
– 6 slots for extension modules
• Extension options:
– Second Memosens input (71114663), additional modules same
as for CM442
– Up to 8 measuring channels by using an appropriate number of
Memosens input modules 2DS (71135631)

Basic rule for extensions The sum of all current inputs and outputs may not exceed 8!

Restrictions if using CUS71D sensors • CM442:

for interface measurement Only one CUS71D can be connected. The second Memosens input
may not be used.
• If extending to CM444:
Every combination of CUS71D or other sensors is possible. All
Memosens inputs (max. 4) can be used.
• An extension to CM448 is not advisable as the maximum number
of Memosens inputs remains limited to 4.

Product Configurator www.products.endress.com/cm442

8 Endress+Hauser
Liquiline CM442/CM444/CM448

Function diagram CM442

a0015791

Function diagram CM442

1 Current output 1:1, + HART (optional) 6 Power supply

2 Current outputs (2 x optional) 7 Service interface
3 2 x Memosens input (1 x optional) 8 Power supply, fixed cable sensors
4 PROFIBUS DP/Modbus/Ethernet (optional) 9 Alarm relay
5 2 x current input (optional) 10 2 or 4 x relays (optional)
11 2 digital inputs and outputs (optional)

Endress+Hauser 9
 Liquiline CM442/CM444/CM448

Device configuration using

the example of a CM444-
**M42A1FA*

a0019809

CM444-**M42A1FA*

Ordered basic device (example) • Order code CM444-**M42A1FA*

• Functionality:
– 4 x Memosens (2 on BASE-E module + 2 on an extension module
2DS)
– PROFIBUS communication (module 485)
– 2 current outputs without HART (on BASE-E module)
– 2 current inputs (module 2AI)
• 3 slots are still free in this example. More or fewer slots can be free
in other versions.
Extension options without additional None
modules

Modification options without • Communication type changed by entering activation code

additional modules This disables the communication type used previously!
– Modbus RS485 (71135636)
– Modbus TCP (71135637)
– EtherNet/IP (71219868)
• Retrofit to HART by removing module 485 and entering activation
code for HART (71128428)
Extension options by using extension • Additional inputs or outputs, relays:
modules in free slots 5-7 – Module 2AI (71135639): 2 current inputs
– Module AOR (71111053): 2 current outputs, 2 relays
– Module 2R (71125375) or 4R (71125376): 2 or 4 relays
– Module DIO (71135638): 2 digital inputs and 2 digital outputs
• If fieldbus module 485 is used, no other current outputs are
available!

Device upgrade to CM448 6 or 8 measuring channels by using one or two Memosens input
modules 2DS (71135631)
Basic rule for extensions The sum of all current inputs and outputs may not exceed 8!

Restrictions if using CUS71D sensors • With the CM444, any combination of maximum 4 Memosens
for interface measurement sensors is possible.
• An extension to CM448 is not advisable as the maximum number
of Memosens inputs remains limited to 4 if a CUS71D is used.

Product Configurator www.products.endress.com/cm444

10 Endress+Hauser
Liquiline CM442/CM444/CM448

Function diagram CM444

a0015827

Function diagram CM444

1 Current output 1:1 + HART (both optional) 6 Power supply

2 Max. 7 x current output (optional) 7 Service interface
3 Memosens input (2 x standard + 2 x optional) 8 Power supply, fixed cable sensors
4 PROFIBUS DP/Modbus/Ethernet (optional) 9 Alarm relay
5 2 x current input (optional) 10 2 or 4 x relays (optional)
11 2 digital inputs and outputs (optional)

Endress+Hauser 11
 Liquiline CM442/CM444/CM448

Device configuration using

the example of a CM448-
**26A1*

a0019810

CM448-**26A1*

Ordered basic device (example) • Order code CM448-**26A1*

• Functionality:
– 6 x Memosens (2 on BASE-E module + 2 on two extension
modules 2DS)
– PROFIBUS communication (module 485)
• 3 slots are still free in this example. More or fewer slots can be free
in other versions.

Extension options without additional None

modules

Modification options without • Communication type changed by entering activation code

additional modules This disables the communication type used previously!
– Modbus RS485 (71135636)
– Modbus TCP (71135637)
– EtherNet/IP (71219868)
• Retrofit to HART by removing module 485 and entering activation
code for HART (71128428)

Extension options by using extension Only the following is possible for the example above:
modules in free slots 5-7 • Module 2R (71125375) or 4R (71125376): 2 or 4 relays
If extending to eight measuring channels:
• Module 2DS (71135631): 2 Memosens inputs
• Use of the 2 current outputs in the basic module by entering
activation code (71140891)
Additional inputs or outputs and relays if fieldbus module 485 is
removed:
• Module 2AO (71135632): 2 current outputs
• Module AOR (71111053): 2 current outputs, 2 relays
• Module 2R (71125375) or 4R (71125376): 2 or 4 relays
• Module DIO (71135638): 2 digital inputs and 2 digital outputs

Basic rule for extensions The sum of all current inputs and outputs may not exceed 8!

Restrictions if using CUS71D sensors The maximum number of Memosens inputs that can be used is limited
for interface measurement to 4! Here, every combination of CUS71D and other Memosens
sensors is then possible.

Product Configurator www.products.endress.com/cm448

12 Endress+Hauser
Liquiline CM442/CM444/CM448

Function diagram CM448

a0015828

Function diagram CM448

1 Current output 1:1 + HART (both optional) 7 Service interface

2 Max. 7 x current output (optional) 8 Power supply, fixed cable sensors
3 Max. 8 x Memosens input (of which 2 x optional) 9 Alarm relay
4 PROFIBUS DP/Modbus/Ethernet (optional) 10 2 or 4 x relays (optional)
6 Power supply 11 2 digital inputs and outputs (optional)

Endress+Hauser 13
 Liquiline CM442/CM444/CM448

Communication and data processing

Types of communication:
• Fieldbuses
– HART
– PROFIBUS DP (Profile 3.02)
– Modbus TCP or RS485
– EtherNet/IP
• Configuration via Ethernet
Only one type of Fieldbus communication can ever be active. The last activation code entered
decides which bus is used.
Extension module 485 and current outputs
For communication types PROFIBUS DP, Modbus and Ethernet:
• CM442:
Current outputs cannot be used in parallel. Any existing current outputs are deactivated with the
installation of 485.
• CM444/CM448:
Max. of 2 current outputs can be used in parallel.
Bus termination on the device
• Via slide switch at bus module 485
• Displayed via LED "T" on bus module 485

Dependability
Reliability Memosens technology
MEMO SENS

Memosens makes your measuring point safer and more reliable:

• Non-contact, digital signal transmission enables optimum galvanic isolation
• No contact corrosion
• Completely watertight
• Laboratory sensor calibration possible, thus increasing measured value availability
• Predictive maintenance thanks to recording of sensor data, e.g.:
– Total hours of operation
– Hours of operation with very high or very low measured values
– Hours of operation with high temperatures
– Number of steam sterilizations
– Sensor condition

Sensor Check System (SCS)

The Sensor Check System (SCS) monitors the high impedance of the pH glass.
An alarm is issued if a minimum impedance value is undershot or a maximum impedance is exceeded.
• Glass breakage is the main reason for a drop in high impedance values.
• The reasons for increasing impedance values include:
– Dry sensor
– Worn pH glass membrane.
For the SCS, upper and lower limit values can be enabled or disabled independently of one another.

Process Check System (PCS)

The process check system (PCS) checks the measuring signal for stagnation. An alarm is triggered if
the measuring signal does not change over a specific period (several measured values).
The main causes of stagnating measured values are:
• Contaminated sensor, or sensor outside of medium
• Sensor failure
• Process error (e.g. through control system)

14 Endress+Hauser
Liquiline CM442/CM444/CM448

Sensor Condition Check (SCC)

This function monitors the condition of the electrode and the degree of electrode aging. The status is
indicated by the messages "SCC bad" or "SCC sufficient". The condition of the electrode is updated after
every calibration.

Self-monitoring functions
Current inputs are deactivated in the event of overcurrent and reactivated once the overcurrent stops.
Board voltages are monitored and the board temperature is also measured.

USP and EP
The limit functions for pharmaceutical water in accordance with USP and EP specifications are
implemented in the software for conductivity measurements:
• Water for Injection (WFI) as per USP <645> and EP
• Highly purified water (HPW) as per EP
• Purified water (PW) as per EP
The uncompensated conductivity value and the temperature are measured for the USP/EP limit
functions. The measured values are compared against the tables defined in the standards. An alarm is
triggered if the limit value is exceeded. Furthermore, it is also possible to configure an early warning
alarm that signals undesired operating states before they occur.

ChemocleanPlus
Freely programmable sequence control
• e.g. for automatic sensor cleaning in retractable assemblies for reliable measurement results in
processes with a high risk of contamination
• Individual, time-based activation of 4 outputs e.g. relays
• Starting, stopping or pausing of activities via digital input or fieldbus signals e.g. from limit position
switches

Maintainability Modular design

The modular transmitter design means it can be easily adapted to suit your needs:
• Retrofit extension modules for new or extended range of functions, e.g. current outputs, relays and
digital communication
• Upgrade to maximum of eight-channel measurement
• Optional: M12 sensor connector for connecting any kind of Memosens sensor

a0016027 a0012440

CM444: Sample Fitting the extension module

Endress+Hauser 15
 Liquiline CM442/CM444/CM448

Data logger function

• Adjustable scan time: 1 to 3600 s (1 h)
• Data logbooks:
– Max. 8 data logbooks
– 150,000 entries per logbook
– Graphic display (load curves) or numerical list
• Calibration logbook: max. 75 entries
• Hardware version logbook:
– Hardware configuration and modifications
– Max. 125 entries
• Version logbook:
– E.g. software updates
– Max. 50 entries
• Operation logbook: max. 250 entries
• Diagnostics logbook: max. 250 entries

a0015032

Data logbook: Graphic display

Logbooks remain unchanged even after a software update.

SD card
The exchangeable storage medium enables:
• Quick and easy software updates and upgrades
• Data storage of internal device memory (e.g. logs)
• Transfer of complete configurations to a device with an identical setup (backup function)
• Transfer of configurations without the TAG and bus address to devices with an identical setup (copy
function)
Endress+Hauser offers industry-approved SD cards as accessories. These memory cards provide
maximum data security and integrity.
Other SD cards can also be used. However, Endress+Hauser does not accept any responsibility for the
data security of such cards.

External signals for device control and for activating external devices
Hardware options, e.g. module "DIO" with 2 digital inputs and 2 digital outputs or fieldbus module "485"
enable the following:
• via a digital input signal
– measuring range switching for conductivity (upgrade code required, see accessories)
– switching between different calibration datasets in the case of optical sensors
– an external hold
– a cleaning interval to be triggered
– switching on and off a PID controller, e.g. via the proximity switch of the CCA250
– the use of the input as an "analog input" for pulse-frequency modulation (PFM)
• via a digital output signal
– the static transmission (similar to a relay) of diagnostic states, point level switch states etc.
– the dynamic transmission (comparable to a non-wearing "analog output") of PFM signals, e.g. to
control dosing pumps.

16 Endress+Hauser
Liquiline CM442/CM444/CM448

FieldCare and Field Data Manager

FieldCare
Configuration and asset management software based on FDT/DTM technology
• Complete device configuration when connected via FXA291 and service interface
• Access to a number of configuration parameters and identification, measuring and diagnostic data
when connected via HART modem
• Logbooks can be downloaded in CSV format or binary format for "Field Data Manager" software
Field Data Manager
Visualization software and database for measuring, calibration and configuration data
• SQL database which is protected against manipulation
• Functions to import, save and print out logbooks
• Load curves to display measured values

a0016009

Field Data Manager: Load curves

Virtual process values (mathematical functions)

In addition to "real" process values, which are provided by connected physical sensors or analog inputs,
mathematical functions can be used to calculate a maximum of 6 "virtual" process values.
The "virtual" process values can be:
• Output via a current output or a Fieldbus
• Used as a regulating control variable
• Assigned as a measured variable to a limit contactor
• Used as a measured variable to trigger cleaning
• Displayed in user-defined measuring menus.
The following mathematical functions are possible:
• pH calculation based on two conductivity values acc. to VGB 405 RL, e.g. in boiler feed water
• Difference between two measured values from different sources, e.g. for membrane monitoring
• Differential conductivity , e.g. monitoring the efficiency of ion exchangers
• Degassed conductivity, e.g. for process controls in power plants
• Redundancy for monitoring two or three redundantly measuring sensors
• rH calculation based on the measured values of a pH and an ORP sensor

Endress+Hauser 17
 Liquiline CM442/CM444/CM448

Concentration tables
When the device is delivered from the factory, tables are saved in the device that allow inductive
conductivity measurements to be converted to concentrations of certain substances. 4 user-defined
tables are also possible.
The following factory concentration tables are available:

NaOH 0 ... 15 % 0 to 100 ˚C (32 to 212 ˚F)

HCl 0 ... 20 % 0 to 65 ˚C (32 to 149 ˚F)
HNO₃ 0 ... 30 % 2 to 80 ˚C (36 to 176 ˚F)
H2SO4 0 to 28 % and 35 to 85 % 0 to 100 ˚C (32 to 212 ˚F)
H2SO4 93 ... 100 % 0 to 100 ˚C (32 to 212 ˚F)
H3PO4 0 ... 40 % 2 to 80 ˚C (36 to 176 ˚F)
NaCl 0 ... 26 % 2 to 80 ˚C (36 to 176 ˚F)

Security Real-time clock

The device has a real-time clock, which is buffered by a button cell battery if the power supply fails.
This ensures that the device continues to keep the correct date and time when it is restarted and that
the time stamp for the logbooks is correct.

Data security
All settings, logbooks etc. are stored in a non-volatile memory to ensure that the data are retained even
in the event of a disruption to the power supply.

Measuring range switching for conductivity

• Can be used in CIP processes e.g. for safe monitoring of phase separations
• Switching between 4 complete parameter sets:
– Conductivity operating mode
– Concentration tables
– Temperature compensation
– Output signal range
– Limit value switch
• Via digital inputs or fieldbus

Measured value compensation for oxygen and conductivity

• Pressure or temperature compensation
• Input signals from external sensors via current input or fieldbus
• Signals from connected temperature sensors

Password protection
Password-protected login
• For remote operation via web server
• For local operation

Process safety
Two independent PID controllers
• One- or two-sided control
• Limit switches
• 4 cleaning programs which can be programmed independently of each other

IT security
We provide a warranty only if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any inadvertent
changes to the device settings.
IT security measures in line with operators' security standards and designed to provide additional
protection for the device and device data transfer must be implemented by the operators themselves.
Support in the performance of this task can be requested from Endress+Hauser.

18 Endress+Hauser
Liquiline CM442/CM444/CM448

Input
Measured variables --> Documentation of the connected sensor

Measuring ranges --> Documentation of the connected sensor

Types of input • Digital sensor inputs for sensors with Memosens protocol
• Analog current inputs (optional)
• Digital inputs (optional)

Input signal Depending on version

• Max. 8 x binary sensor signal
• 2 x 0/4 to 20 mA (optional), passive, potentially isolated from one another and from the sensor
inputs
• 0 to 30 V

Cable specification Cable type

Memosens data cable CYK10 or sensor fixed cable, each with cable end sleeves or M12 round-pin
connector

Cable length
Max. 100 m (330 ft)

Digital inputs, passive

Electrical specification • drawing power (passive)
• galvanically isolated

Span High: 11 to 30 V DC
Low: 0 to 5 V DC

Nominal input current Max. 8 mA

PFM function Minimum pulse width: 500 μs (1 kHz)

Test voltage 500 V

Cable specification Max. 2.5 mm2 (14 AWG)

Current input, passive

Span > 0 to 20 mA

Signal characteristic Linear

Internal resistance Non-linear

Test voltage 500 V

Endress+Hauser 19
 Liquiline CM442/CM444/CM448

Output
Output signal Depending on version:
• 2 x 0/4 to 20 mA, active, potentially isolated from one another and from the sensor circuits
• 4 x 0/4 to 20 mA, active, potentially isolated from one another and from the sensor circuits
• 6 x 0/4 to 20 mA, active, potentially isolated from one another and from the sensor circuits
• 8 x 0/4 to 20 mA, active, potentially isolated from one another and from the sensor circuits
• Optional HART communication (only via current output 1:1)

HART

Signal coding FSK ± 0.5 mA above current signal

Data transmission rate 1200 baud

Galvanic isolation Yes

Load (communication resistance) 250 Ω

PROFIBUS DP/RS485

Signal coding EIA/TIA-485, PROFIBUS DP-compliant acc. to IEC 61158

Data transmission rate 9.6 kBd, 19.2 kBd, 45.45kBd, 93.75 kBd, 187.5 kBd, 500 kBd,
1.5 MBd, 6 MBd, 12 MBd

Galvanic isolation Yes

Connectors Spring-cage terminal (max. 1.5 mm) bridged internally in the

connector (T function), M12 optional

Bus termination Internal slide switch with LED display

Modbus RS485

Signal coding EIA/TIA-485

Data transmission rate 2,400, 4,800, 9,600, 19,200, 38,400, 57,600 and 115,200
baud

Galvanic isolation Yes

Connectors Spring-cage terminal (max. 1.5 mm) bridged internally in the
connector (T function), M12 optional

Bus termination Internal slide switch with LED display

Ethernet and Modbus TCP

Signal coding IEEE 802.3 (Ethernet)

Data transmission rate 10/100 MBd

Galvanic isolation Yes

Connection RJ45, M12 optional

IP address DHCP or configuration using menu

EtherNet/IP

Signal coding IEEE 802.3 (Ethernet)

Data transmission rate 10/100 MBd

Galvanic isolation Yes

Connection RJ45, optional M12 (D-encoded)

IP address DHCP (default) or configuration via menu

20 Endress+Hauser
Liquiline CM442/CM444/CM448

Signal on alarm Adjustable, as per NAMUR Recommendation NE 43

• In measuring range 0 to 20 mA (HART is not available with this measuring range):
Error current from 0 to 23 mA
• In measuring range 4 to 20 mA:
Error current from 2.4 to 23 mA
• Factory setting for error current for both measuring ranges:
21.5 mA

Load Max. 500 Ω

Linearization/transmission Linear
behavior

Digital outputs, passive

Electrical specification • passive
• open collector, max. 30 V, 15 mA

PFM function Minimum pulse width: 500 μs (1 kHz)

Auxiliary voltage Electrical specification

• galvanically isolated
• unregulated, 24 V DC ± 20%
• max. 50 mA

Test voltage 500 V

Cable specification Max. 2.5 mm2 (14 AWG)

Current outputs, active

Span 0 to 23 mA
2.4 to 23 mA for HART communication

Signal characteristic Linear

Electrical specification Output voltage

Max. 24 V

Test voltage
500 V

Cable specification Cable type

Recommended: shielded cable

Cross-section
Max. 2.5 mm2 (14 AWG)

Endress+Hauser 21
 Liquiline CM442/CM444/CM448

Relay outputs
Electrical specification Relay types
• 1 single-pin changeover contact (alarm relay)
• 2 or 4 single-pin changeover contacts (optional with extension modules)

Relay switching capacity

Basic module (alarm relay)

Switching voltage Load (max.) Switching cycles

(min.)

230 V AC, cosφ = 0.8 to 1 0.1 A 700,000

0.5 A 450,000

115 V AC, cosφ = 0.8 to 1 0.1 A 1,000,000

0.5 A 650,000

24 V DC, L/R = 0 to 1 ms 0.1 A 500,000

0.5 A 350,000

Extension modules

Switching voltage Load (max.) Switching cycles

(min.)

230 V AC, cosφ = 0.8 to 1 0.1 A 700,000

0.5 A 450,000
2A 120,000

115 V AC, cosφ = 0.8 to 1 0.1 A 1,000,000

0.5 A 650,000
2A 170,000

24 V DC, L/R = 0 to 1 ms 0.1 A 500,000

0.5 A 350,000

2A 150,000

Minimum load (typical)

• Min. 100 mA with 5 V DC
• Min. 1 mA with 24 V DC
• Min. 5 mA with 24 V AC
• Min. 1 mA with 230 V AC

Cable specification Cross-section

Max. 2.5 mm2 (14 AWG)

22 Endress+Hauser
Liquiline CM442/CM444/CM448

Protocol-specific data
HART Manufacturer ID 11h

Device type 119Ch (CM44x), 119Dh (CSFxx)

Device revision 001h

HART version 7.2

Device description files (DD/DTM) www.endress.com

Device Integration Manager (DIM)

Device variables 16 user-definable and 16 predefined device variables, dynamic

variables PV, SV, TV, QV

Supported features PDM DD, AMS DD, DTM, Field Xpert DD

PROFIBUS DP Manufacturer ID 11h

Device type 155Dh (CM44x)

Profile version 3.02

GSD files www.products.endress.com/profibus

Device Integration Manager DIM

Output variables 16 AI blocks, 8 DI blocks

Input variables 4 AO blocks, 8 DO blocks

Supported features • 1 MSCY0 connection (cyclical communication, master class 1

to slave)
• 1 MSAC1 connection (acyclical communication, master class
1 to slave)
• 2 MSAC2 connections (acyclical communication, master
class 2 to slave)
• Device lock: The device can be locked using the hardware or
software.
• Addressing using DIL switches or software
• GSD, PDM DD, DTM

Modbus RS485 Protocol RTU/ASCII

Function codes 03, 04, 06, 08, 16, 23

Broadcast support for function codes 06, 16, 23

Output data 16 measured values (value, unit, status), 8 digital values (value,
status)

Input data 4 setpoints (value, unit, status), 8 digital values (value, status),
diagnostic information

Supported features Address can be configured using switch or software

Endress+Hauser 23
 Liquiline CM442/CM444/CM448

Modbus TCP TCP port 502

TCP connections 3

Protocol TCP
Function codes 03, 04, 06, 08, 16, 23

Broadcast support for function codes 06, 16, 23

Output data 16 measured values (value, unit, status), 8 digital values (value,
status)

Input data 4 setpoints (value, unit, status), 8 digital values (value, status),
diagnostic information

Supported features Address can be configured using DHCP or software

EtherNet/IP Protocol EtherNet/IP

ODVA certification Yes

Device profile Generic device (product type: 0x2B)

Manufacturer ID 0x049Eh

Device type ID 0x109Ch

Polarity Auto-MIDI-X
Connections (max.) CIP 12

I/O 6

Explicit 6
message

Multicast 3 consumers

Minimum RPI 100 ms (default)

Maximum RPI 10000 ms

System integration EtherNet/IP EDS

Rockwell Add-on-Profile Level 3, Faceplate for

FactoryTalk SE

IO data Input Device status and diagnostic message with

(T --> O) highest priority
Measured values:
• 16 AI (analog input) + Status + Unit
• 8 DI (discrete input) + Status

Output Actuating values:

(O --> T) • 4 A0 (analog output) + status + unit
• 8 DO (discrete output) + Status

Web server The web server enables full access to the device configuration, measured values, diagnostic messages,
logbooks and service data via standard WiFi/WLAN/LAN/GSM or 3G router with a user-defined IP
address.

TCP port 80

Supported features • Remote-controlled device configuration (1 session)

• Save/restore device configuration
• Logbook export (file formats: CSV, FDM)
• Access to web server via DTM or Internet Explorer
• Login
• Web server can be switched off

24 Endress+Hauser
Liquiline CM442/CM444/CM448

Power supply
Supply voltage CM442
Depending on version:
100 to 230 V AC ± 15 %, 50/60 Hz
24 V AC/DC +20/-15 %, 50/60 Hz
CM444 and CM448
Depending on version:
100 to 230 V AC ± 15 %, 50/60 Hz
24 V DC +20 / -15 %

NOTICE
The device does not have a mains switch.
‣ The customer must provide a protected circuit breaker in the vicinity of the device.
‣ This must be a switch or a power-circuit breaker and must be labeled as the circuit breaker for the
device.
‣ At the supply point, the power supply for the 24 V versions must be isolated from dangerous live
cables by double or reinforced insulation.

Fieldbus connection Supply voltage: not applicable

Power consumption CM442

Depending on supply voltage
• 100 to 230 V AC and 24 V AC:
Max. 55 VA
• 24 V DC:
Max. 22 W
CM444 and CM448
Depending on supply voltage
• 100 to 230 V AC:
Max. 73 VA
• 24 V DC:
Max. 68 W

Fuse CM442
5x20 mm, 250 V, 4.0 A, slow-blow (T4.0A)
CM444 and CM448
Fuse not exchangeable

Cable entries Identification of the cable entry on housing base Suitable gland

B, C, H, I, 1-8 M16x1.5 mm/NPT3/8"/G3/8

A, D, F, G M20x1.5 mm/NPT1/2"/G1/2

E -

) M12x1.5 mm

Recommended assignment

1-8 Sensors 1-8

A Power supply
B RS485 In or M12 DP/RS485
C Do not use
D,F,G Current outputs and inputs, relays
H Do not use
I RS485 Out or M12 Ethernet
E Do not use

a0018025

Endress+Hauser 25
 Liquiline CM442/CM444/CM448

Cable specification Cable gland Permitted cable diameter

M16x1.5 mm 4 to 8 mm (0.16 to 0.32")

M12x1.5 mm 2 to 5 mm (0.08 to 0.20")

M20x1.5 mm 6 to 12 mm (0.24 to 0.48")

NPT3/8" 4 to 8 mm (0.16 to 0.32")

G3/8 4 to 8 mm (0.16 to 0.32")

NPT1/2" 6 to 12 mm (0.24 to 0.48")

G1/2 7 to 12 mm (0.28 to 0.48")

Cable glands mounted at the factory are tightened with 2 Nm.

Electrical connection Basic module

a0012405 a0015871

Basic module BASE-H or -L (two-channel device) Basic module BASE-E (four- and eight-channel device)
1 Power supply for digital fixed cable sensors with 1 Power supply for digital fixed cable sensors with
Memosens protocol Memosens protocol
2 SD card slot 2 SD card slot
3 Slot for display cable1) 3 Slot for display cable1)
4 Service interface 4 Service interface
5 Connections for 2 Memosens sensors 5 Connections for 2 Memosens sensors
6 Current outputs 6 Current outputs
7 Power connection 7 LEDs
8 Fuse 8 Socket for internal supply cable 1)
9 Alarm relay connection 9 Alarm relay connection

1) Internal device connection. Do not disconnect the plug!

26 Endress+Hauser
Liquiline CM442/CM444/CM448

Connecting supply voltage for CM442

a0015825

Connecting power supply on the BASE-H or -L

H Power unit 100 to 230 VAC a0012404

L Power unit 24 VAC or 24 VDC Overall wiring diagram for BASE-H or -L

Connecting supply voltage for CM444 and CM448

a0015872 a0015873

Connecting power supply with BASE-E Overall wiring diagram BASE-E and extension power unit
(B)
A Internal supply cable
B Extension power supply unit

Endress+Hauser 27
 Liquiline CM442/CM444/CM448

Connecting optional modules With extension modules you can purchase additional functions for your device.

NOTICE
Unacceptable hardware combinations (due to conflicts in power supply)
Incorrect measurements or total failure of the measuring point as a result of heat build-up or
overloading
‣ If you are planning to extend your controller, make sure the resulting hardware combination is
permitted (Configurator on www.products.endress.com/cm442 or .../cm444 or .../CM448).
‣ Please note that if you are extending CM442 to CM444 or CM448, you must additionally fit an
extension power supply unit and an extension backplane. You must then also use basic module
BASE-E.
‣ Remember that the sum of all current inputs and outputs may not exceed 8!
‣ Please contact your Endress+Hauser sales center should you have any questions.

Module name

AOR 2R 4R 2DS DIO

a0015747 a0015748 a0015749 a0015754 a0019835

• 2 x 0/4 to 20 mA • 2 relays • 4 relays • 2 digital sensor • 2 digital inputs

analog outputs • Order no. • Order no. inputs • 2 digital outputs
• 2 relays 71125375 71125376 • 2 power supply with auxiliary
• Order no. systems for digital voltage
71111053 sensors • Order no.
• Order no. 71135638
71135631

a0015755 a0015758 a0015757 a0015756 a0019836

28 Endress+Hauser
Liquiline CM442/CM444/CM448

Module name

2AO 4AO 2AI 485

a0015750 a0015751 a0015752 a0015753

• 2 x 0/4 to 20 mA • 4 x 0/4 to 20 mA • 2 x 0/4 to 20 mA • Ethernet (web server

analog outputs analog outputs analog inputs or Modbus TCP)
• Order no. 71135632 • Order no. 71135633 • Order no. 71135639 • 5V power supply for
PROFIBUS DP
termination
• RS485 (PROFIBUS DP
or Modbus RS485)
• Order no. 71135634

a0015759 a0015760 a0015761 a0015762

PROFIBUS DP (module 485)

Contacts A - A’, B - B’ and C - C’ are bridged in the connector. This ensures that PROFIBUS
communication is not interrupted if the connector is disconnected.

Protective ground connection

a0012454

Cable mounting rail and associated function

1 Cable mounting rail 3 Additional threaded bolts for ground
2 Threaded bolt (protective ground connection, connections
central grounding point) 4 Cable clamps (fixing and grounding the sensor
cables)

Endress+Hauser 29
 Liquiline CM442/CM444/CM448

Sensor connection Sensors with Memosens protocol

Sensor types Sensor cables Sensors

Digital sensors without CYK10 with plug-in • pH sensors

additional internal power connection and inductive • ORP sensors
supply signal transmission • Combi sensors
• Amperometric oxygen sensors
• Conductive conductivity sensors
• Chlorine sensors

Fixed cable Inductive conductivity sensors

Digital sensors with Fixed cable • Turbidity sensors

additional internal power • Sensors for interface measurement
supply • Sensors for measuring the spectral
absorption coefficient (SAC)
• Nitrate sensors
• Optical oxygen sensors
• Ion-sensitive sensors

The following rule applies if connecting CUS71D sensors:

• CM442
– Only one CUS71D is possible; an additional sensor is not permitted.
– The second sensor input may also not be used for another type of sensor.
• CM444
No restrictions. All the sensor inputs can be used as required.
• CM448
– If a CUS71D is connected, the number of sensor inputs that can be used is limited to a maximum
of 4.
– Of these, all 4 inputs can be used for CUS71D sensors.
– Every combination of CUS71D and other sensors is possible, provided that the total number of
connected sensors does not exceed 4.
Connection methods
1. Sensor cable connected directly to the terminal connector of the sensor module 2DS or of the basic
module L, H or E
2. Optional: plug connection of the sensor cable connected to the M12 sensor socket on the
underside of the device. With this type of connection, the device is already wired at the factory.

1. Sensor cable connected directly

a0012459 a0012460

Sensors without additional supply voltage Sensors with additional supply voltage

30 Endress+Hauser
Liquiline CM442/CM444/CM448

a0016197

Sensors with and without additional supply voltage at sensor

module 2DS

2. Connection via M12 plug-in connection

Device versions with a pre-installed M12
socket are ready-wired upon delivery.
Install an M12 socket, which is available as an
accessory, in a suitable cable gland opening in
the base of the housing, and connect the cables
to the Memosens terminals of the sensor or
basic module as per the wiring diagram
(→ å ) .
Connecting the sensor
• Connect the sensor cable plug (pos. 1)
directly to the M12 socket.
Please note the following for these device
versions:
a0018021
• The internal device wiring is always the
M12 assignment Top:
socket Bottom: connector same regardless of what kind of sensor you
(top view in each case) connect to the M12 socket (plug&play).
1 PK (24 V) • The signal and power supply cables are
2 GY (Ground 24 V) assigned in the sensor plug-in head in such
3 BN (3 V)
a0018019 4 WH (Ground 3 V) a way that the PK and GY power supply
M12 plug-in connection (e.g. 5 GN (Memosens) cables are either used (e.g. optical sensors)
at sensor module) 6 YE (Memosens) or not (e.g. pH or ORP sensors).
7, NC Not connected
1 Sensor cable with M12
connector

Endress+Hauser 31
 Liquiline CM442/CM444/CM448

Performance characteristics
Response time Current outputs
t90 = max. 500 ms for an increase from 0 to 20 mA
Current inputs
t90 = max. 330 ms for an increase from 0 to 20 mA
Digital inputs and outputs
t90 = max. 330 ms for an increase from low to high

Reference temperature 25 ˚C (77 ˚F)

Maximum measured error of --> Documentation of the connected sensor

sensor inputs

Measured error for current Typical measured errors:

inputs and outputs < 20 μA (with current values < 4 mA)
< 50 μA (with current values 4 to 20 mA)
at 25 ˚C (77˚ F) each
Additional measured error depending on the temperature:
< 1.5 μA/K

Frequency tolerance of digital ≤1%

inputs and outputs

Resolution of current inputs < 5 μA

and outputs

Repeatability --> Documentation of the connected sensor

Installation
Mounting plate

a0012426

Mounting plate in mm (inch)

32 Endress+Hauser
Liquiline CM442/CM444/CM448

Weather protection cover

a0012428

Weather protection cover in mm (inch)

Installation instructions You require the post mounting kit (optional) to mount the unit on a pipe, post or railing (square or
circular, span range 20 to 61 mm (0.79 to 2.40")).

Post mounting

a0012665

Post mounting
1 Weather protection cover (optional) 5 Spring washers, nuts (post mounting kit)
2 Post mounting plate (post mounting kit) 6 Pipe or railing (circular/square)
3 Spring washers, nuts (post mounting kit) 7 Mounting plate
4 Pipe clamps (post mounting kit) 8 Threaded rods (post mounting kit)

Endress+Hauser 33
 Liquiline CM442/CM444/CM448

Rail mounting

a0012668

Rail mounting
1 Weather protection cover (optional) 6 Pipe or railing (circular/square)
2 Post mounting plate (post mounting kit) 7 Mounting plate
3 Spring washers, nuts (post mounting kit) 8 Threaded rods (post mounting kit)
4 Pipe clamps (post mounting kit) 9 Screws (post mounting kit)
5 Spring washers, nuts (post mounting kit)

Wall mounting
Mount the controller in such a way that the wall support surface is at least the size of the rear housing
panel.

a0012684 a0012685

Wall mounting Attach the device and click it into place

1 Wall
2 4 drill holes1)
3 Mounting plate
a0012686
4 Screws Ø 6 mm (not part of
Mounting distance in mm (inch) scope of supply)

1) The size of the drill holes depends on the wall plugs used. The wall plugs and screws must be
provided by the customer.

34 Endress+Hauser
Liquiline CM442/CM444/CM448

Environment
Ambient temperature range CM442
–20 to 60 ˚C (0 to 140 ˚F)
CM444
• Generally –20 to 55 ˚C (0 to 130 ˚F), with the exception of packages under the second point in the
list.
• -20 to 50 ˚C (0 to 120 ˚F) for the following packages:
– CM444-**M40A7FI******+...
– CM444-**M40A7FK******+...
– CM444-**N40A7FI******+...
– CM444-**N40A7FK******+...
CM448
• Generally –20 to 55 ˚C (0 to 130 ˚F), with the exception of packages under the second point in the
list.
• -20 to 50 ˚C (0 to 120 ˚F) for the following packages:
– CM448-***6AA******+...
– CM448-***8A4******+...
– CM448-***8A5******+...
– CM448-**28A3******+...
– CM448-**38A3******+...
– CM448-**48A3******+...
– CM448-**58A3******+...
– CM448-**68A3******+...
– CM448-**26A5******+...
– CM448-**36A5******+...
– CM448-**46A5******+...
– CM448-**56A5******+...
– CM448-**66A5******+...
– CM448-**22A7******+...
– CM448-**32A7******+...
– CM448-**42A7******+...
– CM448-**52A7******+...
– CM448-**62A7******+...

Storage temperature –40 to 80 ˚C (–40 to 175 ˚F)

Humidity 10 to 95%, not condensing

Degree of protection IP 66/67, impermeability and corrosion resistance in accordance with NEMA TYPE 4X

Vibration resistance Environmental tests

Vibration test based on DIN EN 60068-2, October 2008
Vibration test based on DIN EN 60654-3, August 1998

Post or pipe mounting

Frequency range 10 to 500 Hz (sinusoidal)
Amplitude 10 to 57.5 Hz: 0.15 mm
57.5 to 500 Hz: 2 g 1)
Test duration 10 frequency cycles/ spatial axis, in 3 spatial axes (1 oct./min)

Wall mounting
Frequency range 10 to 150 Hz (sinusoidal)
Amplitude 10 to 12.9 Hz: 0.75 mm
12.9 to 150 Hz: 0.5 g 1)
Test duration 10 frequency cycles/ spatial axis, in 3 spatial axes (1 oct./min)

1) g ... gravitational acceleration (1 g ≈ 9.81 m/s2)

Electromagnetic Interference emission and interference immunity as per EN 61326-1: 2006, class A for industry
compatibility

Endress+Hauser 35
 Liquiline CM442/CM444/CM448

Electrical safety IEC 61010-1, Class I equipment

Low voltage: overvoltage category II
Environment < 3000 m (< 9840 ft) above MSL

Pollution degree The product is suitable for pollution degree 4.

Pressure compensation to Filter made of GORE-TEX used as pressure compensation element

environment Ensures pressure compensation to environment and guarantees IP protection.

Mechanical construction
Dimensions

a0012396

Dimensions of field housing in mm (inch)

Weight Approx. 2.1 kg (4.63 lbs), depending on the version

36 Endress+Hauser
Liquiline CM442/CM444/CM448

Materials Lower housing section PC-FR

Display cover PC-FR

Display film and soft keys PE

Housing seal EPDM

Module side panels PC-FR

Module covers PBT GF30 FR

Cable mounting rail PBT GF30 FR, stainless steel 1.4301 (AISI304)

Clamps Stainless steel 1.4301 (AISI304)

Screws Stainless steel 1.4301 (AISI304)

Cable glands Polyamide V0 as per UL94

Operability
Display Graphic display:
• Back light with switch-off function
• Red display background for alarms alerts users to errors
• Transflective display technology for maximum contrast even in bright environments
• User-definable measuring menus mean you can always keep track of the values that are important
for your application.
• Load curve display

a0012437 a0012438

Backlit display Red background indicates an error

Operating concept The simple and structured operating concept sets new standards:
• Intuitive operation with the navigator and soft keys
• Fast configuration of application-specific measurement options
• Easy configuration and diagnosis thanks to plain-text display
• All languages that can be ordered are available in every device

a0012445 a0012786

Easy operation Plain-text menu

Endress+Hauser 37
 Liquiline CM442/CM444/CM448

Local operation Human interface

a0011764

Overview of operation
1 Display (with red display background in alarm condition)
2 Navigator (jog/shuttle function)
3 Soft keys (function depends on menu)

Remote operation Via HART (e.g. using HART modem and FieldCare)

a0015608

HART using modem

1 Device module Base-L, -H or -E: current output 1 with HART
2 HART modem to connect to PC, e.g. FXA1951)
3 HART handheld terminal

1) Switch position "on" (replaces resistance)

38 Endress+Hauser
Liquiline CM442/CM444/CM448

Via PROFIBUS DP

a0015874

PROFIBUS DP
T Terminating resistor

Via Modbus RS485

a0015875

Modbus RS485
T Terminating resistor

Endress+Hauser 39
 Liquiline CM442/CM444/CM448

Via Ethernet/Web server/Modbus TCP/EtherNet/IP

a0015876

Modbus TCP and/or Ethernet

Language packages The language selected in the product structure is the operating language preset at the factory.
All other languages can be selected using the menu.
• English (US)
• German
• French
• Swedish
• Spanish
• Italian
• Dutch
• Portuguese
• Polish
• Russian
• Turkish
• Chinese (Simplified, PR China)
• Japanese
• Czech

40 Endress+Hauser
Liquiline CM442/CM444/CM448

Ordering information
Product structure You can create a valid and complete order code using the Endress + Hauser Configurator tool on the
Internet.
Enter the following addresses in your browser to access the relevant product page:
www.products.endress.com/cm442
www.products.endress.com/cm444
www.products.endress.com/cm448
1. The following options are available on the right-hand side of the page:

2. Select "Configure this product".

3. A new window opens with the Configurator. Using this tool, you can configure your device and
you will receive a valid and complete order code for this.
4. Then export the order code as a PDF or as an Excel file selecting from the buttons provided at the
top of the page.

Scope of delivery • 1 controller in the version ordered

• 1 mounting plate
• 1 wiring label (attached at the factory to the inside of the display cover)
• 1 CD with Operating Instructions
• 1 printed copy of the Brief Operating Instructions in the language ordered

Certificates and approvals

4 mark Declaration of Conformity
The product meets the requirements of the harmonized European standards.
As such, it complies with the legal specifications of the EC directives.
The manufacturer confirms successful testing of the product by affixing to it the 4 mark.

cCSAus The product complies with "CLASS 2252 05 - Process Control Equipment" and "CLASS 2252 85 -
Process Control Equipment - Certified to US Standards" requirements.

FM/CSA CM442 only

FM/CSA Cl. I, Div. 2
The device has been developed and tested according to the following standards:
• FM3600 (1998)
• FM3611 (2004)
• FM3810 (2005)
• ANSI/ISA NEMA250 (1999)
• ANSI/IEC 60529 (2001)

MCERTS Application made for CM442

Endress+Hauser 41
 Liquiline CM442/CM444/CM448

Accessories
The most important accessories that could be delivered at the time this document went to print
are listed below. For information on accessories that are not listed here, please contact your local
service or sales representation.

Weather protection cover CYY101 weather protection cover for field devices, absolutely essential if operating the unit outdoors
• Material: stainless steel 1.4301 (AISI 304)
• Order No. CYY101-A

Post mounting kit Post mounting kit CM44x

• For securing the field housing to horizontal and vertical posts and pipes
• Order no. 71096920

Measuring cable Memosens data cable CYK10

• For digital sensors with Memosens technology
pH, redox, oxygen (amperometric), chlorine, conductivity (conductive)
• Order as per product structure (--> online Configurator, www.products.endress.com/cyk10)
• Technical Information TI00118C/07/EN
Memosens data cable CYK11
• Extension cable for digital sensors with Memosens protocol
• Order as per product structure (--> online Configurator, www.products.endress.com/cyk11)
Measuring cable CYK81
• Unterminated cable for extending sensor cables (e.g. Memosens)
• 2 x 2 cores, twisted with shielding and PVC sheath (2 x 2 x 0.5 mm2 + shielding)
• Material sold by the meter, Order No.: 51502543

Sensors Glass electrodes

Orbisint CPS11D
• pH sensor with Memosens technology
• Dirt-repellent PTFE diaphragm
• Order as per product structure (--> online Configurator, www.products.endress.com/cps11d)
• Technical Information TI00028C/07/EN
Memosens CPS31D
• pH sensor with Memosens technology
• Gel-filled reference system with ceramic diaphragm
• Order as per product structure (--> online Configurator, www.products.endress.com/cps31d)
• Technical Information TI00030C/07/EN
Ceraliquid CPS41D
• pH sensor with Memosens technology
• Ceramic diaphragm and KCl liquid electrolyte
• Order as per product structure (--> online Configurator, www.products.endress.com/cps41d)
• Technical Information TI00079C/07/EN
Ceragel CPS71D
• pH sensor with Memosens technology
• Poison-resistant reference with ion trap
• Order as per product structure (--> online Configurator, www.products.endress.com/cps71d)
• Technical Information TI00245C/07/EN
Orbipore CPS91D
• pH sensor with Memosens technology
• Open aperture diaphragm for media with high dirt load
• Order as per product structure (--> online Configurator, www.products.endress.com/cps91d)
• Technical Information TI00375C/07/EN
Orbipac CPF81D
• Compact pH sensor for installation or immersion operation in process water and wastewater
• Order as per product structure (--> online Configurator, www.products.endress.com/cpf81d)
• Technical Information TI191C/07/EN

42 Endress+Hauser
Liquiline CM442/CM444/CM448

Enamel pH electrodes
Ceramax CPS341D
• pH electrode with pH-sensitive enamel
• Meets highest demands of measuring accuracy, pressure, temperature, sterility and durability
• Order as per product structure (--> online Configurator, www.products.endress.com/cps341d)
• Technical Information TI00468C/07/EN

ORP sensors
Orbisint CPS12D
• ORP sensor with Memosens technology
• Dirt-repellent PTFE diaphragm;
• Order as per product structure (--> online Configurator, www.products.endress.com/cps12d)
• Technical Information TI367C/07/EN
Ceraliquid CPS42D
• ORP sensor with Memosens technology
• Ceramic diaphragm and KCl liquid electrolyte
• Order as per product structure (--> online Configurator, www.products.endress.com/cps42d)
• Technical Information TI373C/07/EN
Ceragel CPS72D
• ORP sensor with Memosens technology
• Poison-resistant reference with ion trap
• Order as per product structure (--> online Configurator, www.products.endress.com/cps72d)
• Technical Information TI374C/07/EN
Orbipac CPF82D
• Compact ORP sensor for installation or immersion operation in process water and wastewater
• Order as per product structure (--> online Configurator, www.products.endress.com/cpf82d)
• Technical Information TI191C/07/EN
Orbipore CPS92D
• ORP sensor with Memosens technology
• Open aperture diaphragm for media with high dirt load
• Order as per product structure (--> online Configurator, www.products.endress.com/cps92d)
• Technical Information TI435C/07/EN

pH ISFET sensors
Tophit CPS471D
• Sterilizable and autoclavable ISFET sensor with Memosens technology
• For the food and pharmaceutical industries, process engineering, water treatment and
biotechnology
• Order as per product structure (--> online Configurator, www.products.endress.com/cps471d)
• Technical Information TI283C/07/EN
Tophit CPS441D
• Sterilizable ISFET sensor with Memosens technology
• For media with low conductivity, with liquid KCl electrolyte
• Order as per product structure (--> online Configurator, www.products.endress.com/cps441d)
• Technical Information TI352C/07/EN
Tophit CPS491D
• ISFET sensor with Memosens technology
• Open aperture diaphragm for media with high dirt load
• Order as per product structure (--> online Configurator, www.products.endress.com/cps491d)
• Technical Information TI377C/07/EN

Endress+Hauser 43
 Liquiline CM442/CM444/CM448

pH and ORP combined sensors

Memosens CPS16D
• pH and ORP combined sensor for process engineering, with dirt-repellent PTFE diaphragm
• With Memosens technology
• Order as per product structure (--> online Configurator, www.products.endress.com/cps16d)
• Technical Information TI00503C/07/EN
Memosens CPS76D
• pH and ORP combined sensor for process engineering, hygiene and sterile applications
• With Memosens technology
• Order as per product structure (--> online Configurator, www.products.endress.com/cps76d)
• Technical Information TI00506C/07/EN
Memosens CPS96D
• pH and ORP combined sensor for chemical processes
• With poison-resistant reference with ion trap
• With Memosens technology
• Order as per product structure (--> online Configurator, www.products.endress.com/cps96d)
• Technical Information TI00507C/07/EN

Inductive conductivity sensors

Indumax CLS50D
• High-stability inductive conductivity sensor for standard, Ex and high-temperature applications
• Memosens protocol
• Order as per product structure (--> online Configurator, www.products.endress.com/cls50d)
• Technical Information TI182C/07/EN
Indumax H CLS54D
• Inductive conductivity sensor with certified, hygienic design for foodstuffs, beverages,
pharmaceuticals and biotechnology
• Order as per product structure, (--> Online Configurator, www.products.endress.com/cls54d)
• Technical Information TI00508C/07/EN

Conductive conductivity sensors

Condumax CLS15D
• Conductive conductivity sensor for measurement in pure and ultrapure water and in Ex applications
• Order as per product structure (--> online Configurator, www.products.endress.com/cls15d)
• Technical Information TI00109C/07/EN
Condumax CLS16D
• Hygienic conductivity sensor for measurement in pure and ultrapure water and in Ex applications
• With EHEDG and 3A certificates
• Order as per product structure (--> online Configurator, www.products.endress.com/cls16d)
• Technical Information TI227C/07/EN
Condumax CLS21D
• Two-electrode sensor in fixed cable and plug-in head version
• Order as per product structure (--> online Configurator, www.products.endress.com/cls21d)
• Technical Information TI085C/07/EN

44 Endress+Hauser
Liquiline CM442/CM444/CM448

Oxygen sensors
Oxymax COS51D
• Amperometric sensor for dissolved oxygen, with Memosens technology
• Order as per product structure (--> online Configurator, www.products.endress.com/cos51d)
• Technical Information TI00413C/07/EN
Oxymax COS61D
• Optical oxygen sensor for drinking water and industrial water measurement
• Measuring principle: quenching
• Memosens protocol
• Material: stainless steel 1.4571 (AISI 316Ti)
• Order as per product structure (--> online Configurator, www.products.endress.com/cos61d)
• Technical Information TI387C/07/EN
Oxymax COS22D
• Sterilizable sensor for dissolved oxygen
• Order as per product structure (--> online Configurator, www.products.endress.com/cos22d)
• Technical Information TI446C/07/EN

Chlorine sensors
CCS142D
• Membrane-covered amperometric sensor for free chlorine
• Memosens technology
• Measuring range 0.01 to 20 mg/l
• Order as per product structure (--> online Configurator, www.products.endress.com/ccs142d)
• Technical Information TI419C/07/EN

Ion selective sensors

ISEmax CAS40D
• Ion selective sensors
• Order as per product structure (--> online Configurator, www.products.endress.com/cas40d)
• Technical Information TI491C/07/EN

Turbidity sensors
Turbimax CUS51D
• For nephelometric measurements of turbidity and solids in wastewater
• 4-beam scattered light method
• With Memosens protocol
• Order as per product structure (--> online Configurator, www.products.endress.com/cus51d)
• Technical Information TI461C/07/EN

SAC and nitrate sensors

Viomax CAS51D
• SAC and nitrate measurement in drinking water and wastewater
• With Memosens protocol
• Order as per product structure (--> online Configurator, www.products.endress.com/cas51d)
• Technical Information TI459C/07/EN

Interface measurement
Turbimax CUS71D
• Immersion sensor for interface measurement
• Ultrasonic interface sensor
• Order as per product structure (--> online Configurator, www.products.endress.com/cus71d)
• Technical Information TI490C/07/EN

Endress+Hauser 45
 Liquiline CM442/CM444/CM448

Additional functionality Hardware extension modules

Kit CM442/CM444/CM448/CM442R/CM444R/CM448R/CSF48: extension module AOR
• 2 x relay, 2 x 0/4 to 20 mA analog output
• Order no. 71111053
Kit CM442/CM444/CM448/CM442R/CM444R/CM448R/CSF48: extension module 2R
• 2 x relay
• Order no. 71125375
Kit CM442/CM444/CM448/CM442R/CM444R/CM448R/CSF48: extension module 4R
• 4 x relay
• Order no. 71125376
Kit CM442/CM444/CM448/CM442R/CM444R/CM448R/CSF48: extension module 2AO
• 2 x 0/4 to 20 mA analog output
• Order no. 71135632
Kit CM444/CM448/CM444R/CM448R/CSF48: extension module 4AO
• 4 x analog output 0/4 to 20 mA
• Order no. 71135633
Kit CM444/CM448/CM444R/CM448R/CSF48: extension module 2DS
• 2 x digital sensor, Memosens
• Order no. 71135631
Kit CM442/CM444/CM448/CM442R/CM444R/CM448R/CSF48: extension module 2AI
• 2 x 0/4 to 20 mA analog input
• Order no. 71135639
Kit CM442/CM444/CM448/CM442R/CM444R/CM448R/CSF48: extension module DIO
• 2 x digital input
• 2 x digital output
• Auxiliary voltage supply for digital output
• Order no. 71135638
Kit CM442/CM444/CM448/CM442R/CM444R/CM448R/CSF48: extension module 485
• Ethernet configuration
• Can be extended to PROFIBUS DP or Modbus RS485 or Modbus TCP or EtherNet/IP. This requires an
additional activation code which can be ordered separately (→ ä 47).
• Order no. 71135634
Upgrade kit CM442/CM444/CM448/CM442R/CM444R/CM448R/CSF48
• Extension module 485
• PROFIBUS DP (+ Ethernet configuration)
• Order no. 71140888
Upgrade kit CM442/CM444/CM448/CM442R/CM444R/CM448R/CSF48
• Extension module 485
• Modbus RS485 (+ Ethernet configuration)
• Order no. 71140889
Upgrade kit CM442/CM444/CM448/CM442R/CM444R/CM448R/CSF48
• Extension module 485
• Modbus TCP (+ Ethernet configuration)
• Order no. 71140890
Upgrade kit CM442/CM444/CM448/CM442R/CM444R/CM448R/CSF48
• Extension module 485
• EtherNet/IP
(+ Ethernet configuration)
• Order no. 71219868
Kit CM442: upgrade kit to CM444/CM448
• Extension power supply unit 100 to 230 V AC and extension backplane
• Basic module BASE-E
• Order no. 71135644
Kit CM442: upgrade kit to CM444/CM448
• Extension power supply unit 24 V DC and extension backplane
• Basic module BASE-E
• Order no. 71211434

46 Endress+Hauser
Liquiline CM442/CM444/CM448

Firmware and activation codes

SD card with Liquiline firmware
• Industrial Flash Drive, 1 GB
• Order no. 71127100
Activation code for digital HART communication
• Order no. 71128428
Activation code for PROFIBUS DP
• Order no. 71135635
Activation code for Modbus RS485
• Order no. 71135636
Activation code for Modbus TCP
• Order no. 71135637
Activation code for EtherNet/IP
• Order no. 71219871
Kit CM442: activation code for 2nd digital sensor input
• Order no. 71114663
Kit CM444/CM448: upgrade code for 2 x 0/4 to 20 mA for BASE-E
• Order no. 71140891
Activation code for feedforward control
• Order no. 71211288
Activation code for measuring range switch
• Order no. 71211289

Software Memobase Plus CYP71D

• PC software to support laboratory calibration
• Visualization and documentation of sensor management
• Sensor calibrations saved in the database
• Order as per product structure, www.products.endress.com/cyp71d
• Technical Information TI00502C/07/EN
Field Data Manager Software MS30
• PC software for central data management
• Visualization of series of measurements and logbook events
• SQL database for secure data storage
• Order no. 71129799

Other accessories SD card

SD card
• Industrial Flash Drive, 1 GB
• Order no. 71110815

Cable glands
Kit CM44x: gland M
• Set, 6 pieces
• Order no. 71101768
Kit CM44x: gland NPT
• Set, 6 pieces
• Order no. 71101770
Kit CM44x: gland G
• Set, 6 pieces
• Order no. 71101771
Kit CM44x: dummy plug for cable gland
• Set, 6 pieces
• Order no. 71104942

Endress+Hauser 47
 Liquiline CM442/CM444/CM448

M12 socket and cable junction

Kit CM42/CM442/CM444/CM448: external CDI socket
• Socket with terminated connecting cables and counter nut
• Order no. 51517507
Kit CM442/CM444/CM448/CSF48: M12 socket for digital sensors
• Pre-terminated
• Order no. 71107456
Kit CM442/CM444/CM448/CSF48: M12 socket for PROFIBUS DP/Modbus RS485
• B-coded, pre-terminated
• Order no. 71140892
Kit CM442/CM444/CM448/CSF48: M12 socket for Ethernet
• D-coded, pre-terminated
• Order no. 71140893
Cable junction with Velcro strip
• 4 pieces, for sensor cable
• Order no. 71092051

Communication-specific accessories
Commubox FXA195 HART
• Intrinsically safe HART communication with FieldCare via the USB port
• Technical Information TI00404F
Commubox FXA291
• Connects the CDI interface of measuring devices with the USB port of the computer or laptop
• Technical Information TI00405C
WirelessHART adapter SWA70
• Wireless device connection
• Easily integrated, offers data protection and transmission safety, can be operated in parallel with
other wireless networks, minimum cabling complexity
• Technical Information TI00061S
Fieldgate FXA320
• Gateway for the remote interrogation of 4-20 mA measuring devices via a Web browser
• Technical Information TI00025S
Fieldgate FXA520
• Gateway for the remote diagnostics and configuration of connected HART devices via a Web browser
• Technical Information TI00051S
Field Xpert SFX100
• Compact, flexible and robust industrial handheld terminal for remote configuration and for
obtaining measured values via the HART current output
• Operating Instructions BA00060S

System components
RIA14, RIA16
• Field display unit for integration into 4 to 20 mA circuits
• RIA14 in flameproof metal enclosure
• Technical Information TI00143R and TI00144R
RIA15
• Process display unit, digital display unit for integration into 4 to 20 mA circuits
• Panel mounting
• With optional HART communication
• Technical Information TI01043K

48 Endress+Hauser
www.addresses.endress.com