Scribd
Upload
48 views

Mobile Phones, Etc. A Bluetooth Chip Is Designed To Replace Cables by Taking The Information

Bluetooth is a wireless technology standard that allows electronic devices such as computers, phones and headphones to connect without wires or cables. It uses short-wavelength UHF radio waves in the industrial, scientific and medical radio bands to establish ad hoc connections between devices. Bluetooth devices can communicate directly with each other within an effective range of around 10 meters. The Bluetooth standard defines different topology and architecture layers including piconets, scatternets, baseband and link manager protocols to enable wireless connections between devices.

Uploaded by

Sahil
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
48 views

Mobile Phones, Etc. A Bluetooth Chip Is Designed To Replace Cables by Taking The Information

Bluetooth is a wireless technology standard that allows electronic devices such as computers, phones and headphones to connect without wires or cables. It uses short-wavelength UHF radio waves in the industrial, scientific and medical radio bands to establish ad hoc connections between devices. Bluetooth devices can communicate directly with each other within an effective range of around 10 meters. The Bluetooth standard defines different topology and architecture layers including piconets, scatternets, baseband and link manager protocols to enable wireless connections between devices.

Uploaded by

Sahil
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Introduction

Bluetooth wireless technology is a short-range radio technology, which is developed for Personal
Area Network (PAN). Bluetooth is a standard developed by a group of electronics manufacturers
that allows any sort of electronic equipment -- from computers and cell phones to keyboards and
headphones -- to make its own connections, without wires, cables or any direct action from a user.
It is an ad hoc type network operable over a small area such as a room. Bluetooth wireless
technology makes it possible to transmit signals over short distances between telephones,
computers and other devices and thereby simplify communication and synchronization between
devices. It is a global standard that:

 Eliminates wires and cables between both stationary and mobile devices
 Facilitates both data and voice communication
 Offers the possibility of ad hoc networks and delivers the ultimate synchronicity between
all your personal devices

Bluetooth is a dynamic standard where devices can automatically find each other, establish
connections, and discover what they can do for each other on an ad hoc basis. Bluetooth is intended
to be a standard that works at two levels:

 It provides agreement at the physical level -- Bluetooth is a radio-frequency standard.


 It also provides agreement at the next level up, where products have to agree on when bits
are sent, how many will be sent at a time and how the parties in a conversation can be sure
that the message received is the same as the message sent.

It is conceived initially by Ericsson, before being adopted by a myriad of other companies,


Bluetooth is a standard for a small, cheap radio chip to be plugged into computers, printers,
mobile phones, etc. A Bluetooth chip is designed to replace cables by taking the information
normally carried by the cable, and transmitting it at a special frequency to a receiver Bluetooth
chip, which will then give the information received to the computer, phone whatever.

Topology
There are two types of topology for Bluetooth – Piconet, Scatternet. The Piconet is a small ad hoc
network of devices (normally 8 stations) as shown in Fig 1. It has the following features:

 One is called Master and the others are called Slaves


 All slave stations synchronizes their clocks with the master
 Possible communication - One-to-one or one-to-many
 There may be one station in parked state
 Each piconet has a unique hopping pattern/ID
 Each master can connect to 7 simultaneous or 200+ inactive (parked) slaves per piconet.
Figure 1 Piconet topology of Bluetooth

By making one slave as master of another Piconet, Scatternet is formed by combining several
Piconets as shown in Fig 2. Key features of the scatternet topology are mentioned below:

 A Scatternet is the linking of multiple co-located piconets through the sharing of


common master or slave devices.
 A device can be both a master and a slave.
 Radios are symmetric (same radio can be master or slave).
 High capacity system, each piconet has maximum capacity (720 Kbps)

Figure 2 Scatternet topology


Bluetooth Architecture
The Bluetooth architecture, showing all the major layers in the Bluetooth system, are depicted in
the Figure 3. The layers below can be considered to be different hurdles in an obstacle course. This
is because all the layers function one after the other. One layer comes into play only after the data
has been through the previous layer.

Figure 3. Bluetooth Architecture

 Radio: The Radio layer defines the requirements for a Bluetooth transceiver operating in
the 2.4 GHz ISM band.
 Baseband: The Baseband layer describes the specification of the Bluetooth Link
Controller (LC), which carries out the baseband protocols and other low-level link
routines. It specifies Piconet/Channel definition, “Low-level” packet definition, Channel
sharing
 LMP: The Link Manager Protocol (LMP) is used by the Link Managers (on either side)
for link set-up and control.

 HCI: The Host Controller Interface (HCI) provides a command interface to the
Baseband Link Controller and Link Manager, and access to hardware status and control
registers.

 L2CAP: Logical Link Control and Adaptation Protocol (L2CAP) supports higher
level protocol multiplexing, packet segmentation and reassembly, and the conveying of
quality of service information.

 RFCOMM: The RFCOMM protocol provides emulation of serial ports over the L2CAP
protocol. The protocol is based on the ETSI standard TS 07.10.

 SDP: The Service Discovery Protocol (SDP) provides a means for applications to
discover, which services are provided by or available through a Bluetooth device. It also
allows applications to determine the characteristics of those available services.
Questions

Q-1. Explain PicoNet in brief.


Ans: PicoNet is one of the two types of topology for Bluetooth. It is a small ad hoc network of
devices (normally 8 stations). Main points are as follows:
 One is called Master and the others are called Slaves
 All slave stations synchronizes their clocks with the master
 Possible communication - One-to-one or one-to-many
 There may be one station in parked state
 Each piconet has a unique hopping pattern/ID.
Each master can connect to 7 simultaneous or 200+ inactive (parked) slaves per piconet.

Q-2. Explain briefly the functions of Host Controller Interface(HCL) and Service Discovery
Protocol (SDP).
Ans: The Host Controller Interface (HCI) provides a command interface to the Baseband Link
Controller and Link Manager, and access to hardware status and control registers.
The Service Discovery Protocol (SDP) provides a means for applications to discover, which
services are provided by or available through a Bluetooth device. It also allows applications to
determine the characteristics of those available services.

Q-3. Explain Briefly The Device Addressing in BlueTooth.


Ans: Four possible types of addresses can be assigned to Bluetooth units.
 BD_ADDR: Bluetooth Device Address: Each Bluetooth transceiver is allocated a unique
48-bit device address. It is divided into a 24-bit LAP field, a 16-bit NAP field and an 8-bit
UAP field.
 AM_ADDR: Active Member Address: It is a 3-bit number. It is only valid as long as the
slave is active on the channel. It is also sometimes called the MAC address of a Bluetooth
unit.
 PM_ADDR: Parked Member Address: It is an 8-bit member (master-local) address that
separates the parked slaves. The PM_ADDR is only valid as long as the slave is parked.
 AR_ADDR: Access Request Address: This is used by the parked slave to determine the
slave-to master half slot in the access window it is allowed to send access request messages
in. It is only valid as long as the slave is parked and is not necessarily unique.

Q-4 Explain ACL (Asynchronous Connection-Less) link in brief.


Ans: The ACL link is a point-to-multipoint link between the master and all the slaves participating
on the piconet. In the slots not reserved for the SCO links, the master can establish an ACL link on
a per-slot basis to any slave, including the slave already engaged in an SCO link (packet switched
type). Only a single ACL link can exist. For most ACL packets, packet retransmission is applied.

Q-5. Give the functionalities of Link Manager Protocol


Ans: The Link Manager is responsible for managing the physical details for Bluetooth connections.
It is responsible for creating the links, monitoring their health, and terminating them gracefully
upon command or failure. The link manager is implemented in a mix of hardware and software.
The Link Manager carries out link setup, authentication, link configuration and other protocols. It
discovers other remote LM’s and communicates with them via the Link Manager Protocol (LMP).
To perform its service provider role, the LM uses the services of the underlying Link Controller
(LC). The Link Manager Protocol essentially consists of a number of PDU (protocol Data Units),
which are sent from one device to another, determined by the AM_ADDR in the packet header.

Q-6. In two lines give the functionalities of service discovery protocol (SDP).
Ans: The service discovery protocol (SDP) provides a means for applications to discover which
services are available and to determine the characteristics of those available services.

You might also like