Scribd
Upload
322 views7 pages

01j Audi Multitronic

This document provides instructions for removing and replacing the pinion shaft and differential ring gear on an Audi transmission. It includes the following steps: 1) Remove the half pulley, chain, and retaining nut from the secondary pulley. 2) Press out the old pinion shaft and remove the bearing and crown wheel. 3) Fit the new pinion shaft and crown wheel as a matched pair using a press. 4) The half pulley will need to be machined to specific diameters to fit the new, larger pinion shaft in order to restore tolerance. Failure to precisely machine the pulley could cause problems.

Uploaded by

LUIS ALEJANDRO
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
322 views7 pages

01j Audi Multitronic

This document provides instructions for removing and replacing the pinion shaft and differential ring gear on an Audi transmission. It includes the following steps: 1) Remove the half pulley, chain, and retaining nut from the secondary pulley. 2) Press out the old pinion shaft and remove the bearing and crown wheel. 3) Fit the new pinion shaft and crown wheel as a matched pair using a press. 4) The half pulley will need to be machined to specific diameters to fit the new, larger pinion shaft in order to restore tolerance. Failure to precisely machine the pulley could cause problems.

Uploaded by

LUIS ALEJANDRO
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Fitting

Instructions
Phone: Sales on 0208 848 9911
E-Mail: [email protected] www.vanmatic.com

Audi 01J
Output Shaft and Differential Ring Gear
Suitable for Audi CVT 6/7 Speed

New Pinion Shaft and


Ring Gear
Fitting
Instructions
Phone: Sales on 0208 848 9911
E-Mail: [email protected] www.vanmatic.com
To remove the shaft on the secondary pulley follow the steps illustrated below:

Fig. 1
To remove the chain and half
pulley (A)

Remove retaining nut (B)


(Fig 1)

Fig. 2
Remove the Half pulley using a
suitable puller
(Fig 2)

Fig. 3 The half Pulley Remove the Half pulley and then
will now require
Machining the chain
(Fig 3)

Important:
The half pulley will now
require machining before it can
be fitted onto the new pinion
shaft
See pages 5 & 6 for these instructions

Page 1
Fitting
Instructions
Phone: Sales on 0208 848 9911
E-Mail: [email protected] www.vanmatic.com
Continued:

To remove the pinion shaft, First


remove the differential (Fig 4)

Make sure you remove the snap


ring which is below the oil seal

The crown wheel must to replaced


with the new crown wheel supplied

Fig. 4 Use the correct tool to remove the


pinion shaft

After removal of the pinion shaft


remove the bearing ( Fig 5)

Fig. 5

The assembly is now ready for the


pinion shaft to be removed from
the half pulley (Fig 6)

Fig. 6

Page 2
Fitting
Instructions
Phone: Sales on 0208 848 9911
E-Mail: [email protected] www.vanmatic.com
Continued:

Using a suitable size tube place


Fig. 7 the assembly on a hydraulic
press (Fig 7)

Fig. 8 Press out the pinion shaft (Fig 8)

Fig. 9 Lift off the half pulley (Fig 9)

Page 3
Fitting
Instructions
Phone: Sales on 0208 848 9911
E-Mail: [email protected] www.vanmatic.com
Continued:

The half pulley and pinion shaft


should now be disassembled
(Fig 10)

Fig. 10

Old Old Pinion shaft and new crown


Shaft New crown wheel & pinion wheel and pinion shaft set
(Fig 11)

The new pinion shaft and crown


wheel must be fitted only as a
matched pair

Fig. 11

Using the tube again place the


Fig. 12 assembly back on a hydraulic
press and insert the new pinion
shaft (Fig 12)

Page 4
Fitting
Instructions
Phone: Sales on 0208 848 9911
E-Mail: [email protected] www.vanmatic.com

Machining Instructions

0
Ø 34.10 h6-0.016

This shaft has a slightly larger


diameter than the original
in order to restore tolerance
between the shaft and pulley.
The OEM value is around
33.85
The new shaft has a diameter
of:- 0
Ø 34.10 h6-0.016

Shaft breakage causes wear on diameter 1 & 2 of the pulley

In order to fit the old pulley


onto the new shaft it is
necessary to machine the
pulley to these new values
(Photo A)

Diameter 1 0
Ø 34.10 h6+0.016
Diameter 2 0
Ø 34.05 h6+0.016
Page 5
Fitting
Instructions
Phone: Sales on 0208 848 9911
E-Mail: [email protected] www.vanmatic.com

Machining Instructions

WARNING!!
It is very important to carry out this machining with the correct
equipment.

Please take care with the centering on the internal diameters of the
half pulley. The machining of the half pulley out of center will cause
problems with the gears not meshing correctly.

Technical specifications for correct machining

OEM Dimensions Machine to these Values

0 0
Ø 34.10 h6+0.016 Ø 34.05 h6+0.016
New value to restore OEM New value to restore OEM
tolerance between shaft and tolerance between shaft and
pulley pulley

All measurements in millimeters

Page 6

You might also like