www.alljntuworld.

in JNTU World

ELECTRICAL MACHINES-II LABORATORY

ELECTRICAL MACHINES-II
LABORATORY MANUAL

ld
or
W
TU
JN

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

DEPARTMENT OF ELECTRICAL AND ELECTRONICS

ENGINEERING

ELECTRICAL MACHINES-II LABARATORY

ld
LIST OF EXPERIMENTS

Sl.No Name of the Experiment Page no

or
1 OPEN CIRCUIT & SHORT CIRCUIT TEST ON A SINGLE PHASE 3
TRANSFORMER
2 SUMPNERS TEST 10

3
W
SCOTT CONNECTION OF TRANSFORMERS 15

4 NO LOAD AND BLOCKED ROTOR TEST ON A 3- ɸ 18

INDUCTION MOTOR

5 REGULATION OF ALTERNATOR USING SYNCHRONOUS 23

TU

IMPEDANCE METHOD

6 ‘V’ AND ‘INVERTED V’ CURVES OF SYNCHRONOUS MOTOR 29

7 EQUIVALENT CIRCUIT OF A SIGLE PHASE INDUCTION 35

MOTOR
8 BRAKE TEST ON 3- ɸ SQUIRREL CAGE INDUCTION MOTOR 40
JN

9 SEPARATION OF NO LOAD LOSSES IN 1-Φ TRANSFORMER 46

10 DETERMINATION OF Xd AND Xq OF SALIENT POLE 51

SYNCHRONOUS MOTOR

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

OPEN CIRCUIT & SHORT CIRCUIT TEST ON A SINGLE

PHASE TRANSFORMER
AIM:
To perform open circuit and short circuit test on a single phase transformer and to
pre-determine the efficiency, regulation and equivalent circuit of the transformer.

ld
APPARATUS REQUIRED:

Sl.
equipment Type Range Quantity
No.

or
(0-300)V 1 no
1 Voltmeter MI
(0-150)V 1 no

(0-2)A 1 no
2 Ammeter MI
W (0-20)A 1 no

(0-150)V LPF
3 Wattmeter Dynamo type 1 no
(0-2.5)A

(0-150)V UPF
TU

4 Wattmeter Dynamo type 1 no

(0-10)A

5 Connecting Wires ***** ***** Required

JN

Transformer Specifications:
Transformer Rating :( in KVA) _________
Winding Details:
LV (in Volts): _______________________
LV side current:_____________________
HV (in Volts): ______________________

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

HV side Current:___________________
Type (Shell/Core):___________________
Auto transformer Specifications:
Input Voltage (in Volts):______________
Output Voltage (in Volts): ____________
frequency (in Hz):____________________

ld
Current rating (in Amp):_____________

CIRCUIT DIAGRAM:
OPEN CIRCUIT:

or
W
TU

SHORT CIRCUIT:
JN

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

PROCEDURE:
Open circuit test:
1. Connections are made as per the circuit diagram.
2. Ensure that variac is set to zero output voltage position before starting the
experiment.
3. Switch ON the supply. Now apply the rated voltage to the Primary winding by

ld
using Variac.
4. The readings of the Voltmeter, ammeter and wattmeter are noted down in Tabular
form.
5. Then Variac is set to zero output position and switch OFF the supply.

or
6. Calculate Ro and Xo from the readings.

Short Circuit Test:

1. Connections are made as per the circuit diagram.
W
2. Ensure that variac is set to zero output voltage position before starting the
experiment.
3. Switch ON the supply. Now apply the rated Current to the Primary winding by
using Variac.
4. The readings of the Voltmeter, ammeter and wattmeter are noted down in Tabular
TU

form.
5. Then Variac is set to zero output position and switch OFF the supply.
6. Calculate Ro1 and Xo1 from the readings.

OBSERVATIONS:
I) For OC test
JN

Voltmeter Ammeter Wattmeter

Sl no. reading reading reading Ro Xo Cos ɸo
( Vo) (Io) Wo

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

II) For SC test

Voltmeter Ammeter Wattmeter
Sl no. reading reading reading Ro1 Zo1 Xo1
( VSC) (ISC) WSC

ld
MODEL CALCULATIONS:

Find the equivalent circuit parameters R0, X0, R01, R02, X01 and X02 from the O. C. and S.
C. test results and draw the equivalent circuit referred to L. V. side as well as H. V. side.

or
Let the transformer be the step-down transformer
Primary is H. V. side.
W V1
Secondary is L. V. side R0  where Iw = I0 cos 0
Iw

V1 WSC V
X0  Where Im = I0 sin 0 R01  2
, Z 01  SC
Im I sc I SC
TU

V2
X 01  Z 01  R01 : X 02  K 2 X 01 Where K =  Transformation ratio.
2 2

V1

Calculations to find efficiency and regulation

For example at ½ full load

Cupper losses = Wsc x (1/2)2 watts, where WSC = full – load cupper losses
JN

Constant losses = W0 watts

Output = ½ KVA x cos  [cos  may be assumed]

Input = output + Cu. Loss + constant loss

Output
% efficiency  x 100
Input

Efficiency at different loads and P.f’s

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

cos  = ___________

Regulation: From open circuit and Short circuit test

I 2 R02 cos   I 2 X 02 sin 

% Re gulation  x 100
V2

‘+’ for lagging power factors

ld
‘-‘ for leading power factor

p.f. % reg
S.No

or
Lag Lead

Cos = 1.0
W
S.No Load Wcu (W) O/P (W) I/P (W)  (%)
TU

Cos = 0.8

S.No Load Wcu (W) O/P (W) I/P (W)  (%)

JN

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

GRAPHS: Plots drawn between

(i) % efficiency Vs output

ld
or
(ii) % Regulation Vs Power factor
W
TU

PRECAUTIONS:
JN

(i) Connections must be made tight

(ii) Before making or breaking the circuit, supply must be switched off

RESULT:

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

SUMPNERS TEST

AIM:
To determine the efficiency and losses of a given transformer accurately under
full load condition.

ld
APPARATUS REQUIRED:

Sl.
Equipment Type Range Quantity
No.

or
(0-300)V 1 no

1 Voltmeter MI (0-300)V 1 no

(0-600)V 1 no
W (0-2)A 1 no
2 Ammeter MI
(0-20)A 1 no

(0-150)V LPF
3 Wattmeter Dynamo type 1 no
(0-2.5)A
TU

(0-150)V UPF
4 Wattmeter Dynamo type 1 no
(0-10)A

5 Connecting Wires ***** ***** Required

JN

Transformer Specifications:
Two identical 1- ɸ Transformers
Transformer Rating :(in KVA) ____________
Winding Details:
LV (in Volts): ________________________
LV side current:______________________

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

HV (in Volts): ________________________

HV side Current:______________________
Type(Shell/Core):______________________
1 - ɸ Auto transformer Specifications:
Input Voltage (in Volts):_________________
Output Voltage (in Volts): _______________

ld
Frequency (in Hz):______________________
Current rating (in Amp):_________________

CIRCUIT DIAGRAM:

or
W
TU
JN

PROCEDURE:
1. Make the connections as per the circuit diagram.

2. The secondary winding terminals of the two transformers are connected in series
with polarities in phase opposition which can checked by means of a voltmeter.

10

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

3. Before starting the experiment, check the variacs are in minimum output voltage
position.

4. Close the first DPST-1 switch and switch ON the supply.

5. Increase the variac slowly, and apply rated voltage to the primary windings of 1-
ɸ transformers and check the voltmeter reading connected across the secondary
terminals.

ld
6. If the voltmeter reading is Zero, continue with step 8.

7. If the voltmeter reading is not zero, interchange the secondary terminals.

or
8. Now close the DPST-2 switch and vary the variac-2 slowly till rated current flows
in the two series-connected secondaries.

9. Note down the readings of V1,V2, I1, I2, W1, and W2 and enter them in a tabular
column.
W
10. W1 = 2Pc, W2= 2Psc. Losses of each transformer = (W1+W2)/2

11. Now the Variacs are brought to zero voltage position and open DPST switches.
TU

OBSERVATIONS:

Sl Voltmeter Voltmeter Ammeter Ammeter Wattmeter Wattmeter Transformer ɳ

no. reading reading reading reading Reading Reading losses =
V1 V2 I1 I1 W1 W2 = (W1+W2)/2 op/(op+loss)
JN

MODEL CALCULATIONS:

wi  wc V I1
Losses in each transformer = %  combined = x 100
2 V I 1  wi  wc

11

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

V I1
Efficiency of each transformer (% )= x 100
w w
V I1  i  c
2 2

MODEL GRAPH:

ld
i) Output power Vs Efficiency

or
W
PRECAUTIONS:
TU

1. Connections must be made tight

2. Before making or breaking the circuit, supply must be switched off
RESULT:

VIVA QUESTIONS:
JN

1. What for this test is really intended?

2. Why to conduct the test on identical transformers?
3. What happens if the rated values of voltage and frequency of supply vary?
4. What are the advantages and disadvantages of this test?
5. Can you perform this test on 3 –  star/ delta transformers?
6. What is all-day efficiency?

12

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

SCOTT CONNECTION OF TRANSFORMERS

AIM:
To perform the Scott connection of transformer from three phases to two phase
connection.

APPARATUS REQUIRED:

ld
Sl.
Equipment Type Range Quantity
No.

(0-300)V 2 no

or
1 Voltmeter MI
(0-600)V 2 no

2 Ammeter MI (0-5)A 1 no

3 Connecting Wires ***** ***** Required

W
Transformer Specifications:
MAIN Transformer
Transformer Rating :( in KVA) ____________
TU

Winding Details:
LV (in Volts): _________________________
LV side current:_______________________
HV (in Volts): ________________________
HV side Current:______________________
Type(Shell/Core):______________________
JN

Tappings: ____________________________
TEASER Transformer
Transformer Rating :(in KVA) ___________
Winding Details:
LV (in Volts): _______________________
LV side current:______________________

13

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

HV (in Volts): _______________________

HV side Current:_____________________
Type(Shell/Core):____________________
Tappings: __________________________
3 - ɸ Auto transformer Specifications:
Input Voltage (in Volts):_________________

ld
Output Voltage (in Volts): _______________
Frequency (in Hz):_____________________
Current rating (in Amp):________________

or
CIRCUIT DIAGRAM:

W
TU
JN

PROCEDURE:
1. Connections are made as per the circuit diagram

2. Ensure that output voltage of the variac is set in zero position before starting the
experiment.

3. Switch ON the supply.

14

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

4. The output voltage of the variac is gradually increased in steps upto rated voltage
of single phase MAIN transformer and readings are correspondingly taken in
steps.

5. Enter the readings in tabular column.

6. After observations, the variac is brought to zero position and switch OFF the
supply.

ld
CALCULATIONS:

or
Prove

TABULAR COLUMN:
W Theoretical
Voltmeter Ammeter Voltmeter Voltmeter Voltmeter
Sl calculation
reading reading reading reading reading
no. V2TM =√ (V22T +
V1 I1 V2T V2M V2TM
V22M)
TU

RESULT:
JN

15

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

NO LOAD AND BLOCKED ROTOR TEST ON A 3- ɸ

INDUCTION MOTOR

AIM:

To determine the equivalent circuit of a 3- ɸ induction motor and calculate

ld
various parameters of induction motor with the help of circle diagram.

APPARATUS REQUIRED:

or
Sl.
Equipment Type Range Quantity
No.

1 Voltmeter MI (0-600)V 1 no

2 Ammeter
W MI (0-10)A 1 no

10A/600V UPF 1 no
3 Wattmeter Electro dynamo meter type
10A/600V LPF 1 no

4 Tachometer Digital ***** 1 no

TU

5 Connecting Wires ***** ***** Required

NAME PLATE DETAILS:

JN

Power rating

Voltage

Current

Speed(RPM)

16

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

Frequency

PF

3- ɸ Auto transformer Details:

ld
Input Voltage: __________________ (Volt)

Output Voltage: __________________ (Volt)

Current:_____________________ (Amp.)

or
CIRCUIT DIAGRAM:
W
TU
JN

PROCEDURE:

NO LOAD TEST:

1. Connections are made as per the circuit diagram.

17

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

2. Ensure that the 3- ɸ variac is kept at minimum output voltage position and belt is
freely suspended.

3. Switch ON the supply. Increase the variac output voltage gradually until rated
voltage is observed in voltmeter. Note that the induction motor takes large current
initially, so, keep an eye on the ammeter such that the starting current current
should not exceed 7 Amp.

ld
4. By the time speed gains rated value, note down the readings of voltmeter,
ammeter, and wattmeter.

5. Bring back the variac to zero output voltage position and switch OFF the supply.

or
BLOCKED ROTOR TEST:

1. Connections are as per the circuit diagram.

W
2. The rotor is blocked by tightening the belt.

3. A small voltage is applied using 3- ɸ variac to the stator so that a rated current
flows in the induction motor.

4. Note down the readings of Voltmeter, Ammeter and Wattmeter in a tabular

TU

column.

5. Bring back the Variac to zero output voltage position and switch OFF the supply.

OBSERVATIONS:

No Load Test:
JN

Sl no. Voltmeter Ammeter Wattmeter reading Wnl (Pnl)

reading reading
W1 W2 W1+W2
V nl Inl

18

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

Blocked Rotor Test

Sl no. Voltmeter Ammeter Wattmeter reading Wbr (Pbr)

reading reading
W1 W2 W1+W2
V br Ibr

ld
Measurement of stator winding resistance (r1):
CIRCUIT DIAGRAM:

or
W
TU

TABULAR COLUMN:

S no. Voltage (v) Ammeter (I) Resistance (R)

JN

Procedure to find r 1:

1. Connections are made as per the circuit diagram

2. Switch ON the supply. By varying the rheostat, take different readings of

ammeter and voltmeter in a tabular column.
19

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

3. From the above readings, average resistance r 1 of a stator is found

Measurement of Stator resistance

1. Connect the circuit as per the circuit diagram shown in fig (2).
2. Keeping rheostat in maximum resistance position switch on the 220 V Dc supply.
3. Using volt-ammeter method measure the resistance of the stator winding.

ld
4. After finding the stator resistance, Rdc must be multiplied with 1.6 so as to
account for skin effect i.e. Rac = 1.6 Rdc.
MODEL CALCULATIONS:
W0 I0
G0  , Y0  , B0  Y02  G02

or
3V 2 V

VSC WSC
Z 01  , R01  2
, X 01  2
Z 01  R 01
2

I SC 3 x I SC

For circle diagram

W
W0  W0 
cos  0  ,  0  cos 1  

3 V0 I 0  3 V0 I 0 

WS C  V 
cos  0  , IS N  ISC  0 
TU

V 
3 VSC I S C  SC 

PRECAUTIONS:

1. Connections must be made tight

JN

2. Before making or breaking the circuit, supply must be switched off

RESULT:

20

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

VIVA Questions:

1. Explain why the locus of the induction motor current is a circle.

2. What is the difference between the transformer equivalent circuit and induction
motor equivalent circuit?
3. What are the reasons in conducting no-load test with rated voltage and blocked-
rotor test with rated current?

ld
4. Why do you choose LPF wattmeter in load test and hpf wattmeter in blocked rotor
test?
5. How do you reverse the direction of rotation of induction motor?

or
6. What are the various applications of this motor?

W
TU
JN

21

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

REGULATION OF ALTERNATOR USING

SYNCHRONOUS IMPEDANCE METHOD

AIM:
To find the regulation of a 3 - ɸ alternator by using synchronous impedance
method.

ld
APPARATUS REQUIRED:
Sl.
Equipment Type Range Quantity

or
No.

1 Voltmeter MI (0-300/600)V 1 no

2 Ammeter MI (0-5/10)A 1 no

3 Ammeter
W MI (0-2.5/5)A 1 no

400 Ω /1.7A 1 no
3 Rheostat Wire-wound
145Ω /2A 2 no

4 Tachometer Digital ***** 1 no

TU

5 Connecting Wires ***** ***** Required

NAME PLATE DETAILS:

DC Motor(prime mover) 3- ɸ Alternator
JN

KW : Power Rating:
Voltage : PF :
Current : Line voltage:
Speed : Speed
Exctn : Shunt Exctn Voltage:
Voltage : Rated Current :

22

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

Field current::

CIRCUIT DIAGRAM:

ld
or
W
PROCEDURE:
Open Circuit Test:
TU

1. Make the connections as per the circuit diagram.

2. Before starting the experiment, the potential divider network in the alternator field
circuit and field regulator rheostat of motor circuit is set minimum resistance
position.

3. Switch ON the supply and close the DPST switch. The DC motor is started by
JN

moving starter handle.

4. Adjust the field rheostat of DC motor to attain rated speed (equal to synchronous
speed of alternator)

5. By decreasing the field resistance of Alternator, the excitation current of

alternator is increased gradually in steps.

23

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

6. Note the readings of field current, and its corresponding armature voltage in a
tabular column.

7. The voltage readings are taken upto and 10% beyond the rated voltage of the
machine.

Short Circuit Test:

ld
1. For Short circuit test, before starting the experiment the potential divider is
brought back to zero output position, i.e., resistance should be zero in value.

2. Now close the TPST switch.

or
3. The excitation of alternator is gradually increased in steps until rated current
flows in the machine and note down the readings of excitation current and load
current (short circuit current)

4. Switch OFF the supply.

W
OBSERVATIONS:

Sl OC test Sl S.C. test

TU

no. Field current in OC voltage no. Field current SC current

Amp.(I f) per phase (Vo) If( Amp.) Isc Amp.
JN

Procedure to find Armature resistance of alternator:

1. Connections are made as per the circuit diagram.

2. Switch ON the supply. By varying the rheostat, take different readings of

ammeter and voltmeter in a tabular column.

24

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

3. From the above readings, average resistance Ra of a armature is found out.

Connection diagram to find Ra

ld
or
W
OBSERVATIONS:
Sl no. Armature current Armature voltage Rdc=V / I
I(amp) Va (volts)
TU

Procedure to find synchronous impedance from OC and SC tests:

JN

1. Plot open circuit voltage, short circuit current verses field current on a graph
sheet.

2. From the graph, the synchronous impedance for the rated value of excitation is
calculated.

3. The excitation emf is calculated at full load current which is equal to the terminal
voltage at No load.

25

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

4. The voltage regulation is calculated at rated terminal voltage.

MODEL CALCULATIONS:

VOC
ZS  for the same If and speed: X S  Z S2  Ra2 [ Ra RdC]
I SC

ld
Generated emf of alternator on no load is

E0  v cos   I a Ra  2  v sin   I a X S 
2

+ for lagging p.f.

or
W
- for leading p.f.

The percentage regulation of alternator for a given p.f. is

TU

E0  V
% Re g  x 100
V

Where

E0 – generated emf of alternator (or excitation voltage per phase)

JN

V – full load, rated terminal voltage per phase.

MODEL GRAPHS:

Draw the graph between If VS E0 per phase

26

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

and If VS ISC

ld
or
PRECAUTIONS:
W
(iii) Connections must be made tight
(iv) Before making or breaking the circuit, supply must be switched off

RESULT:
TU
JN

27

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

‘V’ AND ‘INVERTED V’ CURVES OF SYNCHRONOUS

MOTOR
AIM:

To plot the ‘v’ and ‘inverted v’ curves of Synchronous motor.

ld
APPARATUS REQUIRED:

Sl.
Equipment Type Range Quantity

or
No.

1 Voltmeter MI (0-600)V 1 no

MC (0-2.5)A 1 no
2 Ammeter
W MI (0-10)A 1 no

3 Rheostat Wire-wound 400 Ω /1.7A 1 no

4 Tachometer Digital ***** 1 no

10A, 600V UPF 1 no

TU

5 Wattmeter Electrodynamometer
10A , 600V LPF 1 no

6 Connecting Wires ***** ***** Required

JN

NAME PLATE DETAILS

3- ɸ Synchronous motor
Power Rating:
PF
Line voltage:
Speed

28

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

Freq.
Rated Current :
Field current (If )
Field Voltage (Vf )

3- ɸ Auto transformer details

ld
Input voltage: ____________________(Volt)

Output Voltage : ___________________(Volt)

or
Frequency. :________________________(Hz)

Current: _________________________(Amp)
W
CIRCUIT DIAGRAM:
TU
JN

PROCEDURE:

1. Connections are made as per the circuit diagram.

29

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

2. Opening the SPST switch connected across the field DC supply is given to the
field and field current is adjusted to 0.3A ( 20% of rated field current)
3. The DC supply to the field is removed and SPST switch is connected across the
field by closing the switch
4. As 3- ɸ , 440V, 50Hz AC supply is applied to 3- ɸ dimmer stator keeping it in
minimum output position, keeping it prior to that motor is kept in no load state.

ld
5. Gradually supply voltage to synchronous motor is increased and then motor starts
running as squirrel cage induction motor. The direction of rotation is observed. if
it is not proper then supply phase sequence is altered.
6. Observing Ia, the voltage is gradually increased. It will reach a high value and

or
suddenly falls to a low value.
7. At that instant, open SPST switch connected across the field. The DC supply is
then given to the field. Then the motor is pulled into synchronism and motor now
works as a synchronous motor.
W
8. Gradually the supply voltage to stator is increased by observing the armature
current. If Ia, increases above the rated value then increase If such that Ia will be
within limits and thus full rated supply voltage is gradually given to the motor.
Now motor will work as synchronous motor with full rated voltage.
9. By varying If in steps, armature currents are recorded at no-load.
TU

10. By applying half of full load on motor, If and I a are recorded again. The same
experiment is repeated at 3/4th load, full load and corresponding readings are
recorded.
11. Completely removing the load on motor, the 3- ɸ supply to stator and then the
DC supply to the field are switched OFF
JN

OBSERVATION TABLE:

Sl Supply Wattmeter Wattmeter Field current Armature current Cos ɸ

no. voltage W1 W2 If(Amp) Ia(Amp)

30

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

Load 1 : 18.1% FL N = 1500 rpm VL = 415V S1 = 2.2 kg S2 = 5.2 lg

3 W1  W2 
Ia W1 W2 Tan  
If W1  W2   Cos
(A) (W) (W)
(A)

ld
Load 2 : 39.2% FL N = 1500 rpm VL = 415V S1 = 3.5 kg S2 = 9 kg

or
3 W1  W2 
Ia W1 W2 Tan  
If W1  W2   Cos
(A) (W) (W)
(A)
W
CALCULATIONS:
TU

Power factor = Cos [tan-1( )]

 3 W1  W2 
  Tan 1  
 W1  W2  

MODEL GRAPHS:
JN

31

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

RESULT:

VIVA Questions:

1. What are the difficulties in starting a synchronous motor?

2. What are the commonly employed methods of starting a synchronous motor?

ld
3. What are the applications of synchronous motor?
4. What is synchronous condenser?
5. What do you understand by hunting?

or
W
TU
JN

32

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

EQUIVALENT CIRCUIT OF A SIGLE PHASE INDUCTION

MOTOR
AIM:
To determine the equivalent circuit parameters of a single phase induction motor
by performing the
no- load and blocked rotor tests.

ld
APPARATUS REQUIRED:

Sl.

or
Equipment Type Range Quantity
No.

1 Voltmeter MI (0-300)V 1 no

2 Ammeter MI (0-10)A 1 no
W
(0-300)V LPF
3 Wattmeter Dynamo-type 1 no
(0-10)A

(0-150)V UPF
4 Wattmeter Dynamo-type 1 no
TU

(0-10)A

5 Connecting Wires ***** ***** Required

1 - ɸ Induction motor specifications:

JN

Name plate details

Sl. no. Quantity

1 rated power
2 Rated voltage

33

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

3 Current
4 Speed(RPM)
5 Cos ɸ (pf)
6 Frequency
7 rotor Squirrel
cage

ld
CIRCUIT DIAGRAM:

or
W
TU

PROCEDURE:
No load Test:
1. The circuit connections are made as per the circuit diagram.

2. Be sure that variac (auto transformer) is set to zero output voltage position before
starting the experiment.
JN

3. Now switch ON the supply and close the DPST switch.

4. The variac is varied slowly, until rated voltage is applied to motor and rated speed
is obtained.

5. Take the readings of Ammeter, Voltmeter and wattmeter in a tabular column.

34

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

6. The variac is brought to zero output voltage position after the experiment is done,
and switch OFF the supply.

Blocked Rotor Test:

1. To conduct blocked rotor test, necessary meters are connected to suit the full load
conditions of the motor.

ld
2. Connections are made as per the circuit diagram.

3. Before starting the experiment variac (auto transformer) is set to zero output
voltage position.

or
4. The rotor (shaft) of the motor is held tight with the rope around the brake drum.

5. Switch ON the supply, and variac is gradually varied till the rated current flows in
the induction motor.

6. Readings of Voltmeter, Ammeter, and wattmeter are noted in a tabular column.

W
7. The variac is brought to zero output voltage position after the experiment is done,
and switch OFF the supply.

8. Loosen the rope after the experiment is done.

TU

Calculation for No-Load Test:

JN

35

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

Calculation For Blocked Rotor Test:

ld
or
W
OBSERVATIONS:
For NO-Load Test:
Sl no. Voltmeter reading Ammeter reading Wattmeter reading
Vo Io Wo
TU

For Blocked Rotor Test:

Sl no. Voltmeter reading Ammeter reading Wattmeter reading
JN

Vsc Isc Wsc

PROCEDURE:
1. Connections are made as per the circuit diagram.

36

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

2. Initially rheostat is set at maximum resistance position.

3. Switch ON the supply, and vary the rheostat gradually and note down the readings
of ammeter and voltmeter

4. For the corresponding values, average of r1 is taken.

Circuit diagram for measurement of R1 :

ld
or
W
To find stator Resistance:

S.No I (A) V (volts) V

R= ()
I
TU
JN

Average Value: Rdc Rac Rdc =

37

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

Comments:
1. Since IM is not self starting Machine, it is started by placing an auxiliary winding
in the circuit.

2. Here no-load test is similar to open circuiting the load terminals and blocking the
rotor is similar to conducting short circuit on the IM.

ld
VIVA Questions:

1. Why there is no starting torque in a single phase induction motor?

2. What are different starting methods employed in single phase induction motors?

or
3. Compare the performance of capacitor - start, capacitor – run, shaded pole single
phase induction motors?
4. Mention a few applications of single phase induction motors?

PRECAUTIONS:
W
 Connections must be made tight
 Before making or breaking the circuit, supply must be switched off
TU
JN

38

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

BRAKE TEST ON 3- ɸ SQUIRREL CAGE INDUCTION

MOTOR

AIM:

To determine the efficiency of 3- ɸ induction motor by performing load test. To

ld
obtain the performance curves for the same.

APPARATUS REQUIRED:

or
Sl.
Equipment Type Range Quantity
No.

1 Voltmeter MI (0-600)V 1 no

2 Ammeter
W MI (0-10)A 1 no

10A/600V UPF 1 no
3 Wattmeter Electro dynamo meter type
10A/600V LPF 1 no
TU

4 Tachometer Digital 0-9999 RPM 1 no

5 Connecting Wires ***** ***** Required

NAME PLATE DETAILS:

JN

Power rating

Voltage

Current

Speed(RPM)

39

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

Frequency

PF

3- ɸ Auto transformer Details:

ld
Input Voltage: __________________ (Volt)

Output Voltage: _________________ _(Volt)

Current:_______________________(Amp.)

or
Freq.:___________________________(Hz)

CIRCUIT DIAGRAM:
W
TU
JN

PROCEDURE:

1. Connections are made as per the circuit diagram.

2. Ensure that the 3- ɸ variac is kept at minimum output voltage position and belt is
freely suspended.

40

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

3. Switch ON the supply. Increase the variac output voltage gradually until rated
voltage is observed in voltmeter. Note that the induction motor takes large current
initially, so, keep an eye on the ammeter such that the starting current current
should not exceed 7 Amp.

4. By the time speed gains rated value, note down the readings of voltmeter,
ammeter, and wattmeter at no-load.

ld
5. Now the increase the mechanical load by tightening the belt around the brake
drum gradually in steps.

or
6. Note down the various meters readings at different values of load till the ammeter
shows the rated current.

7. Reduce the load on the motor finally, and switch OFF the supply.
W
MODEL CALCULATIONS:

Input power drawn by the motor W = (W1 + W2) watts

Shaft Torque, Tsh = 9.81 (S1 ~ S2) R N-m R  Radius of drum in mts.
TU

2  N Tsh
Output power in watts = watts
60
output power in watts
% efficiency  x 100
Input power in watts

Ns  N  120 x f 
% slip  where N s  p 
x 100
JN

Ns 

W
power factor of the induction motor cos  
3 VL I L

41

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

MODEL GRAPHS:

1. Speed or slip Vs output power

2. Torque Vs output power
3. % efficiency Vs output power

ld
or
OBSERVATIONS:

S. V I Power, Speed Torque Spring % Slip Cos Ø Output %η

No. (Volts)
(Amps) W
W
(Watts) (RPM) (N-m)
balance Power

(Kg) (W)

W W2 S1 S2
1
TU
JN

42

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

PRECAUTIONS:

1. Connections must be made tight

2. Before making or breaking the circuit, supply must be switched off

RESULT:

ld
VIVA Questions:

1. Why starter is used? What are different types of starters?

or
2. Compare a slip ring induction motor with cage induction motor?
3. Why the starting torque is zero for a Single Phase induction motor and non-zero
of 3phase induction motor?
4. What are the disadvantages of this method?
W
5. Can we use rotor resistance method for starting?
TU
JN

43

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

SEPARATION OF NO LOAD LOSSES IN 1-Φ

TRANSFORMER
AIM:

To separation the Eddy current loss and Hysteresis loss from the iron loss of 1-Φ
transformer.

ld
APPARATUS REQUIRED:
Sl.

or
Equipment Type Range Quantity
No.

1 Voltmeter MI (0-300)V 1 no

2 Ammeter MC (0-2.5)A 1 no
W 370 Ω /1.7A 1 no
3 Rheostat Wire-wound
150Ω /2A 2 no

4 Tachometer Digital ***** 1 no

TU

5 Wattmeter Electro dynamo meter type 10A/600V LPF 1 no

6 Connecting Wires ***** ***** Required

NAME PLATE DETAILS:

DC Motor(prime 3- ɸ Alternator
JN

mover)
KW : Power Rating:
Voltage : PF :
Current : Line voltage:
Speed : Speed
Exctn : Shunt Exctn Voltage:

44

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

Voltage : Rated Current :

Field current::

Transformer Specifications:
Transformer Rating :( in KVA) _______________________
Winding Details:

ld
LV (in Volts): ___________________________
LV side current:_______________________
HV (in Volts): ___________________________
HV side Current:______________________

or
Type (Shell/Core):_________________________

CIRCUIT DIAGRAM:
W
TU
JN

PROCEDURE:

1. Make the circuit connections as per the circuit diagram.

2. The prime mover is started with the help of 3-point starter and it is made to run at
rated speed.

45

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

3. By varying alternators field rheostat gradually, the rated primary voltage is

applied to transformer.
4. By adjusting the speed of prime mover the required frequency, is obtained and
corresponding reading are noted.
5. The experiment is repeated for different frequency and corresponding readings are
tabulated.

ld
6. The prime mover is switched off using the DPIC switch after bringing all the
rheostats to initial position
7. From the tabulated readings the iron loss is separated from eddy current loss and
hysteresis loss by using respective formulae.

or
OBSERVATIONS:

Separation of No load losses in single phase Transformer:

W
Multiplication factor=

S.No Speed of Supply Primary Wattmeter Iron or core Wi/f

the prime frequency voltage readings(w) loss
mover (f)Hz (V)volts (Wi)watts
Observed Actual
TU

N(rpm)
(watts) (watts)

CALCULATIONS:
JN

1. Frequency(f)=PNs/120
Where P-number of poles; Ns-Synchronous speed in rpm

2. Hysteresis loss(Wh)=Af
3. Eddy current loss(We)=Bf2
4. Iron loss or core loss(Wi)= We +Wh

46

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

MODEL GRAPH:

The graph drawn as frequency Vs( Wi/f)

ld
PRECAUTIONS:

or
W
1. The motor field rheostat should be kept at minimum resistance position.
2. The alternator field rheostat should be kept maximum resistance position.
3. The motor should be run in anticlockwise direction.
4. Avoid loose connections.
TU

5. Take the readings with any parallax error.

VIVA Questions:

1. What are core losses in a transformer? Why they occur? On what factors do they
depend? What are the usual methods that are being employed in reducing them?
JN

2. How does change in frequency affect the operation of a given transformer?

3. A transformer is designed for 50C/S operation. It is worked at double and half the
designed frequency what changes do you except in the performance? Discuss?
4. Whether you can excite a transformer from a DC supply of rated voltage Justify
your answer

47

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

PRECAUTIONS:

1. Connections must be made tight

2. Before making or breaking the circuit, supply must be switched off

RESULT:

ld
or
W
TU
JN

48

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

DETERMINATION OF Xd AND Xq OF SALIENT POLE

SYNCHRONOUS MOTOR
AIM:

To determine the direct axis reactance Xd and quadrature axis reactance X q by

conducting a slip test on a salient pole synchronous machine.

ld
APPARATUS REQUIRED:

Sl.
Equipment Type Range Quantity
No.

or
1 Voltmeter MI (0-300)V 1 no

2 Ammeter MI (0-5)A 1 no

3 Rheostat Wire-wound 400 Ω /1.7A 1 no

4 Tachometer
W Digital ***** 1 no

5 Connecting Wires ***** ***** Required

NAME PLATE DETAILS:

TU

DC Motor (prime mover) 3- ɸ Alternator

KW : Power Rating:
Voltage : PF :
Current : Line voltage:
Speed : Speed
JN

Exctn : Shunt Exctn Voltage:

Voltage : Rated Current :
Field current::

49

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

3- ɸ Auto transformer Details:

Input Voltage: ________________(Volt)

Output Voltage: _______________(Volt)

Current:_____________________(Amp.)

ld
Frequency: ___________________(Hz)

CIRCUIT DIAGRAM:

or
W
TU

PROCEDURE:

1. Connections are made as per the circuit diagram.

2. Initially set field regulator, 3-ɸ variac at minimum position and TPST switch
open.
JN

3. The DC motor is started slowly by sliding starter handle and it is run at a speed
slightly less than the synchronous speed of the alternator.
4. Close the TPST switch.
5. With field winding left open, a positive sequence balanced voltages of reduced
magnitude (around 25% of rated Value) and of rated frequency are
impressed across the armature terminals.

50

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

6. The prime mover (DC motor) speed is adjusted till ammeter and voltmeters
pointers swing slowly between maximum and minimum positions.

7. Under this condition , readings of maximum and minimum values of both

ammeter and voltmeter are recorded

CALCULATIONS:

ld
Xd=

Xq =

Note:

or
W
1. When performing this test, the slip should be made as small as possible.
2. During Slip test, it is observed that swing of the ammeter pointer is very wide,
whereas the voltmeter has only small swing.

TABULAR COLUMN:
TU

Sl no. Speed Vmax Vmin Imax Imin Xd Xq

(VL) (VL) (IL) (IL)

JN

RESULT:

51

Downloaded From JNTU World (http://www.alljntuworld.in)

www.alljntuworld.in JNTU World

ELECTRICAL MACHINES-II LABORATORY

ld
or
W
TU
JN

52

Downloaded From JNTU World (http://www.alljntuworld.in)