WHITE PAPER

Overload or Short Circuit Protection?

How to protect your design against both dangers

E-T-A Circuit Breakers

PEC & Other Laws for Electrical Practitioner https://www.facebook.com/groups/506610139733827/

USA
E-T-A Circuit Breakers
1551 Bishop Court
Mt. Prospect, IL 60056
(847) 827-7600
fax: (847) 827-7655
[email protected]

CANADA
E-T-A Circuit Breakers Ltd.
100 Leek Cr., Unit 11
Richmond Hill, ON L4B 3E6
(905) 764-9510
fax (905) 764-8003
[email protected]

www.e-t-a.com downloaded from: PEC & Other Laws for Electrical Practitioner https://www.facebook.com/groups/506610139733827/
 WHITE PAPER

Overload or Short Circuit Protection?

Short circuits and overloads put different demands on circuit breakers. It is
imperative that engineers know how to protect their design against both dangers.

Circuit breakers are used in a variety of ways. They are mounted in panelboards to protect branch cir-
cuit wiring, and they are built into equipment to protect it. With this range of applications, it’s not sur-
prising that a circuit breaker must provide both short circuit and overload protection.

Interrupting a short circuit current that’s limited only by the resistance of the wiring is a very severe test
of a circuit breaker, and if the interrupting
PEC & capacity
Other Laws for Electrical of the breaker is not adequate, the device can liter-
Practitioner https://www.facebook.com/groups/506610139733827/

ally explode. Overload currents that reach 2 to 5 times the normal rating of the breaker are handled
differently, and very often the circuit breaker must carry the current for an appreciable time without trip-
ping. This white paper will give pointers on how to determine the main job a breaker must do and how
to make an appropriate selection.

Protection against shorts and overloads is the largest concern when choosing a circuit breaker. Branch
circuits fed from a 480V main need protection against short circuit currents measured in ten of thou-
sands of amperes. For that reason panelboards are equipped with circuit breakers for branch circuit
protection that are listed under UL 489, “Standard for Molded-Case Circuit Breakers and Circuit
Breaker Enclosures,” and rated to interrupt fault currents from 5000 to 50,000 amperes or higher.

A circuit breaker installed inside a piece of equipment is generally there to protect the equipment itself,
and the applicable standard should be UL 1077, “Standard for Supplementary Protectors for Use in
Electrical Equipment.” In UL terms, UL 1077 compliant devices are called “supplementary protectors,”
and are labeled as “recognized components” (not “listed”), and are identified with the
symbol. They are often called “circuit breakers for equipment” (CBEs). While both UL 489 breakers
and UL 1077 devices protect against both shorts and overloads, UL 1077 devices tend to concentrate
more on overloads - largely because they are always down stream of a UL 489 breaker.

2
downloaded from: PEC & Other Laws for Electrical Practitioner https://www.facebook.com/groups/506610139733827/
www.e-t-a.com/us_wp.html
 WHITE PAPER
Protection against short circuits
All circuit breakers are tested for short circuits but the severity of a short circuit depends on where it is
used in the circuit. Not all devices will continue working after opening a short circuit. Standards
UL 489 and UL 1077 have different requirements.

UL 489 requires that the breaker remains working after being subjected to a short circuit test, but
UL 1077 and the IEC and EN 60934 allow for breakers to clear a short but be safely destroyed in the
process. Whether a breaker will or will not survive a short circuit depends on the magnitude of current
involved. Whether it’s mentioned on the data sheet or not, every circuit breaker has two ratings for
interrupting capacity. One specifies the maximum amount of current the breaker can safely interrupt
and still remain operable afterwards (officially known as “fit for further use” or “recalibrated after test-
ing”). Under EN 60934 this is the PC2 rating, while under UL 1077 it’s the SC 2 value (Fig 1).

The other (generally much higher) interrupting rating specifies the maxi-
PEC & Other Laws for Electrical Practitioner https://www.facebook.com/groups/506610139733827/

mum current that the breaker can interrupt safely (ie., without starting a
fire) but may be rendered inoperable (“not fit for further use” or “not recal-
ibrated after testing”). Under EN 60934 this is the PC1 rating, while
under UL 1077 it’s the SC1 value. Some manufacturers publish both rat-
ings, but many do not.

Protection against overloads

Overloads can be short-term or long-term. The protective device chosen
Fig. 1: The E-T-A 2210-S thermal-
magnetic circuit breaker can inter- must not trip on momentary or short-term overcurrent events that are nor-
rupt 700 amps at 277 VAC and
remain operable afterwards
mal for the piece of equipment it is protecting. Electronic devices, for
example, may create inrush currents as their internal power supply and
filter circuits start. These inrush currents typically last only a fraction of a second, and seldom cause a
problem. Another class of short-term overcurrents is a motor starting surge. Most motors, especially
those that start under load, draw several times their normal current when starting. Other overcurrents
may last even longer, and still be part of normal operation. A piece of motor-driven equipment, for
example, may draw 50% more than normal current for several minutes at a time and the breaker
should not trip under these conditions. If the overload lasts longer than normal, the breaker should
open to prevent overheating and damage. What gives the breaker the ability to discriminate between
normal and damaging overcurrents is the delay curve.
3
downloaded from: PEC & Other Laws for Electrical Practitioner https://www.facebook.com/groups/506610139733827/
www.e-t-a.com/us_wp.html
 WHITE PAPER
Delay curves
There are four choices of delay curves in circuit breakers: thermal, thermal-magnetic, hydraulic-
magnetic, and magnetic. Each has a different trip profile in relation to time and current, and each has
distinct mechanical characteristics.

Thermal breakers incorporate a heat-responsive bimetal strip or disk.

This type of technology has a slower characteristic curve that discrimi-
nates between safe temporary surges and prolonged overloads. It is
appropriate for machinery or vehicles where high inrush currents accom-
pany the start of electric motors, transformers, and solenoids. There are
some thermal circuit breakers with hot-wire elements, which provide
faster switching. They provide a low cost solution for appliances and
printed circuit board protection, among other applications.
PEC & Other Laws for Electrical Practitioner https://www.facebook.com/groups/506610139733827/

Thermal-magnetic breakers combine the benefits of a thermal and mag-

netic circuit breaker: they have a thermal delay that avoids nuisance trip-
ping caused by normal inrush current, and a magnetic solenoid for fast
response at higher currents (Fig. 2).

Both standard thermal and thermal-magnetic circuit breakers are sensi-

tive to ambient temperature. However, they can be selected to operate
properly in a wide temperature range.
Fig 2: E-T-A’s 2210-S circuit breakeris
available with trip curves ranging from
fast-acting to delayed thermal-magnetic
A magnetic circuit breaker can be combined with a hydraulic delay to to a pure thermal version.

make it tolerant of current surges. These hydraulic-magnetic breakers

are similar to the thermal-magnetic in that they have a two step response curve -- they provide a delay
on normal overcurrents, but trip quickly on short circuits. Many hydraulic-magnetic circuit breakers are
available in a selection of delay curves to fit particular applications. Hydraulic-magnetic circuit breakers
are not affected by ambient temperature, but they tend to be sensitive to position. These breakers
should be mounted in a vertical plane to prevent gravity from influencing the movement of the solenoid.
If mounted in a different position, derating may be needed.

4
downloaded from: PEC & Other Laws for Electrical Practitioner https://www.facebook.com/groups/506610139733827/
www.e-t-a.com/us_wp.html
 WHITE PAPER
Pure magnetic circuit breakers operate via a solenoid and trip nearly instantly as soon as the threshold
current has been reached. This type of delay curve is appropriate for sensitive equipment such as
telecommunication equipment, printed circuit boards, and impluse disconnection in control appliances.

Conclusion
There are several UL standards covering circuit breakers and other protective devices for use in a wide
variety of equipment types; choosing carefully can save considerable cost and provide protection tai-
lored to that application. The drawback to this is that the designer must do more homework to select
the appropriate device. Considering the money that can be saved, that’s probably time well spent.

PEC & Other Laws for Electrical Practitioner https://www.facebook.com/groups/506610139733827/

5
downloaded from: PEC & Other Laws for Electrical Practitioner https://www.facebook.com/groups/506610139733827/
www.e-t-a.com/us_wp.html