Scribd
Upload
168 views

Lab Report Final Project Survey

This document is the final project report for an engineering survey fieldwork class. It describes the group members, lecturer, date, and purpose of conducting a field survey to measure horizontal distances, angles, heights, and bearings at survey stations laid out around a given area. The report sections document the devices used, procedures followed, products and analysis of the field measurements, discussion of the results, and conclusions drawn, with references cited at the end.

Uploaded by

Saibatul As-syahidah
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
168 views

Lab Report Final Project Survey

This document is the final project report for an engineering survey fieldwork class. It describes the group members, lecturer, date, and purpose of conducting a field survey to measure horizontal distances, angles, heights, and bearings at survey stations laid out around a given area. The report sections document the devices used, procedures followed, products and analysis of the field measurements, discussion of the results, and conclusions drawn, with references cited at the end.

Uploaded by

Saibatul As-syahidah
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 14

FACULTY OF ENGINEERING TECHNOLOGY

FINAL PROJECT

SUBJECT CODE BET1142

SUBJECT NAME ENGINEERING SURVEY FIELDWORK

DATE 4/12/2015

GROUP NUMBER 6

GROUP MEMBER: HAIQAL NURSYAKIRIN BIN MD


ARSHAD (TE15048)
NAME & ID NO
MOHAMAD FITRI HAFIFI BIN MOHD
NORDIN (TE15053)

NUR ANISAH AMIRAH BINTI MOHD


ASRI (TE15039 )

NUSAIBATUL AS-SYAHIDAH BT ISHAK


(TE15052)

NURUL AQILAH BT MOHD RASUL


(TE15050)

LECTURE ENCIK SHUHAIMI BIN SHAEDON

REMARKS

ENDORSEMENT
CONTENT

TITLE PAGE

INTRODUCTION 3

OBJECTIVE 4

DEVICE 5-6

PROCEDURE 7

PRODUCT & ANALYSIS 8-10

DISCUSSION 14-15

CONCLUSION 16-17

APPENDIX & REFERENCE 18-19

2
INTRODUCTION

OBJECTIVE

3
DEVICES
DEVICES for traverse:

THEODOLITE

TRIPOD

PRISM

4
DEVICES for levelling:

TOPCORN

HAMMER

BUBBLE

5
PICKET

MEASURING TAPE

NAILS

STAFF

6
MINI PRISM

TRIPOD

7
PROCEDURE
First of all the traverse stations were fixed around the
given area to the surveyed keeping in the ratio of traverse
legs 1:2 for major and 1:3 for minor traverse. The number
of the stations were choosen in convenient manner.

Measurement of the horizontal distance of the traverse


legs were taken by the tape. Two ways is forward and
backward measurement of each traverse leg were taken.

Now, with the help of theodelite two sets of horizontal


angle between the traverse legs were measured.

At the same time, one set of vertical angle were also


measured.

The height of the instrument in every set up of theodelite


was also measured.

Now, with help of level machine, the height of signal or


say RL of each stations with respect to the given assumed
BM was measured.

With the help of prismatic compass, magnetic bearing of


one traverse line was measured.

8
PRODUCT & ANALYSIS

9
10
11
ANALYSIS

APPENDIX

12
DISCUSSION

CONCLUSION

REFERENCES

1. Manual lab
2. Lecture note
3. http://www.slideshare.net/x3HwaN/site-surveying-report-i
4. http://allaboutengineeringworks.blogspot.my/2012/02/lab-report-leveling-
survey-longitudinal.html

13
5. http://ag.arizona.edu/classes/ABE404/Lectures/SurveyingFieldNotes.pdf

14

You might also like