Scribd
Upload
1K views14 pages

Roof by Extrusion in Revit

The document provides instructions for creating a roof by extrusion in Autodesk Revit. It involves: 1) Creating reference lines to define the start and end of the roof. 2) Using the "Roof by Extrusion" tool and selecting a reference plane to sketch the roof profile. 3) Drawing the roof profile and assigning a roof type. 4) Extruding the roof to the end reference line and attaching walls to form the roof base. 5) Optional steps to cut out portions of the roof by sketching openings in plan view.

Uploaded by

Amer Gonzales
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
1K views14 pages

Roof by Extrusion in Revit

The document provides instructions for creating a roof by extrusion in Autodesk Revit. It involves: 1) Creating reference lines to define the start and end of the roof. 2) Using the "Roof by Extrusion" tool and selecting a reference plane to sketch the roof profile. 3) Drawing the roof profile and assigning a roof type. 4) Extruding the roof to the end reference line and attaching walls to form the roof base. 5) Optional steps to cut out portions of the roof by sketching openings in plan view.

Uploaded by

Amer Gonzales
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 14

Roof By Extrusion

EXAMPLE 1

1) Make a Reference line from Start and to the End.


2) Click Ref. Plane Start and End
Ref line –Roof start

Ref line –Roof end

3)Click the Ref. Plane & Name it From Start & End

Page 1 of 14
CREATING THE ROOF BY EXTRUSION

3) Click Architecture-Roof by Extrusion

4) Specify the New Work Plane


Click Name –Reference Plane:Roof Start - OK

5) Click Elevation View: West then Open View


(From Start is in the Elevation West)

Page 2 of 14
6) Elevation West is displayed then switch to Level 1 where the Roof to be extruded.
Click OK

7) Revit now is in the Sketch mode & draw the profile using the Draw Pallette.

8) Draw the Curve using Arc.

9) Assign Roof type in the Properties and Duplicate and edit the properties.
10) Click Finish mode

11)Drag the Grip to the End Roof Ref line.

Page 3 of 14
11) Select all the drawing and filter.

12) Uncheck Roof and OK

Page 4 of 14
13) Attach Top Base – Select Roof as the Top Base

After attaching:

Page 5 of 14
CREATING CUTOUT IN THE ROOF

14) Go to Plan View and select the Roof created

15) Click Vertical Opening

16) Set the Transparency or Wire frame of the Roof

Page 6 of 14
17) Start creating Lines using Draw Palette

18) Click the Finish mode after finish sketching.

Finish

Page 7 of 14
EXAMPLE 2

1) Create a Floor Plan as per below

Page 8 of 14
2) Make 2 Reference Line (Roof Start And Roof End)

3) Click Architecture-Roof by Extrusion


4) Click Name and make Roof Start as a Reference plane –Click OK

Page 9 of 14
5) To Make a Sketch Go to Elevation View – West
Then open View

6) Roof Reference Level and offset – Level 2 then Click OK

7) Start sketch by using the Draw Pallette.


Click Finish mode

Page 10 of 14
8) Go to 3D View, Select All and Filter

9) Select/check only wall


10) Click Attach Top Base
(Wall to be attached in the Roof)

Page 11 of 14
11) Click the Roof

12) CUTOUT
Goto Plan View(Level 3) to make a cut out.

Page 12 of 14
13) Click the Roof & Vertical Opening to make a cutout

14) Make a cuout using Draw Palette and Click Finish mode

Page 13 of 14
Page 14 of 14

You might also like