Parameters Page 1 of 14

Parameters and Signals

ACS800 democase default parameters

File:
ACS800_democase_default_parameters
Properties

Control Board Type RMIO

Kind ACS800
Name ACS 800 DEMO
Product Family ACS 800 DEMO
System software version 4.200

Application

Base library FFFFF.002

Name ASARF018
Version 11-06-14 12:34:48:546

Parameters and Signals

01: ACTUAL SIGNALS

Name Value
01.01: PROCESS VARIABLE [%] 0.0
01.02: SPEED [rpm] 0.0
01.03: FREQUENCY [Hz] 0.00
01.04: CURRENT [A] 0.00
01.05: TORQUE [%] 0.00
01.06: POWER [%] 0.00
01.07: DC BUS VOLTAGE V [V] 652.1
01.08: MAINS VOLTAGE [V] 415.0
01.09: OUTPUT VOLTAGE [V] 0.0
01.10: ACS800 TEMP [%] 32.7
01.11: EXTERNAL REF 1 [rpm] 0.0
01.12: EXTERNAL REF 2 [%] 0.0
01.13: CTRL LOCATION LOCAL
01.14: OP HOUR COUNTER [h] 9.57
01.15: KILOWATT HOURS [kWh] 0.0
01.16: APPL BLOCK OUTPUT [%] 0.0
01.17: DI6-1 STATUS 0000000b
01.18: AI1 [V] -3.9
01.19: AI2 [mA] 15.6
01.20: AI3 [mA] 11.2
01.21: RO3-1 STATUS 0000101b
01.22: AO1 [mA] 0.0
01.23: AO2 [mA] 0.0
01.24: ACTUAL VALUE 1 [%] 0.0
01.25: ACTUAL VALUE 2 [%] 0.0

file://C:\Users\fitehei\AppData\Local\Temp\Parameters.xml 17.10.2012
Parameters Page 2 of 14

01.26: CONTROL DEVIATION [%] 0.0

01.27: APPLICATION MACRO FACTORY
01.28: EXT AO1 [mA] 0.0
01.29: EXT AO2 [mA] 0.0
01.30: PP 1 TEMP [C] 30.9
01.31: PP 2 TEMP [C] 0.0
01.32: PP 3 TEMP [C] 0.0
01.33: PP 4 TEMP [C] 0.0
01.34: ACTUAL VALUE [%] 0.0
01.35: MOTOR 1 TEMP [C] 0.0
01.36: MOTOR 2 TEMP [C] 0.0
01.37: MOTOR TEMP EST [C] 30.0
01.38: AI5 [mA] 0.0
01.39: AI6 [mA] 0.0
01.40: DI7-12 STATUS 0000000b
01.41: EXT RO STATUS 0000001b
01.42: PROCESS SPEED REL [%] 0.0
01.43: MOTOR RUN TIME [h] 0.80
01.44: FAN ON-TIME [h] 2.67
01.45: CTRL BOARD TEMP [C] 40
01.46: SAVED KWH [kWh] 0.1
01.47: SAVED GWH [GWh] 0
01.48: SAVED AMOUNT [EUR] 0.0
01.49: SAVED AMOUNT M [MEU] 0
01.50: SAVED CO2 [kg] 0.0
01.51: SAVED CO2 KTON [kt] 0

02: ACTUAL SIGNALS

Name Value
02.01: SPEED REF 2 [rpm] 0
02.02: SPEED REF 3 [rpm] 0
02.09: TORQUE REF 2 [%] 0.00
02.10: TORQUE REF 3 [%] 0.00
02.13: TORQ USED REF [%] 0.00
02.14: FLUX REF [%] 100
02.17: SPEED ESTIMATED [rpm] 0.0
02.18: SPEED MEASURED [rpm] 0.00
02.19: MOTOR ACCELERATIO [rpm/s] 0.0
02.20: USER CURRENT [%] 0.0

03: ACTUAL SIGNALS

Name Value
03.01: MAIN CTRL WORD 477h
03.02: MAIN STATUS WORD 1033h
03.03: AUX STATUS WORD 1880h
03.04: LIMIT WORD 1 0h
03.05: FAULT WORD 1 0h
03.06: FAULT WORD 2 0h
03.07: SYSTEM FAULT 0h
03.08: ALARM WORD 1 0h
03.09: ALARM WORD 2 0h
03.11: FOLLOWER MCW 0h
03.13: AUX STATUS WORD 3 700h

file://C:\Users\fitehei\AppData\Local\Temp\Parameters.xml 17.10.2012
Parameters Page 3 of 14

03.14: AUX STATUS WORD 4 0h

03.15: FAULT WORD 4 0h
03.16: ALARM WORD 4 0h
03.17: FAULT WORD 5 0h
03.18: ALARM WORD 5 0h
03.19: INT INIT FAULT 0h
03.20: LATEST FAULT 5300h
03.21: 2.LATEST FAULT 0h
03.22: 3.LATEST FAULT 0h
03.23: 4.LATEST FAULT 0h
03.24: 5.LATEST FAULT 0h
03.25: LATEST WARNING FF69h
03.26: 2.LATEST WARNING FF33h
03.27: 3.LATEST WARNING FF32h
03.28: 4.LATEST WARNING 0h
03.29: 5.LATEST WARNING FF34h
03.30: LIMIT WORD INV 0h
03.31: ALARM WORD 6 0h
03.32: EXT IO STATUS 0h
03.33: FAULT WORD 6 0h

04: ACTUAL SIGNALS

Name Value
04.01: FAULTED INT INFO 0h
04.02: INT SC INFO 0h

09: ACTUAL SIGNALS

Name Value
09.01: AI1 SCALED -7800
09.02: AI2 SCALED 15616
09.03: AI3 SCALED 11193
09.04: AI5 SCALED 0
09.05: AI6 SCALED 0
09.06: DS MCW 0h
09.07: MASTER REF1 0
09.08: MASTER REF2 0
09.09: AUX DS VAL1 0
09.10: AUX DS VAL2 0
09.11: AUX DS VAL3 0
09.12: LCU ACT SIGNAL1 0
09.13: LCU ACT SIGNAL2 0

10: START/STOP/DIR

Name Value
10.01: EXT1 STRT/STP/DIR DI1,2
10.02: EXT2 STRT/STP/DIR NOT SEL
10.03: REF DIRECTION FORWARD
10.04: EXT 1 STRT PTR +.000.000.00
10.05: EXT 2 STRT PTR +.000.000.00
10.06: JOG SPEED SELECT NOT SEL
10.07: NET CONTROL <Read-protected>
10.08: NET REFERENCE <Read-protected>

file://C:\Users\fitehei\AppData\Local\Temp\Parameters.xml 17.10.2012
Parameters Page 4 of 14

10.09: SLS ACTIVE NO

11: REFERENCE SELECT

Name Value
11.01: KEYPAD REF SEL REF1 (rpm)
11.02: EXT1/EXT2 SELECT EXT1
11.03: EXT REF1 SELECT AI1
11.04: EXT REF1 MINIMUM [rpm] 0
11.05: EXT REF1 MAXIMUM [rpm] 1500
11.06: EXT REF2 SELECT KEYPAD
11.07: EXT REF2 MINIMUM [%] 0
11.08: EXT REF2 MAXIMUM [%] 100
11.09: EXT 1/2 SEL PTR +.000.000.00
11.10: EXT 1 REF PTR +.000.000.00
11.11: EXT 2 REF PTR +.000.000.00

12: CONSTANT SPEEDS

Name Value
12.01: CONST SPEED SEL DI5,6
12.02: CONST SPEED 1 [rpm] 300
12.03: CONST SPEED 2 [rpm] 600
12.04: CONST SPEED 3 [rpm] 900
12.05: CONST SPEED 4 [rpm] 300
12.06: CONST SPEED 5 [rpm] 0
12.07: CONST SPEED 6 [rpm] 0
12.08: CONST SPEED 7 [rpm] 0
12.09: CONST SPEED 8 [rpm] 0
12.10: CONST SPEED 9 [rpm] 0
12.11: CONST SPEED 10 [rpm] 0
12.12: CONST SPEED 11 [rpm] 0
12.13: CONST SPEED 12 [rpm] 0
12.14: CONST SPEED 13 [rpm] 0
12.15: CONST SPEED 14 [rpm] 0
12.16: CONST SPEED 15 [rpm] 0

13: ANALOGUE INPUTS

Name Value
13.01: MINIMUM AI1 0V
13.02: MAXIMUM AI1 10 V
13.03: SCALE AI1 [%] 100.0
13.04: FILTER AI1 [s] 0.10
13.05: INVERT AI1 NO
13.06: MINIMUM AI2 0 mA
13.07: MAXIMUM AI2 20 mA
13.08: SCALE AI2 [%] 100.0
13.09: FILTER AI2 [s] 0.10
13.10: INVERT AI2 NO
13.11: MINIMUM AI3 0 mA
13.12: MAXIMUM AI3 20 mA
13.13: SCALE AI3 [%] 100.0
13.14: FILTER AI3 [s] 0.10
13.15: INVERT AI3 NO

file://C:\Users\fitehei\AppData\Local\Temp\Parameters.xml 17.10.2012
Parameters Page 5 of 14

13.16: MINIMUM AI5 0 mA

13.17: MAXIMUM AI5 20 mA
13.18: SCALE AI5 [%] 100.0
13.19: FILTER AI5 [s] 0.10
13.20: INVERT AI5 NO
13.21: MINIMUM AI6 0 mA
13.22: MAXIMUM AI6 20 mA
13.23: SCALE AI6 [%] 100.0
13.24: FILTER AI6 [s] 0.10
13.25: INVERT AI6 NO

14: RELAY OUTPUTS

Name Value
14.01: RELAY RO1 OUTPUT READY
14.02: RELAY RO2 OUTPUT RUNNING
14.03: RELAY RO3 OUTPUT FAULT(-1)
14.04: RO1 TON DELAY [s] 0.0
14.05: RO1 TOFF DELAY [s] 0.0
14.06: RO2 TON DELAY [s] 0.0
14.07: RO2 TOFF DELAY [s] 0.0
14.08: RO3 TON DELAY [s] 0.0
14.09: RO3 TOFF DELAY [s] 0.0
14.10: DIO MOD1 RO1 READY
14.11: DIO MOD1 RO2 RUNNING
14.12: DIO MOD2 RO1 FAULT
14.13: DIO MOD2 RO2 WARNING
14.14: DIO MOD3 RO1 REF 2 SEL
14.15: DIO MOD3 RO2 AT SPEED
14.16: RO PTR1 +.000.000.00
14.17: RO PTR2 +.000.000.00
14.18: RO PTR3 +.000.000.00
14.19: RO PTR4 +.000.000.00
14.20: RO PTR5 +.000.000.00
14.21: RO PTR6 +.000.000.00
14.22: RO PTR7 +.000.000.00
14.23: RO PTR8 +.000.000.00
14.24: RO PTR9 +.000.000.00

15: ANALOGUE OUTPUTS

Name Value
15.01: ANALOGUE OUTPUT1 SPEED
15.02: INVERT AO1 NO
15.03: MINIMUM AO1 0 mA
15.04: FILTER AO1 [s] 0.10
15.05: SCALE AO1 [%] 100
15.06: ANALOGUE OUTPUT2 CURRENT
15.07: INVERT AO2 NO
15.08: MINIMUM AO2 0 mA
15.09: FILTER AO2 [s] 2.00
15.10: SCALE AO2 [%] 100
15.11: AO1 PTR +.000.000.00
15.12: AO2 PTR +.000.000.00

file://C:\Users\fitehei\AppData\Local\Temp\Parameters.xml 17.10.2012
Parameters Page 6 of 14

16: SYST CTRL INPUTS

Name Value
16.01: RUN ENABLE YES
16.02: PARAMETER LOCK OPEN
16.03: PASS CODE 0
16.04: FAULT RESET SEL NOT SEL
16.05: USER MACRO IO CHG NOT SEL
16.06: LOCAL LOCK OFF
16.07: PARAMETER SAVE DONE
16.08: RUN ENA PTR +.000.000.00
16.09: CTRL BOARD SUPPLY INTERNAL 24V
16.10: ASSISTANT SEL ON
16.11: FAULT RESET PTR +.000.000.00
16.12: RESET COUNTER NO

20: LIMITS

Name Value
20.01: MINIMUM SPEED [rpm] -1500
20.02: MAXIMUM SPEED [rpm] 1500
20.03: MAXIMUM CURRENT [A] 2.2
20.04: TORQ MAX LIM1 [%] 300.0
20.05: OVERVOLTAGE CTRL ON
20.06: UNDERVOLTAGE CTRL ON
20.07: MINIMUM FREQ [Hz] <Read-protected>
20.08: MAXIMUM FREQ [Hz] <Read-protected>
20.11: P MOTORING LIM [%] 300.0
20.12: P GENERATING LIM [%] -300.0
20.13: MIN TORQ SEL NEG MAX TORQ
20.14: MAX TORQ SEL MAX LIM1
20.15: TORQ MIN LIM1 [%] 0.0
20.16: TORQ MIN LIM2 [%] 0.0
20.17: TORQ MAX LIM2 [%] 300.0
20.18: TORQ MIN PTR +.000.000.00
20.19: TORQ MAX PTR +.000.000.00
20.20: MIN AI SCALE [%] 0.0
20.21: MAX AI SCALE [%] 300.0
20.22: SLS SPEED LIMIT [rpm] 0

21: START/STOP

Name Value
21.01: START FUNCTION AUTO
21.02: CONST MAGN TIME [ms] 500.0
21.03: STOP FUNCTION COAST
21.04: DC HOLD NO
21.05: DC HOLD SPEED [rpm] 5
21.06: DC HOLD CURR [%] 30.0
21.07: RUN ENABLE FUNC COAST STOP
21.08: SCALAR FLYSTART <Read-protected>
21.09: START INTRL FUNC OFF2 STOP
21.10: ZERO SPEED DELAY [s] 0.50

22: ACCEL/DECEL

file://C:\Users\fitehei\AppData\Local\Temp\Parameters.xml 17.10.2012
Parameters Page 7 of 14

Name Value
22.01: ACC/DEC SEL DI4
22.02: ACCEL TIME 1 [s] 20.00
22.03: DECEL TIME 1 [s] 20.00
22.04: ACCEL TIME 2 [s] 60.00
22.05: DECEL TIME 2 [s] 60.00
22.06: ACC/DEC RAMP SHPE [s] 0.00
22.07: EM STOP RAMP TIME [s] 3.00
22.08: ACC PTR +.000.000.00
22.09: DEC PTR +.000.000.00
22.10: SLS ACCELER TIME [s] 20.00
22.11: SLS DECELER TIME [s] 20.00

23: SPEED CTRL

Name Value
23.01: GAIN 10.0
23.02: INTEGRATION TIME [s] 2.50
23.03: DERIVATION TIME [ms] 0.0
23.04: ACC COMPENSATION [s] 0.00
23.05: SLIP GAIN [%] 100.0
23.06: AUTOTUNE RUN NO
23.07: SP ACT FILT TIME [ms] 8.0

25: CRITICAL SPEEDS

Name Value
25.01: CRIT SPEED SELECT OFF
25.02: CRIT SPEED 1 LOW [rpm] 0
25.03: CRIT SPEED 1 HIGH [rpm] 0
25.04: CRIT SPEED 2 LOW [rpm] 0
25.05: CRIT SPEED 2 HIGH [rpm] 0
25.06: CRIT SPEED 3 LOW [rpm] 0
25.07: CRIT SPEED 3 HIGH [rpm] 0

26: MOTOR CONTROL

Name Value
26.01: FLUX OPTIMIZATION NO
26.02: FLUX BRAKING YES
26.03: IR-COMPENSATION [%] <Read-protected>
26.04: IR STEP UP FREQ [Hz] <Read-protected>
26.05: HEX FIELD WEAKEN OFF
26.06: FLUX REF PTR C. 10000
26.07: FLYSTART CUR REF [%] 50
26.08: FLYSTART INIT DLY 25
26.09: FS METHOD OFF

27: BRAKE CHOPPER

Name Value
27.01: BRAKE CHOPPER CTL OFF
27.02: BR OVERLOAD FUNC NO
27.03: BR RESISTANCE [Ohm] 100.00

file://C:\Users\fitehei\AppData\Local\Temp\Parameters.xml 17.10.2012
Parameters Page 8 of 14

27.04: BR THERM T CONST [s] 0.000

27.05: MAX CONT BR POWER [kW] 0.00
27.06: BC CTRL MODE COMMON DC

30: FAULT FUNCTIONS

Name Value
30.01: AI<MIN FUNCTION FAULT
30.02: PANEL LOSS FAULT
30.03: EXTERNAL FAULT NOT SEL
30.04: MOTOR THERM PROT NO
30.05: MOT THERM P MODE DTC
30.06: MOTOR THERM TIME [s] 1258.9
30.07: MOTOR LOAD CURVE [%] 100.0
30.08: ZERO SPEED LOAD [%] 74.0
30.09: BREAK POINT [Hz] 45.0
30.10: STALL FUNCTION FAULT
30.11: STALL FREQ HI [Hz] 20.0
30.12: STALL TIME [s] 20.00
30.13: UNDERLOAD FUNC NO
30.14: UNDERLOAD TIME [s] 600
30.15: UNDERLOAD CURVE 1
30.16: MOTOR PHASE LOSS NO
30.17: EARTH FAULT FAULT
30.18: COMM FLT FUNC FAULT
30.19: MAIN REF DS T-OUT [s] 3.00
30.20: COMM FLT RO/AO ZERO
30.21: AUX DS T-OUT [s] 3.00
30.22: IO CONFIG FUNC WARNING
30.23: LIMIT WARNING 0000000b

31: AUTOMATIC RESET

Name Value
31.01: NUMBER OF TRIALS 0
31.02: TRIAL TIME [s] 30.0
31.03: DELAY TIME [s] 0.0
31.04: OVERCURRENT NO
31.05: OVERVOLTAGE NO
31.06: UNDERVOLTAGE NO
31.07: AI SIGNAL<MIN NO
31.08: LINE CONV NO

32: SUPERVISION

Name Value
32.01: SPEED1 FUNCTION NO
32.02: SPEED1 LIMIT [rpm] 0
32.03: SPEED2 FUNCTION NO
32.04: SPEED2 LIMIT [rpm] 0
32.05: CURRENT FUNCTION NO
32.06: CURRENT LIMIT [A] 0
32.07: TORQUE1 FUNCTION NO
32.08: TORQUE1 LIMIT [%] 0
32.09: TORQUE2 FUNCTION NO

file://C:\Users\fitehei\AppData\Local\Temp\Parameters.xml 17.10.2012
Parameters Page 9 of 14

32.10: TORQUE2 LIMIT [%] 0

32.11: REF1 FUNCTION NO
32.12: REF1 LIMIT [rpm] 0
32.13: REF2 FUNCTION NO
32.14: REF2 LIMIT [%] 0
32.15: ACT1 FUNCTION NO
32.16: ACT1 LIMIT [%] 0
32.17: ACT2 FUNCTION NO
32.18: ACT2 LIMIT [%] 0

33: INFORMATION

Name Value
33.01: SOFTWARE VERSION AS7R7365
33.02: APPL SW VERSION ASARF018
33.03: TEST DATE 0h
33.04: BOARD TYPE RMIO - 0X

34: PROCESS VARIABLE

Name Value
34.01: SCALE 100.00
34.02: P VAR UNIT %
34.03: SELECT P VAR 142
34.04: MOTOR SP FILT TIM [ms] 500
34.05: TORQ ACT FILT TIM [ms] 100
34.06: RESET RUN TIME NO

35: MOT TEMP MEAS

Name Value
35.01: MOT1 TEMP AI1 SEL NOT IN USE
35.02: MOT 1 TEMP ALM L [C] 110
35.03: MOT 1 TEMP FLT L [C] 130
35.04: MOT2 TEMP AI2 SEL NOT IN USE
35.05: MOT 2 TEMP ALM L [C] 110
35.06: MOT 2 TEMP FLT L [C] 130
35.07: MOT MOD COMPENSAT YES
35.08: MOT MOD COMP PTR +.000.000.00

40: PID CONTROL

Name Value
40.01: PID GAIN 1.0
40.02: PID INTEG TIME [s] 60.00
40.03: PID DERIV TIME [s] 0.00
40.04: PID DERIV FILTER [s] 1.00
40.05: ERROR VALUE INV NO
40.06: ACTUAL VALUE SEL ACT1
40.07: ACTUAL1 INPUT SEL AI2
40.08: ACTUAL2 INPUT SEL AI2
40.09: ACT1 MINIMUM [%] 0
40.10: ACT1 MAXIMUM [%] 100
40.11: ACT2 MINIMUM [%] 0

file://C:\Users\fitehei\AppData\Local\Temp\Parameters.xml 17.10.2012
Parameters Page 10 of 14

40.12: ACT2 MAXIMUM [%] 100

40.13: PID INTEGRATION ON
40.14: TRIM MODE OFF
40.15: TRIM REF SEL AI1
40.16: TRIM REFERENCE [%] 0.0
40.17: TRIM RANGE ADJUST [%] 100.0
40.18: TRIM SELECTION SPEED TRIM
40.19: ACTUAL FILT TIME [s] 0.04
40.20: SLEEP SELECTION <Read-protected>
40.21: SLEEP LEVEL [rpm] <Read-protected>
40.22: SLEEP DELAY [s] <Read-protected>
40.23: WAKE UP LEVEL [%] <Read-protected>
40.24: WAKE UP DELAY [s] <Read-protected>
40.25: ACTUAL1 PTR +.000.000.00
40.26: PID MINIMUM [%] -100.0
40.27: PID MAXIMUM [%] 100.0
40.28: TRIM REF PTR +.000.000.00

42: BRAKE CONTROL

Name Value
42.01: BRAKE CTRL OFF
42.02: BRAKE ACKNOWLEDGE OFF
42.03: BRAKE OPEN DELAY [s] 0.0
42.04: BRAKE CLOSE DELAY [s] 0.0
42.05: ABS BRAKE CLS SPD [RPM] 10
42.06: BRAKE FAULT FUNC FAULT
42.07: STRT TORQ REF SEL NO
42.08: START TORQ REF [%] 0.0
42.09: EXTEND RUN T [s] 0.0
42.10: LOW REF BRK HOLD [s] 0.0

45: ENERGY OPT

Name Value
45.02: ENERGY TARIFF1 [c/E] 0.000
45.06: E TARIFF UNIT EUR
45.08: PUMP REF POWER [%] 100.00
45.09: ENERGY RESET DONE

52: STANDARD MODBUS

Name Value
52.01: STATION NUMBER 1
52.02: BAUDRATE 9600
52.03: PARITY ODD

60: MASTER/FOLLOWER

Name Value
60.01: MASTER LINK MODE NOT IN USE
60.02: TORQUE SELECTOR <Read-protected>
60.03: WINDOW SEL ON <Read-protected>
60.04: WINDOW WIDTH POS [rpm] <Read-protected>

file://C:\Users\fitehei\AppData\Local\Temp\Parameters.xml 17.10.2012
Parameters Page 11 of 14

60.05: WINDOW WIDTH NEG [rpm] <Read-protected>

60.06: DROOP RATE [%] 0.0
60.07: MASTER SIGNAL 2 202
60.08: MASTER SIGNAL 3 213

70: DDCS CONTROL

Name Value
70.01: CHANNEL 0 ADDR 1
70.02: CHANNEL 3 ADDR 1
70.03: CH1 BAUD RATE 4 Mbit/s
70.04: CH0 DDCS HW CONN RING
70.05: CH2 DDCS HW CONN RING

72: USER LOAD CURVE

Name Value
72.01: OVERLOAD FUNCTION NO
72.02: LOAD CURRENT1 [%] 500.0
72.03: LOAD CURRENT2 [%] 500.0
72.04: LOAD CURRENT3 [%] 500.0
72.05: LOAD CURRENT4 [%] 500.0
72.06: LOAD CURRENT5 [%] 500.0
72.07: LOAD CURRENT6 [%] 500.0
72.08: LOAD CURRENT7 [%] 500.0
72.09: LOAD CURRENT8 [%] 500.0
72.10: LOAD FREQ1 [%] 0.0
72.11: LOAD FREQ2 [%] 20.0
72.12: LOAD FREQ3 [%] 40.0
72.13: LOAD FREQ4 [%] 60.0
72.14: LOAD FREQ5 [%] 80.0
72.15: LOAD FREQ6 [%] 100.0
72.16: LOAD FREQ7 [%] 130.0
72.17: LOAD FREQ8 [%] 150.0
72.18: LOAD CURRENT LIM [%] 500.0
72.19: LOAD THERMAL TIME [s] 1.0
72.20: LOAD COOLING TIME [s] 1

83: ADAPT PROG CTRL

Name Value
83.01: ADAPT PROG CMD EDIT
83.02: EDIT COMMAND NO
83.03: EDIT BLOCK 0
83.04: TIMELEVEL SEL 100 ms
83.05: PASSCODE 0

84: ADAPTIVE PROGRAM

Name Value
84.01: STATUS 8h
84.02: FAULTED PAR +.000.000.00
84.05: BLOCK1 NO
84.06: INPUT1 +.000.000.00

file://C:\Users\fitehei\AppData\Local\Temp\Parameters.xml 17.10.2012
Parameters Page 12 of 14

84.07: INPUT2 +.000.000.00

84.08: INPUT3 +.000.000.00
84.09: OUTPUT 0
84.10: BLOCK2 NO
84.11: INPUT1 +.000.000.00
84.12: INPUT2 +.000.000.00
84.13: INPUT3 +.000.000.00
84.14: OUTPUT 0
84.15: BLOCK3 NO
84.16: INPUT1 +.000.000.00
84.17: INPUT2 +.000.000.00
84.18: INPUT3 +.000.000.00
84.19: OUTPUT 0
84.20: BLOCK4 NO
84.21: INPUT1 +.000.000.00
84.22: INPUT2 +.000.000.00
84.23: INPUT3 +.000.000.00
84.24: OUTPUT 0
84.25: BLOCK5 NO
84.26: INPUT1 +.000.000.00
84.27: INPUT2 +.000.000.00
84.28: INPUT3 +.000.000.00
84.29: OUTPUT 0
84.30: BLOCK6 NO
84.31: INPUT1 +.000.000.00
84.32: INPUT2 +.000.000.00
84.33: INPUT3 +.000.000.00
84.34: OUTPUT 0
84.35: BLOCK7 NO
84.36: INPUT1 +.000.000.00
84.37: INPUT2 +.000.000.00
84.38: INPUT3 +.000.000.00
84.39: OUTPUT 0
84.40: BLOCK8 NO
84.41: INPUT1 +.000.000.00
84.42: INPUT2 +.000.000.00
84.43: INPUT3 +.000.000.00
84.44: OUTPUT 0
84.45: BLOCK9 NO
84.46: INPUT1 +.000.000.00
84.47: INPUT2 +.000.000.00
84.48: INPUT3 +.000.000.00
84.49: OUTPUT 0
84.50: BLOCK10 NO
84.51: INPUT1 +.000.000.00
84.52: INPUT2 +.000.000.00
84.53: INPUT3 +.000.000.00
84.54: OUTPUT 0
84.55: BLOCK11 NO
84.56: INPUT1 +.000.000.00
84.57: INPUT2 +.000.000.00
84.58: INPUT3 +.000.000.00
84.59: OUTPUT 0
84.60: BLOCK12 NO
84.61: INPUT1 +.000.000.00
84.62: INPUT2 +.000.000.00

file://C:\Users\fitehei\AppData\Local\Temp\Parameters.xml 17.10.2012
Parameters Page 13 of 14

+.000.000.00
84.64: OUTPUT 0
84.65: BLOCK13 NO
84.66: INPUT1 +.000.000.00
84.67: INPUT2 +.000.000.00
84.68: INPUT3 +.000.000.00
84.69: OUTPUT 0
84.70: BLOCK14 NO
84.71: INPUT1 +.000.000.00
84.72: INPUT2 +.000.000.00
84.73: INPUT3 +.000.000.00
84.74: OUTPUT 0
84.75: BLOCK15 NO
84.76: INPUT1 +.000.000.00
84.77: INPUT2 +.000.000.00
84.78: INPUT3 +.000.000.00
84.79: OUTPUT 0

85: USER CONSTANTS

Name Value
85.01: CONSTANT1 0
85.02: CONSTANT2 0
85.03: CONSTANT3 0
85.04: CONSTANT4 0
85.05: CONSTANT5 0
85.06: CONSTANT6 0
85.07: CONSTANT7 0
85.08: CONSTANT8 0
85.09: CONSTANT9 0
85.10: CONSTANT10 0
85.11: STRING1 MESSAGE1
85.12: STRING2 MESSAGE2
85.13: STRING3 MESSAGE3
85.14: STRING4 MESSAGE4
85.15: STRING5 MESSAGE5

90: D SET REC ADDR

Name Value
90.01: AUX DS REF3 0
90.02: AUX DS REF4 0
90.03: AUX DS REF5 0
90.04: MAIN DS SOURCE 1
90.05: AUX DS SOURCE 3

92: D SET TR ADDR

Name Value
92.02: MAIN DS ACT1 102
92.03: MAIN DS ACT2 105
92.04: AUX DS ACT3 305
92.05: AUX DS ACT4 308
92.06: AUX DS ACT5 306
92.07: MSW B10 PTR +.003.014.09

file://C:\Users\fitehei\AppData\Local\Temp\Parameters.xml 17.10.2012
Parameters Page 14 of 14

92.08: MSW B13 PTR +.000.000.00

92.09: MSW B14 PTR +.000.000.00

95: HARDWARE SPECIF

Name Value
95.01: FAN SPD CTRL MODE CONTROLLED
95.02: FUSE SWITCH CTRL OFF
95.03: INT CONFIG USER 1
95.04: EX/SIN REQUEST NO
95.05: ENA INC SW FREQ <Read-protected>
95.06: LCU Q PW REF 0
95.07: LCU DC REF 0
95.08: LCU PAR1 SEL 106
95.09: LCU PAR2 SEL 110
95.10: TEMP INV AMBIENT [C] 40.0
95.11: SUPPLY CTRL MODE NONE
95.12: LCU RUN PTR +.000.000.00

98: OPTION MODULES

Name Value
98.01: ENCODER MODULE NO
98.02: COMM. MODULE LINK NO
98.03: DI/O EXT MODULE 1 NO
98.04: DI/O EXT MODULE 2 NO
98.05: DI/O EXT MODULE 3 NO
98.06: AI/O EXT MODULE NO
98.07: COMM PROFILE ABB DRIVES
98.09: DI/O EXT1 DI FUNC DI7,8,9
98.10: DI/O EXT2 DI FUNC DI10,11,12
98.11: DI/O EXT3 DI FUNC DI11,12
98.12: AI/O MOTOR TEMP NO
98.13: AI/O EXT AI1 FUNC UNIPOLAR AI5
98.14: AI/O EXT AI2 FUNC UNIPOLAR AI6
98.16: SIN FILT SUPERV <Read-protected>

99: START-UP DATA

Name Value
99.01: LANGUAGE ENGLISH
99.02: APPLICATION MACRO FACTORY
99.03: APPLIC RESTORE NO
99.04: MOTOR CTRL MODE DTC
99.05: MOTOR NOM VOLTAGE [V] 220
99.06: MOTOR NOM CURRENT [A] 1.3
99.07: MOTOR NOM FREQ [Hz] 50.00
99.08: MOTOR NOM SPEED [rpm] 1380
99.09: MOTOR NOM POWER [kW] 0.2
99.10: MOTOR ID RUN MODE ID MAGN
99.11: DEVICE NAME

file://C:\Users\fitehei\AppData\Local\Temp\Parameters.xml 17.10.2012