Total No. of Questions : 9] SEAT No.

P3345 [Total No. of Pages : 3

[5353]-515

5
3:0
T.E. (Mechanical)

3:5
METROLOGY AND QUALITY CONTROL

81
5/2 1
9
(2015 Pattern)

01
Time : 2½ Hours]
8 1 30 [Max. Marks : 70
.23 01
4/0
Instructions to the candidates:
P
1) Answer Q1 or Q2, Q3 or Q4, Q5 or Q6, Q7 or Q8.
8.2 G

2) Neat diagram must be drawn wherever necessary.

.24 CE

3) Assume Suitable data if necessary.

16

4) Use of Calculator is allowed.

5
5) Figures to the right indicate full marks.

3:0
49

3:5
Q1) a) Differentiate between Precision & Accuracy with Suitable examples. [5]
81
91
01
b) Draw a neat sketch of micrometer & how to calculate least count of
30
5/2

micrometer, give one example. [5]

01
4/0

OR
GP
81

Q2) a) a) Explain any one method of assessing the surface finish. [5]
.23
CE

b) Explain tool makers microscope & their application. [5]

16
8.2

5
.24

3:0
Q3) a) Explain laser interferometer & its application. [5]
49

3:5

b) Write short note on machine vision system. [5]

81
91

OR
01
30
5/2

Q4) a) State & Explain Taylor’s principle of gauge design with example. [5]
01
4/0

b) Explain method of measuring effective diameter using two wires with neat
GP
81

sketch. [5]
.23
CE
16
8.2

Q5) a) Explain Jurans triology approach with diagram. [8]

.24

b) State seven new quality tools. Explain any three in detail. [8]
49

OR
P.T.O.
Q6) a) What is cost of quality? Explain Cost of failure, Cost of appraisal &
cost of prevention. [8]
b) What is initial planning for quality? Explain in details. [8]

5
3:0
3:5
Q7) a) What are advantages of sampling inspection over 100% inspection?

81
5/2 1
Explain the difference between single sampling & double sampling plan.

9
01
[8]
b) 8 1 30
Following is the record for successive lots of part being produced by
.23 01
4/0
plastic molding press. As each lot is come off the line a random sample
P

of 150 pieces were inspected (results are expressed to the nearest 0.1%)
8.2 G

Calculate p, Control limits & plot control chart and comment. [8]
.24 CE
16

Lot no Sample size No. of defectives

1 150 4

5
3:0
2 150 8
49

3:5
3 150 2
81
91
4 150 4
01
30
5/2

5 150 4
01
4/0

6 150 6
GP
81

7 150 10
.23
CE

8 150 4
16
8.2

9 150 6
5
.24

3:0
10 150 8
49

3:5

OR
81
91

Q8) a) Write short note on OC curve & its characteristics. [8]

01
30

b) Explain single sampling plan with flow chart. For the given data
5/2
01

calculate sample size and AOQ for single sampling plan [8]
4/0

i) Probability of acceptance for 0.3% defectives in a lot is 0.558

GP
81

ii) Lot size N = 10000 units

.23
CE
16

iii) np’ = 1.5

8.2

iv) Acceptance number c = 1

.24

v) Defectives found in the sample are not to be replaced

49

[5353]-515 2
 e)
a)

c)

d)
b)

[5353]-515
49
Kanban

.24 CE FMECA

TS-16949
8.2 G
16 P
Zero defects

Quality Audit
.23 01
8 1 30
4/0 9
5/2 1
49
.24 CE 01
Q9) Write short note on (Any three) :

8.2 GP 81
16 3:5

3
.23 01 3:0
81 30 5
4/0 91 eee
49 5/2
.24 CE 01
8.2 GP 81
16 3:5
.23 01 3:0
81 30 5
4/0 91
5/2
01
81
3:5
3:0
5
[18]