Automobile Transmission & Mechanism Course Code: 3330202

GUJARAT TECHNOLOGICAL UNIVERSITY, AHMEDABAD, GUJARAT

Course Curriculum

AUTOMOBILE TRANSMISSION & MECHANISMS

(Code: 3330202)

Diploma Programme in which this course is offered Semester in which offered

Automobile Engineering 3rd Semester

1. RATIONALE
Any automobile apart from engine is made of transmission system and other systems like
brakes, steering, suspension systems, wheel and tyres. This course provides knowledge about
these systems. This course will also help the students during inspection, installation, operation
and maintenance of transmission, steering and suspension systems of automobiles. This
course is therefore a core course for automobile engineers and they should develop mastery
over it.

COMPETENCIES (Programme Outcomes (POs) According to NBA terminology)

The course content should be taught and with the aim to develop different types of skills so
that students are able to acquire following competencies:

 Install and test automobile power transmission, brakes, steering and suspension
system during manufacturing
 Maintain automobile power transmission, brakes, steering and suspension system
during service

3. TEACHING AND EXAMINATION SCHEME

Teaching Scheme Total Credits Examination Scheme

(In Hours) (L+T+P) Practical Marks
Total Marks
Theory Marks

L T P C ESE PA ESE PA
150
4 0 2 6 70 30 20 30

Legends: L-Lecture; T – Tutorial/Teacher Guided Student Activity; P -Practical; C – Credit;; ESE -End
Semester Examination; PA - Progressive Assessment.

GTU/ NITTTR Bhopal/12-13 Gujarat State

Automobile Transmission & Mechanism Course Code: 3330202

4. DETAILED COURSE CONTENTS

Unit Major Learning Outcomes Topics and Sub-topics
(Course Outcomes in
Cognitive Domain
according to NBA
terminology)
Unit – I 1a. Describe power 1.1 Flow of power transmitted in front wheel
transmission systems. drive, rear wheel drive and four wheel drive.
Introduction to 1b. Draw different layout of 1.2 Different layout of chassis.
Automobile chassis. 1.3 Lubrication of chassis.
Transmission 1c. Explain construction of 1.4 Different types of frame.
System frames. 1.5 Frame less chassis
Unit – II 2a. List different types of 2.1 Necessity Types of clutches.
clutches. 2.2 Construction and functions of different types
Clutch 2b. Explain operation of of clutches, clutch actuating mechanism.
Clutch, Clutch actuating 2.3 Construction and functions of fluid coupling.
Mechanism.
2c. Describe Construction
and working of fluid
coupling.
Unit – III 3a. Describe different types 3.1 Necessity Types of gearboxes.
of gears and gear boxes. 3.2 Construction and functions of Sliding
Gear box 3b. Describe operation of mesh, Constant mesh, Synchromesh,
Gear shifting Epicyclical train & automatic transmission.
mechanisms with line 3.3 Gear shifting mechanism,
diagram of motion flow. 3.4 Torque converter and overdrive- construction
3c. Explain construction & & working.
working of overdrive &
torque convertor.
Unit– IV 4a. Explain need & 4.1 Need of propeller shaft, universal joint and
construction of various slip joint.
Propeller shaft types of propeller shafts. 4.2 Construction & functions of various types of
& universal 4b. Explain construction & propeller shafts.
joint functions of various 4.3 Construction & functions of various types
types of universal joints. of universal joints.
Unit– V 5a. Identify components of 5.1 Necessity of final drive, Types of final
final drive assembly. drive.
Rear axle 5b. Describe construction 5.2 Construction & functions of final drive.
assembly and operation of 5.3 Necessity of differential, Construction &
differential and different functions of differential, differential locks.
types of rear axles. 5.4 Types of axle housing, Function of axle
5c. Describe construction housing and different types of axle
and operation of different mounting.
types of axle housings.
6a. Explain steering 6.1 Necessity of steering geometry.
Unit– VI geometry. 6.2 Kingpin inclination, camber, caster, Toe-in
6b. Describe various steering Toe-out and other terminology.
Front axle and mechanisms with is need 6.3 Types of front axle.
steering and importance. 6.4 Types of steering linkages and Types of
mechanism 6c. Identify various linkages steering gears.
of steering mechanisms, 6.5 Effect of under steer and over steering.
steering gears. 6.6 Steering lock and turning circle radius.
6d. Explain power steering 6.7 Power steering systems- hydraulic,

GTU/ NITTTR Bhopal/12-13 Gujarat State

Automobile Transmission & Mechanism Course Code: 3330202

Unit Major Learning Outcomes Topics and Sub-topics

(Course Outcomes in
Cognitive Domain
according to NBA
terminology)
systems . electronics controlled electrical.
7a. List types of brakes. 7.1 Necessity & Types of brake.
Unit– VII 7b. Explain construction and 7.2 Construction and functions of braking
Brakes operation of various system, Braking Mechanism, Brake setting.
braking mechanisms. 7.3 Anti lock brake systems- purpose,
7c. Explain need, arrangement and function of different parts.
construction & working
of Anti lock brakes.
Unit– VIII 8a. Explain importance of 8.1 Necessity of suspension system.
suspension system. 8.2 Types of front & rear suspension systems.
Suspension 8b. Describe construction 8.3 Types of springs.
system and working of front & 8.4 Construction and functions of various types
rear suspension systems of suspension system.
and shock absorbers. 8.5 Necessity of shock absorber.
8c. Differentiate functions of 8.6 Construction and functions of shock
springs and shock absorber.
absorbers.
Unit– IX 9a. Describe construction of 9.1 Various types of wheels.
various types of wheels 9.2 Salient features of wheels.
Wheels and and tyres. 9.3 Salient features of different types of rims.
tyres 9b. Factors affecting life of 9.4 Types of tyres.
tyre, & Tyre rotation. 9.5 Constructional details of tube and tubeless
9c. Describe tyre rating & tyres.
specifications. 9.6 Hot & cold tyre retrading procedure.
9d. Explain Hot & cold tyre 9.7 Rating of tyre.
retreading procedures. 9.8 Factors affecting life of tyre.
9.9 Tyre rotation and Tyre specification.

5. SUGGESTED SPECIFICATION TABLE WITH HOURS & MARKS (THEORY)

Distribution of Theory Marks

Unit Unit Title Teaching R U A Total
No. Hours Level Level Level
1. Introduction to automobile 04 04 03 00 07
transmission system
2. Clutch 07 02 03 02 07
3. Gear box 09 03 04 03 10
4. Propeller shaft & universal joint 05 02 03 02 07
5. Rear axle assembly 04 02 03 02 07
6. Front axle and steering mechanism 07 02 03 02 07
7. Brakes 10 03 04 04 11
8. Suspension system 05 02 03 02 07
9. Wheels and tyres 05 02 03 02 07
Total 56 22 29 19 70
Legends: R = Remember; U= Understand; A= Apply and above levels (Revised Bloom’s taxonomy

GTU/ NITTTR Bhopal/12-13 Gujarat State

Automobile Transmission & Mechanism Course Code: 3330202

Note: This specification table shall be treated as a general guideline for students and teachers. The
actual distribution of marks in the question paper may vary slightly from above table.

6. SUGGESTED LIST OF PRACTICAL/EXERCISES

The practical/exercises should be properly designed and implemented with an attempt to develop
different types of practical skills (Course Outcomes in psychomotor and affective domain) so that
students are able to acquire the competencies (Programme Outcomes). Following is the list of practical
exercises for guidance.

Note: Here only Course Outcomes in psychomotor domain are listed as practical/exercises. However,
if these practical/exercises are completed appropriately, they would also lead to development of
Programme Outcomes/Course Outcomes in affective domain as given in a common list at the
beginning of curriculum document for this programme. Faculty should refer to that common list and
should ensure that students also acquire those Programme Outcomes/Course Outcomes related to
affective domain.

Apprx. Hrs.
Sr. Unit Practical Exercise (Any Seven) (Course Outcomes in Required
No. No. Psychomotor Domain according to NBA terminology)

1 II Demonstrate construction and working of different types of 4

clutch.
4
2 III Demonstrate construction and working of different types of
gear boxes.
4
3 III Study working principal of overdrive mechanism.
4
4 IV Demonstrate functions of propeller shaft and universal joint.
4
5 V Demonstrate working of differential.
4
6 VII Demonstrate operation of brake mechanisms and brakes
(Hydraulic, Mechanical, Air brake).
4
7 VI Demonstrate construction and operation of steering
mechanism.
4
8 V Demonstrate construction and operation of power steering.
4
9 VIII Demonstrate of different types of suspension systems and
shock absorbers.
4
10 IX Study of different types of wheels and tyres.
28
Total

GTU/ NITTTR Bhopal/12-13 Gujarat State

Automobile Transmission & Mechanism Course Code: 3330202

7. SUGGESTED LIST OF PROPOSED STUDENT ACTIVITIES

Following is the list of proposed student activities like:

a. Seminar by students on various automobile transmission mechanisms like clutch, gear,

brakes actuating mechanisms etc.
b. Preparation of display boards or charts for steering mechanism, suspension system, different
types of brakes, wheels and tyres etc.
c. Assembly and disassembly of clutch actuating mechanism, gear box, differential, steering
mechanisms, brake actuating mechanism, steering, suspension systems, etc.
d. Individual or group-based projects to prepare working model of various mechanisms such
as brake operating mechanism, different clutch operating mechanism, steering mechanism,
model of differential etc.
e. Teacher guided self learning activities to prepare report as an assignment from industrial
survey/internet/library/or group discussion on any of the automobile transmission
mechanisms.
8. SUGGESTED INSTRUCTIONAL STRATEGIES (If Any)
a. Lecture cum discussion using demonstration of charts, cut section models,
animation and videos.
b. Visit of authorized workshop of two wheeler and four wheeler or transmission
component manufacturers.
c. Group discussion on any of the automobile transmission and mechanisms.

9. SUGGESTED LEARNING RESOURCES

A. List of Books

S.No. Author Title of Books Publication

1 R. B. Gupta Automobile Engineering SatyaPrakashan, New Delhi

2 Anil Chhikara Automobile Engineering SatyaPrakashan, New Delhi

vol-II
3 K. M. Gupta Automobile Engineering Umesh Publication

4 Jain K.K., Automobile Engineering Tata Mc-Graw Hill Publishing Co. Ltd.
Asthana R.B.
5 G. B. S. Narang Automobile Engineering Khanna Publishers

6 A. W. Judge Motor Manual London, 1925

7 W.H.Crouse & D.L. Transmission and power Tata Mc-Graw Hill Publishing Co. Ltd.
Anglin Train

8 Singh Kirpal Automobile Engineering: Standard Publishers Distributors

(Vol-II)
9 S. Srinivasan Automotive Mechanics Tata McGraw-Hill Education

GTU/ NITTTR Bhopal/12-13 Gujarat State

Automobile Transmission & Mechanism Course Code: 3330202

S.No. Author Title of Books Publication

10 N. K. Giri Automobile Technology Khanna Publishers

11 C.P. Nakra Basic Automobile DhanpatRai Publication Co. (P) Ltd.

Engineering

B. List of Major Equipment/ Instrument

a. Cut Sectioned working model of various types of clutches, gear boxes, fluid coupling/
torque convertor.
b. Cut sectioned working model of various brake systems, differential.
c. Display board of various steering gear mechanisms, power steering.
d. Display board of various types of suspension system and shock absorbers.
e. Charts for various types of chassis and frames, wheels and tyres.
C. List of Software/Learning Websites
a. http://www.youtube.com/watch?v=H7Iay0Ke_t4
b. http://www.youtube.com/watch?v=OQ9eI7mEmxw
c. 3.http://www.youtube.com/watch?v=FfjGohWy-OU
d. http://www.youtube.com/watch?v=IKywZ730JFs
e. http://www.youtube.com/watch?v=eKKfJAaVBjE
f. http://www.youtube.com/watch?v=aUlS25r3XY0
g. http://www.youtube.com/watch?v=VcFQZ8NiF4o
h. http://www.youtube.com/watch?v=17FG-GzVJyI
i. http://www.youtube.com/watch?v=1-ksUrWmBo4
j. http://www.ehow.com/video_2327738_overview-shocks-suspension-system.html
k. Howstuffworks.com
l. Wikipedia.com

GTU/ NITTTR Bhopal/12-13 Gujarat State

Automobile Transmission & Mechanism Course Code: 3330202

10. COURSE CURRICULUM DEVELOPMENT COMMITTEE

Faculty Members from Polytechnics
 Prof. D.A. Dave, H.O.D., Automobile Engineering Department, Sir Bhavsinhji
Polytechnic Institute, Bhavnagar.
 Prof. M.N. Vibhakar, Lecturer, Automobile Engineering Department, Dr. S&S
Gandhi Polytechnic, Surat.
 Prof. S.V. Trivedi, Lecturer, Automobile Engineering Department, Parul Institute of
Engineering and Technology, Vadodara.
 Prof. Sanjay Kumar Ghaiye, Head Automobile Engineering Department, Kalaniketan
Govt. Polytechnic, Jabalpur (MP).

Coordinator and Faculty Members from NITTTR Bhopal

 Dr. K.K. Jain, Professor, Department of Mechanical Engineering
 Dr. C.K. Chugh, Professor, Department of Electronic Media

GTU/ NITTTR Bhopal/12-13 Gujarat State