0% found this document useful (0 votes)

139 views

2 D Symbols Reference Data

2DSymbolsReferenceData

Uploaded by

Ramil

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

139 views

2 D Symbols Reference Data

2DSymbolsReferenceData

Uploaded by

Ramil

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 306

2D Symbols

Marine Mode Reference Data Guide

Version 2014 R1 (10.1)

June 2014

DSHIP-PE-200087G
Copyright
Copyright © 2006-2014 Intergraph® Corporation. All Rights Reserved. Intergraph is part of Hexagon.
Including software, file formats, and audiovisual displays; may be used pursuant to applicable software license agreement; contains
confidential and proprietary information of Intergraph and/or third parties which is protected by copyright law, trade secret law, and
international treaty, and may not be provided or otherwise made available without proper authorization from Intergraph Corporation.
Portions of this software are owned by Spatial Corp. © 1986-2014. All Rights Reserved.
Portions of the user interface copyright 2012-2014 Telerik AD.

U.S. Government Restricted Rights Legend

Use, duplication, or disclosure by the government is subject to restrictions as set forth below. For civilian agencies: This was developed
at private expense and is "restricted computer software" submitted with restricted rights in accordance with subparagraphs (a) through
(d) of the Commercial Computer Software - Restricted Rights clause at 52.227-19 of the Federal Acquisition Regulations ("FAR") and
its successors, and is unpublished and all rights are reserved under the copyright laws of the United States. For units of the Department
of Defense ("DoD"): This is "commercial computer software" as defined at DFARS 252.227-7014 and the rights of the Government are
as specified at DFARS 227.7202-3.
Unpublished - rights reserved under the copyright laws of the United States.
Intergraph Corporation
300 Intergraph Way
Huntsville, AL 35813

Documentation
Documentation shall mean, whether in electronic or printed form, User's Guides, Installation Guides, Reference Guides,
Administrator's Guides, Customization Guides, Programmer's Guides, Configuration Guides and Help Guides delivered with a
particular software product.

Other Documentation
Other Documentation shall mean, whether in electronic or printed form and delivered with software or on Intergraph Smart Support,
SharePoint, or box.net, any documentation related to work processes, workflows, and best practices that is provided by Intergraph as
guidance for using a software product.

Terms of Use
a. Use of a software product and Documentation is subject to the End User License Agreement ("EULA") delivered with the software
product unless the Licensee has a valid signed license for this software product with Intergraph Corporation. If the Licensee has a
valid signed license for this software product with Intergraph Corporation, the valid signed license shall take precedence and
govern the use of this software product and Documentation. Subject to the terms contained within the applicable license
agreement, Intergraph Corporation gives Licensee permission to print a reasonable number of copies of the Documentation as
defined in the applicable license agreement and delivered with the software product for Licensee's internal, non-commercial use.
The Documentation may not be printed for resale or redistribution.
b. For use of Documentation or Other Documentation where end user does not receive a EULA or does not have a valid license
agreement with Intergraph, Intergraph grants the Licensee a non-exclusive license to use the Documentation or Other
Documentation for Licensee’s internal non-commercial use. Intergraph Corporation gives Licensee permission to print a
reasonable number of copies of Other Documentation for Licensee’s internal, non-commercial. The Other Documentation may
not be printed for resale or redistribution. This license contained in this subsection b) may be terminated at any time and for any
reason by Intergraph Corporation by giving written notice to Licensee.

Disclaimer of Warranties
Except for any express warranties as may be stated in the EULA or separate license or separate terms and conditions, Intergraph
Corporation disclaims any and all express or implied warranties including, but not limited to the implied warranties of merchantability
and fitness for a particular purpose and nothing stated in, or implied by, this document or its contents shall be considered or deemed a
modification or amendment of such disclaimer. Intergraph believes the information in this publication is accurate as of its publication
date.
The information and the software discussed in this document are subject to change without notice and are subject to applicable
technical product descriptions. Intergraph Corporation is not responsible for any error that may appear in this document.
The software, Documentation and Other Documentation discussed in this document are furnished under a license and may be used or
copied only in accordance with the terms of this license. THE USER OF THE SOFTWARE IS EXPECTED TO MAKE THE FINAL
EVALUATION AS TO THE USEFULNESS OF THE SOFTWARE IN HIS OWN ENVIRONMENT.

2 2D Symbols Marine Mode Reference Data Guide

Intergraph is not responsible for the accuracy of delivered data including, but not limited to, catalog, reference and symbol data. Users
should verify for themselves that the data is accurate and suitable for their project work.

Limitation of Damages
IN NO EVENT WILL INTERGRAPH CORPORATION BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL INCIDENTAL,
SPECIAL, OR PUNITIVE DAMAGES, INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR PRODUCTION, LOSS OF REVENUE
OR PROFIT, LOSS OF DATA, OR CLAIMS OF THIRD PARTIES, EVEN IF INTERGRAPH CORPORATION HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES.
UNDER NO CIRCUMSTANCES SHALL INTERGRAPH CORPORATION’S LIABILITY EXCEED THE AMOUNT THAT INTERGRAPH
CORPORATION HAS BEEN PAID BY LICENSEE UNDER THIS AGREEMENT AT THE TIME THE CLAIM IS MADE. EXCEPT
WHERE PROHIBITED BY APPLICABLE LAW, NO CLAIM, REGARDLESS OF FORM, ARISING OUT OF OR IN CONNECTION
WITH THE SUBJECT MATTER OF THIS DOCUMENT MAY BE BROUGHT BY LICENSEE MORE THAN TWO (2) YEARS AFTER
THE EVENT GIVING RISE TO THE CAUSE OF ACTION HAS OCCURRED.
IF UNDER THE LAW RULED APPLICABLE ANY PART OF THIS SECTION IS INVALID, THEN INTERGRAPH LIMITS ITS LIABILITY
TO THE MAXIMUM EXTENT ALLOWED BY SAID LAW.

Export Controls
Intergraph Corporation’s software products and any third-party Software Products obtained from Intergraph Corporation, its
subsidiaries, or distributors (including any Documentation, Other Documentation or technical data related to these products) are
subject to the export control laws and regulations of the United States. Diversion contrary to U.S. law is prohibited. These Software
Products, and the direct product thereof, must not be exported or re-exported, directly or indirectly (including via remote access) under
the following circumstances:
a. To Cuba, Iran, North Korea, Sudan, or Syria, or any national of these countries.
b. To any person or entity listed on any U.S. government denial list, including but not limited to, the U.S. Department of Commerce
Denied Persons, Entities, and Unverified Lists, http://www.bis.doc.gov/complianceandenforcement/liststocheck.htm, the U.S.
Department of Treasury Specially Designated Nationals List, http://www.treas.gov/offices/enforcement/ofac/, and the U.S.
Department of State Debarred List, http://www.pmddtc.state.gov/compliance/debar.html.
c. To any entity when Licensee knows, or has reason to know, the end use of the Software Product is related to the design,
development, production, or use of missiles, chemical, biological, or nuclear weapons, or other un-safeguarded or sensitive
nuclear uses.
d. To any entity when Licensee knows, or has reason to know, that an illegal reshipment will take place.
Any questions regarding export or re-export of these Software Products should be addressed to Intergraph Corporation’s Export
Compliance Department, Huntsville, Alabama 35894, USA.

Trademarks
Intergraph, the Intergraph logo, PDS, SmartPlant, FrameWorks, I-Sketch, SmartMarine, IntelliShip, ISOGEN, SmartSketch,
SPOOLGEN, SupportManager, SupportModeler, Sapphire, and Intergraph Smart are trademarks or registered trademarks of
Intergraph Corporation or its subsidiaries in the United States and other countries. Microsoft and Windows are registered trademarks of
Microsoft Corporation. ACIS is a registered trademark of SPATIAL TECHNOLOGY, INC. Infragistics, Presentation Layer Framework,
ActiveTreeView Ctrl, ProtoViewCtl, ActiveThreed Ctrl, ActiveListBar Ctrl, ActiveSplitter, ActiveToolbars Ctrl, ActiveToolbars Plus Ctrl,
and ProtoView are trademarks of Infragistics, Inc. Incorporates portions of 2D DCM, 3D DCM, and HLM by Siemens Product Lifecycle
Management Software III (GB) Ltd. All rights reserved. Gigasoft is a registered trademark, and ProEssentials a trademark of Gigasoft,
Inc. VideoSoft and VXFlexGrid are either registered trademarks or trademarks of ComponentOne LLC 1991-2013, All rights reserved.
Oracle, JD Edwards, PeopleSoft, and Retek are registered trademarks of Oracle Corporation and/or its affiliates. Tribon is a trademark
of AVEVA Group plc. Alma and act/cut are trademarks of the Alma company. Other brands and product names are trademarks of their
respective owners.

2D Symbols Marine Mode Reference Data Guide 3

4 2D Symbols Marine Mode Reference Data Guide
Contents
Preface .......................................................................................................................................................... 9
Documentation Set ................................................................................................................................. 9
Documentation Comments ................................................................................................................... 12
Smart 3D and Oracle ............................................................................................................................ 12
What's New in 2D Symbols Reference Data ........................................................................................ 12

2D Symbols Reference Data ..................................................................................................................... 13

Bracket Symbols ....................................................................................................................................... 15

2S Brackets ........................................................................................................................................... 15
3S Trimmed Brackets ........................................................................................................................... 21
3S Lapped S1 Brackets ........................................................................................................................ 26
3S Lapped S1S2 Brackets .................................................................................................................... 31
3S Lapped S1S2S3 Brackets ............................................................................................................... 37
3S Lapped S1S3 Brackets .................................................................................................................... 38
3S Lapped S2 Brackets ........................................................................................................................ 40
3S Lapped S2S3 Brackets .................................................................................................................... 45
3S Lapped S3 Brackets ........................................................................................................................ 47
4S Brackets ........................................................................................................................................... 49
5S Brackets ........................................................................................................................................... 50
2S Flanged Brackets ............................................................................................................................. 51
3S Flanged Brackets ............................................................................................................................. 52

Flange Contours for Brackets .................................................................................................................. 55

Standard Bracket Flange Contour ........................................................................................................ 55

Chamfers .................................................................................................................................................... 57
Double Sided Chamfer .......................................................................................................................... 57
Single Sided Chamfers ......................................................................................................................... 57

Collars and Clips ....................................................................................................................................... 59

Non-Tight Clips ..................................................................................................................................... 59
Tight Collars .......................................................................................................................................... 63

Corner Features for Plates and Stiffeners .............................................................................................. 73

Corner Features for Members .................................................................................................................. 79

Member Cross Sections............................................................................................................................ 89

Cross Section Symbol 2L...................................................................................................................... 90
Cross Section Symbol BUBoxFM ......................................................................................................... 93
Cross Section Symbol BUC .................................................................................................................. 95
Cross Section Symbol BUCan .............................................................................................................. 97
Cross Section Symbol BUCone ............................................................................................................ 99

2D Symbols Marine Mode Reference Data Guide 5

Bevel3 (V-Type) .................................................................................................................................. 293

Bevel4 (X-Type) .................................................................................................................................. 293
Bevel5 (Y-Type) .................................................................................................................................. 293
Bevel6 (X-Type with Chamfer) ............................................................................................................ 293
Bevel7 (X-Type with Chamfer) ............................................................................................................ 294
Bevel8 (X-Type with Chamfer) ............................................................................................................ 294
Bevel9 (X-Type with Chamfer) ............................................................................................................ 294
Bevel10 ............................................................................................................................................... 294
BevelA ................................................................................................................................................. 295
BevelB ................................................................................................................................................. 295
BevelParam......................................................................................................................................... 296
FeatureTab1........................................................................................................................................ 296
Grind ................................................................................................................................................... 296
Knuckle ............................................................................................................................................... 297
Margin ................................................................................................................................................. 297
PartCenterLL ....................................................................................................................................... 297
PartDirC .............................................................................................................................................. 298
PartDirCL ............................................................................................................................................ 298
PartDirCR ............................................................................................................................................ 298
PartDirL ............................................................................................................................................... 299
PartDirLL ............................................................................................................................................. 299
PartDirLLFlangeRR ............................................................................................................................. 299
PartDirR .............................................................................................................................................. 300
PartDirRR ............................................................................................................................................ 300
PartDirRRFlangeLL ............................................................................................................................. 300
PMFeature .......................................................................................................................................... 301
Shrinkage ............................................................................................................................................ 301
SMPlateTab ........................................................................................................................................ 301
UnSpecBevel ...................................................................................................................................... 302
WeldTab1 ............................................................................................................................................ 302

Index ......................................................................................................................................................... 303

8 2D Symbols Marine Mode Reference Data Guide

Preface
This document is a reference data guide for the Intergraph SmartTM 3D 2D Symbols task. The
purpose of this document is to describe the reference data delivered with the software for this task.
Reference data includes both catalog data and specification data. Catalog data includes the parts
that you place in the model, such as piping components and equipment. Specification data
includes the rules that govern how those parts are placed and connected.

Documentation Set
Intergraph SmartTM 3DDocumentation is available as Adobe PDF files. The content is the same as
the online Help. To access these PDF documents, click Help > Printable Guides in the software.
The documentation set is divided into four categories:
 Administrative guides contain information about installing, configuring, customizing, and
troubleshooting.
 User's guides provide command reference and how-to information for working in each task.
 Reference data guides define the reference data workbooks. Not all tasks have reference
data.
 ISOGEN guides.

Administrative Guides
Intergraph SmartTM 3D Installation Guide - Provides instructions on installing and configuring the
software.
Project Management User's Guide - Provides instructions for setting up the databases, creating
permission groups, backing up and restoring project data, assigning access permissions to the
model, defining and managing locations for Global Workshare, and version upgrade.
Global Workshare Guide - Provides instructions for setting up the software and the databases to
work in a workshare environment.
Interference Checking Guide - Provides information on installing, configuring, and using the
interference detection service.
Integration Reference Guide - Provides information about installing, configuring, and using Smart
3D in an integrated environment.
Interpreting Human Piping Specifications - Provides information about how to interpret human
piping specifications so that you can create the corresponding piping specification in the software.
Design and Data Exchange with PDMS - Provides information about how to export model data
from Smart 3D to PDMS and from PDMS to Smart 3D. Specific guidelines relating to best
practices and known limitations of the export functionality are also included.
Export to Plant Design System (PDS) User's Guide - Provides information about how to export
model data from Smart 3D to PDS. Specific guidelines relating to best practices and known
limitations of the export functionality are also included.

2D Symbols Marine Mode Reference Data Guide 9

Preface

Point Cloud Reference - Provides information for referencing point cloud files provided by point
cloud vendors in Smart 3D.
Troubleshooting Reference Guide - Provides information on how to resolve errors that you might
encounter in the software by documenting troubleshooting tips, error messages, and To Do List
messages.
Plant Design System (PDS) Guide - Provides all information needed to use PDS with Smart 3D.
Topics include referencing active PDS projects in Smart 3D, exporting PDS data and importing
that data into Smart 3D, and converting PDS reference data to Smart 3D reference data.
Intergraph SmartTM 3D Programmer's Guide - Provides information about custom commands,
naming rules, and symbol programming. If you install the Programming Resources, this document
is delivered to the [Product Folder]\Programming\Help folder.

User's Guides
Catalog User's Guide - Provides information about viewing, editing, and creating reference data
and select lists (codelists).
Civil User's Guide - Provides information about routing trench runs in the model.
Common User's Guide - Provides information about defining workspaces, manipulating views,
and running reports.
Compartmentation User's Guide - Provides instruction for placing volume objects such as
compartments and zones in the model.
Electrical User's Guide - Provides information about routing electrical cable, cableway, cable tray,
and conduit.
Equipment and Furnishings User's Guide - Provides information about placing equipment.
Geometry Analysis and Repair User's Guide - Provides instructions for importing and exporting
model data, checking the data against a defined set of requirements, and repairing the data.
Grids User's Guide - Provides instructions for creating coordinate systems, elevation grid planes,
vertical grid planes, radial cylinders, radial planes, grid arcs, and grid lines.
Hangers and Supports User's Guide - Provides instructions on placing piping, duct, and cableway
supports in the model.
Hole Management User's Guide - Provides instructions for placing, reviewing, and approving
holes in a structure.
HVAC User's Guide - Provides instructions for routing HVAC duct.
Molded Forms User's Guide - Provides instructions for placing hull, bulkheads, major openings,
stiffeners, and other major structural components in the model.
Orthographic Drawings User's Guide - Provides information about creating and managing
orthographic drawings.
Piping Isometric Drawings User's Guide - Provides information about creating and managing
piping isometric drawings.
Piping User's Guide - Provides instructions for routing pipe and placing valves, taps, and pipe
joints.
Planning User's Guide - Provides instructions about defining the assembly hierarchy (production
bill of material) by creating blocks and assemblies and by specifying the assembly sequence.

10 2D Symbols Marine Mode Reference Data Guide

Preface

Reports User's Guide - Provides information about creating and managing spreadsheet reports.
Space Management User's Guide - Provides instructions for placing space objects such as areas,
zones, interference volumes, and drawing volumes in the model.
Structural Analysis User's Guide - Provides instructions for defining loads, load cases, load
combinations, and the importing and exporting of analytical data.
Structural Detailing User's Guide - Provides instructions for creating, detailing, and maintaining
the structural members of a model.
Structural Manufacturing User's Guide - Provides instructions for creating and maintaining
manufacturing objects such as templates, jigs, and margins.
Structure User's Guide - Provides instructions for placing structural members, such as beams,
columns, slabs, openings, stairs, ladders, equipment foundations, and handrails.
Systems and Specifications User's Guide - Provides instructions for creating systems and
selecting the available specifications for each system type.

Reference Data Guides

2D Symbols User's Guide - Provides command reference information and procedural instructions
for creating 2D symbols used to represent collars, clips, profiles, brackets, and other items.
2D Symbols Reference Data Guide - Provides information about the two-dimensional symbols
used in all tasks.
Civil Reference Data Guide - Provides information about trench straight features, turn features,
reference data.
Compartmentation Reference Data Guide - Provides information about compartmentation
reference data.
Drawings and Reports Reference Data Guide - Provides information about reports reference data.
Electrical Reference Data Guide - Provides information about electrical cable, cableway, cable
tray, and conduit reference data.
Electrical 3D Symbols Reference - Provides information about the cable tray and conduit 3D
symbols that are available.
Equipment and Furnishings Reference Data Guide - Provides information about equipment
reference data.
Equipment 3D Symbols Reference - Provides information about the equipment, equipment
component, design shapes, and design aides 3D symbols that are available.
Hangers and Supports Reference Data Guide - Provides information about hangers and supports
reference data.
Hangers and Supports 3D Symbols Reference - Provides information about the hanger and
support 3D symbols that are available.
Hangers and Supports SmartPart Symbols Reference - Provides information about the hanger
and support SmartPart symbols that are available.
Hole Management Reference Data Guide - Provides information about hole reference data.
HVAC Reference Data Guide - Provides information about HVAC reference data.

2D Symbols Marine Mode Reference Data Guide 11

Preface

HVAC 3D Symbols Reference - Provides information about the HVAC 3D symbols that are
available.
Reference Data Guide - Provides instructions about the Bulkload utility, codelists, and the
reference data common to several disciplines.
Piping Reference Data Guide - Provides information about piping reference data including piping
specifications, piping specification rules, piping parts, and piping symbols.
Piping 3D Symbols Reference - Provides information about the piping 3D symbols that are
available.
Space Management Reference Data Guide - Provides information about space management
reference data.
Structure Reference Data Guide - Provides information about structural reference data.
Structure 3D Symbols Reference - Provides information about the stair, ladder, footings, and
equipment foundation 3D symbols that are available.
Structural Reference Data Overview - Provides an overview of the marine mode structural
reference data library.

ISOGEN Guides
Symbol Keys Reference Guide - Provides information about the symbol keys for isometric
drawings. This guide is from Alias, the makers of ISOGEN.

Documentation Comments
We welcome comments or suggestions about this documentation. You can send us an email at:
[email protected].
Documentation updates for supported software versions are available from
https://smartsupport.intergraph.com (https://smartsupport.intergraph.com).

Smart 3D and Oracle

Throughout the software and documentation, there are references and options pertaining to
Oracle databases. Intergraph SmartTM 3D plant mode supports Oracle, but marine mode and
material handling mode do not. Please remember that when using marine mode or material
handling mode, always select the SQL option when given a choice between Oracle and SQL.

What's New in 2D Symbols Reference Data

The following changes have been made to the 2D symbols reference data.
Version 2014 R1 (10.1)
 Added information on Structural Manufacturing requirements for profile and member cross
sections. For more information, see Manufacturing Requirements for Profile Cross Sections
(on page 290) and Manufacturing Requirements for Member Cross Sections (on page 291).

12 2D Symbols Marine Mode Reference Data Guide

2D Symbols Reference Data

SECTION 1

2D Symbols Reference Data

The 2D Symbols utility is delivered with the software and is used to create symbols representing
profile cross-sections, brackets, slots, collars, end cuts, detailing features, and manufacturing
features in the Molded Forms and Structural Detailing tasks; member cross-sections in the
Structure task; and facilitate using these symbols in a modeling environment.
This document describes all of the 2D symbols that are delivered with the software. The symbol
library is delivered to the SharedContent share in the [Reference Data Product
Directory]\SharedContent folder
You can create your own custom symbols using the 2D Symbols utility. To learn how to create 2D
symbols, refer to the 2D Symbols User's Guide.
Two sets of 2D symbols are delivered: default and marine library. The default set
contains basic symbols suitable for prototyping. The marine library set provides a more complete
set of marine symbols.

2D Symbols Marine Mode Reference Data Guide 13

2D Symbols Reference Data

14 2D Symbols Marine Mode Reference Data Guide

SECTION 2

Bracket Symbols
Bracket symbols are delivered in two locations:
 [Reference Data Folder]\SharedContent\Marine Library\Brackets folder. Within the Brackets
folder, the folder hierarchy is further organized by the number of supports and by whether the
bracket is trimmed or lapped.
 [Reference Data Folder]\SharedContent\Brackets folder. Within the Brackets folder, the folder
hierarchy is further organized by the number of supports.

In This Section
2S Brackets.................................................................................... 15
3S Trimmed Brackets .................................................................... 21
3S Lapped S1 Brackets ................................................................. 26
3S Lapped S1S2 Brackets............................................................. 31
3S Lapped S1S2S3 Brackets ........................................................ 37
3S Lapped S1S3 Brackets............................................................. 38
3S Lapped S2 Brackets ................................................................. 40
3S Lapped S2S3 Brackets............................................................. 45
3S Lapped S3 Brackets ................................................................. 47
4S Brackets.................................................................................... 49
5S Brackets.................................................................................... 50
2S Flanged Brackets ..................................................................... 51
3S Flanged Brackets ..................................................................... 52

2S Brackets
2S brackets have two supports. Brackets can be trimmed or lapped to one or both supports.
The following 2S bracket symbols are delivered in the [Reference Data
Folder]\SharedContent\Marine Library\Brackets\2S folder.

2D Symbols Marine Mode Reference Data Guide 15

Bracket Symbols

Name Description Parameters

2SBracketLinear Linear free edge

Name Description Parameters

2SCL_2Lap Curved free edge

Both supports are
lapped

2SCL_2Lap_wScallop Curved free edge

Both supports are
lapped
Corner scallop

2SBracketCurvLin

The following 2S bracket symbols are delivered in the [Reference Data

Folder]\SharedContent\Brackets\2S folder.

2D Symbols Marine Mode Reference Data Guide 19

Bracket Symbols

Name Parameters

2SBracketCurved

2SBracketCurvLin

20 2D Symbols Marine Mode Reference Data Guide

Bracket Symbols

Name Parameters

2SBracketLinear

3S Trimmed Brackets
3S trimmed brackets have three supports. Brackets are trimmed to all three supports.
3S trimmed bracket symbols are delivered in the SharedContent share in the [Reference Data
Folder]\SharedContent\Marine Library\Brackets\3S\Trimmed folder.

Offset from Support 1

Name Description Parameters

3SLT Linear free edge

Offset

2D Symbols Marine Mode Reference Data Guide 21

Bracket Symbols

ToFlangeScallop radius at Support 3
Corner scallop

3S Lapped S1 Brackets
3S lapped S1brackets have three supports. Brackets are lapped to Support 1.
3S lapped S1 bracket symbols are delivered in the SharedContent share in the [Reference Data
Folder]\SharedContent\Marine Library\Brackets\3S\Lapped\Sup1 folder.

Offset from Support 1

Name Description Parameters

3SLLS1 Linear free edge

Offset

26 2D Symbols Marine Mode Reference Data Guide

Bracket Symbols

SetBack

2D Symbols Marine Mode Reference Data Guide 29

Bracket Symbols

Name Description Parameters

3SLLS1 Linear free edge

SetBackScallop
Corner scallop

3SCLS1 Curved free edge

SetBack

3SCLS1 Curved free edge

SetBackScallop
Corner scallop

30 2D Symbols Marine Mode Reference Data Guide

Bracket Symbols

3S Lapped S1S2 Brackets

3S lapped S1S2 brackets have three supports. Brackets are lapped to Support1 and Support2.
3S lapped S1S2 bracket symbols are delivered in the SharedContent share in the [Reference
Data Folder]\SharedContent\Marine Library\Brackets\3S\Lapped\Sup1Sup2 folder.

Offset from Support 1

Name Description Parameters

3SLLS1S2 Linear free edge

Offset

3SLLS1S2 Linear free edge

OffsetScallop
Corner scallop

3SCLS1S2 Curved free edge

Offset

2D Symbols Marine Mode Reference Data Guide 31

Bracket Symbols

Name Description Parameters

FlangeOutFillet with radius at
Support 3

3SLLS1S2 Linear free edge

FlangeOutFilletScallop with radius at
Support 3
Corner scallop

Offset from Flange of Support 3

Name Description Parameters

3SLLS1S2 Linear free edge

OffsetFromFlange

2D Symbols Marine Mode Reference Data Guide 33

Bracket Symbols

Bracket Symbols

3SCLS1S2S3 Curved free edge

OffsetScallop
Corner scallop

3S Lapped S1S3 Brackets

3S lapped S1S3 brackets have three supports. Brackets are lapped to Support1 and Support3.
3S lapped S1S3 bracket symbols are delivered in the SharedContent share in the [Reference
Data Folder]\SharedContent\Marine Library\Brackets\3S\Lapped\Sup1Sup3 folder.

OffsetScallop
Corner scallop

3SCLS2 Curved free edge

Offset

40 2D Symbols Marine Mode Reference Data Guide

Bracket Symbols

Name Description Parameters

3SCLS2 Curved free edge

OffsetScallop
Corner scallop

Offset from Support 1, with Radius on the Free Edge

Name Description Parameters

3SLLS2 Linear free edge

FlangeInFillet with radius at
Support 3, offset to
clear the flange

3SLLS1S2 Linear free edge

FlangeInFilletScallop with radius at
Support 3, offset to
clear the flange
Corner scallop

2D Symbols Marine Mode Reference Data Guide 41

Bracket Symbols

Name Description Parameters

3SLLS2 Linear free edge

FlangeOutFillet with radius at
Support 3

3SLLS1S2 Linear free edge

FlangeOutFilletScallop with radius at
Support 3
Corner scallop

Offset from Flange of Support 3

Name Description Parameters

3SLLS2 Linear free edge

OffsetFromFlange

3SLLS1S2 Linear free edge

OffsetFromFlangeScallop
Corner scallop

42 2D Symbols Marine Mode Reference Data Guide

Bracket Symbols

Name Description Parameters

3SCLS2 Curved free edge

OffsetFromFlange

3SCLS1S2 Curved free edge

OffsetFromFlangeScallop
Corner scallop

Set Back from Support 3

Name Description Parameters

3SLLS2 Linear free edge

SetBack

2D Symbols Marine Mode Reference Data Guide 43

Bracket Symbols

OffsetScallop
Corner scallop

3SCLS2S3 Curved free edge

Offset

46 2D Symbols Marine Mode Reference Data Guide

Bracket Symbols

Name Description Parameters

3SCLS2S3 Curved free edge

OffsetScallop
Corner scallop

3S Lapped S3 Brackets
3S lapped S3 brackets have three supports. Brackets are lapped to Support3.
3S lapped S3 bracket symbols are delivered in the SharedContent share in the [Reference Data
Folder]\SharedContent\Marine Library\Brackets\3S\Lapped\Sup3 folder.

Offset from Support 1

Name Description Parameters

3SLLS3 Linear free edge

Offset

3SLLS3 Linear free edge

OffsetScallop
Corner scallop

2D Symbols Marine Mode Reference Data Guide 47

Bracket Symbols

Name Description Parameters

3SCLS3 Curved free edge

Offset

3SCLS3 Curved free edge

OffsetScallop
Corner scallop

48 2D Symbols Marine Mode Reference Data Guide

Bracket Symbols

4S Brackets
4S brackets have four supports. Brackets can be trimmed or lapped to Support1 and Support2,
but are trimmed to Support3 and Support4.
The following 4S bracket symbols are delivered in the [Reference Data
Folder]\SharedContent\Marine Library\Brackets\4S folder.

Name Description Parameters

4SLT Linear free edge

Offset
Trimmed to
supports
Offset from
Support 3

4SCLT Linear free edge

OffsetFromFlangeScallop with radii at
Support3 and
Support 4
Trimmed to
supports
Offset from flange
of
Support 3
Corner scallops

The following 4S bracket symbol is delivered in the [Reference Data

Folder]\SharedContent\Brackets\4SNew folder.

2D Symbols Marine Mode Reference Data Guide 49

Bracket Symbols

Name Parameters

4SBracketPlates

5S Brackets
5S brackets have four supports. Brackets can be trimmed to all supports.
The following 5S bracket symbols are delivered in the [Reference Data
Folder]\SharedContent\Brackets\5SNew folder.

Name Parameters

5SBracketPlates

50 2D Symbols Marine Mode Reference Data Guide

Bracket Symbols

Name Parameters

OffsetFromFlange

2D Symbols Marine Mode Reference Data Guide 53

Bracket Symbols

54 2D Symbols Marine Mode Reference Data Guide

SECTION 3

Flange Contours for Brackets

Flange contour symbols are used with flanged bracket symbols. Flange contour symbols are
delivered in the [Reference Data Folder]\SharedContent\Marine Library\Flange Contours folder.

Standard Bracket Flange Contour

2D Symbols Marine Mode Reference Data Guide 55

Flange Contours for Brackets

56 2D Symbols Marine Mode Reference Data Guide

SECTION 4

Chamfers
The chamfer symbols are delivered with the software in the SharedContent share in the
[Reference Data Folder]\SharedContent\Web Cuts and [Reference Data
Folder]\SharedContent\Marine Library\Chamfer folders.

Double Sided Chamfer

Single Sided Chamfers

SingleSidedBase

2D Symbols Marine Mode Reference Data Guide 57

Chamfers

SingleSidedOffset

58 2D Symbols Marine Mode Reference Data Guide

SECTION 5

Collars and Clips

Collar and clip symbols are delivered in two locations:
 [Reference Data Folder]\SharedContent\Marine Library\Collars folder.
 [Reference Data Folder]\SharedContent\Collars folder.

In This Section
Non-Tight Clips ...............................................................................59
Tight Collars....................................................................................63

Non-Tight Clips
Clips are open on at least one side of the slot.
The following clip symbols are delivered in the [Reference Data Folder]\SharedContent\Marine
Library\Collars folder.

Name Cross- Selection Logic in Parameters

Sections the Rules
Supported

ClipAA_SM All Clip A

Non-tight
SlotA or Slot C
Profile height 
200mm (EA, UA, FB,
BUT, BUTL2)
Profile height 
180mm (B)

2D Symbols Marine Mode Reference Data Guide 59

Collars and Clips

Name Cross- Selection Logic in Parameters

Sections the Rules
Supported

ClipAAC_BT All Default selection for

(curved top) all cross-sections
ClipAAC_ST Clip C
(straight top)
Non-tight
SlotA or Slot C
Profile height 
100mm (EA, UA, FB,
BUT, BUTL2)
Profile height 
180mm (B)

ClipAAC_BT_Left EA Collar
Order=Secondary
UA
25 < SlotAngle < 65
BUT
(deg)
BUTL2
Available in ClipC
B
FB

ClipAAC_ST_S EA 0.1 < SlotAngle < 25

(deg)
UA
Available in ClipC
BUT
BUTL2

60 2D Symbols Marine Mode Reference Data Guide

Collars and Clips

Name Cross- Selection Logic in Parameters

Sections the Rules
Supported

ClipAAC_ST_Left Collar
Order=Secondary
SlotAngle < 0.1
(deg)
Available in ClipC

ClipAAC_ST_S_Left Collar
Order=Secondary
0.1 < SlotAngle < 25
(deg)
Available in ClipC

ClipAB_SM EA Available in ClipB

UA
B
BUT
FB
BUTL2

The following clip symbols are delivered in the [Reference Data Folder]\SharedContent\Collars
folder.

2D Symbols Marine Mode Reference Data Guide 61

Collars and Clips

Name Parameters

ClipAA
Clip BA

Clip AB
Clip BB

Clip AAC
Clip BAC

62 2D Symbols Marine Mode Reference Data Guide

Collars and Clips

Name Parameters

Clip ABC
Clip BBC

Tight Collars
Collars are welded around all sides of the slot.
The following collar symbols are delivered in the [Reference Data Folder]\SharedContent\Marine
Library\Collars folder.

Name Cross- Selection Logic in the Parameters

Sections Rules
Supported

CollarAIT_SM EA CollarNoSnipe
UA Tight
Slot I
CollarTIT_SM BUT
BUTL2

CollarACT_SM EA CollarOneSnipe
UA Tight
Slot C
CollarBCT_SM B

CollarFCT_SM FB

CollarTCT_SM BUT
BUTL2

2D Symbols Marine Mode Reference Data Guide 63

Collars and Clips

Name Cross- Selection Logic in the Parameters

Sections Rules
Supported

CollarACT_A EA CollarOneSnipe
UA Tight
Slot C
CollarBCT_A B (SlotXC_LT_PAT)

CollarFCT_A FB

CollarACT_A2 EA CollarOneSnipe
UA Tight
Slot C
CollarBCT_A2 B (SlotXC_LT_PAT2)

CollarFCT_A2 FB

CollarBCT_A3 B CollarOneType
Available when
Slot=SlotBC_L_LTT_STR

64 2D Symbols Marine Mode Reference Data Guide

Collars and Clips

Name Cross- Selection Logic in the Parameters

Sections Rules
Supported

CollarTCT_A BUT CollarOneSnipe

(right side)
BUTL2 Tight
CollarTCT_B
Slot C2
(left side)
(SlotXC2_T_PTT_STR)

Collar_Scallop BUT ScallopWithCollar

BUTL2

Collar_LongScallo BUT LongScallopWithCollar

p
BUTL2
EA
UA

2D Symbols Marine Mode Reference Data Guide 65

Collars and Clips

Name Cross- Selection Logic in the Parameters

Sections Rules
Supported

CollarTCT_A2 BUT CollarOneSnipe

(right side)
BUTL2 Tight
CollarTCT_B2
EA Slot C2
(left side)
(SlotXC2_T_PTT_STR2)
UA

ClipType=CollarOneType

CollarTCT_A3 Available when Slot =

SlotTC2_T_PAA_STR
and CollarOrder = Primary
BUT
ClipType=CollarOneType
Available when Slot =
CollarTCT_B3 SlotTC2_T_PAA_STR
and CollarOrder =
Secondary

CollarAAT_SM EA CollarTwoSnipes
UA Tight
Slot A
CollarBAT_SM B

CollarFAT_SM FB

CollarTAT_SM BUT
BUTL2

The following collar symbols are delivered in the [Reference Data Folder]\SharedContent\Collars
folder.

66 2D Symbols Marine Mode Reference Data Guide

Collars and Clips

Name Parameters

Collar AIT

Collar FIT

Collar TIT

2D Symbols Marine Mode Reference Data Guide 67

Collars and Clips

Name Parameters

Collar TsIT

Collar ACT

68 2D Symbols Marine Mode Reference Data Guide

Collars and Clips

Name Parameters

Collar BCT

Collar FCT

2D Symbols Marine Mode Reference Data Guide 69

Collars and Clips

Name Parameters

Collar AAT

Collar BAT

70 2D Symbols Marine Mode Reference Data Guide

Collars and Clips

Name Parameters

Collar FAT

Collar TAT

Collar TsAT

2D Symbols Marine Mode Reference Data Guide 71

Collars and Clips

Name Parameters

Collar LAT

72 2D Symbols Marine Mode Reference Data Guide

SECTION 6

Corner Features for Plates and Stiffeners

The following corner feature symbols are delivered in the [Reference Data Product
Folder]\SharedContent\Marine Library\Corner Features and [Reference Data Product
Folder]\SharedContent\Corner Features folders.

gaps and seams.
When a part crosses
a slot gap, rules
calculate values to
clear the slot gap.

Long Scallop Along Available in

Corner SmartGeneralCorner.
Use when the Corner
feature needs a cut
along the corner.

Long Scallop With Seam Available in

SeamScallop.
Auto selected when a
seam is near a Corner
feature location within
15mm from the
otherwise default
corner feature edge.

Offset Radius Placed as a child of

an end cut with a gap
 15mm.

76 2D Symbols Marine Mode Reference Data Guide

Corner Features for Plates and Stiffeners

Name Description Parameters

Offset Radius Obtuse Placed as a child of

an end cut with a gap
> 15mm.

Offset Radius with Placed as a child of

Straight Part an end cut with a gap
> 15mm.

Offset Radius Obtuse Placed as a child of

with Straight Part an end cut with a gap
 15mm.

2D Symbols Marine Mode Reference Data Guide 77

Corner Features for Plates and Stiffeners

Name Description Parameters

Scallop With Collar Placed as a child of

Assembly
Connection.

Long Scallop With Seam This smart item is

With Collar available in the
drop-down of a corner
feature selection to
support the corner
feature with the seam
functionality. This
creates a corner
feature with a collar.

Long Scallop With Collar This smart item is

available in
drop-down of a corner
feature selection and
it creates a long
scallop corner feature
with a collar.

78 2D Symbols Marine Mode Reference Data Guide

SECTION 7

2D Symbols Marine Mode Reference Data Guide 89

Member Cross Sections

In This Section
Cross Section Symbol 2L .............................................................. 90
Cross Section Symbol BUBoxFM .................................................. 93
Cross Section Symbol BUC ........................................................... 95
Cross Section Symbol BUCan ....................................................... 97
Cross Section Symbol BUCone ..................................................... 99
Cross Section Symbol BUEndCan ................................................ 100
Cross Section Symbol BUFlat ....................................................... 102
Cross Section Symbol BUI ............................................................ 103
Cross Section Symbol BUIHaunch ................................................ 105
Cross Section Symbol BUITaperWeb ........................................... 107
Cross Section Symbol BUIUE ....................................................... 109
Cross Section Symbol BUL ........................................................... 111
Cross Section Symbol BUT ........................................................... 113
Cross Section Symbol BUTube ..................................................... 114
Cross Section Symbol C (MC) ....................................................... 116
Cross Section Symbol CS ............................................................. 118
Cross Section Symbol HSSC (Pipe) .............................................. 119
Cross Section Symbol HSSR ........................................................ 120
Cross Section Symbol HW ............................................................ 121
Cross Section Symbol HWWF ....................................................... 123
Cross Section Symbol L ................................................................ 124
Cross Section Symbol Rect ........................................................... 126
Cross Section Symbol RectC ........................................................ 128
Cross Section Symbol RectCWF ................................................... 129
Cross Section Symbol RectWF ..................................................... 131
Cross Section Symbol RS ............................................................. 132
Cross Section Symbol S ................................................................ 133
Cross Section Symbol ST .............................................................. 135
Cross Section Symbol T (MT)........................................................ 136
Cross Section Symbol W (M)......................................................... 138
Cross Section Symbol Wedge ....................................................... 140
Cross Section Symbol WedgeWF ................................................. 141

Cross Section Symbol 2L

The 2L cross section symbol defines double-angle sections and uses the following properties.

90 2D Symbols Marine Mode Reference Data Guide

Member Cross Sections

Group Id - Type the material group identification for the section.

Unit Weight - Type the weight of the section. The unit weight is defined in mass per length, pound
per foot (lb/ft).
Area - Type the cross-sectional area for the section. The area is defined in square inches or
square millimeters.
Depth - Type the depth for the section (longer legs). The depth is defined in inches or millimeters.
d - Type the other depth for the section (shorter legs). The depth is defined in inches or
millimeters.
bf - Type the width of a single angle. The width is defined in inches or millimeters.
Width - Type the width of the entire section. The width is defined in inches or millimeters.
Perimeter - Type the outside perimeter of the section.
tf - Type the flange thickness for the section. The thickness is defined in inches or millimeters.
tw - Type the web thickness for the section. The thickness is defined in inches or millimeters.
kdesign - Type the distance from outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail - Type the distance from outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
bb - Enter the back-to-back spacing on the section.
CentroidY - Type the centroid location along the y-axis. The location is defined in inches or
millimeters.
Ixx - Type the moment of inertia for the section's local x-axis.
Zxx - Type the plastic section modulus for the section's local x-axis.
Sxx - Type the section modulus for the section's local x-axis.
Rxx - Type the radius of gyration for the section's local x-axis.
Ryy - Type the radius of gyration for the section's local y-axis.
ro - Type the polar radius of gyration about the shear center.
H - Type the flexural constant.

2D Symbols Marine Mode Reference Data Guide 91

Member Cross Sections

The BUCone symbol uses the following properties.

Section Name - Type the section name. The section name must be unique within the section
standard.
Short Name - Type the short name for the section.
EDI Name - Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight - Type the weight of the section. The unit weight is defined in mass per length pound
per foot (lbm/ft).
Area - Type the cross-section area for the section.
Depth - Type the depth for the section. The depth is defined in meters
Width - Type the width for the section. The width is defined in meters.
Perimeter - The outside perimeter distance for the section.
Cone Thickness - Type the plate thickness of the cone plate.
Diameter Start - Type the cone diameter at the start.
Diameter End - Type the cone diameter at the end.
Length Start Cone - Type the start cone length. You can also enter any negative number to
indicate this length should be 1/3 of the total length.
Length End Cone - Type the end cone length. You can also enter any negative number to
indicate this length should be 1/3 of the total length.
CentroidX - Type the vertical distance from designated member edge to the centroidal axis.
CentroidY - Type the vertical distance from designated member edge to the centroidal axis.
Ixx - Type the moment of inertia for the section's local x-axis.
Zxx - Type the plastic section modulus for the section's local x-axis.
Sxx - Type the section modulus for the section's local x-axis.
Rxx - Type the radius of gyration for the section's local x-axis.
Iyy - Type the moment of inertia for the section's local y-axis.

2D Symbols Marine Mode Reference Data Guide 99

Member Cross Sections

Zyy - Type the plastic section modulus for the section's local y-axis.
Syy - Type the section modulus for the section's local y-axis.
Ryy - Type the radius of gyration for the section's local y-axis.
J - Type the torsional moment of inertia for the section.
Cw - Type the warping constant for the section.
ro - Type the polar radius of gyration about the shear center.
H - Type the flexural constant for the section.
IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
True.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, the default value is True.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, the default value is True.

Cross Section Symbol BUEndCan

The BUEndCan symbol uses the following properties.

Section Name - Type the section name. The section name must be unique within the section
standard.
Short Name - Type the short name for the section.

100 2D Symbols Marine Mode Reference Data Guide

Member Cross Sections

EDI Name - Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight - Type the weight of the section. The unit weight is defined in mass per length pound
per foot (lbm/ft).
Area - Type the cross-section area for the section.
Depth - Type the depth for the section. The depth is defined in meters
Width - Type the width for the section. The width is defined in meters.
Perimeter - The outside perimeter distance for the section.
Tube Thickness - Type the plate thickness of the main tube plate.
Tube Diameter - Type the diameter of the main tube.
Diameter Cone - Type the cone diameter.
Cone Length - Type the start cone length. You can also enter any negative number to indicate
this length should be 1/3 of the total length.
CentroidX - Type the vertical distance from designated member edge to the centroidal axis.
CentroidY - Type the vertical distance from designated member edge to the centroidal axis.
Ixx - Type the moment of inertia for the section's local x-axis.
Zxx - Type the plastic section modulus for the section's local x-axis.
Sxx - Type the section modulus for the section's local x-axis.
Rxx - Type the radius of gyration for the section's local x-axis.
Iyy - Type the moment of inertia for the section's local y-axis.
Zyy - Type the plastic section modulus for the section's local y-axis.
Syy - Type the section modulus for the section's local y-axis.
Ryy - Type the radius of gyration for the section's local y-axis.
J - Type the torsional moment of inertia for the section.
Cw - Type the warping constant for the section.
ro - Type the polar radius of gyration about the shear center.
H - Type the flexural constant for the section.
IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
True.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, the default value is True.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, the default value is True.

2D Symbols Marine Mode Reference Data Guide 101

Member Cross Sections

Cross Section Symbol BUFlat

The BUFlat symbol uses the following properties.

Section Name - Type the section name. The section name must be unique within the section
standard.
Short Name - Type the short name for the section.
EDI Name - Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight - Type the weight of the section. The unit weight is defined in mass per length pound
per foot (lbm/ft).
Area - Type the cross-section area for the section.
Depth - Type the depth for the section. The depth is defined in meters
Width - Type the width for the section. The width is defined in meters.
Perimeter - The outside perimeter distance for the section.
Web Thickness - Type the thickness of the top flange.
CentroidX - Type the vertical distance from designated member edge to the centroidal axis.
CentroidY - Type the vertical distance from designated member edge to the centroidal axis.
Ixx - Type the moment of inertia for the section's local x-axis.
Zxx - Type the plastic section modulus for the section's local x-axis.
Sxx - Type the section modulus for the section's local x-axis.
Rxx - Type the radius of gyration for the section's local x-axis.
Iyy - Type the moment of inertia for the section's local y-axis.
Zyy - Type the plastic section modulus for the section's local y-axis.
Syy - Type the section modulus for the section's local y-axis.
Ryy - Type the radius of gyration for the section's local y-axis.
J - Type the torsional moment of inertia for the section.

102 2D Symbols Marine Mode Reference Data Guide

Member Cross Sections

Cw - Type the warping constant for the section.

ro - Type the polar radius of gyration about the shear center.
H - Type the flexural constant for the section.
IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, the default value is True.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, the default value is True.

Cross Section Symbol BUI

The BUI symbol uses the following properties.

2D Symbols Marine Mode Reference Data Guide 103

Member Cross Sections

Top Flange Thickness - Type the plate thickness of the top flange.
Web Thickness - Type the thickness of the top flange.
CentroidX - Type the vertical distance from designated member edge to the centroidal axis.
CentroidY - Type the vertical distance from designated member edge to the centroidal axis.
Ixx - Type the moment of inertia for the section's local x-axis.
Zxx - Type the plastic section modulus for the section's local x-axis.
Sxx - Type the section modulus for the section's local x-axis.
Rxx - Type the radius of gyration for the section's local x-axis.
Iyy - Type the moment of inertia for the section's local y-axis.
Zyy - Type the plastic section modulus for the section's local y-axis.
Syy - Type the section modulus for the section's local y-axis.
Ryy - Type the radius of gyration for the section's local y-axis.
J - Type the torsional moment of inertia for the section.
Cw - Type the warping constant for the section.
ro - Type the polar radius of gyration about the shear center.
H - Type the flexural constant for the section.
gf - Type the bolt gage for the flange.
gw - Type the bolt gage for the web.

IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, the default value is True.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, the default value is True.

104 2D Symbols Marine Mode Reference Data Guide

Member Cross Sections

Cross Section Symbol BUIHaunch

The BUIHaunch symbol uses the following properties.

Section Name - Type the section name. The section name must be unique within the section
standard.
Short Name - Type the short name for the section.
EDI Name - Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight - Type the weight of the section. The unit weight is defined in mass per length pound
per foot (lbm/ft).
Area - Type the cross-section area for the section.
Depth - Type the depth for the section. The depth is defined in meters
Width - Type the width for the section. The width is defined in meters.
Perimeter - The outside perimeter distance for the section.
Top Flange Width - Type the width of the top flange.
Top Flange Thickness - Type the plate thickness of the top flange.
Bottom Flange Width - Type the width of the top flange.
Bottom Flange Thickness - Type the plate thickness of the top flange.
Length Start - Type the distance from the start of the member to where the haunch transition
should start. You can enter any negative number to specify the distance be 1/3 of the member
length.
Depth Start - Type the web depth at the start of the member.
Depth End - Type the web depth at the end of the member.
Depth Haunch - Type the web depth at the haunch.
Length End - Type the distance from the end of the member to where the haunch transition
should end. You can enter any negative number to specify the distance be 1/3 of the member
length.
Transition Gradient Start - Type the slope of the start transition.
Transition Gradient End - Type the slope of the end transition.

2D Symbols Marine Mode Reference Data Guide 109

Member Cross Sections

IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, whether or not the cross-section is symmetrical about the x-axis depends on
dimensional values.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, the default value is True.
Symmetries about the x- and y-axes are defined by design properties only. The Flange
Width Extension (top and bottom) property is not a design property; therefore, the symmetry
calculation is not affected by this property. This non-affect can cause discrepancies between the
symmetry of the cross-section graphic and the IsSymmetricAlongX and IsSymmetricAlongY
properties when non-zero width extensions are defined.

110 2D Symbols Marine Mode Reference Data Guide

Member Cross Sections

Cross Section Symbol BUL

The BUL symbol uses the following properties.

Section Name - Type the section name. The section name must be unique within the section
standard.
Short Name - Type the short name for the section.
EDI Name - Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight - Type the weight of the section. The unit weight is defined in mass per length pound
per foot (lbm/ft).
Area - Type the cross-section area for the section.
Depth - Type the depth for the section. The depth is defined in meters
Width - Type the width for the section. The width is defined in meters.
Perimeter - The outside perimeter distance for the section.
Bottom Flange Width - Type the width of the top flange.
Bottom Flange Thickness - Type the plate thickness of the top flange.
Web Thickness - Type the thickness of the top flange.
Depth Start - Type the web depth at the start of the member.
Depth End - Type the web depth at the end of the member.
CentroidX - Type the vertical distance from designated member edge to the centroidal axis.
CentroidY - Type the vertical distance from designated member edge to the centroidal axis.
Ixx - Type the moment of inertia for the section's local x-axis.

2D Symbols Marine Mode Reference Data Guide 111

Member Cross Sections

Zxx - Type the plastic section modulus for the section's local x-axis.
Sxx - Type the section modulus for the section's local x-axis.
Rxx - Type the radius of gyration for the section's local x-axis.
Iyy - Type the moment of inertia for the section's local y-axis.
Zyy - Type the plastic section modulus for the section's local y-axis.
Syy - Type the section modulus for the section's local y-axis.
Ryy - Type the radius of gyration for the section's local y-axis.
J - Type the torsional moment of inertia for the section.
Cw - Type the warping constant for the section.
ro - Type the polar radius of gyration about the shear center.
H - Type the flexural constant for the section.
lsg - Specify the bolt gage for the long side when there is one bolt row.
lsg1 - Specify the gage distance to the first bolt row on the long side when there are two bolt rows.
lsg2 - Specify the gage distance from the first bolt row to the second bolt row on the long side
when there are two bolt rows.
ssg - Specify the bolt gage for the short side when there is one bolt row.
ssg1 - Specify the gage distance to the first bolt row on the short side when there are two bolt
rows.
ssg2 - Specify the gage distance from the first bolt row to the second bolt row on the short side
when there are two bolt rows.

IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, the default value is False.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, whether or not the cross-section is symmetrical about the y-axis depends on
dimensional values.

112 2D Symbols Marine Mode Reference Data Guide

Member Cross Sections

Cross Section Symbol BUT

The BUT symbol uses the following properties.

Section Name - Type the section name. The section name must be unique within the section
standard.
Short Name - Type the short name for the section.
EDI Name - Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight - Type the weight of the section. The unit weight is defined in mass per length pound
per foot (lbm/ft).
Area - Type the cross-section area for the section.
Depth - Type the depth for the section. The depth is defined in meters
Width - Type the width for the section. The width is defined in meters.
Perimeter - The outside perimeter distance for the section.
Top Flange Width - Type the width of the top flange.
Top Flange Thickness - Type the plate thickness of the top flange.
Web Thickness - Type the thickness of the top flange.
Depth Start - Type the web depth at the start of the member.
Depth End - Type the web depth at the end of the member.
CentroidX - Type the vertical distance from designated member edge to the centroidal axis.
CentroidY - Type the vertical distance from designated member edge to the centroidal axis.
Ixx - Type the moment of inertia for the section's local x-axis.
Zxx - Type the plastic section modulus for the section's local x-axis.
Sxx - Type the section modulus for the section's local x-axis.

2D Symbols Marine Mode Reference Data Guide 113

Member Cross Sections

Rxx - Type the radius of gyration for the section's local x-axis.
Iyy - Type the moment of inertia for the section's local y-axis.
Zyy - Type the plastic section modulus for the section's local y-axis.
Syy - Type the section modulus for the section's local y-axis.
Ryy - Type the radius of gyration for the section's local y-axis.
J - Type the torsional moment of inertia for the section.
Cw - Type the warping constant for the section.
ro - Type the polar radius of gyration about the shear center.
H - Type the flexural constant for the section.
gf - Type the bolt gage for the flange.
gw - Type the bolt gage for the web.

IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, the default value is False.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, the default value is True.

Cross Section Symbol BUTube

The BUTube symbol uses the following properties.

Section Name - Type the section name. The section name must be unique within the section
standard.
Short Name - Type the short name for the section.

114 2D Symbols Marine Mode Reference Data Guide

Member Cross Sections

EDI Name - Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight - Type the weight of the section. The unit weight is defined in mass per length pound
per foot (lbm/ft).
Area - Type the cross-section area for the section.
Depth - Type the depth for the section. The depth is defined in meters
Width - Type the width for the section. The width is defined in meters.
Perimeter - The outside perimeter distance for the section.
Tube Thickness - Type the plate thickness of the tube plate.
Tube Diameter - Type the diameter of the tube.
CentroidX - Type the vertical distance from designated member edge to the centroidal axis.
CentroidY - Type the vertical distance from designated member edge to the centroidal axis.
Ixx - Type the moment of inertia for the section's local x-axis.
Zxx - Type the plastic section modulus for the section's local x-axis.
Sxx - Type the section modulus for the section's local x-axis.
Rxx - Type the radius of gyration for the section's local x-axis.
Iyy - Type the moment of inertia for the section's local y-axis.
Zyy - Type the plastic section modulus for the section's local y-axis.
Syy - Type the section modulus for the section's local y-axis.
Ryy - Type the radius of gyration for the section's local y-axis.
J - Type the torsional moment of inertia for the section.
Cw - Type the warping constant for the section.
ro - Type the polar radius of gyration about the shear center.
H - Type the flexural constant for the section.
IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
True.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, the default value is True.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, the default value is True.

2D Symbols Marine Mode Reference Data Guide 115

Member Cross Sections

Cross Section Symbol C (MC)

The C cross-section symbol defines channel sections and uses the following properties. The C
symbol is also used for MC cross-sections.

Section Name - Type the section name. This name appears when you label members. The
section name must be unique within the section standard.
Short Name - Type the short name for the section.
EDI Name - Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id - Type the material group identification for the section.
Unit Weight - Type the weight of the section. The unit weight is defined in mass per length pound
per foot (lbm/ft).
Area - Type the cross-sectional area for the section. The area is defined in square inches or
square millimeters.
Depth - Type the depth for the section. The depth is defined in inches or millimeters.
Width - Type the flange width for the section. The width is defined in inches or millimeters.
Perimeter - The outside perimeter distance for the section.
d - Type the depth for the section. The depth is defined in inches or millimeters.
bf - Type the flange width for the section. The width is defined in inches or millimeters.
tw - Type the web thickness for the section. The thickness is defined in inches or millimeters.
tf - Type the flange thickness for the section. The thickness is defined in inches or millimeters.
kdesign - Type the distance from the outer face of the flange to the web toe of the fillet of the
rolled shape or the equivalent distance on the welded section.
kdetail - Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX - Type the centroid location along the x-axis. The location is defined in inches or
millimeters.

116 2D Symbols Marine Mode Reference Data Guide

Member Cross Sections

eo_x - Type the shear center location along the x-axis. The location is defined in inches or
millimeters.
xp - Type the horizontal distance from the designated edge of member to its plastic neutral axis
(PNA). The distance is defined in inches or millimeters.
Ixx - Type the moment of inertia for the section's local x-axis.
Zxx - Type the plastic section modulus for the section's local x-axis.
Sxx - Type the section modulus for the section's local x-axis.
Rxx - Type the radius of gyration for the section's local x-axis.
Iyy - Type the moment of inertia for the section's local y-axis.
Zyy - Type the plastic section modulus for the section's local y-axis.
Syy - Type the section modulus for the section's local y-axis.
Ryy - Type the radius of gyration for the section's local y-axis.
J - Type the torsional moment of inertia for the section.
Cw - Type the warping constant for the section.
ro - Type the polar radius of gyration about the shear center.
H - Type the flexural constant in LRFD Specification Equation E3-1.
gf - Type the bolt gage for the flange.
gw - Type the bolt gage for the web.

IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, the default value is True.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, the default value is False.

2D Symbols Marine Mode Reference Data Guide 117

Member Cross Sections

Cross Section Symbol CS

The CS cross section symbol defines solid round sections and uses the following properties.

118 2D Symbols Marine Mode Reference Data Guide

Member Cross Sections

Cross Section Symbol HSSC (Pipe)

The HSSC cross section symbol defines circular, hollow structural sections and uses the following
properties. The HSSC symbol is also used for Pipe cross-sections.

Member Cross Sections

CentroidX - Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY - Type the vertical distance from the designated member edge to the centroidal axis.
Ixx - Type the moment of inertia for the section's local x-axis.
Zxx - Type the plastic section modulus for the section's local x-axis.
Sxx - Type the section modulus for the section's local x-axis.
Rxx - Type the radius of gyration for the section's local x-axis.
Iyy - Type the moment of inertia for the section's local y-axis.
Zyy - Type the plastic section modulus for the section's local y-axis.
Syy - Type the section modulus for the section's local y-axis.
Ryy - Type the radius of gyration for the section's local y-axis.
J - Type the torsional moment of inertia for the section.
Cw - Type the warping constant for the section.
ro - Type the polar radius of gyration about the shear center.
H - Type the flexural constant for the section.

Cross Section Symbol L

The L cross section symbol uses the following properties.

124 2D Symbols Marine Mode Reference Data Guide

Member Cross Sections

d - Type the overall depth (longer leg) for the section. The depth is defined in inches or millimeters.
bf - Type the overall width (shorter leg) for the section. The width is defined in inches or
millimeters.
tf - Type the flange thickness for the section. The thickness is defined in inches or millimeters.
tw - Type the web thickness for the section. The thickness is defined in inches or millimeters.
kdesign - Type the distance from the outer face of the flange to the web toe of the fillet of the
rolled shape or the equivalent distance on the welded section.
kdetail - Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX - Type the location of the centroid along the local x-axis. The location is defined in
inches or millimeters.
CentroidY - Type the location of the centroid along the local y-axis. The location is defined in
inches or millimeters.
xp - Type the distance from the designated edge of angle to its plastic neutral axis (PNA) along the
local x-axis.
yp - Type the distance from the designated edge of angle to its plastic neutral axis (PNA) along the
local y-axis.
Ixx - Type the moment of inertia for the section's local x-axis.
Zxx - Type the plastic section modulus for the section's local x-axis.
Sxx - Type the section modulus for the section's local x-axis.
Rxx - Type the radius of gyration for the section's local x-axis.
Iyy - Type the moment of inertia for the section's local y-axis.
Zyy - Type the plastic section modulus for the section's local y-axis.
Syy - Type the section modulus for the section's local y-axis.
Ryy - Type the radius of gyration for the section's local y-axis.
Rxy - Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.
J - Type the torsional moment of inertia for the section.
Cw - Type the warping constant for the section.
ro - Type the polar radius of gyration about the shear center.
H - Type the flexural constant for the section.
lsg - Specify the bolt gage for the long side when there is one bolt row.
lsg1 - Specify the gage distance to the first bolt row on the long side when there are two bolt rows.
lsg2 - Specify the gage distance from the first bolt row to the second bolt row on the long side
when there are two bolt rows.
ssg - Specify the bolt gage for the short side when there is one bolt row.
ssg1 - Specify the gage distance to the first bolt row on the short side when there are two bolt
rows.

2D Symbols Marine Mode Reference Data Guide 125

Member Cross Sections

Setback - Define the setback. This value is defined in meters.
Flange Right Width - Define the flange width on the right side. This valve is defined in meters.
Flange Left Width - Define the flange width on the left side. This valve is defined in meters.
Unit Weight - Type the weight of the section. The unit weight is defined in mass per length pound
per foot (lbm/ft).
Area - Type the cross-section area for the section.
Depth - Type the depth for the section. The depth is defined in meters
Width - Type the width for the section. The width is defined in meters.
Perimeter - The outside perimeter distance for the section.
d - Type the depth for the section.
bf - Type the width for the section.
tw - Type the web thickness for the section. The thickness is defined in meters.
tf - Type the flange thickness for the section. The thickness is defined in meters.
kdesign - Type the distance from the outer face of the flange to the web toe of the fillet of the
rolled shape or the equivalent distance on the welded section.
kdetail - Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX - Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY - Type the vertical distance from the designated member edge to the centroidal axis.
Ixx - Type the moment of inertia for the section's local x-axis.
Zxx - Type the plastic section modulus for the section's local x-axis.
Sxx - Type the section modulus for the section's local x-axis.
Rxx - Type the radius of gyration for the section's local x-axis.
Iyy - Type the moment of inertia for the section's local y-axis.
Zyy - Type the plastic section modulus for the section's local y-axis.
Syy - Type the section modulus for the section's local y-axis.
Ryy - Type the radius of gyration for the section's local y-axis.
J - Type the torsional moment of inertia for the section.
Cw - Type the warping constant for the section.
ro - Type the polar radius of gyration about the shear center.
H - Type the flexural constant for the section.

130 2D Symbols Marine Mode Reference Data Guide

Member Cross Sections

Cross Section Symbol RectWF

The RectWF symbol uses the following properties.

Section Name - Type the section name. The section name must be unique within the section
standard.
Short Name - Type the short name for the section.
EDI Name - Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id - Type the material group identification for the section.
Flange Right Width - Define the flange width on the right side. This valve is defined in meters.
Flange Left Width - Define the flange width on the left side. This valve is defined in meters.
Unit Weight - Type the weight of the section. The unit weight is defined in mass per length pound
per foot (lbm/ft).
Area - Type the cross-section area for the section.
Depth - Type the depth for the section. The depth is defined in meters
Width - Type the width for the section. The width is defined in meters.
Perimeter - The outside perimeter distance for the section.
d - Type the depth for the section.
bf - Type the width for the section.
tw - Type the web thickness for the section. The thickness is defined in meters.
tf - Type the flange thickness for the section. The thickness is defined in meters.
kdesign - Type the distance from the outer face of the flange to the web toe of the fillet of the
rolled shape or the equivalent distance on the welded section.
kdetail - Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidY - Type the vertical distance from designated member edge to the centroidal axis.

2D Symbols Marine Mode Reference Data Guide 131

Member Cross Sections

Ixx - Type the moment of inertia for the section's local x-axis.
Zxx - Type the plastic section modulus for the section's local x-axis.
Sxx - Type the section modulus for the section's local x-axis.
Rxx - Type the radius of gyration for the section's local x-axis.
Iyy - Type the moment of inertia for the section's local y-axis.
Zyy - Type the plastic section modulus for the section's local y-axis.
Syy - Type the section modulus for the section's local y-axis.
Ryy - Type the radius of gyration for the section's local y-axis.
J - Type the torsional moment of inertia for the section.
Cw - Type the warping constant for the section.
ro - Type the polar radius of gyration about the shear center.
H - Type the flexural constant for the section.

Cross Section Symbol RS

The RS cross section symbol defines rectangular solids and uses the following properties.

132 2D Symbols Marine Mode Reference Data Guide

Member Cross Sections

Cross Section Symbol S

The S cross section symbol uses the following properties.

2D Symbols Marine Mode Reference Data Guide 133

Member Cross Sections

Member Cross Sections

gw - Type the bolt gage for the web.

IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, the default value is False.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, the default value is True.

Cross Section Symbol W (M)

The W symbol uses the following properties. The W symbol is also used for M cross-sections.

138 2D Symbols Marine Mode Reference Data Guide

Member Cross Sections

kdesign - Type the distance from the outer face of the flange to the web toe of the fillet of the
rolled shape or the equivalent distance on the welded section.
kdetail - Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
Fy3p - Type the maximum yield stress for the section.
Ixx - Type the moment of inertia for the section's local x-axis.
Zxx - Type the plastic section modulus for the section's local x-axis.
Sxx - Type the section modulus for the section's local x-axis.
Rxx - Type the radius of gyration for the section's local x-axis.
Iyy - Type the moment of inertia for the section's local y-axis.
Zyy - Type the plastic section modulus for the section's local y-axis.
Syy - Type the section modulus for the section's local y-axis.
Ryy - Type the radius of gyration for the section's local y-axis.
J - Type the torsional moment of inertia for the section.
Cw - Type the warping constant for the section.
Wno - Type the normalized warping function. The function is defined in square inches or square
millimeters.
Sw - Type the warping statical moment. The moment is defined in in4 or mm4.
Qf - Type the first moment of area for the flange.
Qw - Type the first moment of area for the web.
gf - Type the bolt gage for the flange.
gw - Type the bolt gage for the web.

IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, the default value is True.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, the default value is True.

2D Symbols Marine Mode Reference Data Guide 139

Member Cross Sections

Cross Section Symbol Wedge

The Wedge symbol uses the following properties.

Section Name - Type the section name. The section name must be unique within the section
standard.
Short Name - Type the short name for the section.
EDI Name - Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id - Type the material group identification for the section.
Angle Right - Define the angle on the right side of the web.
Angle Left - Define the angle on the left side of the web.
Unit Weight - Type the weight of the section. The unit weight is defined in mass per length pound
per foot (lbm/ft).
Area - Type the cross-section area for the section.
Depth - Type the depth for the section. The depth is defined in meters
Width - Type the width for the section. The width is defined in meters.
Perimeter - The outside perimeter distance for the section.
d - Type the depth for the section.
bf - Type the width for the section.
tw - Type the web thickness for the section. The thickness is defined in meters.
tf - Type the flange thickness for the section. The thickness is defined in meters.
kdesign - Type the distance from the outer face of the flange to the web toe of the fillet of the
rolled shape or the equivalent distance on the welded section.
kdetail - Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.

140 2D Symbols Marine Mode Reference Data Guide

Member Cross Sections

Cross Section Symbol WedgeWF

The WedgeWF symbol uses the following properties.

2D Symbols Marine Mode Reference Data Guide 141

Member Cross Sections

Angle Right - Define the angle on the right side of the web.
Angle Left - Define the angle on the left side of the web.
Flange Right Width - Define the flange width on the right side.
Flange Left Width - Define the flange width on the left side.
Unit Weight - Type the weight of the section. The unit weight is defined in mass per length pound
per foot (lbm/ft).
Area - Type the cross-section area for the section.
Depth - Type the depth for the section. The depth is defined in meters
Width - Type the width for the section. The width is defined in meters.
Perimeter - The outside perimeter distance for the section.
d - Type the depth for the section.
bf - Type the width for the section.
tw - Type the web thickness for the section. The thickness is defined in meters.
tf - Type the flange thickness for the section. The thickness is defined in meters.
kdesign - Type the distance from the outer face of the flange to the web toe of the fillet of the
rolled shape or the equivalent distance on the welded section.
kdetail - Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX - Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY - Type the vertical distance from the designated member edge to the centroidal axis.
Ixx - Type the moment of inertia for the section's local x-axis.
Zxx - Type the plastic section modulus for the section's local x-axis.
Sxx - Type the section modulus for the section's local x-axis.
Rxx - Type the radius of gyration for the section's local x-axis.
Iyy - Type the moment of inertia for the section's local y-axis.
Zyy - Type the plastic section modulus for the section's local y-axis.
Syy - Type the section modulus for the section's local y-axis.
Ryy - Type the radius of gyration for the section's local y-axis.
J - Type the torsional moment of inertia for the section.
Cw - Type the warping constant for the section.
ro - Type the polar radius of gyration about the shear center.
H - Type the flexural constant for the section.

142 2D Symbols Marine Mode Reference Data Guide

SECTION 9

Profile Cross Sections

Profile cross-section symbols are used in the Molded Forms and Structural Detailing tasks.
The profile cross section symbols are delivered with the software in the [Reference Data
Directory]\SharedContent\Profile Xsections folder. You can create your own custom symbols
using the 2D Symbols utility that is delivered with the software.

In This Section
Cross Section Symbol B ................................................................ 143
Cross Section Symbol BUL2 ......................................................... 145
Cross Section Symbol BUL3 ......................................................... 147
Cross Section Symbol BUT ........................................................... 149
Cross Section Symbol C_SS ......................................................... 150
Cross Section Symbol C_SType ................................................... 151
Cross Section Symbol EA.............................................................. 153
Cross Section Symbol FB .............................................................. 154
Cross Section Symbol HalfR ......................................................... 156
Cross Section Symbol I ................................................................. 157
Cross Section Symbol I_SType ..................................................... 159
Cross Section Symbol P ................................................................ 160
Cross Section Symbol R ................................................................ 162
Cross Section Symbol SB.............................................................. 163
Cross Section Symbol SqTu .......................................................... 164
Cross Section Symbol T ................................................................ 165
Cross Section Symbol T_SType .................................................... 165
Cross Section Symbol UA ............................................................. 167

Cross Section Symbol B

The B bulb angle profile cross section symbol (B.sym) uses the following symbol parameters.

2D Symbols Marine Mode Reference Data Guide 143

Profile Cross Sections

Each symbol parameter is defined and given a default value in the symbol file. Each occurrence of
a symbol bulkloaded into the catalog can be assigned different parameter values.

1 TCR - Top corner radius

2 FL - Flange length

3 Slope - Slope of the bottom of the bulb flange.

Cross Section Symbol BUT

See Also
Cross Sections (see "Member Cross Sections" on page 89)

2D Symbols Marine Mode Reference Data Guide 149

Profile Cross Sections

Cross Section Symbol C_SS

The C_SS profile cross section symbol uses the following properties.

Section Name - Type the section name. This name appears when you label members. The
section name must be unique across the catalog.
Short Name - Type the short name for the section.
Alternate EDI Name - Type the Electronic Data Interchange name for the section. This name is
used when translating sections through CIMsteel. This property is currently not used.
Description - Type a short description if needed.
Area - Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth - Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width - Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter - The outside perimeter distance for the section.
CentroidX - Type the location of the centroid along the local x-axis. The location is defined in
inches or millimeters.
CentroidY - Type the location of the centroid along the local y-axis. The location is defined in
inches or millimeters.
Moment of Inertia about X (Ixx) - Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy) - Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw) - Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx) - Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy) - Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J) - Type the torsional moment of inertia for the section.
Warping Constant (Cw) - Type the warping constant for the section.

150 2D Symbols Marine Mode Reference Data Guide

Profile Cross Sections

Flexural Constant (H) - Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro) - Type the polar radius of gyration about the
shear center.
Radius of Gyration about X axis (Rxx) - Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy) - Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy) - Type the radius of gyration about the local
z-axis. The radius is defined in inches or millimeters.
Plastic Section Modulus about X (Zxx) - Type the plastic section modulus for the section's local
x-axis.
Plastic Section Modulus about Y (Zyy) - Type the plastic section modulus for the section's local
y-axis.
IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, the default value is True.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, the default value is False.

154 2D Symbols Marine Mode Reference Data Guide

Profile Cross Sections

Alternate EDI Name - Type the Electronic Data Interchange name for the section. This name is
used when translating sections through CIMsteel. This property is currently not used.
Description - Type a short description if needed.
Area - Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth - Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width - Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter - The outside perimeter distance for the section.
CentroidX - Type the location of the centroid along the local x-axis. The location is defined in
inches or millimeters.
CentroidY - Type the location of the centroid along the local y-axis. The location is defined in
inches or millimeters.
Moment of Inertia about X (Ixx) - Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy) - Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw) - Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx) - Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy) - Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J) - Type the torsional moment of inertia for the section.
Warping Constant (Cw) - Type the warping constant for the section.
Flexural Constant (H) - Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro) - Type the polar radius of gyration about the
shear center.
Radius of Gyration about X axis (Rxx) - Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy) - Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy) - Type the radius of gyration about the local
z-axis. The radius is defined in inches or millimeters.
Plastic Section Modulus about X (Zxx) - Type the plastic section modulus for the section's local
x-axis.
Plastic Section Modulus about Y (Zyy) - Type the plastic section modulus for the section's local
y-axis.
IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, the default value is True.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, the default value is True.

2D Symbols Marine Mode Reference Data Guide 155

2D Symbols Marine Mode Reference Data Guide 159

Profile Cross Sections

Torsional Moment of Inertia (J) - Type the torsional moment of inertia for the section.
Warping Constant (Cw) - Type the warping constant for the section.
Flexural Constant (H) - Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro) - Type the polar radius of gyration about the
shear center.
Radius of Gyration about X axis (Rxx) - Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy) - Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy) - Type the radius of gyration about the local
z-axis. The radius is defined in inches or millimeters.
Plastic Section Modulus about X (Zxx) - Type the plastic section modulus for the section's local
x-axis.
Plastic Section Modulus about Y (Zyy) - Type the plastic section modulus for the section's local
y-axis.
IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, the default value is True.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, the default value is True.

2D Symbols Marine Mode Reference Data Guide 163

Profile Cross Sections

Moment of Inertia about X (Ixx) - Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy) - Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw) - Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx) - Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy) - Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J) - Type the torsional moment of inertia for the section.
Warping Constant (Cw) - Type the warping constant for the section.
Flexural Constant (H) - Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro) - Type the polar radius of gyration about the
shear center.
Radius of Gyration about X axis (Rxx) - Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy) - Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy) - Type the radius of gyration about the local
z-axis. The radius is defined in inches or millimeters.
Plastic Section Modulus about X (Zxx) - Type the plastic section modulus for the section's local
x-axis.
Plastic Section Modulus about Y (Zyy) - Type the plastic section modulus for the section's local
y-axis.

Cross Section Symbol SqTu

164 2D Symbols Marine Mode Reference Data Guide

Profile Cross Sections

See Also
Cross Sections (see "Member Cross Sections" on page 89)

Cross Section Symbol T

See Also
Cross Sections (see "Member Cross Sections" on page 89)

Cross Section Symbol T_SType

The T_SType profile cross section symbol uses the following properties.

2D Symbols Marine Mode Reference Data Guide 165

Profile Cross Sections

Description - Type a short description if needed.

Area - Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth - Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width - Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter - The outside perimeter distance for the section.
CentroidX - Type the location of the centroid along the local x-axis. The location is defined in
inches or millimeters.
CentroidY - Type the location of the centroid along the local y-axis. The location is defined in
inches or millimeters.
Moment of Inertia about X (Ixx) - Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy) - Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw) - Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx) - Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy) - Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J) - Type the torsional moment of inertia for the section.
Warping Constant (Cw) - Type the warping constant for the section.
Flexural Constant (H) - Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro) - Type the polar radius of gyration about the
shear center.
Radius of Gyration about X axis (Rxx) - Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy) - Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy) - Type the radius of gyration about the local
z-axis. The radius is defined in inches or millimeters.
Plastic Section Modulus about X (Zxx) - Type the plastic section modulus for the section's local
x-axis.
Plastic Section Modulus about Y (Zyy) - Type the plastic section modulus for the section's local
y-axis.
IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, the default value is False.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, the default value is True.

166 2D Symbols Marine Mode Reference Data Guide

Profile Cross Sections

Cross Section Symbol UA

The UA profile cross section symbol uses the following properties.

2D Symbols Marine Mode Reference Data Guide 167

Profile Cross Sections

Flexural Constant (H) - Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro) - Type the polar radius of gyration about the
shear center.
Radius of Gyration about X axis (Rxx) - Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy) - Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy) - Type the radius of gyration about the local
z-axis. The radius is defined in inches or millimeters.
Plastic Section Modulus about X (Zxx) - Type the plastic section modulus for the section's local
x-axis.
Plastic Section Modulus about Y (Zyy) - Type the plastic section modulus for the section's local
y-axis.
IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this
cross-section, the default value is False.
IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this
cross-section, the default value is False.

168 2D Symbols Marine Mode Reference Data Guide

SECTION 10

Edge Features
Edge feature symbols are delivered in the SharedContent share in the [Reference Data
Folder]\SharedContent\Marine Library\Edge Features folder.

Name Description Parameters

Ellipse Available in CutEdge as

an optional item.

Ellipse Along Edge Available in CutEdge as

an optional item.
Use when Edge feature
needs a cut along the
edge.

2D Symbols Marine Mode Reference Data Guide 169

Edge Features

Name Description Parameters

Half Round Available in CutEdge as

a default item.

Half Round Along Edge Available in CutEdge as

an optional item.
Use when the Edge
feature needs a cut along
the edge.

MushRoom Available in CutEdge as

an optional item.

170 2D Symbols Marine Mode Reference Data Guide

Edge Features

Name Description Parameters

MushRoom Along Edge Available in CutEdge as

an optional item.
Use when Edge feature
needs a cut along the
edge.

Scallop Available in CutEdge as

an optional item.
Wide Scallop

Scallop Along Edge Available in CutEdge as

an optional item.
Use when the Edge
feature needs a cut along
the edge.

the bounding profile
UA
B

SnipTopCornerLeft_ER FB For edge

reinforcements
Welded to WebLeft of
the bounding profile

SnipTopCornerRight_ER FB For edge

reinforcements
Welded to WebRight of
the bounding profile

Profile End Cuts

Clip Web Cuts

Used when the assembly connection EndCutType is Clip.

Name Cross- Description Parameters

Sections
Supported

Clip All Welded

184 2D Symbols Marine Mode Reference Data Guide

Profile End Cuts

Cutback Web Cuts

Used when the assembly connection EndCutType is Cutback.

Name Cross-Sections Description Parameters

Supported

Name Cross- Web Cut Parameters

Sections Type Used
Supported
FlangeCutSniped All Clip
Snip

FlangeCutSnipedAngle All Snip

190 2D Symbols Marine Mode Reference Data Guide

Profile End Cuts

Name Cross- Web Cut Parameters

Member End Cuts

End cut symbols for members are delivered in the following locations:
 Web cuts are in the [Reference Data Folder]\SharedContent\Marine Library\Web
Cuts\Members folder.
 Flange cuts are in the [Reference Data Folder]\SharedContent\Marine Library\Flange
Cuts\Members folder.

In This Section
Along-Axis Web Cuts for Members ................................................197
Along-Axis Flange Cuts for Members .............................................220
Web Cuts for Split Members...........................................................248
Flange Cuts for Split Members .......................................................253
Mitered Web Cuts for Members......................................................254
Mitred Flange Cuts for Members ....................................................255
Free-end Web Cuts for Members ...................................................256
Free-end Flange Cuts for Members ...............................................258

Along-Axis Web Cuts for Members

Creates a web cut for a member bounded by the axis curve of the bounding member.
There are separate web cuts for member assembly connections and generic assembly
connections.

2D Symbols Marine Mode Reference Data Guide 197

Member End Cuts

Web-penetrated Center Cuts

Name Cross- Description Parameters

Sections
Supported

Axis_Web_F All Valid boundaries and

orientations present only a
(member)
face to the bounding object.

Web_F
(generic)

Axis_WebTB_F All Valid boundaries and

orientations present only a
(member)
face to the bounding
member. The bounding
member is an H-beam or
WebTB_F similar.
(generic)

Axis_Web_T_F All Valid boundaries and

orientations present only a
(member)
face to the bounding
member. The bounding
member is a channel with
WebT_F the flanges up.
(generic)

Axis_WebB_F All Valid boundaries and

orientations present only a
(member)
face to the bounding
member. The bounding
member is a channel with
WebB_F the flange down.
(generic)

198 2D Symbols Marine Mode Reference Data Guide

Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Axis_Web_ All Valid boundaries and

TE_F_BE orientations present a face,
a top edge, and a bottom
(member)
edge to the bounding
member.
Web_TE_F_BE
(generic)

Web_TE_F_BE_ Rolled Use for an exact fit when

Ellipse sections with both top and bottom
top and bounding edges have a
bottom fillet.
flanges
Valid boundaries and
orientations present a face,
a top edge, and a bottom
edge to the bounding
member.

Web_TE_F_BE_ Rolled Use for an exact fit to the top

EllipseTop sections with edge only when it has a
top flange fillet.
Valid boundaries and
orientations present a face,
a top edge, and a bottom
edge to the bounding
member.

2D Symbols Marine Mode Reference Data Guide 199

Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Web_TE_F_BE_ Rolled Use for an exact fit to the

Ellipse sections with bottom edge only when it
bottom flange has a fillet.
Valid boundaries and
orientations present a face,
a top edge, and a bottom
edge to the bounding
member.

Axis_Web_ All Valid boundaries and

F_BE orientations present a face
and a bottom edge to the
(member)
bounding member.

Web_F_BE
(generic)

Web_F_BE_ All Use for an exact fit to the

Ellipse bottom edge when it has a
fillet.
(generic)
Valid boundaries and
orientations present a face
and a bottom edge to the
bounding member.

200 2D Symbols Marine Mode Reference Data Guide

Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Axis_Web_ All Valid boundaries and

TE_F orientations present a face
and a top edge to the
(member)
bounding member.

Web_TE_F
(generic)

Web_TE_F_ All Use for an exact fit to the top

Ellipse edge when it has a fillet.
(generic) Valid boundaries and
orientations present a face
and a top edge to the
bounding member.

Axis_Web_TF_T_ All Valid boundaries and

Along-Axis Flange Cuts for Members

Flange-penetrated Center Cuts
There are separate web cuts for member assembly connections and generic assembly
connections.

Name Cross- Description Parameters

Sections
Supported

Axis_Flange_F All Valid boundaries and

orientations present only a
(member)
face to the bounding object.

TE_F_BE orientations present a face, a
top edge, and a bottom edge
(member)
to the bounding member.

Flange_TE_F_
BE
(generic)

2D Symbols Marine Mode Reference Data Guide 221

Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Axis_Flange_ All Valid boundaries and

F_BE orientations present a face
and a bottom edge to the
(member)
bounding member.

Flange_F_BE
(generic)

Axis_Flange_ All Valid boundaries and

TE_F orientations present a face
and a top edge to the
(member)
bounding member.

Flange_TE_F
(generic)

Axis_Flange_ All Valid boundaries and

TF_TE_F orientations present a face,
top edge, and top face to the
(member)
bounding member.

Flange Relief orientations present a
Top face and a top edge to the
bounding member. The
bounding member is still
valid if it has a bottom
edge.

Flg Sqr Alg Flg All with no left Valid boundaries and
Rlf Outside Snp flange orientations present a
Top WL face and a top edge to the
bounding member. The
bounding member is still
valid if it has a bottom
edge.

2D Symbols Marine Mode Reference Data Guide 227

Member End Cuts

Name Cross- Description Parameters

Name Cross- Description Parameters

Sections
Supported

Flg Sqr Flange All Valid boundaries and

Relief Bottom orientations present a
face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Flg Sqr Flg Rlf All with no left Valid boundaries and
Outside Snp flange orientations present a
Bottom face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

2D Symbols Marine Mode Reference Data Guide 237

Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Sqr Alg All Valid boundaries and

Straight_LR
(generic)

Axis_Flange_Flush_R All with no left

flange
(member)

Straight_R
(generic)

Axis_Flange_Straight_ All with left

Setback_LR and right
flanges
(member)

StraightSetback_LR
(generic)

244 2D Symbols Marine Mode Reference Data Guide

Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Axis_Flange_Straight_ All with no left

Setback_R flange
(member)

StraightSetback_R
(generic)

Axis_Flange_Sniped_ All with left

Setback_LR and right
flanges
(member)

Member End Cuts

Mitered Web Cuts for Members

Name Cross- Description Parameters

Sections
Supported

MbrMiterWeb All Places a miter straight

end cut.

MbrMiterWeb_S All Places a straight center

S cut and a sniped cut at
top and bottom so that
the flanges of bounding
and bounded do not
meet.

MbrMiterWeb_S All Places a straight cut and

B a sniped cut at bottom so
that the bottom flanges of
bounding and bounded
do not meet.

254 2D Symbols Marine Mode Reference Data Guide

Member End Cuts

Name Cross- Description Parameters

Sections
Supported

MbrMiterWeb_S All Places a straight cut and

T a sniped cut at top so
that the top flanges of
bounding and bounded
do not meet.

MbrMiterWeb_T Circular Places a miter cut for

ube sections circular cross-sections.

Slot A
Slot A class penetrations are not connected to their cross-sections.

Name Cross-Sections Selection Logic Parameters

Supported in the Rules

SlotAA_SM EA None
UA

2D Symbols Marine Mode Reference Data Guide 261

Slots

Name Cross-Sections Selection Logic Parameters

Supported in the Rules

SlotBA_SM B None

SlotFA_SM FB None

262 2D Symbols Marine Mode Reference Data Guide

Slots

Name Cross-Sections Selection Logic Parameters

Supported in the Rules

SlotTA_SM T None
BUT
BUTL2

Slot C
Slot C class penetrations are connected to their cross-sections.

Web Left Connection

Name Cross- Selection Logic Parameters
Sections in the Rules
Supported

SlotAC_L_AAT_DTR EA Non-tight
UA Profile height >
125 mm

2D Symbols Marine Mode Reference Data Guide 263

Slots

Name Cross- Selection Logic Parameters

Sections in the Rules
Supported

SlotAC_L_PAT_DTR EA Non-tight
UA

SlotAC_L_PAT_STR EA Tight
UA

264 2D Symbols Marine Mode Reference Data Guide

Slots

Name Cross- Selection Logic Parameters

Sections in the Rules
Supported

Sections in the Rules
Supported

SlotFC_L_PAT_STR FB Tight

SlotL2C_L_AAT_DTR BUTL2 Non-tight

Profile height >
150 mm

268 2D Symbols Marine Mode Reference Data Guide

Slots

Name Cross- Selection Logic Parameters

Sections in the Rules
Supported

SlotL2C_L_PAT_DTR BUTL2 Non-tight

272 2D Symbols Marine Mode Reference Data Guide

Slots

Name Cross- Selection Logic Parameters

Sections in the Rules
Supported

SlotAC_LT_PAT EA Tight
SlotAC_LT_PAT2 UA

(all use SlotAC_LT_PAT)

SlotBC_LT_PAT B Tight
SlotBC_LT_PAT2

(all use SlotBC_LT_PAT)

2D Symbols Marine Mode Reference Data Guide 273

Slots

Name Cross- Selection Logic Parameters

Sections in the Rules
Supported

SlotFC_LT_PAT FB Tight
SlotFC_LT_PAT2

(all use SlotBC_LT_PAT)

Slot C2
Slot C2 class penetrations are connected to the top of the flange of their cross-sections.

Name Cross- Selection Logic Parameters

Sections in the Rules
Supported

SlotL2C2_T_PTT_STR BUT Tight

SlotL2C2_T_PTT_STR2 BUTL2
SlotTC2_T_PTT_STR
SlotTC2_T_PTT_STR2

(all use
SlotTC2_T_PTT_STR)

274 2D Symbols Marine Mode Reference Data Guide

Slots

Slot I
Slot I class penetrations are connected to the left and right sides of the web of their cross-sections.

Web Left and Web Right Connection

Name Cross- Selection Logic Parameters
Sections in the Rules
Supported

SlotAI EA Available in
catalog, but not
available in
current selection
of SML Slot
rules.

SlotAI_LR_PAAP_STR EA Tight
UA

2D Symbols Marine Mode Reference Data Guide 275

Slots

Name Cross- Selection Logic Parameters

Sections in the Rules
Supported

SlotAI_LR_AAAA_STR EA Non-tight
UA Profile height >
125 mm

SlotBI_LR_PAAP_STR B Tight

276 2D Symbols Marine Mode Reference Data Guide

Slots

Name Cross- Selection Logic Parameters

Sections in the Rules
Supported

SlotBI_LR_AAAA_STR B Non-tight

SlotFI Available in
catalog, but not
available in
current selection
of SML Slot
rules.

SlotFI_LR_PAAP_STR FB Tight

Name Cross- Selection Logic Parameters
Sections in the Rules
Supported

SlotAI_LTR_PAAP_STR EA Tight
UA

SlotBI_LTR_PAAP_STR B Tight

280 2D Symbols Marine Mode Reference Data Guide

Slots

Name Cross- Selection Logic Parameters

Sections in the Rules
Supported

SlotFI_LTR_PAAP_STR FB Tight

SlotL2I_LTR_PAAP_STR BUTL2 Tight

SlotTI_LTR_PAAP_STR BUT Tight

2D Symbols Marine Mode Reference Data Guide 281

Slots

282 2D Symbols Marine Mode Reference Data Guide

SECTION 14

Sketched Features
The sketched feature symbols are delivered with the software in the [Reference Data
Folder]\SharedContent\Sketched Features folder.

Name Description Parameters

Obround Feature Has no smart rule to

select.
Available when placing an
opening/Sketched
feature.

Oval Feature Has no smart rule to

select.
Available when placing an
opening/Sketched
feature.

Rectangle Feature Has no smart rule to

select.
Available when placing an
opening/Sketched
feature.

2D Symbols Marine Mode Reference Data Guide 283

Sketched Features

Name Description Parameters

Round Feature Has no smart rule to

select.
Available when placing an
opening/Sketched
feature.

Square Feature Has no smart rule to

select.
Available when placing an
opening/Sketched
feature.

284 2D Symbols Marine Mode Reference Data Guide

SECTION 15

Openings
The opening symbols are delivered with the software in the [Reference Data Product
Directory]\SharedContent\Openings folder. You can create your own custom opening symbols
using the 2D Symbols utility that is delivered with the software.

In This Section
CircleOpening ................................................................................ 285
OvalOpening .................................................................................. 286
RectangleOpening ......................................................................... 286
SketchOpening .............................................................................. 286
SquareOpening .............................................................................. 287
TriangleOpening ............................................................................ 287

CircleOpening

2D Symbols Marine Mode Reference Data Guide 285

Openings

OvalOpening

RectangleOpening

SketchOpening

286 2D Symbols Marine Mode Reference Data Guide

Openings

SquareOpening

TriangleOpening

2D Symbols Marine Mode Reference Data Guide 287

Openings

288 2D Symbols Marine Mode Reference Data Guide

See Also
Structural Manufacturing (on page 289)

Bevel1 (I-Type)

292 2D Symbols Marine Mode Reference Data Guide

Structural Manufacturing

Bevel2 (V-Type)

Bevel3 (V-Type)

Bevel4 (X-Type)

Bevel5 (Y-Type)

Bevel6 (X-Type with Chamfer)

2D Symbols Marine Mode Reference Data Guide 293

Structural Manufacturing

Bevel7 (X-Type with Chamfer)

Bevel8 (X-Type with Chamfer)

Bevel9 (X-Type with Chamfer)

Bevel10

Structural Manufacturing

PartDirC

PartDirCL

PartDirCR

298 2D Symbols Marine Mode Reference Data Guide

Structural Manufacturing

PartDirL

See Also
Structural Manufacturing (on page 289)

PartDirLL

See Also
Structural Manufacturing (on page 289)

PartDirLLFlangeRR

2D Symbols Marine Mode Reference Data Guide 299

Structural Manufacturing

PartDirR

See Also
Structural Manufacturing (on page 289)

PartDirRR

See Also
Structural Manufacturing (on page 289)

PartDirRRFlangeLL

See Also
Structural Manufacturing (on page 289)

300 2D Symbols Marine Mode Reference Data Guide

Structural Manufacturing

PMFeature

Shrinkage

SMPlateTab

See Also
Structural Manufacturing (on page 289)

2D Symbols Marine Mode Reference Data Guide 301

Structural Manufacturing

UnSpecBevel

WeldTab1

302 2D Symbols Marine Mode Reference Data Guide

Index

MFC 12M e 2006
100% (1)
MFC 12M e 2006
22 pages
Equipment3DSymbolsGuide PDF
No ratings yet
Equipment3DSymbolsGuide PDF
559 pages
Smart3DAutomation Instruction
No ratings yet
Smart3DAutomation Instruction
58 pages
Teste: Peoplesoft 9.1 Financial Management Sales Specialist Assessment
No ratings yet
Teste: Peoplesoft 9.1 Financial Management Sales Specialist Assessment
2 pages
Project Management Guide
No ratings yet
Project Management Guide
451 pages
Interpret Human Piping Spec Guide
100% (1)
Interpret Human Piping Spec Guide
45 pages
TroubleshootingGuide PDF
No ratings yet
TroubleshootingGuide PDF
188 pages
Sp3d Install
50% (2)
Sp3d Install
232 pages
Piping 3D Symbols Guide
100% (1)
Piping 3D Symbols Guide
1,814 pages
Catalog: User's Guide
100% (1)
Catalog: User's Guide
1,013 pages
SPAdapter SPPID
No ratings yet
SPAdapter SPPID
116 pages
3DDOTNETGuide
No ratings yet
3DDOTNETGuide
162 pages
Smartplant P&Id Insulation Manager: User'S Guide
No ratings yet
Smartplant P&Id Insulation Manager: User'S Guide
30 pages
PDS Translation User Guide PDF
No ratings yet
PDS Translation User Guide PDF
63 pages
Hexagon S3D Project Management
No ratings yet
Hexagon S3D Project Management
626 pages
Smartplant 3D: 2009.1 Upgrade Guide
No ratings yet
Smartplant 3D: 2009.1 Upgrade Guide
60 pages
DRUGP
No ratings yet
DRUGP
371 pages
Electrical Reference Data Guide SP3D
No ratings yet
Electrical Reference Data Guide SP3D
68 pages
AVEVA Plant 12 ISODRAFT Reference Manual
No ratings yet
AVEVA Plant 12 ISODRAFT Reference Manual
258 pages
Label Rules - 2011 R1 PDF
No ratings yet
Label Rules - 2011 R1 PDF
24 pages
04 - SP3DNetAPI - Client Services
No ratings yet
04 - SP3DNetAPI - Client Services
13 pages
SP 3 D Upgrade Guide
No ratings yet
SP 3 D Upgrade Guide
41 pages
Drawings Creation Practice Labs - 2009.1
100% (3)
Drawings Creation Practice Labs - 2009.1
69 pages
Pds Guide
No ratings yet
Pds Guide
133 pages
12 SPF Modeling
50% (2)
12 SPF Modeling
5 pages
Smartplant P&Id: Installation and Upgrade Guide
No ratings yet
Smartplant P&Id: Installation and Upgrade Guide
130 pages
CommonGuide PDF
No ratings yet
CommonGuide PDF
672 pages
Export SDNF
No ratings yet
Export SDNF
19 pages
Creating Intergraph Smart 3D DataBases and Configuring
No ratings yet
Creating Intergraph Smart 3D DataBases and Configuring
7 pages
OpenSteel Configuration Guide
No ratings yet
OpenSteel Configuration Guide
71 pages
CSUG
No ratings yet
CSUG
206 pages
SmartPlant 3D Installation Guide
No ratings yet
SmartPlant 3D Installation Guide
117 pages
Delete interDB Macro Records - Design Module - Modules - AVEVA Software Community
No ratings yet
Delete interDB Macro Records - Design Module - Modules - AVEVA Software Community
2 pages
AVEVA Clash Manager User Guide
No ratings yet
AVEVA Clash Manager User Guide
143 pages
Programmable Macro Language
No ratings yet
Programmable Macro Language
28 pages
RIS SQL User's Guide
No ratings yet
RIS SQL User's Guide
312 pages
AVEVA DiagramsInfo PDF
No ratings yet
AVEVA DiagramsInfo PDF
4 pages
SP 3 D Upgrade Guide
No ratings yet
SP 3 D Upgrade Guide
51 pages
TSMP4005 - Structure Symbols PDF
No ratings yet
TSMP4005 - Structure Symbols PDF
56 pages
Data Access Routines User Guide
100% (1)
Data Access Routines User Guide
178 pages
Database Management Reference Manual
No ratings yet
Database Management Reference Manual
251 pages
Aveva Clash Manager Brochures
No ratings yet
Aveva Clash Manager Brochures
2 pages
Anisha Shirdhankar - SPPID Automation
No ratings yet
Anisha Shirdhankar - SPPID Automation
4 pages
Inter Op Publisher User Guide
0% (1)
Inter Op Publisher User Guide
322 pages
05 - SP3DNetAPI - Business Object
No ratings yet
05 - SP3DNetAPI - Business Object
3 pages
Process, Power and Marine Division: Electrical Task
100% (2)
Process, Power and Marine Division: Electrical Task
32 pages
Sp3d Admin Course Content
No ratings yet
Sp3d Admin Course Content
1 page
Pdms Idf File Genaration
No ratings yet
Pdms Idf File Genaration
1 page
Orthographic Drawings Guide Smart Plant 3d
100% (1)
Orthographic Drawings Guide Smart Plant 3d
376 pages
DBIntegrity PDF
No ratings yet
DBIntegrity PDF
621 pages
Manual Upgrade PDMS 12.0 para 12.1
No ratings yet
Manual Upgrade PDMS 12.0 para 12.1
52 pages
SP3D Client Installation
No ratings yet
SP3D Client Installation
2 pages
Hvacag PDF
No ratings yet
Hvacag PDF
72 pages
AutoCAD Plant 3D 2021 for Designers, 6th Edition
From Everand
AutoCAD Plant 3D 2021 for Designers, 6th Edition
Prof. Sham Tickoo
No ratings yet
Hole Management Reference Data Guides m 3 d
No ratings yet
Hole Management Reference Data Guides m 3 d
41 pages
ExportToPDSGuide
No ratings yet
ExportToPDSGuide
70 pages
Smart3D 2016 Grid Structure - Classroom Master
No ratings yet
Smart3D 2016 Grid Structure - Classroom Master
540 pages
TroubleshootingGuide
No ratings yet
TroubleshootingGuide
322 pages
Pds Guide
100% (1)
Pds Guide
128 pages
Geometry Analysis and Repair: User's Guide
No ratings yet
Geometry Analysis and Repair: User's Guide
76 pages
2 D Symbols Guide
No ratings yet
2 D Symbols Guide
620 pages
Hangers and Supports: Data Driven Assembly Configuration Reference
No ratings yet
Hangers and Supports: Data Driven Assembly Configuration Reference
57 pages
Beginners Guide To 100 CAD Exercises - 7
No ratings yet
Beginners Guide To 100 CAD Exercises - 7
1 page
Beginners Guide To 100 CAD Exercises - 6
No ratings yet
Beginners Guide To 100 CAD Exercises - 6
1 page
Beginners Guide To 100 CAD Exercises - 11
No ratings yet
Beginners Guide To 100 CAD Exercises - 11
1 page
Beginners Guide To 100 CAD Exercises - 8
No ratings yet
Beginners Guide To 100 CAD Exercises - 8
1 page
Beginners Guide To 100 CAD Exercises - 4
No ratings yet
Beginners Guide To 100 CAD Exercises - 4
1 page
Aveva Software Customisation Reference Manual RMG
No ratings yet
Aveva Software Customisation Reference Manual RMG
332 pages
Windows Shell Script Programming For The Absolute Beginner - 6
No ratings yet
Windows Shell Script Programming For The Absolute Beginner - 6
1 page
Windows Shell Script Programming For The Absolute Beginner - 2
No ratings yet
Windows Shell Script Programming For The Absolute Beginner - 2
1 page
CompartmentationGuide PDF
No ratings yet
CompartmentationGuide PDF
173 pages
Intergraph Smart Interop Publisher: System Requirements
No ratings yet
Intergraph Smart Interop Publisher: System Requirements
8 pages
Windows Shell Script Programming For The Absolute Beginner - 3
No ratings yet
Windows Shell Script Programming For The Absolute Beginner - 3
1 page
Batch Files
No ratings yet
Batch Files
152 pages
Extracted Pages From AVEVA Bocad Structural Detailing™ 3.1
No ratings yet
Extracted Pages From AVEVA Bocad Structural Detailing™ 3.1
3 pages
AVEVA Bocad Structural Detailing™ 3.1
50% (2)
AVEVA Bocad Structural Detailing™ 3.1
77 pages
List Applicable WPS Piping & Pipeline
No ratings yet
List Applicable WPS Piping & Pipeline
6 pages
Batuan National School Inventory Building 2014
No ratings yet
Batuan National School Inventory Building 2014
23 pages
Avid Studio 2
No ratings yet
Avid Studio 2
7 pages
EFT &amp Surge Waveforms and Simulation Models
No ratings yet
EFT &amp Surge Waveforms and Simulation Models
3 pages
Enter Samsung LTN154P1 L03
No ratings yet
Enter Samsung LTN154P1 L03
13 pages
Review On Design of Agitator
No ratings yet
Review On Design of Agitator
4 pages
Air Vacuum & Blow Gun Kit
No ratings yet
Air Vacuum & Blow Gun Kit
31 pages
7 CAAT-AIR-GM03 Guidance-Material-for-Foreign-Approved-Maintenance-Organization - I3R0 - 30oct2019 PDF
No ratings yet
7 CAAT-AIR-GM03 Guidance-Material-for-Foreign-Approved-Maintenance-Organization - I3R0 - 30oct2019 PDF
59 pages
BROCHURE Xylem - Pump Selection Guide 0412
No ratings yet
BROCHURE Xylem - Pump Selection Guide 0412
82 pages
Bubble Sort: Filter - None Edit Play - Arrow Brightness - 4
No ratings yet
Bubble Sort: Filter - None Edit Play - Arrow Brightness - 4
5 pages
777 Groundwork Instruments Transcript PDF
No ratings yet
777 Groundwork Instruments Transcript PDF
8 pages
Operating Fluids
No ratings yet
Operating Fluids
9 pages
IMMT 211 Principles of Mechanical Maintenance - LAB MANUAL
No ratings yet
IMMT 211 Principles of Mechanical Maintenance - LAB MANUAL
162 pages
6es7221 1BH22 0xa0
No ratings yet
6es7221 1BH22 0xa0
2 pages
MOSFET Questions
100% (2)
MOSFET Questions
23 pages
Etched City PDF
0% (3)
Etched City PDF
2 pages
Cep/Oel/Pbl & Semester Projects Details of Spring-2022
No ratings yet
Cep/Oel/Pbl & Semester Projects Details of Spring-2022
1 page
Glasses, ceramices and composites_Class notes
No ratings yet
Glasses, ceramices and composites_Class notes
12 pages
3COM OS Switch 4500 V3.03.02p15 Release Notes
No ratings yet
3COM OS Switch 4500 V3.03.02p15 Release Notes
74 pages
Dell Proforma
No ratings yet
Dell Proforma
5 pages
T101 Drilling Machine
No ratings yet
T101 Drilling Machine
4 pages
2720 Anaerobic Sludge Digester Gas Analysis : 1. Selection of Method
No ratings yet
2720 Anaerobic Sludge Digester Gas Analysis : 1. Selection of Method
5 pages
2017 Lab 3 Datasheet Dotmatrix TOP-CA-1088BS
No ratings yet
2017 Lab 3 Datasheet Dotmatrix TOP-CA-1088BS
7 pages
Auxiliary System Charge Air System: Sterling and Wilson Co-Gen Solutions
No ratings yet
Auxiliary System Charge Air System: Sterling and Wilson Co-Gen Solutions
17 pages
DNV Clean Ts612
No ratings yet
DNV Clean Ts612
26 pages
Aqua PDF
No ratings yet
Aqua PDF
4 pages
Suzlon S88 2.1MW Product Brochure
No ratings yet
Suzlon S88 2.1MW Product Brochure
4 pages
API 6A Type 6B & 6BX Flanges
No ratings yet
API 6A Type 6B & 6BX Flanges
31 pages
CatalogoDiferencialScaniaRP731 PDF
No ratings yet
CatalogoDiferencialScaniaRP731 PDF
3 pages