Download from: https://truckmanualshub.

com/category/trucks/freightliner/

Freightliner Business Class M2 Automated-Manual Transmissions

Fault Code Guide

Fault Code Guide (MID 130 SIDs)

SID FMI Text Message Failure Reason

18 02 Prim Selector Erratic The shift lever does not shift gears.
33 03 MultiPress Ind Short Hi The hydraulic pressure sensor circuit is shorted to power.
33 04 MultiPress Ind Short Lo The hydraulic pressure sensor circuit is shorted to ground.
33 05 MultiPress Ind OPEN The hydraulic pressure sensor circuit is open.
52 05 Hydraulic Sys OPEN The hydraulic pump circuit is open.
The hydraulic pressure does not increase even though the
52 07 Hydraulic Sys NoRESPONSE
hydraulic pump is activated.
52 11 Clutch Act Not Known The hydraulic pump temperature is too high.
55 00 Clutch Act HIGH The clutch is too hot.
55 07 Clutch Act NoRESPONSE The clutch does not operate properly.
55 13 Clutch Act Calibrate The clutch needs to be calibrated.
231 02 SAE J1939 Datalink Erratic The J1939 datalink is not communicating properly.
231 09 SAE J1939 Datalink UPDATE The J1939 datalink has timed out.
The J1939 datalink is not communicating with the
231 12 SAE J1939 Datalink Bad
transmission.
251 00 POWER SUPPLY HIGH The power supply voltage is too high.
251 01 POWER SUPPLY Low The power supply voltage is too low.
There is no power to the transmission with the engine
251 05 POWER SUPPLY OPEN
running.
251 14 POWER SUPPLY RSRVD The power supply is not properly grounded.
253 02 Calibration Memory Erratic The transmission needs to be recalibrated.
253 12 Calibration Memory Bad The transmission needs to be recalibrated.
253 13 Calibration Memory Calibrate The transmission needs to be recalibrated.
253 14 Calibration Memory RSRVD The transmission needs to be recalibrated.

SID FMI Text Message Failure Reason

254 04 Controller Short Lo The TCU is shorted to ground.
254 05 Controller OPEN The TCU has an open circuit.
254 11 Controller Not Known The TCU AUTO mode software module has an error.
254 12 Controller Bad The TCU has a hardware problem.
254 13 Controller Calibrate The TCU has a software memory problem.

Download from https://truckmanualshub.com

Fault Code Guide (MID 130 PIDs)

PID FMI Text Message Failure Reason

33 02 Erratic The clutch position sensor gives invalid data.
33 03 Short Hi The clutch position sensor circuit is shorted to power.
33 04 Short Lo The clutch position sensor circuit is shorted to ground.
33 05 OPEN The clutch position sensor circuit is open.
The clutch position sensor gives incorrect resistance
33 14 RSRVD
readings.
59 02 Shift FNGR Gear Erratic The shift rod position sensor gives invalid data.
59 03 Shift FNGR Gear Short Hi The gear position sensor circuit is shorted to power.
59 04 Shift FNGR Gear Short Lo The gear position sensor circuit is shorted to ground.
59 05 Shift FNGR Gear OPEN The gear position sensor circuit is open.
59 14 Shift FNGR Gear RSRVD The gear position sensor gives incorrect resistance readings.
60 02 Shift FNGR Rail Erratic The rail position sensor circuit gives invalid data.
60 03 Shift FNGR Rail Short Hi The rail position sensor circuit is shorted to power.
60 04 Shift FNGR Rail Short Lo The rail position sensor circuit is shorted to ground.
60 05 Shift FNGR Rail OPEN The rail position sensor circuit is open.
60 14 Shift FNGR Rail RSRVD The rail position sensor gives incorrect resistance readings.
The output shaft speed sensor is not providing accurate
64 09 Dir Switch Update
directional information.
The output shaft speed sensor is not providing accurate
64 11 Dir Switch Not Known
directional information.
158 00 Volts (BattSw) HIGH The voltage in the ignition power circuit is too high.
158 01 Volts (BattSw) Low The voltage in the ignition power circuit is too low.
161 02 In shaft SPEED Erratic The input shaft speed sensor circuit gives invalid data.
161 03 In shaft SPEED Short Hi The input shaft speed sensor circuit is shorted to power.
161 04 In shaft SPEED Short Lo The input shaft speed sensor circuit is shorted to ground.
161 05 In shaft SPEED OPEN The input shaft speed sensor circuit is open.
The input shaft speed sensor circuit is broadcasting an
161 08 In shaft SPEED Update
abnormal frequency.

PID FMI Text Message Failure Reason

162 02 RANGE Selected Erratic The transmission is not properly calibrated.
163 02 RANGE Attained Erratic The gears do not shift properly.
One or both of the output shaft speed sensor circuits give
191 02 OUTPUT SPEED Erratic
invalid data.
One or both of the output shaft speed sensor circuits are
191 05 OUTPUT SPEED OPEN
open.
There is no signal coming from one or both output shaft
191 08 OUTPUT SPEED SIGNAL
speed sensors.
191 14 OUTPUT SPEED RSRVD The output shaft speed sensor is providing invalid data.

For a list of proprietary fault codes viewable on ServiceLink

Download from https://truckmanualshub.com

 AGS Proprietary Fault Codes (J1708)
Fault Code Description
3000109 High voltage supply voltage—external (connector X1/12 and X1/15)
3000113 High voltage ignition key line—external (connector X1/9)
3000209 Low voltage supply voltage—external (connector X1/12 and X1/15)
3000213 Low voltage ignition key line—external (connector X1/9)
3001210 EEPROM parameter values error—internal
3001510 Clutch displacement control module parameter error—internal
3001781 Clutch calibration offset off limit—internal
3002009 Open load supply voltage—external (connector X1/12 and X1/15)
3002016 Open load/Short circuit VCC temperature sensor circuit board—internal
3002017 Open load/Short circuit VCC temperature sensor pump—internal
3002116 Short circuit GND temperature sensor circuit board—internal
3002117 Short circuit GND temperature sensor pump—internal
3002214 Short circuit VCC peripherals supply—external (connector X2/15)
3003001 EBC1 message timeout—external (J1939)
3003101 EEC1 message timeout—external (J1939)
3003201 EEC2 message timeout—external (J1939)
3003301 EEC3 message timeout—external (J1939)
3003401 ERC1 message timeout—external (J1939)
3003501 Wheel speed information message timeout—external (J1939)
3003601 CruiseControl (VCU) message timeout—external (J1939)
3003701 CruiseControl (bulkhead) message timeout—external (J1939)
3003801 Engine configuration message timeout—external (J1939)
3003901 Retarder configuration message timeout—external (J1939)
3004001 Component identification message timeout—external (J1939)
3004101 PTO information message timeout—external (J1939)
3006101 Incorrect engine data—external (J1939)
3006201 Timeout converted engine data for clutch module (low priority)—internal
3006701 Incorrect retarder data—external (J1939)
3006801 Incorrect ABS data—external (J1939)
3006901 Incorrect internal data—internal
3007001 Incorrect clutch module data—internal
3007101 Incorrect automated gear shift module data—internal
3007201 Incorrect internal data—internal
3008881 Clutch overload—internal
3009280 Plausibility error actual transmission gear ratio—internal
3009710 Test software—internal
3009810 Test electronic—internal

Download from https://truckmanualshub.com

 AGS Proprietary Fault Codes (J1708)
Fault Code Description
3009910 Test bench mode activated—internal
3010390 Automatic module: signal group cruise control / retarder—internal
3010690 Automatic module: signal output speed—internal
3010790 Automatic module: signal group MR—internal
3010890 Automatic module: signal group gear ratio—internal
3010990 Automatic module: learning values engine—internal
3011081 Plausibility error intended clutch position can not be reached within specified time—internal
3011090 Automatic module: learning values transmission—internal
3011310 Clutch calibration data missing/error—internal
3011410 Clutch parameter error—internal
3011590 Automatic module: signal group shifting time—internal
3011690 Automatic module: signal group ABS—internal
3011790 Automatic module: signal group pedal activation—internal
3011890 Automatic module: signal group lever—internal
3011990 Automatic module: error target system—internal
3012014 Open load peripherals supply—external (connector X2/15)
3012019 Plausibility error valve relay V-V2 on—internal
3012035 Open load power stage solenoid valve (clutch open 1)—internal
3012036 Open load power stage solenoid valve (clutch open 2)—internal
3012037 Open load power stage solenoid valve (clutch close 1)—internal
3012038 Open load power stage solenoid valve (clutch close 2)—internal
3012050 Open load speed sensor transmission output (DZ1)—external (connector X2/14)
3012051 Open load speed sensor transmission input—external (connector X2/11)
3012052 Open load speed sensor transmission output (D3)—external (connector X2/9)
3012090 Automatic module: system identification gearshift module—internal
3012114 Short circuit to GND peripherals supply—external (connector X2/15)
3012118 Plausibility error valve relay V-V1 off—internal
3012119 Plausibility error valve relay V-V2 off—internal
3012136 Short circuit GND power stage solenoid valve (clutch open 2)—internal
3012138 Short circuit GND power stage solenoid valve (clutch close 2)—internal
3012151 Short circuit GND speed sensor transmission input—external (connector X2/11
3012251 Short circuit VCC speed sensor transmission input—external (connector X2/11)
3012461 Hydraulic level too low external—external
3016201 Timeout converted engine data for clutch module (medium priority)—internal
3016401 Timeout driving direction information—internal
3016501 Timeout internal communication shift module to clutch module (medium priority)—internal

Download from https://truckmanualshub.com

 AGS Proprietary Fault Codes (J1708)
Fault Code Description
3018681 Plausibility error clutch open request while inlet valves are closed—internal
3018781 Plausibility error clutch open request while outlet valves are closed—internal
3019480 Plausibility error driving direction—internal
3019621 SmartShift lever data invalid—external (connector X1/8, X1/11, X1/14)
3019650 Tooth signal interruption speed sensor transmission output (DZ1)—external (connector X2/14)
3019651 Tooth signal interruption speed sensor transmission input—external (connector X2/11)
3019652 Tooth signal interruption speed sensor transmission output (D3)—external (connector X2/9)
3020110 High voltage distance sensor supply—internal
3020111 Power supply high voltage—external (connector X3/1)
3020210 Low voltage distance sensor supply—internal
3020211 Power supply low voltage—external (connector X3/1)
3021010 Flash checksum error—internal
3021110 EEPROM calibration values error—internal
3021610 Clutch displacement offset failure—internal
3022011 Supply voltage open load—external (connector X3/1)
3022012 Open load GND connection—external (connector X1/18 and X1/21)
3022015 Open load pressure sensor signal—internal
3022018 Plausibility error valve relay V-V1 on—internal
3022020 Open load GND pump motor—external (connector X3/2)
3022030 Open load power stage solenoid valve (selection direction R)—internal
3022031 Open load power stage solenoid valve (selection direction 5/6)—internal
3022032 Open load power stage solenoid valve—internal
3022033 Open load power stage solenoid valve (gear direction 1,3,5)—internal
3022034 Open load power stage solenoid valve (pressure regulation)—internal
3022041 Open load distance sensor (gear)—internal
3022042 Open load distance sensor (selection)—internal
3022044 Open load distance sensor (clutch)—internal
3022060 Open loop power stage pump motor—internal
3022115 Short circuit GND pressure sensor signal—internal
3022130 Short circuit GND power stage solenoid valve (selection direction R)—internal
3022131 Short circuit GND power stage solenoid valve (selection direction 5/6)—internal
3022132 Short circuit GND power stage solenoid valve (gear direction R,2,4,6)—internal
3022133 Short circuit GND power stage solenoid valve (gear direction 1,3,5)—internal
3022134 Short circuit GND power stage solenoid valve (pressure regulation)—internal
3022135 Short circuit GND power stage solenoid valve (clutch open 1)—internal
3022137 Short circuit GND power stage solenoid valve (clutch close 1)—internal

Download from https://truckmanualshub.com

 AGS Proprietary Fault Codes (J1708)
Fault Code Description
3022141 Short circuit GND distance sensor (gear)—internal
3022142 Short circuit GND distance sensor (selection)—internal
3022144 Short circuit GND distance sensor (clutch)—internal
3022160 Short circuit GND power stage pump motor—internal
3022215 Short circuit VCC pressure sensor signal—internal
3022241 Short circuit VCC distance sensor (gear)—internal
3022242 Short circuit VCC distance sensor (selection)—internal
3022244 Short circuit VCC distance sensor (clutch)—internal
3022317 Over temperature power stage pump motor—internal
3022590 Automatic module: no signal vehicle speed—internal
3022690 Automatic module: signal group MR (high priority)—internal
3022790 Automatic module: signal group gear ratio (high priority)—internal
3022890 Automatic module: learning values engine (high priority)—internal
3022990 Automatic module: learning values transmission (high priority)—internal
3024341 Erratic distance sensor (gear)—internal
3024342 Erratic distance sensor (selection)—internal
3024344 Erratic distance sensor (clutch)—internal
3024441 Wrong coil resistance value distance sensor (gear)—internal
3024442 Incorrect coil resistance value distance sensor (selection)—internal
3024444 Incorrect coil resistance value distance sensor (clutch)—internal
3024610 Timeout displacement sensor value—internal
3026001 CAN bus off—external (connector X1/13 and X1/7)
3026301 Timeout converted engine data for clutch module (high priority)—internal
3026501 Timeout internal communication shift module to clutch module (high priority)—internal
3027401 No J1939 communication—internal / external (connector X1/13 and X1/7)
3027501 Timeout internal communication shift module to clutch module (high priority)—internal
3028581 Clutch displacement control failure—internal
3029180 No calculation of redundant transmission output speed—internal
3029380 Incorrect transmission type—internal
3029580 Plausibility error pressure build up—internal

https://truckmanualshub.com/category/trucks/freightliner/

Download from https://truckmanualshub.com

Download from https://truckmanualshub.com