SPECIFICATIONS

700-25 Flow Meter

DESIGN
The 700-25 flow meter has a simple and efficient meter design consisting of a housing
and three rotors that rotate in unison within the measuring chamber. The absence of
wear, from no metal-to-metal contact inside the chamber, eliminates any deterioration in
accuracy and provides a long service life. The rotors are supported by bearings inserted
into two bearing plates, where at the end of each rotor shaft is a timing gear. The timed
rotation between each rotor is then transferred through the calibration adjuster to the
register, which will then give a consistent and superior measurement of accuracy.

FLOW ILLUSTRATION

Total Control Systems PERFORMANCE FEATURES

rotary positive dis- LOW PRESSURE DROP: will operate on gravity flow or pump pressure
placement flow meters SUSTAINED ACCURACY: no metal-to-metal contact inside the measuring cham-
offer reliable and pre- ber means minimal wear and deterioration in accuracy over time, fewer recalibrations
and longer service life.
cise measurement solu-
tions for preset deliv- VISCOSITY RANGE: will accurately measure liquids up to 1,500,000 SSU
(325,000 CPS)
ery, flow rate control,
blending and custody LINEARITY:
5:1 Turndown - capable of ± 0.100% of maximum nominal flow rate
transfer of vehicle or 10:1 Turndown - capable of ± 0.125% of maximum nominal flow rate
wholesale measurement 15:1 Turndown - capable of ± 0.150% of maximum nominal flow rate
applications. REPEATABILITY: capable of 0.02% over the entire range of flow
Data provided from test conditions where all system variables were constant. The results are based on the
700 series flow meter and Veeder Root mechanical registration, using 32 SSU testing fluid.

REGULATORY: Meets NIST, USA military and other international weights and
measures accuracy requirements.

OPERATING SPECIFICATIONS
DESIGN TYPE: Positive Displacement Rotary Abutment
INDUSTRIES SERVED
• Petroleum Products FLOW CAPACITY: 10 GPM to 150 GPM
• Alternative Fuels 38 LPM to 567 LPM
• Aviation Fuels VISCOSITY: Up to 225 SSU at rated capacity.
• Agricultural Chemicals
• Petrochemicals PRESSURE RATING: 150 PSI
10.5 BAR
• Textiles
• Foods and Beverages TEMPERATURE RATING: -40°F to 160°F
• Paints and Coatings -40°C to 71°C
• Pharmaceuticals CONNECTIONS: 2” NPT Standard. Optional BSPT, Slip Weld,
• Printing Inks ANSI and DIN flanges are available upon request..
METER TYPES
SPA Standard Petroleum (Aviation)
For metering refined petroleum products; such as Regular and Unleaded Gasoline, Diesel, Bio-Diesel, Avia-
tion Gasoline, Jet Fuel, Naptha, Kerosene, etc.

SPD Standard Petroleum (Ductile Iron)

For metering refined petroleum products; such as Ethanol, Methanol, Regular and Unleaded Gasoline, Diesel,
Bio-Diesel, Natural Gasoline, Vegetable Oils, Kerosene, etc.

MATERIALS OF CONSTRUCTION

Meter Bearing Bearing Timing Internal

Housing Rotors Journals Seals
Type Plates Sleeves Gears Hardware

Anodized Anodized Carbon Hardchrome Stainless Stainless

SPA Ni-Resist Viton ®
Aluminum Aluminum Graphite Stainless Steel Steel Steel

Ductile Stainless Carbon Hardchrome Stainless Stainless Teflon ® &

SPD Ni-Resist
Iron Steel Graphite Stainless Steel Steel Steel Simriz ®
Viton is a registered trademark of E.I. Dupont de Nemours & Co.
Teflon is a registered trademark of Dupont Dow Elastomers
Simriz is a registered trademark of Freudenberg-NOK

REGISTRATION OPTIONS
COUNTER REGISTER ELECTRONIC METER REGISTER MICROSWITCH
Liquid measurement volume indica- Digital liquid measurement volume indi- Mechanical signal from the Veeder
tion, using a 5 digit large numeral cation that offers multiple functions to Root preset counter converted into
reset display and an 8 digit non-reset enhance the flow meter's accuracy and an electrical or pneumatic signal to
totalizer. Electronic or mechanical accountability. Most electronic registra- provide control of remotely located
meter counter register is available. U. tion are available with rate of flow indi- valve, pump, and other system re-
S. or Imperial Gallons, Liters, Deka- cation, pulse output, valve control, lated equipment.
liter, Barrels, pounds, etc. RS232 and RS485 communication, cur-
rency and temperature compensation. COUNTER EXTENSION
COUNTER PRESET Raises the elevation of the counter
Select predetermined volume for pre- PULSE TRANSMITTER registration for easy visibility or to
cise batch control, utilizing preset The electronic pulse signal output con- protect from high temperatures.
control valve. Mechanical or elec- verts the register counter volume per unit Counter Extension is required for
tronic preset counters or batch con- value into a electrical pulse stream. The temperatures more than 180°C
trollers are available. electronic pulse stream can be transmit- (82°C).
ted to other electronic controllers for rate
TICKET PRINTER of flow, volume indication, additive in- RATE OF FLOW INDICATOR
Provides an imprinted ticket record jection or data acquisition. Mechanical or digital indicator
of each delivery transaction. Accu- displays the volume at which the
mulative or Zero-Start, Face down or TEMPERATURE COMPENSATION liquid is flowing through the flow
Face Up mechanical ticket printers Automatically corrects changes in vol- meter.
available. Electronic slip or roll ume caused by liquid temperature varia-
printers available for use with vari- tions, during metered delivery. Normally SWIVEL
ous electronic registration. corrects net volume or mass to 60°F Allows mechanical registration to
(15°C) based on the product’s coefficient be rotated 360°. Designed for the
of expansion, API or specific gravity. Veeder Root counter register and
ticket printer only.
METER ACCESSORIES
AIR ELIMINATOR ELECTRONIC PRESET VALVE
A float and reed valve operated design senses A normally closed two-stage piston preset
and removes free air or vapor before it can valve for use with electronic relay control.
enter the flow meter. Required for custody The solenoid valves are available in 12 or 24
transfer applications to ensure the most pre- VDC, or 110 VAC coils. Stainless steel or
cise measurement. brass pilot valves are also available. Dimen-
sionally interchangeable with the mechanical
STRAINER valve.
A 90° strainer provides protection from de-
bris entering into the flow meter. Must be PNEUMATIC PRESET VALVE
mounted in vertical position when assembled Air actuated, normally closed two-stage pis-
with air eliminator. Stainless steel screens are ton preset valve for use in systems with air
available in 40, 80, 100 & 200 mesh, and supply. Dimensionally interchangeable with
0.050 perforation. the mechanical valve.

HIGH CAPACITY STRAINER AIR CHECK VALVE

An offset 90° strainer and air eliminator The spring loaded check valve provides 15
assembly designed for use in applications PSI differential pressure to increase air elimi-
where a high volume of free air may poten- nator efficiency and to prevent metering
tially enter the measurement system. Recom- compressed air produced by a positive dis-
mended for mobile fuel delivery systems to placement pump during a stripping operation
pass product depletion (split compartment) of the vessel being emptied.
testing.
WAFER CHECK VALVE
MECHANICAL PRESET VALVE In-line check valve is mounted between the
A normally closed, hydraulically balanced strainer and meter assembly to help increase
piston control valve allows for auto-batch air eliminator efficiency by creating addi-
preset deliveries. The right angle, two–stage tional back pressure.
control valve is mechanically linked to
Veeder Root Preset Counter.

ASSEMBLY COMBINATIONS
GROUP COMBINATIONS
2 Meter & Register
3 Meter, Register & Ticket Printer
4 Meter, Register, Air Eliminator & Strainer
4R Meter, Register, Air Eliminator & High Volume Strainer
5 Meter, Register & Strainer
6 Meter, Register, Ticket Printer, Air Eliminator & Strainer
6R Meter, Register, Ticket Printer, Air Eliminator & High Volume Strainer
7 Meter, Register, Printer, & Strainer GROUP 2 GROUP 4
8 Meter, Register, Preset & Valve
9 Meter, Register, Ticket Printer, Preset & Valve
10 Meter, Register, Preset, Valve, Air Eliminator & Strainer
10R Meter, Register, Preset, Valve, Air Eliminator & High Volume Strainer
11 Meter, Register, Ticket Printer, Preset, Valve, Air Eliminator & Strainer
11R Meter, Register, Ticket Printer, Preset, Valve, Air Eliminator & High Volume
Strainer
12 Meter, Register, Preset, Valve & Strainer
13 Meter, Register, Ticket Printer, Preset, Valve & Strainer
GROUP 8 GROUP 10

METER ORIENTATION
A Meter Assembly with Veeder Root Registration
B Meter assembly less Veeder Root Registration
C Meter Assembly for use with Electronic Registration
(less calibration adjuster)
D Meter Assembly with direct drive pulse transmitter
Meter A Meter B Meter C Meter D
(700-20SP10AT) (700-20SP10RBX) (700-20SP10RCXA) (700-30SP2DX)
 TCS900009
700-25 DIMENSIONS

700-25 NET WEIGHTS IN POUNDS (KILOGRAMS)

Air Air Eliminator
Meter Flow Register Preset Ticket Electronic Mechanical Air Check
Eliminator/ /High Volume Strainer
Type Meter Counter Counter Printer Valve Valve Valve
Strainer Strainer

24 12 10 12 17 32 9 13 7 7
SPA
(11.8) (5.4) (4.5) (5.4) (7.7) (14.5) (4.1) (5.9) (3.2) (3.2)

52 12 10 12 39 19 18 16
SPD N/A N/A
(22.7) 5.4 4.5 5.4 (17.8) (8.6) (8.2) (7.3)

WARRANTY
Total Control Systems 700 rotary meters and accessory components sold to the original purchaser for a period of TWELVE (12)
months from installation or EIGHTEEN (18) months from the date of shipment, to be free, under normal use and service, from de-
fects in material and workmanship. If a warranty dispute occurs the DISTIBUTOR may be required to provide proof of date of
sale. Defects occurring within the stated warranty period, will be repaired or replaced, at TCS’s option; provided that part or parts
are returned to TCS transportation changes prepaid, and TCS’s examination discloses the parts or workmanship to have been de-
fective upon delivery to the purchaser. All repaired or warranted meters will be shipped Ex-works Fort Wayne, Indiana. Total
Control Systems shall not be liable for consequential damages, whether or not arising out of warranty, negligence or otherwise.
NOTE: The above warranty applies only to Total Control Systems, Fort Wayne, Indiana manufactured products. Private label and
OEM engineered products are specifically excluded from the above warranty. Consult factory for non-TCS manufacturer’s war-
ranty.

TOTAL CONTROL SYSTEMS

2515 Charleston Place
Fort Wayne, Indiana 46808 USA
(800) 348-4753 • (260) 484-0382
Fax: (260) 484-9230
[email protected] • www.tcsmeters.com “Made in the U.S.A.”

© 2006 Total Control Systems