ESO 201A: Thermodynamics

CHAPTER 8: EXERGY

Instructor: Dr. Ashoke De

Department of Aerospace Engineering
http://home.iitk.ac.in/~ashoke
Email: [email protected]
 Objectives
 Examine the performance of engineering devices in light
of the second law of thermodynamics.
 Define exergy, which is the maximum useful work that
could be obtained from the system at a given state in a
specified environment.
 Define reversible work, which is the maximum useful
work that can be obtained as a system undergoes a
process between two specified states.
 Define the exergy destruction, which is the wasted work
potential during a process as a result of irreversibilities.
 Define the second-law efficiency.
 Develop the exergy balance relation.
 Apply exergy balance to closed systems and control
volumes.
2
EXERGY: WORK POTENTIAL OF ENERGY
The useful work potential of a
given amount of energy at some
specified state is called exergy,
which is also called the availability
or available energy.

A system is said to be in the dead

state when it is in thermodynamic
equilibrium with the environment it
is in.

3
A system delivers the maximum possible work as it undergoes a reversible process
from the specified initial state to the state of its environment, that is, the dead state.
This represents the useful work potential of the system at the specified state and is
called exergy.
Exergy represents the upper limit on the amount of work a device can deliver without
violating any thermodynamic laws.

4
Exergy (Work Potential) Associated The exergies of kinetic and
with Kinetic and Potential Energy potential energies are equal to
themselves, and they are entirely
available for work.

Exergy of potential energy:

Exergy of kinetic energy:

5
REVERSIBLE WORK AND IRREVERSIBILITY
Reversible work Wrev: The maximum amount of
useful work that can be produced (or the
minimum work that needs to be supplied) as a
system undergoes a process between the
specified initial and final states.
As a closed
system expands,
some work needs
to be done to push
the atmospheric
air out of the way
(Wsurr).

The difference between

reversible work and
actual useful work is the
irreversibility.

For constant-volume
systems, the total
actual and useful
works are identical
(Wu = W). 6
The Rate of Irreversibility of a
Heat Engine

7
Irreversibility during the
Cooling of an Iron Block

8
SECOND-LAW EFFICIENCY

9
General definition of exergy efficiency:

10
Second-Law Efficiency of Resistance Heaters

11
EXERGY CHANGE OF A SYSTEM
Exergy of a Fixed Mass: Nonflow
(or Closed System) Exergy

Exergy of a closed system

12
 Closed system
exergy per unit
mass

Exergy
change of
a closed
system

When the properties of a system are

not uniform, the exergy of the system is

13
Exergy of a Flow Stream: Flow (or Stream) Exergy

Exergy of flow energy

Flow
exergy
Exergy change of flow

14
15
 Work Potential of
Compressed Air in a Tank

100kPa, 300K

16
Exergy Change During a
Compression Process

17
EXERGY TRANSFER BY
HEAT, WORK, AND MASS

Exergy by Heat Transfer, Q

Exergy transfer
by heat

When temperature is
not constant

18
Exergy Transfer by Work, W

Exergy Transfer by Mass, m

19
THE DECREASE OF EXERGY PRINCIPLE
AND EXERGY DESTRUCTION

The exergy of an isolated system during a process always decreases or, in

the limiting case of a reversible process, remains constant. In other words, it
never increases and exergy is destroyed during an actual process. This is
known as the decrease of exergy principle. 20
Exergy Destruction

Exergy destroyed is a positive quantity for

any actual process and becomes zero for a
reversible process.
Exergy destroyed represents the lost work
potential and is also called the
irreversibility or lost work.
Can the exergy change
of a system during a
process be negative?

Consider heat transfer from a system to

its surroundings. How do you compare
exergy changes of the system and the
surroundings? 21
EXERGY BALANCE: CLOSED SYSTEMS

The exergy change of

a system during a
process is equal to the
difference between the
net exergy transfer
through the system
boundary and the
exergy destroyed
within the system
boundaries as a result
of irreversibilities.

22
 The heat transfer to
a system and work
done by the system
are taken to be
positive quantities.

Qk is the heat transfer through the boundary at temperature Tk at location k.

Exergy Exergy
balance for destroyed
a closed outside system
system boundaries can
when heat be accounted for
transfer is by writing an
to the exergy balance
system and on the extended
the work is system that
from the includes the
system. system and its
immediate
surroundings. 23
General Exergy Balance for Closed Systems

24
Exergy Destruction during Heat Conduction

25
 Exergy Destruction During Expansion of Steam
The exergy balance applied on the extended
system (system + immediate surroundings)
whose boundary is at the environment
temperature of T0 gives

Alternative method of exergy

destruction calculation:

26
Dropping a Hot Iron Block into Water

27
Work Potential of Heat Transfer Between Two Tanks

28
EXERGY BALANCE: CONTROL VOLUMES

The rate of exergy change within the

control volume during a process is
equal to the rate of net exergy transfer
through the control volume boundary
by heat, work, and mass flow minus the
rate of exergy destruction within the
boundaries of the control volume.

29
Exergy Balance for Steady-Flow Systems
Most control volumes encountered in practice such as turbines, compressors, nozzles,
diffusers, heat exchangers, pipes, and ducts operate steadily, and thus they experience
no changes in their mass, energy, entropy, and exergy contents as well as their volumes.
Therefore, dVCV/dt = 0 and dXCV/dt = 0 for such systems.

30
Reversible Work
The exergy balance relations presented above can be used to
determine the reversible work Wrev by setting the exergy destroyed
equal to zero. The work W in that case becomes the reversible work.

The exergy destroyed is zero only for a reversible process, and

reversible work represents the maximum work output for work-
producing devices such as turbines and the minimum work input for
work-consuming devices such as compressors.

31
Second-Law Efficiency of Steady-Flow Devices
The second-law efficiency of various steady-flow devices can be determined from its
general definition, II = (Exergy recovered)/(Exergy expended). When the changes in
kinetic and potential energies are negligible and the devices are adiabatic:

Turbine

Compressor

Heat
exchanger

Mixing
chamber

32
Second-law analysis of a steam turbine

33
Exergy Destroyed During Mixing 190 kJ/min
of Fluid Streams

10C
150C 70C
200 kPa

= 20C

34
Charging a Compressed Air Storage System

35
 Summary
• Exergy: Work potential of energy
 Exergy (work potential) associated with kinetic and potential energy
• Reversible work and irreversibility
• Second-law efficiency
• Exergy change of a system
 Exergy of a fixed mass: Nonflow (or closed system) exergy
 Exergy of a flow stream: Flow (or stream) exergy
• Exergy transfer by heat, work, and mass
• The decrease of exergy principle and exergy destruction
• Exergy balance: Closed systems
• Exergy balance: Control volumes
 Exergy balance for steady-flow systems
 Reversible work
 Second-law efficiency of steady-flow devices

36