244053522.xls.

ms_office 文档密级

RNC
V200R009

BTS3900-BTS3900A-DBS3900 WCDMA
V200R011C00SPC110 Parameter Reference

Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. For any assistance, please c
headquarters.

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: http://www.huawei.com
Email: [email protected]

Copyright © Huawei Technologies Co., Ltd. 2009. All rights reserved.

No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Te

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.

Notice
The information in this document is subject to change without notice. Every effort has been made in the preparation of this documen

9/12/2014 华为机密，未经许可不得扩散 第1页，共862页

 244053522.xls.ms_office 文档密级

CDMA
Reference

pport and service. For any assistance, please contact our local office or company

ans without prior written consent of Huawei Technologies Co., Ltd.

f their respective holders.

s been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this docume

9/12/2014 华为机密，未经许可不得扩散 第2页，共862页

 244053522.xls.ms_office 文档密级

ation, and recommendations in this document do not constitute the warranty of any kind, express or implied.

9/12/2014 华为机密，未经许可不得扩散 第3页，共862页

 244053522.xls.ms_office 文档密级

Purpose

This describes NodeB parameters, including the meaning, values, and usage of NodeB parameters.

Version

The product version related to this document is: V200R011C00SPC110

Intended Audience

•Network planners
•Field engineers
•System engineers
•Shift operators

Organization

Each parameter is described in the following aspects.

Description
Parameter ID
Parameter Name
NE

MML Command

Description

Value Type

GUI Value Range

Actual Value Range

Unit
Default Value
Recommended Value

Impact

Parameter Relationship

Access

9/12/2014 华为机密，未经许可不得扩散 第4页，共862页

 244053522.xls.ms_office 文档密级

Service Interrupted During Modification

Interruption Scope

Interruption Duration (Min)

Caution
Validation of Modification
Impact on Radio Network Performance
Introduced in Version
Attribute

9/12/2014 华为机密，未经许可不得扩散 第5页，共862页

 244053522.xls.ms_office 文档密级

ameters, including the meaning, values, and usage of NodeB parameters.

ed to this document is: V200R011C00SPC110

ed in the following aspects.

Remarks
A simple string for uniquely identifying a parameter
The full name of the parameter
Net Elements which the parameter is set
All the commands that use the parameter; optional/mandatory attribute of the
parameter in each command
The definition, function, and the reference protocol of the parameter

The data type of parameter value: integer, enumeration, and so on

The value range on the MML interface; the definition and the applied
situations for enumeration values
The actual value. For example, if the GUI value is 0, the actual value is OFF.

The unit of parameter value

The initial value specified by the system
Recommended values in different situations
The affected range upon modifying the value, such as RAB, IPPATH, CELL

The restriction and relation with other parameters, such as, the switches to
active the parameter and the value of related parameters
Whether this parameter is read/write,read only,or internal.

9/12/2014 华为机密，未经许可不得扩散 第6页，共862页

 244053522.xls.ms_office 文档密级

Modifying the parameters leads to service interruption?

The scope where the services are interrupted

The approximate duration of service interruption, in the unit of minute

Cautions to be taken during the modification

The way that you can take it effect.
Impact on Radio Network Performance
The version that the var appear firstly.
Whether this parameter is a radio parameter,a transport parameter,or an
equipment parameter.

9/12/2014 华为机密，未经许可不得扩散 第7页，共862页

 244053522.xls.ms_office 文档密级

9/12/2014 华为机密，未经许可不得扩散 第8页，共862页

Parameter ID Parameter Name NE MML Command

Resource limiting
128KRSCLMT NodeB SET RSCLMTPARA(Optional)
for 128Kbps GBR

Resource limiting
16KRSCLMT NodeB SET RSCLMTPARA(Optional)
for 16Kbps GBR

16QAMSW 16QAM Switch NodeB SET MACHSPARA(Optional)

Resource limiting
256KRSCLMT NodeB SET RSCLMTPARA(Optional)
for 256Kbps GBR

Resource limiting
32KRSCLMT NodeB SET RSCLMTPARA(Optional)
for 32Kbps GBR

Resource limiting
384KRSCLMT NodeB SET RSCLMTPARA(Optional)
for 384Kbps GBR

Resource limiting
64KRSCLMT NodeB SET RSCLMTPARA(Optional)
for 64Kbps GBR

Resource limiting
8KRSCLMT NodeB SET RSCLMTPARA(Optional)
for 8Kbps GBR

ARPPROXY ARP Proxy NodeB SET ETHPORT(Optional)

SET TMAGAIN(Mandatory)
ADD ALD(Optional)
SET TILTAER(Optional)
SET TMAGAIN(Optional)
Antenna Connector SET SASUDCLD(Optional)
ACN NodeB
No. SET SASUDCSW(Optional)
SET SASUGAIN(Optional)
SET SASUMODE(Optional)
SET TMAMODE(Optional)
SET ANTTILT(Optional)
ACVHL AC Upper Limit(V) NodeB SET ACDCVLIMIT(Optional)

ACVLL AC Lower Limit(V) NodeB SET ACDCVLIMIT(Optional)

BEAR Bear Type NodeB ADD OMCH(Mandatory)

BPT BootpTime(minute) NodeB SET BOOTPSWITCH(Optional)

Tilt Alarm Error

AER NodeB SET TILTAER(Mandatory)
Range(0.1 degree)

AGTHRESHO
AG Threshold NodeB SET MACEPARA(Optional)
LD
 SET ALMSHLD(Mandatory)
AID Alarm ID NodeB
ADD OBJALMSHLD(Mandatory)

Alarm ID Select
AIDST NodeB ADD OBJALMSHLD(Mandatory)
Type

ALMID Alarm ID NodeB SET ALMPORT

BRT Binding Route NodeB ADD OMCH(Optional)

Cabinet No. of
ANT1CN NodeB ADD SEC(Optional)
Antenna Channel1
 Antenna Channel1
ANT1N NodeB ADD SEC(Mandatory)
No.

Antenna No. of
ANT1N NodeB ADD LOCELL(Optional)
Power Amplifier1

Subrack No. of
ANT1SRN NodeB ADD SEC(Mandatory)
Antenna Channel1

Cabinet No. of
ANT2CN NodeB ADD SEC(Optional)
Antenna Channel2
 Antenna Channel2
ANT2N NodeB ADD SEC(Mandatory)
No.

Antenna No. of
ANT2N NodeB ADD LOCELL(Optional)
Power Amplifier2

Subrack No. of
ANT2SRN NodeB ADD SEC(Mandatory)
Antenna Channel2

Cabinet No. of
ANT3CN NodeB ADD SEC(Optional)
Antenna Channel3
 Antenna Channel3
ANT3N NodeB ADD SEC(Mandatory)
No.

Subrack No. of
ANT3SRN NodeB ADD SEC(Mandatory)
Antenna Channel3

Cabinet No. of
ANT4CN NodeB ADD SEC(Optional)
Antenna Channel4

Antenna Channel4
ANT4N NodeB ADD SEC(Mandatory)
No.
 Subrack No. of
ANT4SRN NodeB ADD SEC(Mandatory)
Antenna Channel4

ANTM Antenna Magnitude NodeB ADD SEC(Mandatory)

BT BER Threshold NodeB SET BERTHRESHOLD(Optional)

 ALD(Antenna Line
AST Device) System NodeB SET ALDPWRSW(Mandatory)
Type

AT Alarm Type NodeB SET NEMUDBAV(Mandatory)

ATMODE Auto Test Mode NodeB SET BATATPA(Mandatory)

Rx Attenuation
ATTEN NodeB SET RXATTEN(Mandatory)
Value(dB)

CCTM Timer_CC(ms) NodeB ADD SAALLNK(Optional)

 Authentication
AUTHMODE NodeB SET SSLAUTHMODE(Optional)
Mode

Auto Touchoff
AUTOSW NodeB SET EMGLICENSE(Optional)
Switch

SET
CLKM Clock Mode NodeB
E1T1WORKMODE(Optional)

AV Alarm Voltage NodeB SET NEMUDBAV(Mandatory)

AVOL Alarm Voltage NodeB SET ALMPORT

BAND1 Frequency Band NodeB SET ALDDEV(Mandatory)

BAND2 Frequency Band NodeB SET ALDDEV(Mandatory)

BAND3 Frequency Band NodeB SET ALDDEV(Mandatory)

BAND4 Frequency Band NodeB SET ALDDEV(Mandatory)

BAND5 Frequency Band NodeB SET ALDDEV(Mandatory)

BAND6 Frequency Band NodeB SET ALDDEV(Mandatory)

BASEID11 Base station ID NodeB SET ALDDEV(Mandatory)

BASEID20 Base station ID NodeB SET ALDDEV(Mandatory)

BC Battery Capacity NodeB ADD BATTERY(Optional)

Boost-Charging
BCD NodeB ADD BATTERY(Optional)
Duration

Battery Current
BCLC NodeB ADD BATTERY(Optional)
Limiting Coefficient

EM Environment Mode NodeB ADD BATTERY(Mandatory)

Temperature alarm
TUL NodeB ADD BATTERY(Optional)
Upper Limit
 Temperature alarm
TLL NodeB ADD BATTERY(Optional)
Lower Limit

Boost-charging
BCVOL NodeB SET BCFCVOLTAGE(Optional)
Voltage

BEAMWIDTH1
Beamwidth NodeB SET ALDDEV(Mandatory)
1

BEAMWIDTH1
Beamwidth NodeB SET ALDDEV(Mandatory)
2

BEAMWIDTH1
Beamwidth NodeB SET ALDDEV(Mandatory)
3

BEAMWIDTH2
Beamwidth NodeB SET ALDDEV(Mandatory)
1

BEAMWIDTH2
Beamwidth NodeB SET ALDDEV(Mandatory)
2
BEAMWIDTH2
Beamwidth NodeB SET ALDDEV(Mandatory)
3

BEAMWIDTH2
Beamwidth NodeB SET ALDDEV(Mandatory)
4

SET
DR Discard Rate NodeB HSDPAFLOWCTRLPARA(Optio
nal)

Destination IP
DSTIP NodeB ADD OMCH(Mandatory)
Address

Destination IP
DSTMASK NodeB ADD OMCH(Mandatory)
Mask

Excessive Burst
EBS NodeB SET LR(Mandatory)
Size(kbit)

BEARING Antenna Bearing NodeB SET ALDDEV(Mandatory)

Battery
BFLG Overtemperature NodeB SET HTPROTECT(Optional)
Shutdown Flag
BM Backup Mode NodeB ADD RRUCHAIN(Mandatory)

BN Sub Board No. NodeB STR E1T1RTTST(Optional)

ES Enable Switch NodeB SET CPSWITCH(Optional)

SET
BRKPOS1 Break Position1 NodeB
RRUCHAINBRKPOS(Mandatory)
 SET
BRKPOS2 Break Position2 NodeB
RRUCHAINBRKPOS(Optional)

SET
ES Enable Switch NodeB
DHCPRELAYSWITCH(Optional)

Battery Shutdown
BSDF NodeB SET SDPA(Optional)
Flag

Battery Shutdown
BSDV NodeB SET SDPA(Optional)
Voltage
 Frame Error Rate
FERAT AppearThreshold of NodeB SET ETHPORT(Optional)
FE MAC Layer

BT Board Type NodeB ADD BRD(Optional)

BT Board Type NodeB ACT SOFTWARE(Mandatory)

Battery Shutdown
BTEM NodeB SET HTPROTECT(Optional)
Temperature.

CARRIER Carrier No. NodeB SET RTWPINITADJ(Optional)

 ADD ALD(Optional)
CASE Scenario NodeB
SET ALDPWRSW(Optional)

Frame Error Rate

FERDT DisappearThreshol NodeB SET ETHPORT(Optional)
d of FE MAC Layer

Enable state of the

CCAEnableSta NodeB SET CERTFILE(Optional)
certificate chain

FLAG Flag NodeB ADD OMCH(Optional)

FPMUXSWITC
FPMUX Switch NodeB SET FPMUX(Optional)
H

Name of the
CertChain NodeB SET CERTFILE(Mandatory)
certificate chain file
 Condition for
CF NodeB ACT BATCHFILE(Optional)
Failure

CF Compress Flag NodeB SET CHRSW

CHANNEL Rx Channel No. NodeB SET RTWPINITADJ(Mandatory)

CHRSW CHR Switch NodeB SET CHRSW

CHRTYPE CHR Type NodeB SET CHRSW

CHT Change Time(S) NodeB STR RTWPRTTST(Mandatory)

CHTP Type Of Channel NodeB SET SASUGAIN(Mandatory)

Frame Max
FRAMELEN NodeB SET FPMUX(Optional)
Length(byte)

IDLE Timer_Idle(ms) NodeB ADD SAALLNK(Optional)

IFNO Interface Number NodeB ADD OMCH(Mandatory)

IFT Interface Type NodeB ADD OMCH(Mandatory)

Line
IMPEDANCE NodeB SET E1T1BEAR(Optional)
Impedance(ohm)
CLKSRC Clock Source Type NodeB SET CLKMODE(Optional)

CLS Sub Board Type NodeB STR E1T1RTTST(Mandatory)

 ADD AAL2PATH(Optional)
ADD ALD(Optional)
ADD BACKE1T1(Optional)
ADD BRD(Optional)
ADD CABINET(Mandatory)
ADD DEVIP(Optional)
ADD FRAATM(Optional)
ADD IMAGRP(Optional)
ADD IMALNK(Optional)
ADD IP2RSCGRP(Optional)
ADD IPCLKLNK(Optional)
ADD IPPATH(Optional)
ADD IPRT(Optional)
ADD LNKSRC(Optional)
ADD MPGRP(Optional)
ADD MPLNK(Optional)
ADD NPSU(Optional)
CN Cabinet No. NodeB
ADD OBJALMSHLD(Mandatory)
ADD OMCH(Optional)
ADD PPPLNK(Optional)
ADD RRU(Optional)
ADD RRUCHAIN(Optional)
ADD RSCGRP(Optional)
ADD SAALLNK(Optional)
ADD SCTPLNK(Optional)
ADD SUBRACK(Optional)
ADD TREELNKPVC(Optional)
ADD TSCROSS(Optional)
ADD UNILNK(Optional)
ADD CFMMA(Optional)
ADD CFMMEP(Optional)
ADD ETHTRK(Optional)
ADD ETHTRKLNK(Optional)
ADD BFDSESSION(Optional)

Cabinet No. of
CN1 NodeB ADD LOCELL(Optional)
Power Amplifier1

Cabinet No. of
CN2 NodeB ADD LOCELL(Optional)
Power Amplifier2
 ADD LOCELL(Optional)
Cabinet No. of RRU
CNB NodeB ADD SEC(Optional)
Begin
ADD TXPAIR(Optional)

ADD LOCELL(Optional)
Cabinet No. of RRU
CNE NodeB ADD SEC(Optional)
End
ADD TXPAIR(Optional)

Cabinet No. of DL
CNE1 NodeB ADD DLGROUP(Optional)
Process Unit 1

Cabinet No. of UL
CNE1 NodeB ADD ULGROUP(Optional)
Process Unit 1

Cabinet No. of DL
CNE2 NodeB ADD DLGROUP(Optional)
Process Unit 2

Cabinet No. of UL
CNE2 NodeB ADD ULGROUP(Optional)
Process Unit 2

Cabinet No. of DL
CNE3 NodeB ADD DLGROUP(Optional)
Process Unit 3

Cabinet No. of UL
CNE3 NodeB ADD ULGROUP(Optional)
Process Unit 3

Cabinet No. of DL
CNE4 NodeB ADD DLGROUP(Optional)
Process Unit 4

Cabinet No. of UL
CNE4 NodeB ADD ULGROUP(Optional)
Process Unit 4

CNOPINDEX CnOp Index NodeB SET EMGLICENSE(Mandatory)

CNOPNAME CnOp Name NodeB SET EMGLICENSE(Mandatory)

CONNTYPE Connection Type NodeB SET CONNTYPE(Optional)

COUNT Count NodeB SET EMGLICENSE(Optional)

COVERTYPE Cover Type NodeB ADD SEC(Mandatory)

IP IP Address NodeB SET LOCALIP(Mandatory)

IP Local IP Address NodeB ADD OMCH(Mandatory)

CQIFA CQI Filter Alpha NodeB SET MACHSPARA(Optional)

Name of the cancel

CRL NodeB SET CERTFILE(Mandatory)
list file

Enable state of the

CRLEnableSta NodeB SET CERTFILE(Optional)
certificate chain

SET PWRSYSCFG(Mandatory)
CS Config State NodeB SET CMUCFG(Mandatory)
SET NCMUCFG(Mandatory)

Cold Start Load

CSLSDF NodeB SET SDPA(Optional)
Shutdown Flag

Cold Start Load

CSLSDT Shutdown NodeB SET SDPA(Optional)
Temperature

CM Control enable
CTRLSW NodeB SET CMCTRLSW(Mandatory)
switch

CURRDA Current DA NodeB MOD CURRDA(Optional)

DA DA NodeB MOD CENTERDA(Optional)

DATE Installation Date NodeB MOD BATINDT(Optional)

DATE Date NodeB SET EMGLICENSE(Mandatory)

DAYS Days NodeB SET EMGLICENSE(Mandatory)

DBD Dead band NodeB SET HTCDPA(Optional)

DCID Destination Cell ID NodeB MOD CMBGROUP(Mandatory)

DCID1 Destination Cell ID1 NodeB ADD CMBGROUP(Mandatory)

DCID2 Destination Cell ID2 NodeB ADD CMBGROUP(Optional)

DCLOAD DC Load(20mA) NodeB SET SASUDCLD(Mandatory)

DCSWITCH DC Switch State NodeB SET SASUDCSW(Mandatory)

DCVHL DC Upper Limit NodeB SET ACDCVLIMIT(Optional)

DCVLL DC Lower Limit NodeB SET ACDCVLIMIT(Optional)

Delayed Discharge
DDSTM NodeB SET BATATPA(Optional)
Test Time(Day)

Default Power
DEFPWRLVL NodeB ADD LOCELL(Optional)
Level

Join Resource
JNRSCGRP NodeB ADD OMCH(Optional)
Group

Timer_Keep_Alive(
KATM NodeB ADD SAALLNK(Optional)
ms)
 SET TMAGAIN(Optional)
DEVTP Device Type NodeB
ADD ALD(Mandatory)

DEVTP Device Type NodeB SET SASUVSWRTHD(Optional)

SET TILTAER(Mandatory)
DEVTP Device Type NodeB SET TMAMODE(Optional)
SET ANTTILT(Mandatory)

AISG Protocl
DEVVER NodeB SET ALDDEV(Mandatory)
Version

Destination FACH
DFACHID NodeB MOD CMBGROUP(Mandatory)
Channel ID

Destination FACH
DFACHID1 NodeB ADD CMBGROUP(Mandatory)
Channel ID1

Destination FACH
DFACHID2 NodeB ADD CMBGROUP(Optional)
Channel ID2

SET
LOCIP Local IP Address NodeB
IPREMOTELOOP(Mandatory)
 Desensitization SET DESENS(Mandatory)
DI NodeB
Intensity ADD LOCELL(Optional)

DIVM Diversity Mode NodeB ADD SEC(Optional)

DLDELAY1 DL Time Delay1 NodeB ADD SEC(Optional)

DLDELAY2 DL Time Delay2 NodeB ADD SEC(Optional)

DLDELAY3 DL Time Delay3 NodeB ADD SEC(Optional)

DLDELAY4 DL Time Delay4 NodeB ADD SEC(Optional)

DL Frequency
DLFREQ NodeB ADD LOCELL(Mandatory)
Channel Number

DL BB Resource
DLGROUPN NodeB ADD DLGROUP(Mandatory)
Group No.

DL BB Resource
DLGROUPNO NodeB ADD LOCELL(Optional)
Group No.

LOCIP Local IP Address NodeB ADD SCTPLNK(Mandatory)

0.05C10 Discharge
DSCHGT0 NodeB SET BATCTPA(Optional)
Time

0.1C10 Discharge
DSCHGT1 NodeB SET BATCTPA(Optional)
Time
 0.2C10 Discharge
DSCHGT2 NodeB SET BATCTPA(Optional)
Time

0.3C10 Discharge
DSCHGT3 NodeB SET BATCTPA(Optional)
Time

0.4C10 Discharge
DSCHGT4 NodeB SET BATCTPA(Optional)
Time

0.5C10 Discharge
DSCHGT5 NodeB SET BATCTPA(Optional)
Time

0.6C10 Discharge
DSCHGT6 NodeB SET BATCTPA(Optional)
Time

0.7C10 Discharge
DSCHGT7 NodeB SET BATCTPA(Optional)
Time

0.8C10 Discharge
DSCHGT8 NodeB SET BATCTPA(Optional)
Time

0.9C10 Discharge
DSCHGT9 NodeB SET BATCTPA(Optional)
Time

MASK IP Address Mask NodeB SET LOCALIP(Mandatory)

Daylight saving
DST NodeB SET TZ(Optional)
time flag

DSTF Destination File NodeB SET CHRSW

MASK Local IP Mask NodeB ADD OMCH(Mandatory)

Max Connection
MAXCC NodeB ADD SAALLNK(Optional)
Control Count

MAXLE Max STAT Count NodeB ADD SAALLNK(Optional)

Max Poll Data

MAXPD NodeB ADD SAALLNK(Optional)
Count

Discharge Test
DSTML NodeB SET BATCTPA(Optional)
Time Limit

Destination Port
DSTPN NodeB ADD TREELNKPVC(Optional)
No.
 Destination Fraatm
DSTPN NodeB ADD TREELNKPVC(Optional)
Link No.

Destination Port
DSTPN NodeB ADD TSCROSS(Mandatory)
No.

Destination Port
DSTPT NodeB ADD TREELNKPVC(Mandatory)
Type

MCR Min Cell Rate NodeB ADD OMCH(Mandatory)

Destination
DSTSBT NodeB ADD TREELNKPVC(Mandatory)
Subboard Type

Destination
DSTSBT NodeB ADD TSCROSS(Mandatory)
Subboard Type

ADD TREELNKPVC(Mandatory)
DSTSN Destination Slot No. NodeB
ADD BACKE1T1(Mandatory)
DSTSN Destination Slot No. NodeB ADD TSCROSS(Mandatory)

Destination
DSTSRN NodeB ADD TREELNKPVC(Mandatory)
Subrack No.

MODE Bearing Mode NodeB SET E1T1BEAR(Optional)

NEXTHOP Next Hop IP NodeB ADD OMCH(Mandatory)

Timer_No_Respon
NRTM NodeB ADD SAALLNK(Optional)
se(ms)

OMPRI OM Priority NodeB SET DIFPRI(Optional)

Dynamic Code
DYNCODESW NodeB SET MACHSPARA(Optional)
Switch
EAGCHPCMO E-AGCH HPC
NodeB SET MACEPARA(Mandatory)
D Mode

EAGCHPCPA E-AGCH HPC

NodeB SET MACEPARA(Optional)
RA Parameters

EAGCHPOWE
E-AGCH Power NodeB SET MACEPARA(Mandatory)
R

EAGCHPWRO E-AGCH Power

NodeB SET MACEPARA(Mandatory)
FFSET Offset

PCR Peak Cell Rate NodeB ADD OMCH(Mandatory)

ED End Date NodeB STR E1T1RTTST(Mandatory)

EDAY End date NodeB SET TZ(Mandatory)

Battery Charge
EFF NodeB SET BATCTPA(Optional)
Efficiency

EFFECT Effect Signal NodeB SET LCPSW(Mandatory)

EM End date mode. NodeB SET TZ(Mandatory)

EMONTH End month NodeB SET TZ(Mandatory)

 Transport
ENCRYMODE NodeB SET FTPSCLT(Optional)
Encrypted Mode

ENDV End Voltage NodeB SET BATCTPA(Optional)

PEERIP Peer IP Address NodeB ADD OMCH(Mandatory)

PEERMASK Peer IP Mask NodeB ADD OMCH(Mandatory)

ET End time NodeB SET TZ(Mandatory)

ET End Time NodeB STR E1T1RTTST(Mandatory)

EWEEK End week NodeB SET TZ(Mandatory)

End week
EWSEQ NodeB SET TZ(Mandatory)
sequence

Float-charging
FCVOL NodeB SET BCFCVOLTAGE(Optional)
Voltage

PEERUDPPO SET
Peer UDP Port NodeB
RT IPREMOTELOOP(Mandatory)

PLR Appear
PLRAT NodeB SET PLRTHRESHOLD(Optional)
Threshold
 PLR Disappear
PLRDT NodeB SET PLRTHRESHOLD(Optional)
Threshold

POLL Timer_Poll(ms) NodeB ADD SAALLNK(Optional)

FLAG Enable Flag NodeB SET CFGFILEENB(Mandatory)

FLG NMPT Backup Flag NodeB SET MPTBKP(Mandatory)

FLR RRU Floor NodeB ADD RRU(Optional)

PREF Route Preference NodeB ADD OMCH(Optional)

PRIRULE Priority Rule NodeB SET DIFPRI(Optional)

RSCGRPID Resource Group ID NodeB ADD OMCH(Mandatory)

RT Route Type NodeB ADD OMCH(Optional)

Rx
RXBW NodeB ADD RSCGRP(Mandatory)
Bandwidth(kbps)

SCR Sustain Cell Rate NodeB ADD OMCH(Mandatory)

SCR Sustain Cell Rate NodeB ADD SAALLNK(Mandatory)

SIGPRI Signal Priority NodeB SET DIFPRI(Optional)

Bearing Service
ST NodeB ADD OMCH(Mandatory)
Type

SET TMAGAIN(Mandatory)
GAIN TMA Gain(0.25dB) NodeB
SET SASUGAIN(Mandatory)

GAIN1 Antenna Gain NodeB SET ALDDEV(Mandatory)

GAIN2 Antenna Gain NodeB SET ALDDEV(Mandatory)

GAIN3 Antenna Gain NodeB SET ALDDEV(Mandatory)

GAIN4 Antenna Gain NodeB SET ALDDEV(Mandatory)

GPSCD GPS Cable Delay NodeB SET GPSDELAY(Mandatory)

HCN Head Cabinet No. NodeB ADD RRUCHAIN(Optional)

TTW Two Tx Way NodeB ADD LOCELL(Optional)

High Speed
HISPM NodeB ADD LOCELL(Optional)
Movement Mode

Humidity Lower
HLL NodeB MOD NEMUTHLIMIT(Optional)
Limit

Local Cell Inner

HORAD NodeB ADD LOCELL(Optional)
Handover Radius

HPN Head Port No. NodeB ADD RRUCHAIN(Mandatory)

Head Interface
HSN NodeB ADD RRUCHAIN(Mandatory)
Board Slot No.

HSRN Head Subrack No. NodeB ADD RRUCHAIN(Optional)

 High Temperature
HTCP NodeB SET HTCDPA(Optional)
critical point

Heater Close
HTCT NodeB SET HTPA(Optional)
Temperature
 High temperature
HTDO NodeB SET HTCDPA(Optional)
delta Tout

Heater Start
HTST NodeB SET HTPA(Optional)
Temperatue

Humidity Upper
HUL NodeB MOD NEMUTHLIMIT(Optional)
Limit

HZ RRU Horizontal NodeB ADD RRU(Optional)

 Bearing Service
ST NodeB ADD SAALLNK(Optional)
Type

SUBFRAMELE Sub Frame Max

NodeB SET FPMUX(Optional)
N Length(byte)

SET
SWITCH Hsdpa Switch NodeB HSDPAFLOWCTRLPARA(Optio
nal)
IFOFFSET IF Offset NodeB SET IFOFFSET(Mandatory)

SET
TD Time Delay(5ms) NodeB HSDPAFLOWCTRLPARA(Optio
nal)

TIMER Timer(ms) NodeB SET FPMUX(Optional)

TLFRSWITCH TLFR SWITCH NodeB SET TLFRSWITCH(Optional)

SET
TXCLK Tx Clock NodeB
STM1WORKMODE(Mandatory)
VCI Bearing VCI NodeB ADD OMCH(Mandatory)

INFNO Interface No. NodeB SET NEMUANLGIN(Mandatory)

VPI Bearing VPI NodeB ADD OMCH(Mandatory)

Committed Burst
CBS NodeB SET LR(Mandatory)
Size(kbit)

INSTALLDATE Installation Date NodeB SET ALDDEV(Mandatory)

INSTALLID Installer's ID NodeB SET ALDDEV(Mandatory)

Committed
ULCIR Information NodeB SET LR(Mandatory)
Ratekbps
 Committed
DLCIR Information NodeB SET LR(Mandatory)
Ratekbps

DUPLEX Duplex NodeB SET ETHPORT(Optional)

NTP Server IP
IP NodeB SET SNTPCLTPARA(Optional)
Address

IP FTP Server IP NodeB SET CHRSW

SET
FRAME Frame Structure NodeB
E1T1WORKMODE(Optional)

FUNCTION Function NodeB SET LR(Optional)

IPMODE IP Clock Mode NodeB SET CLKMODE(Optional)

INSTAG Insert VLAN Tag NodeB SET VLANCLASS(Optional)

LM Loopback Mode NodeB SET E1T1LOP(Optional)

LM Loopback Mode NodeB SET IPREMOTELOOP(Optional)

Load
LFLG Overtemperature NodeB SET HTPROTECT(Optional)
Shutdown Flag

SET
LIMIT Alarm Limit NodeB
VSWRALMPARAM(Mandatory)

LL Lower Limit(V) NodeB SET NEMUINVLIMIT(Optional)

Lower Alarm Occur

LL NodeB SET ALMPORT
Limit
LM Loopback Mode NodeB SET STM1LOP(Optional)

SET
LNCODE Line Code NodeB
E1T1WORKMODE(Optional)

SET
LNCODE Line Code NodeB
E1T1WORKMODE(Optional)

SET IPREMOTELOOP(Optional)
Loopback
LT NodeB SET E1T1LOP(Optional)
Time(minute)
SET STM1LOP(Optional)
 SET
PEERIP Peer IP Address NodeB
IPREMOTELOOP(Mandatory)

SCRAM Scramble Mode NodeB SET SCRAM(Optional)

SPEED Speed NodeB SET ETHPORT(Optional)

LN IP Clock Link No. NodeB SET CLKMODE(Optional)

User Data Service

SRVPRIO NodeB SET VLANCLASS(Mandatory)
Priority

TRAFFIC Traffic Type NodeB SET VLANCLASS(Mandatory)

VLANGROUP
VLAN Group No NodeB SET VLANCLASS(Optional)
NO
 BLK LOCELL(Optional)
ADD LOCELL(Mandatory)
SET RSCLMTPARA(Optional)
SET DESENS(Optional)
SET MACHSPARA(Optional)
SET MACEPARA(Optional)
LOCELL Local Cell ID NodeB LST LOCELL(Optional)
DSP LOCELL(Optional)
DSP LOCELLRES(Optional)
UBL LOCELL(Optional)
RMV LOCELL(Mandatory)
MOD
RRUOFLOCELL(Mandatory)

VLANID VLAN ID NodeB SET VLANCLASS(Optional)

VLANPRIO VLAN Priority NodeB SET VLANCLASS(Optional)

Maximum SET ETHPORT(Optional)

MTU NodeB
Transmission Unit ADD ETHTRK(Optional)

Minimum timer
LOWERLIMIT NodeB SET CLSPATIMER
value

Load Shutdown
LSDF NodeB SET SDPA(Optional)
Flag

Load Shutdown
LSDV NodeB SET SDPA(Optional)
Voltage(V)

Address & Control ADD MPLNK(Optional)

ACFC NodeB
Field Compress ADD PPPLNK(Optional)
 Low temperature
LTCP NodeB SET HTCDPA(Optional)
critical point

Load Shutdown
LTEM NodeB SET HTPROTECT(Optional)
Temperature.
 Low Temperature
LTH NodeB SET TATH(Optional)
Threshold

Manual Touchoff
MANUALSW NodeB SET EMGLICENSE(Optional)
Switch

ADDR ATM Address NodeB ADD AAL2NODE(Mandatory)

ADDR ATM Address NodeB ADD AAL2ADJNODE(Mandatory)

ADD AAL2PATH(Optional)
ANI Adjacent Node ID NodeB
ADD AAL2ADJNODE(Mandatory)

MAXAGCHPO E-AGCH Max

NodeB SET MACEPARA(Mandatory)
WER Power

ADD MPGRP(Mandatory)
AUTH Authentication NodeB
ADD PPPLNK(Mandatory)

Auto Switch to
AUTOSWITCH NodeB ADD SCTPLNK(Optional)
MasAddr

NCP/CCP Bearing
BEAR NodeB ADD IUBCP(Optional)
Type

Max RRU Output MOD

MAXRRUPWR NodeB
Power RRUOFLOCELL(Mandatory)

BEAR Bearing Type NodeB ADD IP2RSCGRP(Optional)

SET
HSDPAFLOWCTRLPARA(Optio
BEAR Bearing Type NodeB
nal)
ADD RSCGRP(Mandatory)

Cell Delay Variation ADD TREELNKPVC(Optional)

CDVT NodeB
Tolerance(0.1us) ADD AAL2PATH(Optional)
CIP Client IP Address NodeB ADD IPCLKLNK(Mandatory)

CLKM Tx Clock Mode NodeB ADD IMAGRP(Optional)

MINAGCHPO E-AGCH Min

NodeB SET MACEPARA(Mandatory)
WER Power

CPPN CCP Port No. NodeB ADD IUBCP(Optional)

MINUTE Minute NodeB SET EMGLICENSE(Optional)

Measurement
MLL NodeB SET NEMUANLGIN(Optional)
Lower Limit

NCP/CCP Port
CPPT NodeB ADD IUBCP(Optional)
Type

MODE SASU Mode NodeB SET SASUMODE(Mandatory)

MODE TMA Mode NodeB SET TMAMODE(Mandatory)

 System Clock
MODE NodeB SET CLKMODE(Optional)
Working Mode

MODE Work Mode NodeB SET ALMPORT

MODELNUM Antenna Model No. NodeB SET ALDDEV(Mandatory)

DELAY Diff Max Delay(ms) NodeB ADD IMAGRP(Optional)

ADD TSCROSS(Optional)
DESCRI Description NodeB
ADD TREELNKPVC(Optional)

DHCP Server IP
DHCPSVRIP NodeB ADD DHCPSVRIP(Mandatory)
Address

Differentiated
DSCP Services Code NodeB ADD IPPATH(Mandatory)
Point

Destination IP ADD IP2RSCGRP(Mandatory)

DSTIP NodeB
Address ADD IPRT(Mandatory)

Measurement
MUL NodeB SET NEMUANLGIN(Optional)
Upper Limit

Destination IP ADD IP2RSCGRP(Mandatory)

DSTMASK NodeB
Address Mask ADD IPRT(Mandatory)
MXPWR Max Output Power NodeB ADD LOCELL(Mandatory)

MXPWRPHUS MAX POWER PER

NodeB SET MACHSPARA(Optional)
R HS-USER

NAME Name NodeB SET NODEBNAME(Mandatory)

SET OUTPORT(Optional)
SET TMAGAIN(Mandatory)
SET TILTAER(Mandatory)
SET SASUDCLD(Mandatory)
NAME Name NodeB
SET SASUDCSW(Mandatory)
SET SASUGAIN(Mandatory)
SET SASUMODE(Mandatory)

NAME Device Name NodeB SET ANTTILT(Mandatory)

NAME Device Name NodeB ADD ALD(Mandatory)

NAME Device Name NodeB SET TMAMODE(Mandatory)

Destination
DSTRSCGRP NodeB ADD TREELNKPVC(Mandatory)
Resource Group ID

Destination E1/T1
DSTTSN NodeB ADD TSCROSS(Mandatory)
Time Slot No.

Destination Port
DSTVCI NodeB ADD TREELNKPVC(Mandatory)
VCI

Destination Port
DSTVPI NodeB ADD TREELNKPVC(Mandatory)
VPI

FLAG Flag NodeB ADD IUBCP(Optional)

FPMUXSWITC
FPMUX Switch NodeB ADD IPPATH(Optional)
H

FRAATM Fraatm Link No. NodeB ADD FRAATM(Optional)

E-HICH HPC Mode

NSEHICHPCM
for Non-service NodeB SET MACEPARA(Mandatory)
OD
Radio Links Set

E-HICH HPC
NSEHICHPCP Parameters for Non-
NodeB SET MACEPARA(Optional)
ARA service Radio Links
Set

E-HICH Power for

NSEHICHPO
Non-service Radio NodeB SET MACEPARA(Mandatory)
WER
Links Set

E-HICH Power
NSEHICHPW Offset for Non-
NodeB SET MACEPARA(Mandatory)
ROFFSET service Radio Links
Set
 E-RGCH HPC
NSERGCHPC
Mode for Non- NodeB SET MACEPARA(Mandatory)
MOD
service Radio Links

E-RGCH HPC
NSERGCHPC
Parameters for Non- NodeB SET MACEPARA(Optional)
PARA
service Radio Links

E-RGCH Power for

NSERGCHPO
Non-service Radio NodeB SET MACEPARA(Mandatory)
WER
Links

E-RGCH Power
NSERGCHPW
Offset for Non- NodeB SET MACEPARA(Mandatory)
ROFFSET
service Radio Links

Frame Max
FRAMELEN NodeB ADD IPPATH(Optional)
Length(byte)

FRAMODE Frame Mode NodeB SET FRAMEMODE(Optional)

 Normal temperature
NTDI NodeB SET HTCDPA(Optional)
delta Tint

Normal temperature
NTDO NodeB SET HTCDPA(Optional)
delta Tout

OBJAID Object Alarm ID NodeB ADD OBJALMSHLD(Mandatory)

OBJN Object No. NodeB ADD OBJALMSHLD(Mandatory)

OBJTP Object Type NodeB ADD OBJALMSHLD(Mandatory)

 Overcurrent Alarm
OCTHD Clear NodeB SET ALDPWRSW(Optional)
Threshold(mA)

FRMLEN Tx Frame Length NodeB ADD IMAGRP(Optional)

OOS On/Off Status NodeB SET OUTPORT(Mandatory)

Overcurrent Alarm
OOTHD Occur NodeB SET ALDPWRSW(Optional)
Threshold(mA)

OPESORT Operating Sort NodeB SET ALDDEV(Mandatory)

ALD Protocl
OPEVER NodeB SET ALDDEV(Mandatory)
Version

SET TILTAER(Optional)
SET TMAGAIN(Optional)
SET SASUDCLD(Optional)
SET SASUDCSW(Optional)
OPMODE Operating Mode NodeB SET SASUGAIN(Optional)
SET SASUMODE(Optional)
SET TMAMODE(Optional)
SET SASUVSWRTHD(Optional)
SET ANTTILT(Optional)
OPTYPE Operation Type NodeB MOD CMBGROUP(Mandatory)

Over Temperature
OTH NodeB SET TATH(Optional)
Threshold
IFNO Interface Number NodeB ADD IPRT(Optional)

IFT Interface Type NodeB ADD IPRT(Mandatory)

ADD IMAGRP(Optional)
IMAGRPN IMA Group No. NodeB
ADD IMALNK(Optional)

IMALNKN IMA Link No. NodeB ADD IMALNK(Optional)

INSTAG Insert VLAN Tag NodeB ADD VLANMAP(Optional)

IP IP Address NodeB ADD DEVIP(Mandatory)

IP Header ADD MPGRP(Optional)

IPHC NodeB
Compress ADD PPPLNK(Optional)

ADD MPGRP(Optional)
IPMASK Local IP Mask NodeB
ADD PPPLNK(Optional)

ADD AAL2PATH(Optional)
Join Resource ADD IPPATH(Optional)
JNRSCGRP NodeB
Group ADD SAALLNK(Optional)
ADD TREELNKPVC(Optional)

LN Link No. NodeB ADD IPCLKLNK(Optional)

LN SAAL Link No. NodeB ADD IUBCP(Optional)

LN SCTP Link No. NodeB ADD IUBCP(Optional)

ADD AAL2NODE(Optional)
LN SAAL Link No. NodeB
ADD AAL2ADJNODE(Optional)

ADD MPGRP(Optional)
LOCALIP Local IP Address NodeB
ADD PPPLNK(Optional)

PI RHUB Port ID NodeB ADD RRU(Mandatory)

Private Key
PKPEnableSta Password Enabled NodeB SET CERTFILE(Optional)
State

LOCPORT Local SCTP Port NodeB ADD SCTPLNK(Mandatory)

MASK IP Address Mask NodeB ADD DEVIP(Mandatory)

PN Port No. NodeB STR E1T1RTTST(Mandatory)

PN Port No. NodeB SET OUTPORT(Mandatory)

PN NPSU No. NodeB ADD NPSU(Mandatory)

PN Port No. NodeB SET ALMPORT

ADD LNKSRC(Optional)
ADD DEVIP(Optional)
ADD PPPLNK(Optional)
ADD FRAATM(Optional)
PN Port No. NodeB ADD IPPATH(Optional)
ADD MPLNK(Optional)
ADD OMCH(Optional)
ADD SAALLNK(Optional)
ADD BACKE1T1(Optional)
 SET E1T1LOP(Optional)
SET
E1T1WORKMODE(Optional)
SET ETHPORT(Optional)
PN Port No. NodeB SET
HSDPAFLOWCTRLPARA(Optio
nal)
SET LR(Optional)
SET SCRAM(Optional)

ADD AAL2PATH(Optional)
PN Bearing Port No. NodeB ADD IP2RSCGRP(Optional)
ADD RSCGRP(Optional)

ADD AAL2PATH(Optional)
Bearing Fraatm
PN NodeB ADD RSCGRP(Optional)
Link No.
ADD SAALLNK(Optional)

PN Fraatm Link No. NodeB ADD OMCH(Mandatory)

SET
HSDPAFLOWCTRLPARA(Optio
PN Fraatm Link No. NodeB
nal)
SET SCRAM(Optional)

ADD TREELNKPVC(Optional)
MBS Max Burst Size(cell) NodeB
ADD AAL2PATH(Optional)
 ADD
PORT Destination Port NodeB
FTPSCLTDPORT(Mandatory)

MCPPP Multi Class PPP NodeB ADD MPGRP(Optional)

MCR Min Cell Rate NodeB ADD SAALLNK(Mandatory)

ADD AAL2PATH(Mandatory)
MCR Min Cell Rate NodeB
ADD TREELNKPVC(Mandatory)

Min Number of
MINLNK NodeB ADD IMAGRP(Optional)
Links Activated

MLPPP Packets
MPDAAT Discard Alarm NodeB ADD MPGRP(Optional)
Appear Threshold

Private Key File

PrivKey NodeB SET CERTFILE(Optional)
Name

PS RRU Position NodeB ADD RRU(Mandatory)

 Power Supply Port
Of ALD(Antenna
PSP NodeB SET ALDPWRSW(Mandatory)
Line Device)
System

PST power type NodeB SET NBPWRTYPE(Mandatory)

PT Port Type NodeB SET ALMPORT

PTYPE Power Type NodeB SET PWRSYSCFG(Optional)

Certificate File
PubCert NodeB SET CERTFILE(Optional)
Name

MLPPP Packets
Discard Alarm
MPDADT NodeB ADD MPGRP(Optional)
Disappear
Threshold
 Private Key
PWD NodeB SET CERTFILE(Mandatory)
Password

PWD Password NodeB SET CHRSW

PWRMGN Power Margin NodeB SET MACHSPARA(Optional)

Power Setting
PWRMODE NodeB MOD RRUOFLOCELL(Optional)
Mode
 Power Supply
Switch Of
PWRSW NodeB SET ALDPWRSW(Mandatory)
ALD(Antenna Line
Device) System

RADIUS Local Cell Radius NodeB ADD LOCELL(Optional)

ADD RRU(Mandatory)
SET
RCN RRU Chain No. NodeB
RRUCHAINBRKPOS(Mandatory)
ADD RRUCHAIN(Optional)

ADD MPGRP(Optional)
MPGRPN ML PPP Group No. NodeB
ADD MPLNK(Optional)
REMOTECELL Index of remote cell ADD
NodeB
GRPINDEX group REMOTECELLGRP(Mandatory)

REMOTECELL Name of Remote ADD

NodeB
GRPNAME Cell Group REMOTECELLGRP(Mandatory)

Maximum Receive ADD MPLNK(Optional)

MRU NodeB
Unit(byte) ADD PPPLNK(Optional)

RETTP RET Type NodeB ADD ALD(Optional)

RFDS RF Desensitivity NodeB SET RFDESPARAM(Optional)

MOD ULGROUP(Mandatory)
RGOPTYPE Operation Type NodeB
MOD DLGROUP(Mandatory)

RM Rollback Mode NodeB ACT BATCHFILE(Mandatory)

Index of Remote
RMTCGRPID NodeB ADD LOCELL(Optional)
Cell Group

RMTCM Remote Cell Mode NodeB ADD LOCELL(Optional)

RN RRU Name NodeB ADD RRU(Optional)

ADD MPGRP(Optional)
MUXCP PPP MuxCP NodeB
ADD PPPLNK(Optional)

Root Certificate File

RootCert NodeB SET CERTFILE(Optional)
Name
RRUMODE RRU Mode NodeB ADD LOCELL(Optional)

RRU Work
RS NodeB ADD RRU(Mandatory)
Standard

Resource Allocate
RSCALLOCM NodeB SET MACHSPARA(Optional)
Method

Next Hop IP
NEXTHOP NodeB ADD IPRT(Mandatory)
Address

NEXTHOPIP Next Hop IP NodeB ADD VLANMAP(Mandatory)

Resource Limiting
RSCLMSW NodeB SET MACHSPARA(Optional)
Switch

RSTMODE Reset Mode NodeB SET CFGFILEENB(Mandatory)

NO Tscross No. NodeB ADD TSCROSS(Mandatory)

NO PVC No. NodeB ADD TREELNKPVC(Mandatory)

RT RRU Type NodeB ADD RRU(Mandatory)

NODEBIP NodeB IP Address NodeB ADD IPPATH(Mandatory)

RTWP Initial
RTWPINITADJ NodeB SET RTWPINITADJ(Mandatory)
Adjusting(0.1dB)

NT Node Type NodeB ADD AAL2NODE(Mandatory)

Resource Allocate
RULE NodeB SET RESALLOCRULE(Optional)
Rule

NT Node Type NodeB ADD AAL2PATH(Mandatory)

RXID Rx Index NodeB SET RXATTEN(Mandatory)

RxNo Rx Unit No. NodeB SET RXSW(Optional)

RXSW Rx Unit Switch. NodeB SET RXSW(Mandatory)

PATHCHK Path Check NodeB ADD IPPATH(Optional)

PATHID IP Path ID NodeB ADD IPPATH(Mandatory)

PATHID AAL2 Path ID NodeB ADD AAL2PATH(Mandatory)

PCR Peak Cell Rate NodeB ADD SAALLNK(Mandatory)

SBS Subboard Status NodeB SET SUBBRD(Mandatory)

SBT Subboard Type NodeB SET SUBBRD(Mandatory)

 ADD LNKSRC(Mandatory)
ADD DEVIP(Mandatory)
ADD PPPLNK(Mandatory)
ADD AAL2PATH(Mandatory)
ADD FRAATM(Mandatory)
ADD IMAGRP(Mandatory)
ADD IMALNK(Mandatory)
ADD IP2RSCGRP(Mandatory)
ADD IPPATH(Mandatory)
ADD IPRT(Mandatory)
SBT Subboard Type NodeB
ADD MPGRP(Mandatory)
ADD MPLNK(Mandatory)
ADD OMCH(Mandatory)
ADD RSCGRP(Mandatory)
ADD SAALLNK(Mandatory)
ADD UNILNK(Mandatory)
ADD CFMMEP(Mandatory)
ADD ETHTRK(Mandatory)
ADD ETHTRKLNK(Mandatory)
ADD BACKE1T1(Mandatory)

SET
E1T1WORKMODE(Mandatory)
SBT Subboard Type NodeB SET ETHPORT(Mandatory)
SET LR(Mandatory)
SET SCRAM(Mandatory)

SET
SBT Subboard Type NodeB HSDPAFLOWCTRLPARA(Mand
atory)
SCCHPWR HS-SCCH Power NodeB SET MACHSPARA(Mandatory)

SCHEDULEPA MAC-e Schedule

NodeB SET MACEPARA(Optional)
RA Para

SCID Source Cell ID NodeB ADD CMBGROUP(Mandatory)

ADD AAL2PATH(Mandatory)
PCR Peak Cell Rate NodeB
ADD TREELNKPVC(Mandatory)

ADD SCTPLNK(Mandatory)
PEERIP Peer IP Address NodeB ADD PPPLNK(Optional)
ADD MPGRP(Optional)

PEERPORT Peer SCTP Port NodeB ADD SCTPLNK(Mandatory)

Protocol Field ADD MPLNK(Optional)

PFC NodeB
Compress ADD PPPLNK(Optional)

ADD MPLNK(Optional)
PPPLNKN ML PPP Link No. NodeB
ADD PPPLNK(Optional)

PREF Route Preference NodeB ADD IPRT(Optional)

SD Start Date NodeB STR E1T1RTTST(Mandatory)

SDAY Start date NodeB SET TZ(Mandatory)

Simple Discharge
SDSEV NodeB SET BATCTPA(Optional)
End Voltage(V)

Simple Discharge
SDSTML NodeB SET BATCTPA(Optional)
Time LimitMinute

ADD MPGRP(Mandatory)
PWD Password NodeB
ADD PPPLNK(Mandatory)

ADD SEC(Mandatory)
SECN Sector No. NodeB ADD LOCELL(Mandatory) ADD
TXPAIR(Manaatory)

SET ANTTILT(Mandatory)
SECN Sector No. NodeB
SET TILTAER(Mandatory)

RCR Receive Cell Rate NodeB ADD AAL2PATH(Mandatory)

ADD SEC(Optional)
SECT Sector Type NodeB
ADD LOCELL(Mandatory)

Supported
SECTORID11 Frequency Band of NodeB SET ALDDEV(Mandatory)
800MHz
 Supported
SECTORID20 Frequency Band of NodeB SET ALDDEV(Mandatory)
800MHz

E-HICH HPC Mode

SEHICHPCMO
for Service Radio NodeB SET MACEPARA(Mandatory)
D
Links Set

E-HICH HPC
SEHICHPCPA Parameters for
NodeB SET MACEPARA(Optional)
RA Service Radio Links
Set

E-HICH Power for

SEHICHPOW
Service Radio Links NodeB SET MACEPARA(Mandatory)
ER
Set

E-HICH Power
SEHICHPWR
Offset for Service NodeB SET MACEPARA(Mandatory)
OFFSET
Radio Links Set

E-RGCH HPC
SERGCHPCM
Mode for Service NodeB SET MACEPARA(Mandatory)
OD
Radio Links Set
 E-RGCH HPC
SERGCHPCP Parameters for
NodeB SET MACEPARA(Optional)
ARA Service Radio Links
Set

E-RGCH Power for

SERGCHPOW
Service Radio Links NodeB SET MACEPARA(Mandatory)
ER
Set

E-RGCH Power
SERGCHPWR
Offset for Service NodeB SET MACEPARA(Mandatory)
OFFSET
Radio Links Set

SERIAL Serial No. NodeB ADD ALD(Optional)

SERIALNUM Antenna Serial No. NodeB SET ALDDEV(Mandatory)

FTP Server Ip ADD

SERVERIP NodeB
Address FTPSCLTDPORT(Mandatory)

Source FACH
SFACHID NodeB ADD CMBGROUP(Mandatory)
Channel ID
SHLDFLG Shield Flag NodeB SET ALMSHLD(Mandatory)

RESTARTTM ADD MPLNK(Optional)

RestartTimer(ms) NodeB
R ADD PPPLNK(Optional)

SINGLERLEHI E-HICH Power for

NodeB SET MACEPARA(Mandatory)
CHPOWER Single Radio Link

RNCIP RNC IP Address NodeB ADD IPPATH(Mandatory)

SM Start date mode NodeB SET TZ(Mandatory)

SM Scheduling Method NodeB SET MACHSPARA(Optional)

SMONTH Start month NodeB SET TZ(Mandatory)

SET RTWPINITADJ(Mandatory)
SET TXSW(Mandatory)
SET IFOFFSET(Mandatory)
SET RXATTEN(Mandatory)
SET RFDESPARAM(Mandatory)
SET
VSWRALMPARAM(Mandatory)
SET RXSW(Optional)
SN Slot No. NodeB
ADD OBJALMSHLD(Mandatory)
ADD RRU(Mandatory)
SET OUTPORT(Mandatory)
SET SUBBRD(Mandatory)
ADD BRD(Mandatory)
SET CLKMODE(Optional)
SET ALMPORT(Mandatory)
SET RXINTDETSW(Optional)
 ADD LNKSRC(Mandatory)
ADD DEVIP(Mandatory)
ADD PPPLNK(Mandatory)
ADD AAL2PATH(Mandatory)
ADD FRAATM(Mandatory)
ADD IMAGRP(Mandatory)
ADD IMALNK(Mandatory)
ADD IP2RSCGRP(Mandatory)
ADD IPCLKLNK(Mandatory)
ADD IPPATH(Mandatory)
ADD IPRT(Mandatory)
ADD MPGRP(Mandatory)
SN Slot No. NodeB
ADD MPLNK(Mandatory)
ADD OMCH(Mandatory)
ADD RSCGRP(Mandatory)
ADD SAALLNK(Mandatory)
ADD SCTPLNK(Mandatory)
ADD UNILNK(Mandatory)
ADD CFMMA(Mandatory)
ADD CFMMEP(Mandatory)
ADD BFDSESSION(Mandatory)
ADD ETHTRK(Mandatory)
ADD ETHTRKLNK(Mandatory)
ADD BACKE1T1(Mandatory)

SET E1T1BEAR(Mandatory)
SET E1T1LOP(Mandatory)
SET
E1T1WORKMODE(Mandatory)
SET ETHPORT(Mandatory)
SET
HSDPAFLOWCTRLPARA(Mand
atory)
SN Slot No. NodeB
SET
IPREMOTELOOP(Mandatory)
SET LR(Mandatory)
SET SCRAM(Mandatory)
SET
STM1WORKMODE(Mandatory)
SET STM1LOP(Mandatory)
SET SDHJ0J1J2(Mandatory)
 Slot No. of Power
SN1 NodeB ADD LOCELL(Optional)
Amplifier1

Slot No. of Power

SN2 NodeB ADD LOCELL(Optional)
Amplifier2

ADD SEC(Optional)
Slot No. of RRU
SNB NodeB ADD LOCELL(Optional)
Begin
ADD TXPAIR(Optional)
ADD SEC(Optional)
Slot No. of RRU
SNE NodeB ADD LOCELL(Optional)
End
ADD TXPAIR(Optional)

Slot No. of DL
SNE1 NodeB ADD DLGROUP(Mandatory)
Process Unit 1

Slot No. of UL
SNE1 NodeB ADD ULGROUP(Mandatory)
Process Unit 1

Slot No. of DL
SNE2 NodeB ADD DLGROUP(Optional)
Process Unit 2

Slot No. of UL
SNE2 NodeB ADD ULGROUP(Optional)
Process Unit 2

Slot No. of DL
SNE3 NodeB ADD DLGROUP(Optional)
Process Unit 3

Slot No. of UL
SNE3 NodeB ADD ULGROUP(Optional)
Process Unit 3

Slot No. of DL
SNE4 NodeB ADD DLGROUP(Optional)
Process Unit 4

Slot No. of UL
SNE4 NodeB ADD ULGROUP(Optional)
Process Unit 4

Sensor Output
SOLL NodeB SET NEMUANLGIN(Optional)
Lower Limit(V)
 Sensor Output
SOLL NodeB SET NEMUANLGIN(Optional)
Lower LimitA

Sensor Output
SOUL NodeB SET NEMUANLGIN(Optional)
Upper Limit(V)

Sensor Output
SOUL NodeB SET NEMUANLGIN(Optional)
Upper LimitA

Sync
SP NodeB SET SNTPCLTPARA(Optional)
Period(Minute)

ADD AAL2PATH(Optional)
ADD IP2RSCGRP(Optional)
RSCGRPID Resource Group ID NodeB ADD IPPATH(Optional)
ADD RSCGRP(Optional)
ADD SAALLNK(Optional)

SPR Speed Rate NodeB ADD LOCELL(Mandatory)

SPTSTATEFW Support State
NodeB SET FTPSCLT(Optional)
L Firewall

SRCPN Source Port No. NodeB ADD TREELNKPVC(Optional)

Source Fraatm Link

SRCPN NodeB ADD TREELNKPVC(Optional)
No.

SRCPN Source Port No. NodeB ADD TSCROSS(Mandatory)

SRCPT Source Port Type NodeB ADD TREELNKPVC(Mandatory)

RSW Expected Rx Switch NodeB SET SDHJ0J1J2(Optional)

Source Subboard ADD TREELNKPVC(Mandatory)

SRCSBT NodeB
Type ADD TSCROSS(Mandatory)

Source Subboard ADD TREELNKPVC(Mandatory)

SRCSBT NodeB
Type ADD TSCROSS(Mandatory)

SRCSN Source Slot No. NodeB ADD TREELNKPVC(Mandatory)

SRCSN Source Slot No. NodeB ADD TSCROSS(Mandatory)

Source Subrack
SRCSRN NodeB ADD TREELNKPVC(Mandatory)
No.

RTTYPE Route Type NodeB ADD IPRT(Mandatory)

 ADD AAL2PATH
ADD SAALLNK
RU Rate Unit NodeB ADD TREELNKPVC
ADD RSCGRP
ADD OMCH

Rx
RXBW NodeB ADD IPPATH(Mandatory)
Bandwidth(kbps)

E-HICH Power
SRLEHICHPW
Offset for Single NodeB SET MACEPARA(Mandatory)
ROFFSET
Radio Link

ADD SUBRACK(Mandatory)
SET
SASUVSWRTHD(Mandatory)
SET RTWPINITADJ(Mandatory)
SET TXSW(Mandatory)
SET IFOFFSET(Mandatory)
SET RXATTEN(Mandatory)
SET RFDESPARAM(Mandatory)
SET
VSWRALMPARAM(Mandatory)
SET RXSW(Mandatory)
SET HTPROTECT(Mandatory)
SET
BCFCVOLTAGE(Mandatory)
ADD OBJALMSHLD(Mandatory)
SET TMAGAIN(Mandatory)
ADD RRU(Mandatory)
SRN Subrack No. NodeB
SET ACDCVLIMIT(Mandatory)
SET BATATPA(Mandatory)
SET BATCTPA(Mandatory)
SET HTCDPA(Mandatory)
SET OUTPORT(Mandatory)
SET PWRSYSCFG(Mandatory)
SET TATH(Mandatory)
SET SUBBRD(Mandatory)
SET TILTAER(Mandatory)
SET SASUDCLD(Mandatory)
SET SASUDCSW(Mandatory)
SET SASUGAIN(Mandatory)
SET SASUMODE(Mandatory)
SET ANTTILT(Mandatory)
ADD NPSU(Mandatory)
SET HTPA(Mandatory)
SET SDPA(Mandatory)
 ADD LNKSRC(Mandatory)
ADD DEVIP(Mandatory)
ADD PPPLNK(Mandatory)
ADD AAL2PATH(Mandatory)
ADD FRAATM(Mandatory)
ADD IMAGRP(Mandatory)
ADD IMALNK(Mandatory)
ADD IP2RSCGRP(Mandatory)
ADD IPCLKLNK(Mandatory)
ADD IPPATH(Mandatory)
ADD IPRT(Mandatory)
ADD MPGRP(Mandatory)
SRN Subrack No. NodeB ADD MPLNK(Mandatory)
ADD OMCH(Mandatory)
ADD RSCGRP(Mandatory)
ADD SAALLNK(Mandatory)
ADD SCTPLNK(Mandatory)
ADD TSCROSS(Mandatory)
ADD UNILNK(Mandatory)
ADD CFMMA(Mandatory)
ADD CFMMEP(Mandatory)
ADD BFDSESSION(Mandatory)
ADD ETHTRK(Mandatory)
ADD ETHTRKLNK(Mandatory)
ADD BACKE1T1(Mandatory)

SET E1T1BEAR(Mandatory)
SET E1T1LOP(Mandatory)
SET
E1T1WORKMODE(Mandatory)
SET ETHPORT(Mandatory)
SET
HSDPAFLOWCTRLPARA(Mand
atory)
SRN Subrack No. NodeB
SET
IPREMOTELOOP(Mandatory)
SET LR(Mandatory)
SET SCRAM(Mandatory)
SET
STM1WORKMODE(Mandatory)
SET STM1LOP(Mandatory)
SET SDHJ0J1J2(Mandatory)
 Subrack No. of
SRN1 NodeB ADD LOCELL(Mandatory)
Power Amplifier1

Subrack No. of
SRN2 NodeB ADD LOCELL(Optional)
Power Amplifier2

ADD SEC(Mandatory)
Subrack No. of
SRNB NodeB ADD LOCELL(Mandatory)
RRU Begin
ADD TXPAIR(Mandatory)
ADD SEC(Mandatory)
Subrack No. of
SRNE NodeB ADD LOCELL(Mandatory)
RRU End
ADD TXPAIR(Mandatory)

Subrack No. of DL
SRNE1 NodeB ADD DLGROUP(Optional)
Process Unit 1

Subrack No. of UL
SRNE1 NodeB ADD ULGROUP(Optional)
Process Unit 1

Subrack No. of DL
SRNE2 NodeB ADD DLGROUP(Optional)
Process Unit 2

Subrack No. of UL
SRNE2 NodeB ADD ULGROUP(Optional)
Process Unit 2

Subrack No. of DL
SRNE3 NodeB ADD DLGROUP(Optional)
Process Unit 3

Subrack No. of UL
SRNE3 NodeB ADD ULGROUP(Optional)
Process Unit 3

Subrack No. of DL
SRNE4 NodeB ADD DLGROUP(Optional)
Process Unit 4

Subrack No. of UL
SRNE4 NodeB ADD ULGROUP(Optional)
Process Unit 4

SRT Subrack Type NodeB ADD SUBRACK(Optional)

RXT Expected Rx Type NodeB SET SDHJ0J1J2(Optional)

Expected Rx
RXV NodeB SET SDHJ0J1J2(Optional)
Information

Expected Rx
RXVER NodeB SET SDHJ0J1J2(Optional)
Procotol Version

SAALNO SAAL Link No. NodeB ADD SAALLNK(Optional)

SCR Sustain Cell Rate NodeB ADD TREELNKPVC(Optional)

ST Start time NodeB SET TZ(Mandatory)

ST Start Time NodeB STR E1T1RTTST(Mandatory)

SCR Sustain Cell Rate NodeB ADD AAL2PATH(Mandatory)

ADD SITE(Mandatory)
ADD SEC(Mandatory)
STN Site No. NodeB
ADD LOCELL(Mandatory) ADD
TXPAIR(Mandatory)

SET ANTTILT(Mandatory)
STN Site No. NodeB
SET TILTAER(Mandatory)

STNAME Site Name NodeB ADD SITE(Mandatory)

 ADD FRAATM(Optional)
SCRAM Scramble Mode NodeB ADD IMAGRP(Optional)
ADD UNILNK(Optional)

SCTPNO SCTP Link No. NodeB ADD SCTPLNK(Optional)

SUBUNIT Subunit No. NodeB ADD ALD(Mandatory)

Switch of Time
SW NodeB SET SNTPCLTPARA(Optional)
Sync

Second Local IP
SECLOCIP NodeB ADD SCTPLNK(Optional)
Address

SWEEK Start week NodeB SET TZ(Mandatory)

 Second Peer IP
SECPEERIP NodeB ADD SCTPLNK(Optional)
Address

SET
SWITCH Function Switch NodeB
VSWRALMPARAM(Mandatory)

Smooth Power
SET
SWITCH Change Function NodeB
SMTHPWRSWTCH(Mandatory)
Switch

Start week
SWSEQ NodeB SET TZ(Mandatory)
sequence

SIP Server IP Address NodeB ADD IPCLKLNK(Mandatory)

Temperature
TCC Compensation NodeB ADD BATTERY(Optional)
Coefficient

TCN Tail Cabinet No. NodeB ADD RRUCHAIN(Optional)

Source Resource
SRCRSCGRP NodeB ADD TREELNKPVC(Mandatory)
Group ID

Timely Discharge
TDSTM NodeB SET BATATPA(Optional)
Test Time
 Antenna Tilt(0.1
TILT NodeB SET ANTTILT(Mandatory)
degree)

Installed
TILT1 NodeB SET ALDDEV(Mandatory)
Mechanical Tilt

Installed
TILT2 NodeB SET ALDDEV(Mandatory)
Mechanical Tilt
 Source E1/T1 Time
SRCTSN NodeB ADD TSCROSS(Mandatory)
Slot No.

SRCVCI Source Port VCI NodeB ADD TREELNKPVC(Mandatory)

SRCVPI Source Port VPI NodeB ADD TREELNKPVC(Mandatory)

Temperature Alarm
TLL NodeB MOD NEMUTHLIMIT(Optional)
Lower Limit
TLT Tout Limit NodeB SET HTCDPA(Optional)

TM Time NodeB SET EMGLICENSE(Mandatory)

TO Time offset(Minute) NodeB SET TZ(Mandatory)

TP RRU Topo Position NodeB ADD RRU(Mandatory)

TPN Tail Port No. NodeB ADD RRUCHAIN(Mandatory)

ST Service Type NodeB ADD TREELNKPVC(Optional)

 Bearing Service
ST NodeB ADD AAL2PATH(Optional)
Type

SET
STM1N STM1 No. NodeB STM1WORKMODE(Optional)
SET STM1LOP(Optional)

Tail Interface Board

TSN NodeB ADD RRUCHAIN(Mandatory)
Slot No.

TSRN Tail Subrack No. NodeB ADD RRUCHAIN(Optional)

TT Topo Type NodeB ADD RRUCHAIN(Optional)

Temperature Alarm
TUL NodeB MOD NEMUTHLIMIT(Optional)
Upper Limit

SUBFRAMELE Sub Frame Max

NodeB ADD IPPATH(Optional)
N Length(byte)

SW Tx Switch NodeB SET SDHJ0J1J2(Optional)

TB Trace Byte NodeB SET SDHJ0J1J2(Optional)

TIMER Timer(ms) NodeB ADD IPPATH(Optional)

16th Timeslot ADD IMAGRP(Optional)

TS16 NodeB
Support ADD UNILNK(Optional)

TxNo Tx Unit No. NodeB SET TXSW(Mandatory)

TXSW Tx Unit Switch NodeB SET TXSW(Mandatory)

 ADD MPLNK(Mandatory)
E1/T1 Time Slot
TSN NodeB ADD PPPLNK(Mandatory)
No.
ADD FRAATM(Mandatory)

TX
TXBW NodeB ADD IPPATH(Mandatory)
Bandwidth(kbps)
TXBW Tx Bandwidth(kbps) NodeB ADD RSCGRP(Mandatory)

TYPE Sensor Type NodeB SET NEMUANLGIN(Optional)

Undercurrent Alarm
UCTHD Clear NodeB SET ALDPWRSW(Optional)
Threshold(mA)

UL Upper Limit NodeB SET NEMUINVLIMIT(Optional)

 Upper Alarm Occur
UL NodeB SET ALMPORT
Limit

ULDELAY1 UL Time Delay1 NodeB ADD SEC(Optional)

ULDELAY2 UL Time Delay2 NodeB ADD SEC(Optional)

ULDELAY3 UL Time Delay3 NodeB ADD SEC(Optional)

ULDELAY4 UL Time Delay4 NodeB ADD SEC(Optional)

 UL Frequency
ULFREQ NodeB ADD LOCELL(Mandatory)
Channel Number

UL BB Resource
ULGROUPN NodeB ADD ULGROUP(Mandatory)
Group No.

UL BB Resource
ULGROUPNO NodeB ADD LOCELL(Optional)
Group No.

TXCBS Tx CBS(bit) NodeB ADD IPPATH(Mandatory)

TXEBS Tx EBS(bit) NodeB ADD IPPATH(Mandatory)

Undercurrent Alarm
UOTHD Occur NodeB SET ALDPWRSW(Optional)
Threshold(mA)

Maximum timer
UPPERLIMIT NodeB SET CLSPATIMER
value

USR User Name NodeB SET CHRSW

TXT Tx Type NodeB SET SDHJ0J1J2(Optional)

TXV Tx Information NodeB SET SDHJ0J1J2(Optional)

VENDOR Vendor Code NodeB ADD ALD(Optional)

TXVER Tx Procotol Version NodeB SET SDHJ0J1J2(Optional)

ADD MPGRP(Mandatory)
UN User Name NodeB
ADD PPPLNK(Mandatory)

UNILNKN UNI Link No. NodeB ADD UNILNK(Optional)

ADD AAL2PATH(Mandatory)
VCI Bearing VCI NodeB
ADD SAALLNK(Mandatory)

IMA Protocol
VER NodeB ADD IMAGRP(Optional)
Version

VLANGROUP
VLAN Group No NodeB ADD VLANMAP(Optional)
NO

VLANID VLAN ID NodeB ADD VLANMAP(Optional)

VLANMODE VLAN Mode NodeB ADD VLANMAP(Mandatory)

VLANPRIO VLAN Priority NodeB ADD VLANMAP(Optional)

ADD AAL2PATH(Mandatory)
VPI Bearing VPI NodeB
ADD SAALLNK(Mandatory)

VST VP/VC Switch Type NodeB ADD TREELNKPVC(Mandatory)

VT RRU Vertical NodeB ADD RRU(Optional)

WM Work Mode NodeB MOD DEMMODE(Optional)

ZONET Time zone NodeB SET TZ(Optional)

SD Switch of Detecting NodeB SET RXINTDETSW(Optional)

CM Check mode NodeB SET RXINTDETSW(Optional)

IQDL IQ Data Length NodeB SET RXINTDETSW(Mandatory)

PSP Power Start Period NodeB SET RXINTDETSW(Mandatory)

Power Collecting
PCT NodeB SET RXINTDETSW(Optional)
Time

PD Period of Detecting NodeB SET RXINTDETSW(Mandatory)

THR Interfere threshold NodeB SET RXINTDETSW(Mandatory)

NMCA Unit No. NodeB SET RXINTDETSW(Optional)

INCA1 Carrier Index 1 NodeB SET RXINTDETSW(Optional)

INCH1 Unit Index 1 NodeB SET RXINTDETSW(Optional)

INCA2 Carrier Index 2 NodeB SET RXINTDETSW(Optional)

INCH2 Unit Index 2 NodeB SET RXINTDETSW(Optional)

INCA3 Carrier Index 3 NodeB SET RXINTDETSW(Optional)

INCH3 Unit Index 3 NodeB SET RXINTDETSW(Optional)

INCA4 Carrier Index 4 NodeB SET RXINTDETSW(Optional)

INCH4 Unit Index 4 NodeB SET RXINTDETSW(Optional)

INCA5 Carrier Index 5 NodeB SET RXINTDETSW(Optional)

INCH5 Unit Index 5 NodeB SET RXINTDETSW(Optional)

INCA6 Carrier Index 6 NodeB SET RXINTDETSW(Optional)

INCH6 Unit Index 6 NodeB SET RXINTDETSW(Optional)

INCA7 Carrier Index 7 NodeB SET RXINTDETSW(Optional)

INCH7 Unit Index 7 NodeB SET RXINTDETSW(Optional)

INCA8 Carrier Index 8 NodeB SET RXINTDETSW(Optional)

INCH8 Unit Index 8 NodeB SET RXINTDETSW(Optional)

ADD SAALLNK(Mandatory)
ADD AAL2PATH(Mandatory)
RU Rate Unit NodeB ADD TREELNKPVC(Mandatory)
ADD OMCH(Mandatory)
ADD RSCGRP(Mandatory)

ICPT Ipclk ProtocolType NodeB ADD IPCLKLNK(Optional)

DM Domain NodeB ADD IPCLKLNK(Optional)

ADD IUBCP(Optional)
BELONG Belong Flag NodeB
ADD AAL2NODE(Optional)

NAME MD name NodeB ADD CFMMD(Mandatory)

LEVEL MD level NodeB ADD CFMMD(Optional)

ADD CFMMA(Mandatory)
ADD CFMMEP(Mandatory)
MDNAME MD Name NodeB
ADD CFMRMEP(Mandatory)
ADD CFMBNDIP(Mandatory)
ADD CFMMA(Mandatory)
ADD CFMMEP(Mandatory)
MANAME MA Name NodeB
ADD CFMRMEP(Mandatory)
ADD CFMBNDIP(Mandatory)

VLANID VLAN ID NodeB ADD CFMMA(Mandatory)

MEPID MEP ID NodeB ADD CFMMEP(Mandatory)

RMEPID RMEP ID NodeB ADD CFMBNDIP(Mandatory)

MAC RMEP MAC Addr NodeB ADD CFMRMEP(Optional)

BNDIP RMEP IP Addr NodeB ADD CFMBNDIP(Mandatory)

PT Port Type NodeB ADD CFMMEP(Mandatory)

PN Port No. NodeB ADD CFMMEP(Optional)

BFDSN BFD Session No. NodeB ADD BFDSESSION(Mandatory

SRCIP Source IP Address NodeB ADD BFDSESSION(Mandatory

Destination IP
DESTIP NodeB ADD BFDSESSION(Mandatory
Address

HT Hop Type NodeB ADD BFDSESSION(Mandatory

MINTI Min Tx Interval NodeB ADD BFDSESSION(Optional)

MINRI Min Rx Interval NodeB ADD BFDSESSION(Optional)

DM Detect Mult NodeB ADD BFDSESSION(Optional)

ADD ETHTRK(Optional)
TN TrunkNo. NodeB
ADD ETHTRKLNK(Optional)

LACP Lacp Switch NodeB ADD ETHTRK(Optional)

ARPPROXY ArpProxy NodeB ADD ETHTRK(Optional)

Frame Error Rate

FERAT AppearThreshold of NodeB ADD ETHTRK(Optional)
FE MAC Layer

Frame Error Rate

FERDT DisappearThreshol NodeB ADD ETHTRK(Optional)
d of FE MAC Layer

ADD CFMMEP(Optional)
PN Port No. NodeB
ADD ETHTRKLNK(Optional)
 Maximum Efach
MAXEFACHH
Retransmission NodeB SET MACHSPARA(Optional)
ARQRT
Times

Max HARQ
Retransmission
MAXNONCON Times of Non-
NodeB SET MACHSPARA(Optional)
VERHARQRT Conversational
serive in Cell DCH
state

HS-SCCH Power
HSSCCHPWR
Control Method in NodeB SET MACHSPARA(Optional)
CMINDCH
CELL DCH state

EFACH HS-SCCH
HSSCCHPWR
Power Control NodeB SET MACHSPARA(Optional)
CMINEFACH
Method

HS-SCCH FER
HSSCCHFER
Target in CELL NodeB SET MACHSPARA(Optional)
TRGTINDCH
DCH State

CQI Adjust
CQIADJALGO Algorithm Switch of
NodeB SET MACHSPARA(Optional)
FCON Conversational
Service

CQI Adjust
CQIADJALGO Algorithm Switch of
NodeB SET MACHSPARA(Optional)
FNONCON non-Conversational
Service
RBLERTARGE Residual Bler
NodeB SET MACHSPARA(Optional)
T Target

HSUPA CE
HSUPACESC
SCHEDULING NodeB SET MACEPARA(Optional)
HSWITCH
SWITCH
HSUPA
HSUPAOLSC OVERLOAD
NodeB SET MACEPARA(Optional)
HSWITCH SCHEDULING
SWITCH

SLOCELL Source LocalCell ID NodeB ADD PAGRP(Mandatory)

Destination
DLOCELL NodeB ADD PAGRP(Mandatory)
LocalCell ID

Max Sharing Power

MAXSHRTO NodeB ADD PAGRP(Optional)
Ratio

Sharing Power
SHMGN NodeB ADD PAGRP(Optional)
Margin

SET
R99 Flow Control
SWITCH NodeB R99FLOWCTRLSWICH(Mandato
Function Switch
ry)

Dl BB Resource
DLRESMODE NodeB ADD LOCELL(Optional)
Allocation Mode

BB Resource Pool
BBPOOLTYPE NodeB ADD LOCELL(Optional)
Type

SET
Itel Shutdown
ISD NodeB ITELSHUTDOWN(Mandatory)
Switch

SD Switch of Detecting NodeB SET RXINTDETSW(Optional)

CM Check mode NodeB SET RXINTDETSW(Optional)

IQDL IQ Data Length NodeB SET RXINTDETSW(Mandatory)

PSP Power Start Period NodeB SET RXINTDETSW(Mandatory)

Power Collecting
PCT NodeB SET RXINTDETSW(Optional)
Time

PD Period of Detecting NodeB SET RXINTDETSW(Mandatory)

THR Interfere threshold NodeB SET RXINTDETSW(Mandatory)

NMCA Unit No. NodeB SET RXINTDETSW(Optional)

INCA1 Carrier Index 1 NodeB SET RXINTDETSW(Optional)

INCH1 Unit Index 1 NodeB SET RXINTDETSW(Optional)

INCA2 Carrier Index 2 NodeB SET RXINTDETSW(Optional)

INCH2 Unit Index 2 NodeB SET RXINTDETSW(Optional)

INCA3 Carrier Index 3 NodeB SET RXINTDETSW(Optional)

INCH3 Unit Index 3 NodeB SET RXINTDETSW(Optional)

INCA4 Carrier Index 4 NodeB SET RXINTDETSW(Optional)

INCH4 Unit Index 4 NodeB SET RXINTDETSW(Optional)

INCA5 Carrier Index 5 NodeB SET RXINTDETSW(Optional)

INCH5 Unit Index 5 NodeB SET RXINTDETSW(Optional)

INCA6 Carrier Index 6 NodeB SET RXINTDETSW(Optional)

INCH6 Unit Index 6 NodeB SET RXINTDETSW(Optional)

INCA7 Carrier Index 7 NodeB SET RXINTDETSW(Optional)

INCH7 Unit Index 7 NodeB SET RXINTDETSW(Optional)

INCA8 Carrier Index 8 NodeB SET RXINTDETSW(Optional)

INCH8 Unit Index 8 NodeB SET RXINTDETSW(Optional)

PT Bearing Port Type NodeB ADD AAL2PATH(Optional)

ADD DEVIP(Optional)ADD
PT Port Type NodeB
IPPATH(Optional)
PT Bearing Port Type NodeB ADD IP2RSCGRP(Optional)

PT Port Type NodeB ADD LNKSRC(Optional)

PT Port Type NodeB ADD OMCH(Optional)

PT Bearing Port Type NodeB ADD RSCGRP(Optional)

 IMA Group
IMAGRPSBT NodeB ADD IMALNK(Optional)
Subboard Type

IP Packets Discard
ADD MPGRP(Optional)ADD
IPDAAT Alarm Appear NodeB
PPPLNK(Optional)
Threshold

IP Packets Discard
ADD MPGRP(Optional)ADD
IPDAAT Alarm Disappear NodeB
PPPLNK(Optional)
Threshold

ML PPP Group
MPGRPSBT NodeB ADD MPLNK(Optional)
Subboard Type

E1T1SRN E1T1 Subrack No. NodeB ADD MPLNK(Mandatory)

E1T1SN E1T1 Slot No. NodeB ADD MPLNK(Mandatory)

E1T1 Subboard
E1T1SBT NodeB ADD MPLNK(Mandatory)
Type

E1T1PN E1T1 Port No. NodeB ADD MPLNK(Mandatory)

HWNO Back Board Hw No. NodeB ADD MPLNK(Mandatory)

FCS Frame CRC NodeB ADD MPLNK(Mandatory)

RMEPID RMEP ID NodeB ADD CFMRMEP(Mandatory)

SET
STM1WORKMODE(Mandatory)
SBT Subboard Type NodeB
SET STM1LOP(Mandatory)
SET SDHJ0J1J2(Mandatory)
 SET
OAM3AHSW 3ah Switch NodeB STM1WORKMODE(Mandatory)
SET STM1LOP(Mandatory)

PTPPRI PTP Priority NodeB SET DIFPRI(Mandatory)

CLEAR Clear Statistic NodeB DSP CFMMEP(Mandatory)

No. of Send STR

CNT NodeB
Packets CFMLOOPBACKTST(Mandatory)

STR
SZ Packet Size(bytes) NodeB
CFMLOOPBACKTST(Mandatory)

STR
TMOUT Timeout(s) NodeB
CFMLOOPBACKTST(Mandatory)

STR
INTVL Interval(s) NodeB
CFMLOOPBACKTST(Mandatory)

PT Port Type NodeB SET LR(Mandatory)

PTYPE The type of power NodeB ADD BATTERY(Mantory)

Description Value Type GUI Value Range Actual Value Range Unit

Upper limit ratio of the power for

the user with 128 kbps GBR to the Interval Type 1~100 1~100 %
total power of the cell

Upper limit ratio of the power for

the user with 16 kbps GBR to the Interval Type 1~100 1~100 %
total power of the cell

Enumeration
16QAM Switch OPEN, CLOSE OPEN, CLOSE None
Type

Upper limit ratio of the power for

the user with 256 kbps GBR to the Interval Type 1~100 1~100 %
total power of the cell

Upper limit ratio of the power for

the user with 32 kbps GBR to the Interval Type 1~100 1~100 %
total power of the cell

Upper limit ratio of the power for

the user with 384 kbps GBR to the Interval Type 1~100 1~100 %
total power of the cell

Upper limit ratio of the power for

the user with 64 kbps GBR to the Interval Type 1~100 1~100 %
total power of the cell

Upper limit ratio of the power for

the user with 8 kbps GBR to the Interval Type 1~100 1~100 %
total power of the cell

DISABLE(Disable
Enumeration Arp Proxy),
ARP Proxy DISABLE, ENABLE None
Type ENABLE(Enable
Arp Proxy)

N0A, N0B, N1A, N0A, N0B, N1A,

Enumeration N1B, N2A, N2B, N1B, N2A, N2B,
Antenna Connector Number None
Type N3A, N3B, N4A, N3A, N3B, N4A,
N4B, N5A, N5B N4B, N5A, N5B
AC Upper Limit of the NPMU
Interval Type 60~300 60~300 V
AC/DC Voltage Alarm Threshold

AC Lower Limit of the NPMU

Interval Type 60~300 60~300 V
AC/DC Voltage Alarm Threshold

Bearing Type, which indicates

whether the Resource Group Enumeration
ATM, IPV4 ATM, IPV4 None
Bearing Type is configured on the Type
IP link or the ATM link.

BootpTime. The Bootp Time starts

Interval Type 15~70000000 15~70000000 min
when the OMCH is abnormal.

degre
Tilt Alarm Error Range Interval Type 0~10 0.1~1, Step:0.1
e

AG Threshold. If the UE-expected

authorized value is equal to or
great than the active authorized
value plus this threshold value,
Interval Type 0~31 0~31 None
authorize the UE through the AG
channel. Otherwise, authorize the
UE through RG channel; It may
affect the rate of HSUPA.
Alarm ID Interval Type 1~32000 1~32000 None

ALL(All of alarm
ALL(All of alarm ID),
Enumeration ID),
Alarm ID Select Type ONEBYONE(One by None
Type ONEBYONE(One
one alarm ID)
by one alarm ID)

Alarm ID Interval Type 65334~65535 65334~65537 None

Binding Route. When the remote

maintenance IP address and local
NO(not bind a
maintenance IP address are in Enumeration
route), YES(bind a NO, YES None
different network segments, the Type
route)
binding route should be set. It
indicates whether to bind a route.
Cabinet No. of Antenna Channel1:
There are one or more antenna
channels in one sector. The
number of the channels equals
Enumeration MASTER(Master
antenna magnitude. The antenna MASTER None
Type cabinet)
channels are identified by antenna
connectors at the cabinet top,
hereinafter referred to as "antenna
connector".
It is the No. of the first antenna
connector; There are one or more
antenna channels in one sector.
R0A(Cabinet
The number of the channels equals
Enumeration No.0A Ant),
antenna magnitude. The antenna R0A, R0B None
Type R0B(Cabinet
channels are identified by antenna
No.0B Ant)
connectors at the cabinet top,
hereinafter referred to as "antenna
connector".

ANTA(No.A Ant of
It is the Antenna No. of the first Enumeration Power Amplifier),
ANTA, ANTB None
antenna connector; Type ANTB(No.B Ant of
Power Amplifier)

Subrack No. of Antenna Channel1:

There are one or more antenna
channels in one sector. The
number of the channels equals
antenna magnitude. The antenna Interval Type 20~254 20~254 None
channels are identified by antenna
connectors at the cabinet top,
hereinafter referred to as "antenna
connector".

Cabinet No. of Antenna Channel2:

There are one or more antenna
channels in one sector. The
number of the channels equals
Enumeration MASTER(Master
antenna magnitude. The antenna MASTER None
Type cabinet)
channels are identified by antenna
connectors at the cabinet top,
hereinafter referred to as "antenna
connector".
It is the No. of the second antenna
connector; There are one or more
antenna channels in one sector.
R0A(Cabinet
The number of the channels equals
Enumeration No.0A Ant),
antenna magnitude. The antenna R0A, R0B None
Type R0B(Cabinet
channels are identified by antenna
No.0B Ant)
connectors at the cabinet top,
hereinafter referred to as "antenna
connector".

ANTA(No.A Ant of
It is the Antenna No. of the second Enumeration Power Amplifier),
ANTA, ANTB None
antenna connector; Type ANTB(No.B Ant of
Power Amplifier)

Subrack No. of Antenna Channel2:

There are one or more antenna
channels in one sector. The
number of the channels equals
antenna magnitude. The antenna Interval Type 20~254 20~254 None
channels are identified by antenna
connectors at the cabinet top,
hereinafter referred to as "antenna
connector".

Cabinet No. of Antenna Channel3:

There are one or more antenna
channels in one sector. The
number of the channels equals
Enumeration MASTER(Master
antenna magnitude. The antenna MASTER None
Type cabinet)
channels are identified by antenna
connectors at the cabinet top,
hereinafter referred to as "antenna
connector".
It is the No. of the third antenna
connector; There are one or more
antenna channels in one sector.
R0A(Cabinet
The number of the channels equals
Enumeration No.0A Ant),
antenna magnitude. The antenna R0A, R0B None
Type R0B(Cabinet
channels are identified by antenna
No.0B Ant)
connectors at the cabinet top,
hereinafter referred to as "antenna
connector".

Subrack No. of Antenna Channel3:

There are one or more antenna
channels in one sector. The
number of the channels equals
antenna magnitude. The antenna Interval Type 20~254 20~254 None
channels are identified by antenna
connectors at the cabinet top,
hereinafter referred to as "antenna
connector".

Cabinet No. of Antenna Channel4:

There are one or more antenna
channels in one sector. The
number of the channels equals
Enumeration MASTER(Master
antenna magnitude. The antenna MASTER None
Type cabinet)
channels are identified by antenna
connectors at the cabinet top,
hereinafter referred to as "antenna
connector".

It is the No. of the fourth antenna

connector; There are one or more
antenna channels in one sector.
R0A(Cabinet
The number of the channels equals
Enumeration No.0A Ant),
antenna magnitude. The antenna R0A, R0B None
Type R0B(Cabinet
channels are identified by antenna
No.0B Ant)
connectors at the cabinet top,
hereinafter referred to as "antenna
connector".
Subrack No. of Antenna Channel4:
There are one or more antenna
channels in one sector. The
number of the channels equals
antenna magnitude. The antenna Interval Type 20~254 20~254 None
channels are identified by antenna
connectors at the cabinet top,
hereinafter referred to as "antenna
connector".

It refers to the magnitude of

1(single antenna),
antennas in the sector. Do not use Enumeration
2(two antennas), 1, 2, 4 None
it when Sector Type is Distributed Type
4(four antennas)
Sector.

1E-3(E1/T1 high bit

error rate threshold
1E-3), 1E-4(E1/T1
high bit error rate
Enumeration threshold 1E-4), 1E-3, 1E-4, 1E-5,
BER Threshold None
Type 1E-5(E1/T1 high bit 1E-6
error rate threshold
1E-5), 1E-6(E1/T1
high bit error rate
threshold 1E-6)
 TMA12DB_ONLY_
NON_AISG (Only
TMA 12dB
(NON_AISG)),
TMA24DB_ONLY_
NON_AISG (Only
TMA 24dB
(NON_AISG)),
RET_ONLY_COAX TMA12DB_ONLY_N
IAL (Only RET ON_AISG
(COAXIAL)), TMA24DB_ONLY_N
Antenna Line Device (ALD) Enumeration RET_ONLY_MULT ON_AISG
None
System Type Type ICORE (Only RET RET_ONLY_COAXI
(MULTICORE)), AL TMA12DB_AISG
TMA12DB_AISG TMA24DB_AISG
(12dB TMA and CUSTOM
RET or Only TMA
12dB (AISG)),
TMA24DB_AISG
(24dB TMA and
RET or Only TMA
24dB (AISG)),
CUSTOM
(Custom)
WATER (water
immersion),
SMOKING WATER,
Enumeration (smoking), SMOKING,
Alarm Type Value None
Type INFRARED INFRARED,
(infrared), GATING
GATING (door
control)
PERIOD (Period
Auto Test),
POWERCUT
(Power Cut Auto
PERIOD,
Test),
Enumeration POWERCUT,
Battery Auto Test Mode PERIODPOWERC None
Type PERIODPOWERCU
UT (Period and
T, NOAUTOTEST
Power Cut Auto
Test),
NOAUTOTEST
(No Auto Test)

Value of the WRFU/RRU RX

Interval Type 0, 4~22 0, 4~22 dB
Attenuation

Timer_CC, which indicates the

length of the SSCOP timer
Interval Type 100~65535 100~65535 ms
Timer_CC specified in the SAAL-
related protocol.
 NONE (Verify
SSL Handshake Authentication Enumeration None), PEER
None, PEER None
Mode Type (Verify Peer
Certificate)

Enumeration
Auto Touchoff Switch ON, OFF ON, OFF None
Type

Clock Mode. If this parameter is

Enumeration MASTER(Master),
not specified, the original value is MASTER, SLAVE None
Type SLAVE(Slave)
kept.

NEMU Dedicated Boolean Alarm Enumeration HIGH (High), LOW

HIGH, LOW None
Voltage Type (Low)

HIGH (Alarms at
Enumeration high impedance),
Alarm Voltage HIGH, LOW None
Type LOW (Alarms at
low impedance)

Enumeration
Frequency Band No, Yes No, Yes None
Type

Enumeration
Frequency Band No, Yes No, Yes None
Type

Enumeration
Frequency Band No, Yes No, Yes None
Type
 Enumeration
Frequency Band No, Yes No, Yes None
Type

Enumeration
Frequency Band No, Yes No, Yes None
Type

Enumeration
Frequency Band No, Yes No, Yes None
Type

A string of up to 12
Base station ID String Type None None
bytes

A string of up to 32
Base station ID String Type None None
bytes

Battery Capacity Interval Type 5~600 5~600 Ah

Boost-Charging Duration Interval Type 30~240 30~240 day

Battery Current Limiting Coefficient Any Type 0.05~0.25 0.05~0.25 None

Enumeration
Environment Mode INNER, OUTER INNER, OUTER None
Type

Over-temperature alarm threshold Celsi

Interval Type 40~79 40~79
of battery temperature us
Under-temperature alarm threshold Celsi
Interval Type -19~5 -19~5
of battery temperature us

Boost-Charging Voltage of the 43.2~57.6, Precision:

Any Type 43.2~57.6 V
NPMU 0.01

Beamwidth Range Type 0~255 0~255 deg

Beamwidth Range Type 0~255 0~255 deg

Beamwidth Range Type 0~255 0~255 deg

Beamwidth Range Type 0~65535 0~65535 deg

Beamwidth Range Type 0~65535 0~65535 deg

Beamwidth Range Type 0~65535 0~65535 deg

Beamwidth Range Type 0~65535 0~65535 deg

Discard Rate. The link is not

congested when the frame loss
Interval Type 0~1000 0~1, Step: 0.001 None
ratio is lower than or equal to this
threshold.

Destination IP Address. This

parameter must meet all the
following conditions:
The IP address must be the one of
legal A, B, or C type, excluding
0.0.0.0~255.255.255.
the default route (IP address IP Address Type - None
255
0.0.0.0).
The IP & mask must be equal to
this IP address.
The mask in binary does not allow
"0" before "1", or "1" after "0".

Destination IP Mask. This

parameter must meet all the
following conditions:
0.0.0.0~255.255.255.
The IP & mask must be equal to IP Address Type - None
255
this IP address.
The mask in binary does not allow
"0" before "1", or "1" after "0".

Excessive Burst Size Interval Type 0~155000 0~155000 kbit

Antenna Bearing Range Type 0~65535 0~65535 None

Battery Overtemperature Shutdown Enumeration DISABLE(Disable),

ENABLE, DISABLE None
Flag Type ENABLE(Enable)
Link Backup Mode (For Ring Enumeration
COLD, HOT COLD, HOT None
Topology Only) Type

Number of the Sub-Board of the

Interval Type 0 0 None
E1/T1 Routine Test

Enumeration DISABLE(Disable),
Enable Switch DISABLE, ENABLE None
Type ENABLE(Enable)

First Break Point Position of the

Interval Type 0~8 0~8 None
RRU Chain/Ring
Second Break Point Position of the
RRU Chain/Ring (For Ring
Topology Only) If it is not specified, Interval Type 0~8 0~8 None
it equals to the value of the first
break point position.

Enumeration DISABLE(Disable),
Enable Switch DISABLE, ENABLE None
Type ENABLE(Enable)

Enumeration DISABLE(Disable),
Battery Shutdown Flag ENABLE, DISABLE None
Type ENABLE(Enable)

35.0~55.6,
Battery Shutdown Voltage Any Type 35.0~55.6 V
Precision: 0.01
Frame Error Rate AppearThreshold
Interval Type 0~100 0~0.1, Step: 0.001 None
of FE MAC Layer

NEMU (NE
Environment
Monitoring Unit),
NFAN (NodeB FAN
Box), WMPT
(WCDMA Main
Processing &
Transmission unit),
UTRP (Universal
extension
TRansmission
Processing unit),
WMPT, UTRP,
WBBPa (WCDMA
WBBPa, WBBPb,
Enumeration BaseBand Process
Added Board Type MRRU, RHUB, None
Type unit type A),
PRRU, SRXU,
WBBPb (WCDMA
WRFU
BaseBand Process
unit type B), UPEA
(Universal Power
and environment
Interface Unit A),
UPEB (Universal
Power and
environment
Interface Unit B),
UEIU (Universal
environment
Interface Unit).

HBBU/HBBUC, HBBU/HBBUC,
Enumeration
Activated Board Type MRRU, RHUB, MRRU, RHUB, None
Type
PRRU PRRU

degre
Battery Shutdown Temperature Interval Type 40~70 40~70
e

0~1(2 carrier
Number of the Carrier in the Initial 0~1(2 carrier RRU),
Interval Type RRU), 0~3(4 None
RTWP Adjusting 0~3(4 carrier RRU)
carrier RRU)
 REGULAR
(Regular
Installation
Scenario: One RET
antenna connects
to one antenna
connector for
signal
transmission),
SECTOR_SPLITTI
NG (Sector
Splitting Scenario:
A number of RET
antennas transmit
signals to cover
one cell in which REGULAR,
Enumeration the single sector is SECTOR_SPLITTIN
Antenna Line Device Scenario None
Type logically divided G, DAISY_CHAIN,
into multiple sub- 2G_EXTENSION
sectors),
DAISY_CHAIN
(Antenna
Cascaded
Scenario: A
number of RET
antennas are
sequentially
connected to a
single cable),
2G_EXTENSION
(2G Extension
Scenario: Control
the RET antennas
of 2G networks by
Frame Error Rate
DisappearThreshold of FE MAC Interval Type 0~100 0~0.1, Step: 0.001 None
Layer

Enabled State of the SSL Enumeration DISABLE(Disable),

Disable, Enable None
Certificate Chain Type ENABLE(Enable)

MASTER(Master
A flag, which indicates whether the
Enumeration Channel),
OM channel is the master one or MASTER, SLAVE None
Type SLAVE(Slave
the slave one.
Channel)
DISABLE(Disable
FPMUX Switch, which is a switch
Enumeration FP multiplexing),
to enable or disable FP DISABLE, ENABLE None
Type ENABLE(Enable
multiplexing.
FP multiplexing)

Name of the SSL Certificate Chain A string of up to 64

String Type None None
File characters
 BEST_EFFORT
(Best effort), BEST_EFFORT,
Fault Handling Mode for Failure in Enumeration
BREAK_ON_FAIL BREAK_ON_FAILU None
Running the Batch Command Files Type
URE (Break on RE
failure)

Enumeration COMPRESSED, COMPRESSED,

Compress Flag None
Type UNCOMPRESSED UNCOMPRESSED

Number of the RX Channel in the

Interval Type 0~1 0~1 None
Initial RTWP Adjusting

Enumeration
CHR Switch ON, OFF ON, OFF None
Type

Enumeration
CHR Type ALL, ABNORMAL ALL, ABNORMAL None
Type

Value of the Change Time in

Interval Type 5~600 5~600 None
Starting the RTWP Routine Test

BS (Channel of
Type of the Channel in Setting the Enumeration
BS), UMTS BS, UMTS None
SASU Gain Type
(Channel of UMTS)

Frame Max Length, which

indicates the maximum length of
Interval Type 100~1031 100~1031 byte
the FP, without the IP/UDP header
after multiplexing.

Timer_Idle. Length of the SSCOP

timer Timer_Idle specified in the
SAAL-related protocol. The value
Interval Type 100~65535 100~65535 ms
of this parameter should be larger
than or equal to the value of
KATM.
Interface Number Interval Type 0~15 0~15 None

PPP(PPP),
Enumeration
Interface Type MPGRP(MLPPP PPP, MPGRP None
Type
GROUP)

75(the line
workmode is E1),
Enumeration 120(the line
E1 or T1 line Impendance 75, 120, 100 ohm
Type workmode is E1),
100(the line
workmode is T1)
 GPSCARD (GPS
card clock source),
LINE(LINE clock
Enumeration GPSCARD, LINE,
Clock Source Type of the NodeB source), IPCLK(IP None
Type IPCLK, PTP, PEER
clock source),
PTP(PTP clock
source), PEER

BASE_BOARD,
Sub-Board Type of the E1/T1 Enumeration BASE_BOARD,
E1_COVERBOAR None
Routine Test Type E1_COVERBOARD
D
 Enumeration MASTER(Master
Cabinet No. MASTER None
Type cabinet)

Cabinet No. of Power

Enumeration MASTER(Master
Amplifier1:Power Amplifier refers to MASTER None
Type cabinet)
the power amplify unit in RRU.

Cabinet No. of Power

Enumeration MASTER(Master
Amplifier2:Power Amplifier refers to MASTER None
Type cabinet)
the power amplify unit in RRU.
 Enumeration MASTER(Master
Cabinet No. of RRU Begin MASTER None
Type cabinet)

Enumeration MASTER(Master
Cabinet No. of RRU End MASTER None
Type cabinet)

Enumeration MASTER(Master
Cabinet No. of DL Process Unit 1 MASTER None
Type cabinet)

Enumeration MASTER(Master
Cabinet No. of UL Process Unit 1 MASTER None
Type cabinet)

Enumeration MASTER(Master
Cabinet No. of DL Process Unit 2 MASTER None
Type cabinet)

Enumeration MASTER(Master
Cabinet No. of UL Process Unit 2 MASTER None
Type cabinet)

Enumeration MASTER(Master
Cabinet No. of DL Process Unit 3 MASTER None
Type cabinet)

Enumeration MASTER(Master
Cabinet No. of UL Process Unit 3 MASTER None
Type cabinet)

Enumeration MASTER(Master
Cabinet No. of DL Process Unit 4 MASTER None
Type cabinet)

Enumeration MASTER(Master
Cabinet No. of UL Process Unit 4 MASTER None
Type cabinet)

Operator Index Interval Type 0~65535 0~65535 None

A string of up to 31 A string of up to 31
Operator Name String Type None
bytes bytes

Connection Type Value of the Enumeration

ALL(ALL Type) ALL None
Accepted Connection Type
Statistic Count Interval Type 0~65535 0~65535 None

SAMEZONE
(Same Cover
Enumeration SAMEZONE,
Cover Type of Sector Type), DIFFZONE None
Type DIFFZONE
(Different Cover
Type)

IP Address. The local IP cannot be

the same as the peer IP address.
The value range should meet the
following conditions: The IP
address is of legal A, B, or C type
but cannot be the reserved IP
0.0.0.0~255.255.255.
address 0.x.x.x or 127.x.x.x. The IP IP Address Type - None
255
& ~mask cannot be 0, the IP &
mask cannot be 0, the IP & mask
+ ~mask cannot be 0xffffffff, and
the IP & ~mask + mask cannot be
0xffffffff. Note that "~mask"
indicates the complement on mask.
Local IP Address. The local IP
address cannot be the same as the
peer IP address. The value range
should meet the following
conditions: The IP address is of
legal A, B, or C type but cannot
be the reserved IP address 0.x.x.x 0.0.0.0~255.255.255.
IP Address Type - None
or 127.x.x.x. The IP & ~mask 255
cannot be 0, the IP & mask cannot
be 0, the IP & mask + ~mask
cannot be 0xffffffff, and the IP &
~mask + mask cannot be 0xffffffff.
Note that "~mask" indicates the
complement on mask.

CQI Filter Alpha of HSDPA Interval Type 0~99 0~99 None

A string of up to 64
Name of the Cancelled List File String Type None None
characters

Enable State of the Cancelled List Enumeration DISABLE(Disable),

Disable, Enable None
File Type ENABLE(Enable)

State Indicating Whether the RRU

CONFIGED
is Connected to an Auxiliary Power
Enumeration (Configed), CONFIGED,
System None
Type NOTCONFIGED NOTCONFIGED
State Indicating Whether the CMU
(Not Configed)
is configured

Cold Start Load Shutdown Flag of Enumeration ENABLE,

ENABLE, DISABLE None
the NEMU Type DISABLE

Cold Start Load Shutdown degre

Interval Type -40~0 -40~0
Temperature of the NEMU e

Flag for Setting the CM Control Enumeration ON(turnon),

ON, OFF None
Switch Type OFF(turnoff)

Current DA Interval Type 255~65520 255~65520 None

DA Interval Type 255~65520 255~65520 None

Installation Date Interval Type 1~31 1~31 None

Format: Format:
Start Time Compound Type None
YYYY&MM&DD YYYY&MM&DD

Lasting days Interval Type 0~65535 0~65535 None

Dead Band of the NCMU Heat Celsi

Interval Type 0~30 0~30
Control Delta Parameter us

Destination Cell ID Interval Type 0~65535 0~65535 None

The First Destination Cell ID Interval Type 0~65535 0~65535 None

The Second Destination Cell ID Interval Type 0~65535 0~65535 None

 0~65535*0.2,
SASU DC Load Interval Type 0~65535 mA
Step:0.2

BS (Supplied by
BS), UMTS
Enumeration
SASU DC Switch State (Supplied by BS, UMTS, OFF None
Type
UMTS), OFF
(OFF)

DC Upper Limit of the NPMU 58.0~60.0, Precision:

Any Type 58.0~60.0 V
AC/DC Voltage Alarm Threshold 0.01
DC Lower Limit of the NPMU 35.0~55.6, Precision:
Any Type 35.0 ~ 55.6 V
AC/DC Voltage Alarm Threshold 0.01

Delayed Discharge Test Time Interval Type 1~60 1~60 d

Default Power Level; use it when

Interval Type 10~100 10~100 %
Sector Type is Distributed Sector.

DISABLE(Not Join
in Transmission
Enumeration Resource Group),
Join Resource Group DISABLE, ENABLE None
Type ENABLE(Not Join
in Transmission
Resource Group)

Timer_Keep_Alive. Length of the

SSCOP timer Timer_Keep_Alive
Interval Type 100~65534 100~65534 ms
specified in the SAAL-related
protocol.
 SINGLE_RET
(Single-antenna
Remote Electrical
Tilt), STMA (Smart
Tower-mounted
SINGLE_RET,
Enumeration Amplifier),
Device Type STMA, None
Type MULTI_RET (Multi-
MULTI_RET, SASU
antenna Remote
Electrical Tilt),
SASU (Same band
Antenna Sharing
Unit)

SINGLE_RET
(Single-antenna
Remote Electrical
Tilt), STMA (Smart
Tower-mounted
SINGLE_RET,
Enumeration Amplifier),
Device Type STMA, None
Type MULTI_RET (Multi-
MULTI_RET, SASU
antenna Remote
Electrical Tilt),
SASU (Same band
Antenna Sharing
Unit)
SINGLE_RET
(Single-antenna
Remote Electrical
Type of the Antenna Line Device Enumeration SINGLE_RET,
Tilt), MULTI_RET None
(ALD) Type MULTI_RET
(Multi-antenna
Remote Electrical
Tilt)

Enumeration
AISG Protocl Version V1.1, V2.0_3GPP V1.1, V2.0_3GPP None
Type

Destination FACH Channel ID Interval Type 0~255 0~255 None

The First Destination FACH

Interval Type 0~255 0~255 None
Channel ID

The Second Destination FACH

Interval Type 0~255 0~255 None
Channel ID

Local IP Address. The local IP

address can be 0.0.0.0. If the local
IP address is not 0.0.0.0, it should 0.0.0.0~255.255.255.
IP Address Type - None
belong to legal A, B, or C type but 255
cannot be the reserved IP address
0.x.x.x or 127.x.x.x.
To match the uplink coverage
capability with the downlink
coverage capability,
desensitization is applied to reduce
the sensitivity of the receiver Interval Type - 0~30 dB
manually by adding proper noise to
received signals; if the
desensitization intensity is set to 0,
the desensitization is not applied.

COMMON_MODE(
Enumeration Common Mode), COMMON_MODE,
TX Diversity Mode of Sector None
Type HALFFREQ(0.5/0. HALFFREQ
5 Mode)

It refers to the downlink delay of

Interval Type 0~1000 0~1000 ns
the first antenna channel.

It refers to the downlink delay of

Interval Type 0~1000 0~1000 ns
the second antenna channel.

It refers to the downlink delay of

Interval Type 0~1000 0~1000 ns
the third antenna channel.
It refers to the downlink delay of
Interval Type 0~1000 0~1000 ns
the fourth antenna channel.

DL Frequency Channel Number Interval Type 0~65535 0~65535 None

It is the No. of the dllink resource

Interval Type 0~3 0~3 None
group.

It is the No. of the downlink

Interval Type 0~3 0~3 None
resource group.

Local IP Address. The local IP

address should belong to legal A,
B, or C type but cannot be the
reserved IP address 0.x.x.x or
0.0.0.0~255.255.255.
127.x.x.x. The parameter cannot IP Address Type - None
255
be equal to the other SCTP link IP
address. The parameter must be
the active interface address of this
board.

0.05C10 Discharge Time Any Type - 0.01~50.03 None

0.1C10 Discharge Time Any Type 0.01~50.01 0.01~50.03 None

0.2C10 Discharge Time Any Type 0.01~50.01 0.01~50.03 None

0.3C10 Discharge Time Any Type 0.01~50.01 0.01~50.03 None

0.4C10 Discharge Time Any Type 0.01~50.01 0.01~50.03 None

0.5C10 Discharge Time Any Type 0.01~50.01 0.01~50.03 None

0.6C10 Discharge Time Any Type 0.01~50.01 0.01~50.03 None

0.7C10 Discharge Time Any Type 0.01~50.01 0.01~50.03 None

0.8C10 Discharge Time Any Type 0.01~50.01 0.01~50.03 None

0.9C10 Discharge Time Any Type 0.01~50.01 0.01~50.03 None

IP Address Mask. A valid IP

address must meet all the following
conditions:
The IP & ~mask cannot be 0, the
IP & mask cannot be 0, the IP &
mask + ~mask cannot be 0xffffffff,
0.0.0.0~255.255.255.
and the IP & ~mask + mask cannot IP Address Type - None
255
be 0xffffffff.
Note that "~mask" indicates the
complement on the mask. The
mask cannot be 255.255.255.254.
The mask in binary does not allow
"0" before "1", or "1" after "0".

Daylight Saving Time Flag (If it is

Enumeration
not specified, the DST settings do - YES, NO None
Type
no change.)

Valid absolute path of the

A string of up to 120
destination on FTP SERVER, not String Type None None
bytes
including the file name
Local IP Mask. A valid IP address
must meet all the following
conditions:
The IP & ~mask cannot be 0, the
IP & mask cannot be 0, the IP &
mask + ~mask cannot be 0xffffffff,
0.0.0.0~255.255.255.
and the IP & ~mask + mask cannot IP Address Type - None
255
be 0xffffffff.
Note that "~mask" indicates the
complement on the mask. The
mask cannot be 255.255.255.254.
The mask in binary does not allow
"0" before "1", or "1" after "0".
Max Connection Control Count,
which indicates the maximum
number of connections or releases
Interval Type - 1~255 None
specified in SAAL-related protocol,
that is the maximum permitted
number of retransmissions
Max STAT Count, which indicates
the maximum number of list
elements in STAT PDU specified in Interval Type 3~65535 3~65535 None
SAAL-related protocol. It must be
an odd number.
Max Poll Data Count, which
indicates the maximum number of
Interval Type 1~65535 1~65535 None
times of polling data transmissions
specified in SAAL-related protocol.

Discharge Test Time Limit of the

Interval Type 1~100 1~100 None
Battery Capacity Test

Destination Port No. Range Type 0~7 0~7 None

Destination Fraatm Link No. Range Type 0~7 0~7 None

Destination Port No. Range Type 0~7 0~7 None

IMA(Bearing Port
Type is IMA),
UNI(Bearing Port
Enumeration
Destination Port Type Type is UNI), IMA, UNI, FRAATM None
Type
FRAATM(Bearing
Port Type is
FRAATM)
The value range is The value range is
30~20999 when 30~20999 when rate
rate unit is kbps; unit is kbps; kbps
Min Cell Rate Interval Type The value range is The value range is or
71~49526 when 71~49526 when rate cell/s
rate unit is cell per unit is cell per
second; second;

Enumeration BASE_BOARD(ba
Destination Subboard Type BASE_BOARD None
Type se board)

E1_COVERBOAR
Enumeration
Destination Subboard Type D(E1/T1 cover E1_COVERBOARD None
Type
board)

Destination Slot No. Range Type 0~7 0~7 None

Destination Slot No. Range Type 0~7 0~7 None

Destination Subrack No. Range Type 0 0 None

Enumeration
Bearing Mode ATM, IPV4 ATM, IPV4 None
Type

Next Hop IP. A valid IP address

must satisfy all the following
0.0.0.0~255.255.255.
conditions:Legal A/B/C type IP IP Address Type - None
255
address. IP address can not be
0.0.0.0 and 255.255.255.255.

Timer_No_Response. Length of
the SSCOP timer timer
Interval Type 101~65535 101~65535 ms
Timer_No_Response specified in
the SAAL-related protocolIt.

Refers to OM priority Interval Type 0~63 0~63 None

Dynamic Code Resource Enumeration

OPEN, CLOSE OPEN, CLOSE None
Distribuiton Switch of HSDPA Type
 FIXED (Fixed
transmit power),
RNC_BASED
(Dynamic transmit
power control
based on the Pilot
of DPCH or F-
DPCH),
FOLLOW_TPC
(Dynamic transmit FIXED,
power control RNC_BASED,
Enumeration
E-AGCH power control policy based on the TPC FOLLOW_TPC, None
Type
of DPCH or F- CQI_BASED,
DPCH), HSSCCH_BASED
CQI_BASED
(Dynamic transmit
power control
based on CQI),
HSSCCH_BASED
(Dynamic transmit
power control
based on HS-
SCCH)

Whether to set the E-AGCH power Enumeration

NO, YES NO, YES None
control parameters or not Type

This parameter specifies the power

offset of the E-AGCH from the -35~15 dB, step: 0.1
Interval Type -350~150 dB
power of the Common Pilot dB
Channel.

E-AGCH Power Offset; An offset is

added to the power of the current 2
ms sub-frame based on the TPC
-32~31.75 dB, step:
field power of its corresponding Interval Type 0~255 dB
0.25 dB
DPCCH. This offset is related to
the Signal-to-Noise Ratio
difference.

The value range is The value range is

30~20999 when 30~20999 when rate
rate unit is kbps; unit is kbps; kbps
Peak cell rate of ATM channel. Interval Type The value range is The value range is or
71~49526 when 71~49526 when rate cell/s
rate unit is cell per unit is cell per
second; second;
 Format:
End Date of the E1/T1 Routine YYYY&MM&DD, for
Compound Type None None
Test example:
2001&05&09

End Date of the Daylight Saving

Interval Type 1~31 1~31 None
Time

Battery Charge Efficiency Interval Type 80~100 80~100 %

EFFICIENT~0(Effic EFFICIENT~0(Efficie
Enumeration ient) nt)
Effect Signal None
Type UNEFFICIENT~1( UNEFFICIENT~1(No
Not Efficient) t Efficient)

End Mode of the Daylight Saving Enumeration DATE, WEEK, DATE, WEEK,
None
Time Type DATEWEEK DATEWEEK

JAN(January),
FEB(February),
MAR(March),
APR(April),
MAY(May), JAN, FEB, MAR,
End Month of the Daylight Saving Enumeration JUN(June), APR, MAY, JUN,
None
Time Type JUL(July), JUL, AUG, SEP,
AUG(August), OCT, NOV, DEC
SEP(September),
OCT(October),
NOV(November),
DEC(December)
 Auto(Automatic),
Transport Encryption Mode of the Enumeration Plaintext(Plaintext), Auto, Plaintext,
None
FTPS Client Parameter Type Encrypted(SSL Encrypted
encrypted)

End Voltage Of Battery Capacity 1.70~2.20, Precision:

Interval Type 1.70~2.20 V/cell
Test 0.01

Peer IP Address, which is of legal

A, B, or C type but cannot be the
reserved IP address 0.x.x.x or
127.x.x.x. The IP & ~mask cannot
be 0, the IP & mask cannot be 0, 0.0.0.0~255.255.255.
IP Address Type - None
the IP & mask + ~mask cannot be 255
0xffffffff, and the IP & ~mask +
mask cannot be 0xffffffff.
Note that "~mask" indicates the
complement on the mask.

Peer IP Mask. The IP & ~mask

cannot be 0, the IP & mask cannot
be 0, the IP & mask + ~mask
cannot be 0xffffffff, and the IP &
0.0.0.0~255.255.255.
~mask + mask cannot be 0xffffffff. IP Address Type - None
255
Note that "~mask" indicates the
complement on the mask. The
mask in binary allows no "0" before
"1" or "1" after "0".

Format:HOUR
End Time of the Daylight Saving (hour)& MIN
Compound Type None None
Time (At a Non-DST). (minute)& SEC
(second)
 Format:HOUR
End Time of the E1/T1 Routine (hour)& MIN
Compound Type None None
Test (minute)& SEC
(second)

SUN(Sunday),
MON(Monday),
TUE(Tuesday), SUN, MON, TUE,
End Week of the Daylight Saving Enumeration
WED(Wednesday), WED, THU, FRI, None
Time Type
THU(Thursday), SAT
FRI(Friday),
SAT(Saturday)
FIRST(First),
SECOND(Second), FIRST, SECOND,
End Week Sequence of the Enumeration
THIRD(Third), THIRD, FOURTH, None
Daylight Saving Time Type
FOURTH(Fourth), LAST
LAST(Last)

Float-Charging Voltage of the 43.2~57.6, Precision:

Any Type 43.2~57.6 V
NPMU 0.1

Peer UDP Port is one of the

parameters between NodeB and Interval Type 1024~3584 1024~3584 None
RNC.

PLR Appearing Threshold Interval Type 0~100 0~0.1, Step: 0.001 None
Packet Loss Rate Disappearing
Threshold, and its value shall not Interval Type 0~100 0~0.1, Step: 0.001 None
be larger than the PLRAT value.

Timer_Poll. Length of the SSCOP

timer Timer_Poll specified in the Interval Type 100~65534 100~65534 ms
SAAL-related protocol.

Download Configuration File Enumeration DISABLE(Disable),

ENABLE, DISABLE None
Enable Flag Type ENABLE(Enable)

Enumeration ENABLE,
MPT Backup Flag ENABLE, DISABLE None
Type DISABLE

RRU Installation Floor Interval Type -100~1000 -100~1000 None

Route Preference Interval Type 1~255 1~255 None

IPPRECEDENCE(
According to the
Priority Rule, according to the precedence value
Enumeration IPPRECEDENCE,
precedence in the TOS field or the in the TOS field), None
Type DSCP
DSCP field DSCP(According to
the DSCP value in
the TOS field)
Resource Group ID Interval Type 0~3 0~3 None

NEXTHOP(IP
Enumeration
Route type option address of the next NEXTHOP, IF None
Type
hop), IF(Out port)

Rx Bandwidth of this resource

Interval Type 32~15800 32~15800 kbit/s
group

The value range is The value range is

30~6759 when rate 30~6759 when rate
unit is kbps; unit is kbps; kbps
Sustain Cell Rate Interval Type The value range is The value range is or
71~15942 when 71~15942 when rate cell/s
rate unit is cell per unit is cell per
second; second;
The value range is The value range is
30~6759 when rate 30~6759 when rate
unit is kbps; unit is kbps; kbps
Sustain Cell Rate Interval Type The value range is The value range is or
71~15942 when 71~15942 when rate cell/s
rate unit is cell per unit is cell per
second; second;
Signaling priority.
IPPRECEDENCE: 0 (lowest) and 7
(highest)
DSCP: 000000 (for default PHB)
and XXX000 (for Class-Selector
PHB), where X is 0 or 1.
The service level is consistent with
Interval Type 0~63 0~63 None
the IP Precedence in the existing
network. For Expedited Forwarding
PHB, DSCP is 101110. For
Assured Forwarding PHB, four
service levels (bandwidth and
buffer size) and three packet
discard priorities are listed here.

CBR(Constant Bit
Rate),
Bearing Service Type. When the RTVBR(Real Time
value is CBR or UBR, only PCR Variable Bit Rate),
needs to be set; when the value is NRTVBR(Non-Real CBR, RTVBR,
Enumeration
RTVBR or NRTVBR, both PCR Time Variable Bit NRTVBR, UBR, None
Type
and SCR need to be set; when the Rate), UBR+
value is UBR+, both PCR and UBR(Unspecified
MCR need to be set. Bit Rate),
UBR_PLUS(Unspe
cified Bit Rate+)

TMA Gain Interval Type 0~255 0~255*0.5, Step:0.5 dB

Antenna Gain Range Type 0~255 0~25.5, Step:0.1 dB

Antenna Gain Range Type 0~255 0~25.5, Step:0.1 dB

Antenna Gain Range Type 0~255 0~25.5, Step:0.1 dB

Antenna Gain Range Type 0~255 0~25.5, Step:0.1 dB

GPS Cable Delay Interval Type 0~1000 0~1000 None

Enumeration MASTER(Master
Number of the Head Cabinet MASTER None
Type cabinet)

FALSE (Not
Enumeration
Two Tx Way of the Local Cell Support), TRUE FALSE, TRUE None
Type
(Support)

FALSE (Not
High Speed Movement Mode of Enumeration
Support), TRUE FALSE, TRUE None
the Local Cell Type
(Support)

Humidity Lower Limit Interval Type 5.00~95.00 5.00~95.00 %

Local Cell Inner Handover Radius Interval Type 0~200000 0~200000 m

Optical Port Number of the Head 0~2(WBBPa),

Interval Type 0~5 None
Interface Board 0~5(WBBPb)

Slot Number of the Head Interface

Interval Type 2~3 2~3 None
Board

Number of the Head Subrack Interval Type 0 0 None

High Temperature Critical Point of
Celsi
the NCMU Heat Control Delta Interval Type -99~70 -99~70
us
Parameter

Heater Close Temperature of the Celsi

Interval Type -99~40 -99~40
NCMU Heater Parameter us
High Temperature at the Delta Air
Celsi
Outlet of the NCMU Heat Control Interval Type 0~30 0~30
us
Delta Parameter

Celsi
Heater Start Temperature Interval Type -99~40 -99~40
us

Humidity Upper Limit Interval Type 5.00~95.00 5.00~95.00 %

Horizontal Position of the RRU Interval Type 0~1000 0~1000 None

 CBR(Constant Bit
Rate),
Bearing Service Type. When the RTVBR(Real Time
value is CBR or UBR, only PCR Variable Bit Rate),
needs to be set; when the value is NRTVBR(Non-Real CBR, RTVBR,
Enumeration
RTVBR or NRTVBR, both PCR Time Variable Bit NRTVBR, UBR+, None
Type
and SCR need to be set; when the Rate), UBR
value is UBR+, both PCR and UBR_PLUS(Unspe
MCR need to be set. cified Bit Rate+),
UBR(Unspecified
Bit Rate)

Sub Frame Max Length, which

indicates the maximum length of
the FP before multiplexing. The FP
Interval Type 1~1023 1~1023 byte
can be multiplexed only when its
frame length is smaller than this
value.

STATIC_BW_SHA
STATIC_BW_SHAPI
PING,
NG,
DYNAMIC_BW_S
DYNAMIC_BW_SHA
Enumeration HAPING,
Flow Control Switch PING, None
Type NO_BW_SHAPIN
NO_BW_SHAPING,
G,
BW_SHAPING_ON
BW_SHAPING_O
OFF_TOGGLE
NOFF_TOGGLE
 BOTTOM (Offset to
bottom, that is,
offset to the
minimum value
(The interference
signal frequency is
greater than or
equal to the current
receive
frequency.)),
MIDDLE (Offset to
middle, that is,
there is no offset
(no interference).),
TOP (Offset to top,
BOTTOM, MIDDLE,
that is offset to the
TOP, MINUS_50M,
WRFU/RRU IF Offset Indicating Enumeration maximum value
PLUS_50M, None
the Direction of IF Filter. Type (The interference
MINUS_75M,
signal frequency is
PLUS_75M
smaller than the
current receive
frequency.)),
MINUS_50M (Only
4 carrier RRU
support),
PLUS_50M (Only 4
carrier RRU
support),
MINUS_75M (Only
4 carrier RRU
support),
PLUS_75M (Only 4
carrier RRU
support).
Time Delay. The link is not
congested when the delay is lower Interval Type 0~100 0~500, Step: 5ms ms
than this threshold.

This parameter indicates the

Interval Type 1~20 1~20 ms
duration of Timer.

Transmission Link Fault Recover Enumeration DISABL(Disabl),

DISABLE, ENABLE None
Switch Type ENABLE(Enable)

RECOVEDRX(the
clock recovered
from optical signals
received by the
Enumeration RECOVEDRX,
Tx Clock receive end), None
Type EXT8K
EXT8K(external
8kHz clock
transmitted from
NMPT to NUTI)
Bearing VCI Interval Type 32~511 32~511 None

Analog Port Number of the NEMU

Standby Analog Value Input Interval Type 0~3 0~3 None
Parameters

Bearing VPI Interval Type 0~255 0~255 None

Committed Burst Size Interval Type 32~155000 32~155000 kbit

A string of up to 6
Installation Date String Type None None
bytes

A string of up to 5
Installer's ID String Type None None
bytes

Committed Information Rate, ETH:32~100000

ETH:32~100000
which is related to a specific MPGRP:32~31744
Interval Type MPGRP:32~31744 kpbs
physical interface but lower than ETHTHK:32~1000
ETHTHK:32~100000
the physical interface rate. 00
Committed Information Rate, ETH:32~100000
ETH:32~100000
which is related to a specific MPGRP:32~31744
Interval Type MPGRP:32~31744 kbps
physical interface but lower than ETHTHK:32~1000
ETHTHK:32~100000
the physical interface rate. 00

Duplex. Interface duplex mode.

The value can be forced full- Enumeration
FULL(Full-Duplex) FULL None
duplex. If the value is null, the Type
duplex mode is not modified.

Unicast address in
IP Address of the NTP Server IP Address Type None 0.0.0.1~255.255.255. None
254

0.0.0.0~255.255.255.
IP address of the FTP Serve IP Address Type None None
255

E1_DOUBLE_FRA
ME (Double
framtype for E1),
E1_CRC4_MULTI_ E1_DOUBLE_FRAM
FRAME (CRC4 E,
Mutipiy framtype E1_CRC4_MULTI_F
Frame Structure. If this parameter
Enumeration for E1), RAME,
is not specified, the original value None
Type T1_SUPER_FRAM T1_SUPER_FRAME
is kept.
E (Super framtype ,
for T1), T1_EXTENDED_SU
T1_EXTENDED_S PER_FRAME
UPER_FRAME
(Extended Super
framtype for T1)
DISABLE(Disable
Function. DISABLE means the LR settings on
disabling the LR settings on the Enumeration the port),
DISABLE, ENABLE None
port. ENABLE means enabling the Type ENABLE(Enable
LR settings on the port. the LR settings on
the port)
Auto or Manual IP Clock Enumeration AUTO(Auto),
AUTO, MANUAL None
Synchronization Mode Type MANUAL(Manual)

This parameter indicates whether

ENABLE(Insert
to add the VLAN tag. DISABLE
Enumeration VLAN Tag),
means not adding the VLAN tag, ENABLE, DISABLE None
Type DISABLE(not
and ENABLE means adding the
Insert VLAN Tag)
VLAN tag.
 NOLOOP
(loopback mode is
cancelled.),
LOCAL (Local end
loopback, which
means that data
goes through a
loop within a
NodeB instead of
through E1 cables.
It is used to check
Enumeration whether the NOLOOP, LOCAL,
Loopback Mode of E1/T1 None
Type transmission chips REMOTE
are normal..),
REMOTE (Remote
loopback, which
means that data
goes through a
loop of E1 cables
between NodeB
and RNC. it is used
to check whether
the E1 cables are
normal.)

NOLOOP (No
loop), ALL (ALL IP
Address), IPADDR NOLOOP,
(Appointed IP ALLLOOP,
Enumeration
Loopback Mode of IP Level Address), ONLYIPADDR, None
Type
IPADDRADDUDP IPADDRANDUDPP
PORT (Appointed ORT
IP Address and
UDP port No.)

Load Overtemperature Shutdown Enumeration ENABLE,

ENABLE, DISABLE None
Flag Type DISABLE

Automatic Alarm Handling Limit

Interval Type 15~30 15~30 None
After the VSWR Alarm

Lower Threshold of the Input 36.00~43.00,

Any Type 36.00~43.00 V
Voltage Alarm of the NEMU Precision: 0.1

Lower Alarm Occur Limit Any Type None None None

 NOLOOP
(loopback mode is
cancelled.),
REMOTE (Remote
loopback, which
means that data
goes through a
loop of fibers
betweenNodeB
and RNC/BSC. it is
used to check
Enumeration whether the fibers NOLOOP, LOCAL,
Loopback Mode None
Type are normal.), REMOTE
LOCAL (Local end
loopback, which
means that data
goes through a
loop within a
NodeB instead of
through fibers. It is
used to check
whether the
transmission chips
are normal.)

Line Code. If this parameter is not HDB3(HDB3 code

Enumeration
specified, the original value is for E1), AMI(AMI HDB3, AMI None
Type
kept. code for E1or T1)

AMI(AMI code for

Line Code. If this parameter is not
Enumeration E1or T1),
specified, the original value is AMI, B8ZS None
Type B8ZS(B8ZS code
kept.
for T1)

Loopback Time Range Type 1~60 1~60 min

Peer IP Address, which is of legal
A, B, or C type but cannot be the
reserved IP address 0.x.x.x or
127.x.x.x. The IP & ~mask cannot
be 0, the IP & mask cannot be 0, 0.0.0.0~255.255.255.
IP Address Type - None
the IP & mask + ~mask cannot be 255
0xffffffff, and the IP & ~mask +
mask cannot be 0xffffffff.
Note that "~mask" indicates the
complement on the mask.
ENABLE(Scramble
, it must be
ENABLE, when
Enumeration
Scramble Mode E1/T1 adopts AMI ENABLE, DISABLE None
Type
mode),
DISABLE(No
scramble)
Speed mode. The value can be
forced 10 Mbps, forced 100 Mbps,
10M(Forced
or auto-negotiated. It must be
10Mbps), Ethernet electrical
consistent with the peer IP
Enumeration 100M(Forced port: 10M, 100M,
interface. If the value is null, the None
Type 100Mbps), AUTO; Ethernet
speed is not modified.
AUTO(Auto- optical port: 100M
Value range: 10M (Forced 10
negotiation)
Mbps), 100M (Forced 100 Mbps),
AUTO (Auto-negotiation).

IP Clock Link Number Interval Type 0~1 0~1 None

This parameter indicates the DSCP

Interval Type 0~63 0~63 None
priority of the user data.

USERDATA
(USERDATA), SIG
Traffic Type, including user data, Enumeration (SIG DATA), OM USERDATA, SIG,
None
OM, SIG, and other types. Type (Maintenance OM, OTHER
DATA), OTHER
(OTHER)

VLAN Group No. Interval Type 0~3 0~3 None

Local Cell ID Interval Type 0~268435455 0~268435455 None

VLAN ID Interval Type 1~4094 1~4094 None

VLAN Priority, which indicates the

Interval Type 0~7 0~7 None
priority level of VLAN

Maximum number of transmission

units. It is the maximum length of
the IP packets on the port. If this Interval Type 46~1500 46~1500 None
parameter is not specified, the
MTU is not modified.

Minimum value of the timer for

Interval Type 0~255 0~255 min
disabling the cell transmitter

Enumeration ENABLE,
Load Shutdown Flag of the NEMU ENABLE, DISABLE None
Type DISABLE

35.0~55.6,
Load Shutdown Voltage Of NEMU Any Type 35.0~55.6 V
precision:0.1

Enumeration DISABLE,
Address & Control Field Compress DISABLE, ENABLE None
Type ENABLE
Low Temperature Critical Point of
Celsi
the NCMU Heat Control Delta Interval Type -99~70 -99~70
us
Parameter

Load Shutdown Temperature Interval Type 55~70 55~70 None

Low Temperature Threshold of the Celsi
Interval Type -40~10 -40~10
NCMU us

Enumeration
Manual Touchoff Switch ON, OFF ON, OFF None
Type

A hexadecimal
A hexadecimal string
string of 40
of 40 characters
characters
(excluding H').
(excluding H').
Format:
Format:
ATM Address, a hexadecimal H'390203040506070
H'39020304050607
string of 40 characters (excluding Any Type 80900010203040506 None
080900010203040
H'). 07080900. The ATM
50607080900. The
address must start
ATM address must
with 39, 45, or 47 to
start with 39, 45,
comply with the
or 47 to comply
protocols.
with the protocols.
 A hexadecimal
A hexadecimal string
string of 40
of 40 characters
characters
(excluding H').
(excluding H').
Format:
Format:
H'390203040506070
H'39020304050607
ATM Address Any Type 80900010203040506 None
080900010203040
07080900. The ATM
50607080900. The
address must start
ATM address must
with 39, 45, or 47 to
start with 39, 45,
comply with the
or 47 to comply
protocols.
with the protocols.

Adjacent Node ID Interval Type 0~31 0~31 None

-35~15 dB, step: 0.1

E-AGCH Max Power Interval Type -350~150 dB
dB

NONAUTH(no
authentication),
Enumeration PAP(PAP NONAUTH, PAP,
Authentication None
Type authentication), CHAP
CHAP(CHAP
authentication)
Auto Switch to Master Address.
When the master address is
Enumeration ENABLE,
restored, the service can be DISABLE, ENABLE None
Type DISABLE
switched to the master address
automatically.
NCP/CCP Bearing Type, which
indicates whether the Resource Enumeration
ATM, IPV4 ATM, IPV4 None
Group Bearing Type is configured Type
on the IP link or the ATM link.

0~50 dB, step: 0.1

Max RRU Output Power Interval Type 0~500 dB
dB

Enumeration
Resource Group Bearing Type IPV4 IPV4 None
Type

Bearing Type, which indicates

whether the Resource Group Enumeration
ATM, IPV4 ATM, IPV4 None
Bearing Type is configured on the Type
IP link or the ATM link.

102.4~1330000,
Cell Delay Variation Tolerance Interval Type 1024~13300000 us
Step: 0.1us
Client IP Address, which must be 0.0.0.0~255.255.255.
IP Address Type - None
the IP address of ETHPORT. 255

For the different links in a group

may go through different
ITC(Independent
transmission network, the links
Enumeration Transmit Clock),
may use the different synchronize ITC, CTC None
Type CTC(Common
source. In this case, the clock
Transmit Clock)
mode of the IMA group should be
ITC.

-35~15 dB, step: 0.1

E-AGCH Min TX Power Interval Type -350~150 dB
dB

CCP Port No.. It is valid when

Range Type 0~65535 0~65535 None
NCP/CCP Port Type is CCP.

Statistic Periods Interval Type 0~65535 0~65535 None

Measurement Lower Limit of the

0~4294967.295,
NEMU Standby Analog Value Input Any Type 0~4294967295 None
precision:0.001
Parameters

Enumeration NCP(NCP port),

NCP/CCP Port Type NCP, CCP None
Type CCP(CCP port)

NORMAL (Normal
Enumeration
SASU Mode Mode), BYPASS NORMAL, BYPASS None
Type
(Bypass Mode)
NORMAL (Normal
Enumeration
TMA Mode Mode), BYPASS NORMAL, BYPASS None
Type
(Bypass Mode)
 Enumeration
System Clock Working Mode MANUAL, FREE MANUAL, FREE None
Type

OFF(Disabled OFF(Disabled
mode), mode),
Enumeration DEFAULT(System DEFAULT(System
Work Mode None
Type default mode), default mode),
CUSTOM(User- CUSTOM(User-
defined mode) defined mode)

A string of up to 15
Antenna Model No. String Type None None
bytes
Diff Max Delay. The links in an IMA
group go through different
tranmission lines, which introduces
different transmission delays and
causes relative delay variation
Interval Type 4~100 4~100 ms
between the links (known as Link
Differential Delay). When the Link
Differential Delay exceeds the
capacity setting, the LODS alarms
related to the link are reported.

The identifier, the parameter can

not include the letters of '<', '>', String Type 0~64 characters 0~64 characters None
'?', '!', ''', '\' and '"'.

0.0.0.0~255.255.255.
DHCP Server IP Address IP Address Type - None
255

Differentiated Services Code Point.

Interval Type 0~63 0~63 None
Refer to [MML]SET DIFPRI[/MML].

Destination IP Address. This

parameter must meet all the
following conditions:
The IP address must be the one of
legal A, B, or C type, excluding
0.0.0.0~255.255.255.
the default route (IP address IP Address Type - None
255
0.0.0.0).
The IP & mask must be equal to
this IP address.
The mask in binary does not allow
"0" before "1", or "1" after "0".

Measurement Upper Limit of the

0~4294967.295,
NEMU Standby Analog Value Input Any Type 0~4294967295 None
precision:0.001
Parameters

Destination IP Mask. This

parameter must meet all the
following conditions:
0.0.0.0~255.255.255.
The IP & mask must be equal to IP Address Type - None
255
this IP address.
The mask in binary does not allow
"0" before "1", or "1" after "0".
The maximum transmit power of
the local cell is the maximum
output power at the antenna
connector on the cabinet top. The
Interval Type 0~500 0~50, step: 0.1 dB dB
value must stay within the value
range supported by the power
amplifier; otherwise, the local cell
is unavailable.

Every HSDPA user will limit the

power configured by the parameter Interval Type 1~100 1~100 %
value.

A string of up to 31
NodeB Name String Type None None
characters

Name of the SASU Which Needs A string of up to 31

String Type None None
Setting characters

Name of the RET Antenna of A string of up to 31

String Type None None
Which the Downtilt Needs Setting characters
Device Name of the Antenna Line A string of up to 31
String Type None None
Device (ALD) characters.

Device Name of the Smart Tower- A string of up to 31

String Type None None
Mounted Amplifier (STMA) characters.

Destination Resource Group ID Interval Type 0~3 0~3 None

A map of the
timeslot, denoted in
binary format. If a
timeslot is selected,
it is crossed to the
timeslot with the
TS1, TS2, TS3, same No. of E1 0. Or
TS4, TS5, TS6, else, it is not
TS7, TS8, TS9, crossed. Select
TS10, TS11, "SELECT ALL" or
Destination E1/T1 Time Slot No. A
TS12, TS13, "CLEAR ALL" to
map of the timeslot, denoted in
TS14, TS15, select or not select
binary format.
Enumeration TS16, TS17, all the timeslots. In
If a timeslot is selected, it indicates None
Type TS18, TS19, E1 mode,
that the timeslot is used; otherwise,
TS20, TS21, TS1~TS31
it indicates that the timeslot is not
TS22, TS23, respectively
used.
TS24, TS25, corresponds to
TS26, TS27, timeslots 1~31.
TS28, TS29, Timeslots 0 cannot
TS30, TS31 be configured. In T1
mode, TS1~TS24
respectively
corresponds to
timeslots 1~24, and
the other timeslots
are unavailable.

Destination Port VCI Interval Type 32~511 32~511 None

Destination Port VPI Interval Type 0~255 0~255 None

MASTER(Master
A flag, which indicates whether the
Enumeration Channel),
transmission channel is the master MASTER, SLAVE None
Type SLAVE(Slave
one or the slave one.
Channel)
 DISABLE(Disable
FPMUX Switch, which is a switch
Enumeration FP multiplexing),
to enable or disable FP DISABLE, ENABLE None
Type ENABLE(Enable
multiplexing.
FP multiplexing)

Fraatm Link No. Interval Type 0~7 0~7 None

FIXED (Fixed
transmit power),
RNC_BASED
(Dynamic transmit
power control
based on the Pilot
FIXED,
E-HICH power control policy for Enumeration of DPCH or F-
RNC_BASED, None
non-service radio link set Type DPCH),
FOLLOW_TPC
FOLLOW_TPC
(Dynamic transmit
power control
based on the TPC
of DPCH or F-
DPCH)

Whether to set the E-HICH power

Enumeration
control parameters for non-service NO, YES NO, YES None
Type
radio link set or not

This parameter specifies the power

offset of the E-HICH non-serving -35~15 dB, step: 0.1
Interval Type -350~150 dB
RLS from the power of the dB
Common Pilot Channel.
E-HICH Power Offset for Non-
service Radio Links Set. An offset
is added to the power of the current
2 ms sub-frame based on the TPC -32~31.75 dB, step:
Interval Type 0~255 dB
field power of its corresponding 0.25 dB
DPCCH. This offset is related to
the Signal-to-Noise Ratio
difference.
 FIXED (Fixed
transmit power),
RNC_BASED
(Dynamic transmit
power control
based on the Pilot
FIXED,
E-RGCH power control policy for Enumeration of DPCH or F-
RNC_BASED, None
non-service radio links Type DPCH),
FOLLOW_TPC
FOLLOW_TPC
(Dynamic transmit
power control
based on the TPC
of DPCH or F-
DPCH)
Whether to set the E-RGCH power
Enumeration
control parameters for non-service NO, YES NO, YES None
Type
radio links or not

This parameter specifies the power

offset of the E-RGCH non-serving -35~15 dB, step: 0.1
Interval Type -350~150 dB
RL from the power of the Common dB
Pilot Channel.

E-RGCH Power Offset for Non-

service Radio Links; an offset is
added to the power of the current 2
ms sub-frame based on the TPC -32~31.75 dB, step:
Interval Type 0~255 dB
field power of its corresponding 0.25 dB
DPCCH. This offset is related to
the Signal-to-Noise Ratio
difference.

Frame Max Length, which

indicates the maximum length of
Interval Type 100~1031 100~1031 byte
the FP, without the IP/UDP header
after multiplexing.

FRAMEMODE_SO
NET(The optical
port work in
SONET OC-3 FRAMEMODE_SON
Enumeration
Frame Mode mode), ET, None
Type
FRAMEMODE_SD FRAMEMODE_SDH
H(The optical port
work in SDH STM-
1mode)
Normal Temperature at the Delta
Celsi
Air Inlet of the NCMU Heat Control Interval Type 0~30 0~30
us
Delta Parameter

Normal Temperature at the Delta

Celsi
Air Outlet and Inlet of the NCMU Interval Type 0~30 0~30
us
Heat Control Delta Parameter

Object Alarm ID Interval Type 1~32000 1~32000 None

Object Number Interval Type 0~254 0~254 None

ALL(ALL),
BRD(Board),
E1/T1(E1/T1), ALL, BRD, E1/T1,
Enumeration
Type of Objects Needed Shielding E1/T1OnChannels E1/T1OnChannelsSu None
Type
Subbrd(E1/T1 On bbrd
Channels
Subboard)
Overcurrent Alarm Clearance
Threshold of the Antenna Line Interval Type 0~1000 0~1000 mA
Device (ALD)

D32(Tx Frame
Tx Frame Length. A longer Tx Length D32),
Frame Length brings about more D64(Tx Frame
efficient data transmission but Enumeration Length D64), D32, D64, D128,
None
lower sensitivity to data Type D128(Tx Frame D256
transmission errors. The default Length D128),
value is recommended. D256Tx Frame
Length D256)

On/Off Status of the Environment Enumeration

ON, OFF ON~0 OFF~1 None
Devices Type

Overcurrent Alarm Occurrence

Threshold Of ALD(Antenna Line Interval Type 0~1000 0~1000 mA
Device)

Enumeration
Operating Sort DEV, OPE DEV, OPE None
Type

Enumeration
ALD Protocl Version V1.1, V2.0_3GPP V1.1, V2.0_3GPP None
Type

NAME (ALD
Name), CSAT
(Cabinet No.,
Subrack No.,
Enumeration NAME, CSAT,
Operating Mode Antenna Connector None
Type SECTOR
No. and Device
Type), SECTOR
(Site No. and
Sector No.)
 ADDDESFACH(Ad
d destination FACH
It indicates whether you are adding
to CMB FACH_D
the destination FACH channel to
Enumeration Group), ADDDESFACH,
the CMB FACH_D group or None
Type DELDESFACH(Del DELDESFACH
deleting a destination FACH
ete destination
channel from the group.
FACH from CMB
FACH_D Group)

Over Temperature Threshold of the Celsi

Interval Type 20~80 20~80
NCMU us
Interface Number Interval Type 0~15 0~15 None

PPP(PPP),
Enumeration
Interface Type MPGRP(MLPPP PPP, MPGRP None
Type
GROUP)

IMA Group No. Interval Type 0~3 0~3 None

IMA Link No. Interval Type 0~7 0~7 None

This parameter indicates whether

ENABLE(Insert
to add the VLAN tag. DISABLE
Enumeration VLAN Tag),
means not adding the VLAN tag, ENABLE, DISABLE None
Type DISABLE(not
and ENABLE means adding the
Insert VLAN Tag)
VLAN tag.
IP Address. The local IP cannot be
the same as the peer IP address.
The value range should meet the
following conditions: The IP
address is of legal A, B, or C type
but cannot be the reserved IP
0.0.0.0~255.255.255.
address 0.x.x.x or 127.x.x.x. The IP IP Address Type - None
255
& ~mask cannot be 0, the IP &
mask cannot be 0, the IP & mask
+ ~mask cannot be 0xffffffff, and
the IP & ~mask + mask cannot be
0xffffffff. Note that "~mask"
indicates the complement on mask.

DISABLE(The IP
header is not
IP Header Compress. DISABLE expected to be
means that the IP header is not compressed from
expected to be compressed from Enumeration the peer),
DISABLE, ENABLE None
the peer end. ENABLE means that Type ENABLE(The
the UDP/IP header is expected to UDP/IP header is
be compressed from the peer end. expected to be
compressed from
the peer)

Local IP Mask. If the IP mask is

0.0.0.0, it indicates that the IP
mask must be negotiated; if the IP
mask is not 0.0.0.0, the following
conditions must be met: The IP &
~mask cannot be 0, the IP & mask
cannot be 0, the IP & mask + 0.0.0.0~255.255.255.
IP Address Type - None
~mask cannot be 0xffffffff, and the 255
IP & ~mask + mask cannot be
0xffffffff. Note that "~mask"
indicates the complement on the
mask. The mask in binary does not
allow "0" before "1", or "1" after
"0".

DISABLE(Not Join
in Transmission
Enumeration Resource Group),
Join Resource Group DISABLE, ENABLE None
Type ENABLE(Not Join
in Transmission
Resource Group)

Link No. Interval Type 0~1 0~1 None

No. of the SAAL link where the CP

Interval Type 0~63 0~63 None
is located.
SCTP Link No. Interval Type 0~19 0~19 None

No. of the SAAL link where the

Interval Type 0~63 0~63 None
AAL2 node is located.

Local IP Address. The parameter

must meet all the following
conditions:
The local IP address can be
0.0.0.0. If it is not 0.0.0.0, the IP
address is of legal A, B, or C but
cannot be the reserved IP address
0.x.x.x or 127.x.x.x.
The IP & ~mask cannot be 0, the
IP & mask cannot be 0, the IP & 0.0.0.0~255.255.255.
IP Address Type - None
mask + ~mask cannot be 0xffffffff, 255
and the IP & ~mask + mask cannot
be 0xffffffff.
Note that "~mask" indicates the
complement on the mask. If the IP
address is 0.0.0.0, it indicates that
the IP address must be negotiated;
if the IP address is not 0.0.0.0, it
cannot be the same as the peer IP
address.

Port Number of the RHUB Where

Interval Type 0~7 0~7 None
the Pico RRU is Located

Password Enabled State of the Enumeration DISABLE(Disable),

Disable, Enable None
Private Key File Type ENABLE(Enable)

Local SCTP Port, which is one of

the parameters between NodeB Interval Type 1024~65535 1024~65535 None
and RNC.
IP Address Mask. A valid IP
address must meet all the following
conditions:
The IP & ~mask cannot be 0, the
IP & mask cannot be 0, the IP &
mask + ~mask cannot be 0xffffffff,
0.0.0.0~255.255.255.
and the IP & ~mask + mask cannot IP Address Type - None
255
be 0xffffffff.
Note that "~mask" indicates the
complement on the mask. The
mask cannot be 255.255.255.254.
The mask in binary does not allow
"0" before "1", or "1" after "0".

Port Number of the E1/T1 Routine

Interval Type 0~7 0~7 None
Test
NEMU Port Number Interval Type 0~5 0~5 None

NPSU Number Interval Type 1~3 1~3 None

Alarm Port Number Interval Type 0~35 0~35 None

Port No. Range Type 0~7 0~7 None

Port No. Range Type 0~7 0~7 None

Bearing Port No. Range Type 0~7 0~7 None

Bearing Fraatm Link No. Range Type 0~7 0~7 None

Fraatm Link No. Range Type 0~7 0~7 None

Fraatm Link No. Range Type 0~7 0~7 None

Max Burst Size Interval Type 3~10000 3~10000 None

Port Number of the FTP Server
Interval Type 21~65535 21~65535 None
Providing the FTP Services

DISABLE(not use
Multi Class PPP. DISABLE means
Enumeration MCPPP),
not using MCPPP; ENABLE means DISABLE, ENABLE None
Type ENABLE(use
using MCPPP.
MCPPP)
The value range is The value range is
30~20999 when 30~20999 when rate
rate unit is kbps; unit is kbps; kbps
Min Cell Rate Interval Type The value range is The value range is or
71~49526 when 71~49526 when rate cell/s
rate unit is cell per unit is cell per
second; second;
The value range is The value range is
30~20999 when 30~20999 when rate
rate unit is kbps; unit is kbps; kbps
Min Cell Rate Interval Type The value range is The value range is or
71~49526 when 71~49526 when rate cell/s
rate unit is cell per unit is cell per
second; second;
Min Number of Links Activated,
which is a threshold indicating the
available status of IMA group. For
example, if this parameter is set to
3 and the number of activated IMA
links in an IMA group is larger than Interval Type 1~8 1~8 None
or equal to 3, then the IMA group
is available. If the number of
activated IMA links in the group is
smaller than 3, then the IMA group
is unavailable.

MLPPP Packets Discard Alarm

Interval Type 0~100 0~0.1, Step: 0.001 None
Appear Threshold

Name of the Private Key Certificate A string of up to 64

String Type None None
File characters

RRU Position in the Chain Interval Type 0~7 0~7 None

Power Supply Port of the Antenna Enumeration R0A, R0B, R0A, R0B,
None
Line Device (ALD) Type RET_PORT RET_PORT

-48VDC (-48V DC),

Enumeration -48VDC, 24VDC,
NodeB Power Supply Type 24VDC (24V DC), None
Type 220VAC
220VAC (220V AC)

BOOL(Boolean
Enumeration port), BOOL(Boolean port),
Port Type None
Type VALUE(Analog VALUE(Analog port)
port)

APM100,
Enumeration APM100, APM200,
Auxiliary Power System Type APM200, APM30, None
Type APM30, OMB
OMB

Name of the Public Key Certificate A string of up to 64

String Type None None
File characters

MLPPP Packets Discard Alarm

Interval Type 0~100 0~0.1, Step: 0.001 None
Disappear Threshold
 A string of up to 64
Private Key Password Password Type None None
characters

0~16 characters,
User password for login Password Type None excluding <, >, !, ?, : None
in the password

Power Margin Ratio, to prevent the

total power from exceeding the Interval Type 0~100 0~100 %
100% power margin in 2 ms.

DEFAULT(Use the
default power),
It is power setting mode of the Enumeration ABSOLUTE(Use DEFAULT,
None
RRU. Type this absolute power ABSOLUTE
value for power
amplifier)
Power Supply Switch of the
Enumeration
Antenna Line Device (ALD) ON, OFF ON, OFF None
Type
System

The radius of the local cell affects

Interval Type 150~200000 150~200000 m
its coverage.

Number of the RRU Chain/Ring Interval Type 0~249 0~249 None

ML PPP Group No. Interval Type 0~3 0~3 None

Index of remote cell group Interval Type 0~4294967295 0~4294967295 None

A string of up to 31
Name of remote cell group String Type None None
bytes

Maximum Receive Unit Interval Type 128~1500 128~1500 byte

Enumeration
RET Type DUAL DUAL None
Type

RF Desensitivity of the RRU Interval Type 0~10 0~10 None

ADDULPUNIT, ADDULPUNIT,
It indicates whether you are DELULPUNIT(MO DELULPUNIT(MOD
deleting the board from the Enumeration D ULGROUP) ULGROUP)
None
resource group or add a board to Type ADDDLPUNIT, ADDDLPUNIT,
the resource group. DELDLPUNIT(MO DELDLPUNIT(MOD
D DLGROUP) DLGROUP)
ENABLE (Support
Rollback Mode for Activating the Enumeration rollback),
ENABLE, DISABLE None
Baseline Type DISABLE (Not
support rollback)

Remote Cell Group Index of Local

Interval Type 0~4294967295 0~4294967295 None
Cell

FALSE (Not
Enumeration
Remote Mode of the Local Cell Support), TRUE FALSE, TRUE None
Type
(Support)

A string of up to 64
RRU Name String Type None None
characters

PPP MuxCP. DISABLE means DISABLE(Local

disabling the local protocol; Enumeration protocol disable),
DISABLE, ENABLE None
ENABLE means enabling the local Type ENABLE(Local
protocol. protocol enable)

A string of up to 64
Name of the Root Certificate File String Type None None
characters
Mode of RRU used in this local
cell; if Sector Type is Distributed
UNSYNC (use part
Sector, just use the sector type; if
of the sector
the mode is SYNC, the local cell Enumeration
RRUs), SYNC UNSYNC, SYNC None
uses all the RRUs in the sector Type
(use all of the
where the local cell is; if the mode
sector RRUs)
is UNSYNC, the local cell uses
specified RRUs.
UO (UMTS ONLY),
G/U (G/U DUAL
Enumeration MODE(Only MRRU UO~128 G/U~192
RRU Work Standard None
Type support)), GO GO~64
(GSM ONLY(Only
MRRU support))
CODE_PRI(Code
Priority:refers to
power limited cell),
POWER_PRI(Pow CODE_PRI,
Resource Allocate Method of Enumeration
er Priority:refers to POWER_PRI, None
HSDPA Type
code limited cell), POWERCODE_BAL
POWERCODE_BA
L(Balance between
Code and Power)
Next Hop IP Address. A valid IP
address must meet all the following
conditions:
0.0.0.0~255.255.255.
The IP address is of legal A, B, or IP Address Type - None
255
C type.
The IP address cannot be 0.0.0.0
or 255.255.255.255.
Next Hop IP. A valid IP address
must satisfy all the following
0.0.0.0~255.255.255.
conditions:Legal A/B/C type IP IP Address Type - None
255
address. IP address can not be
0.0.0.0 and 255.255.255.255.

Resource Limiting Switch of Enumeration OPEN (OPEN),

OPEN, CLOSE None
HSDPA Type CLOSE (CLOSE)

LATER(Later
NodeB Resetting Mode After the Enumeration reset), LATER,
None
Download of the Configuration File Type IMMEDIATELY(Im IMMEDIATELY
mediately reset)
Tscross No. Interval Type 0~15 0~15 None

Tree link PVC No. Interval Type 0~65535 0~65535 None

Enumeration MRRU, RHUB, MRRU, RHUB,

RRU Type None
Type PRRU, WRFU PRRU, WRFU

NodeB IP Address, which

indicates the NodeB IP address of
the IP port. It can be classified into
the following types:
When the NodeB IP address is
configured by the link Layer, the
configured address can be used. 0.0.0.0~255.255.255.
IP Address Type - None
When the DEVIP is configured, 255
the DEVIP address can be used.
When the NodeB IP address is
obtained by the link layer
negotiation, the negotiated
address cannot be used but can be
configured as 0.0.0.0.

Value of the RTWP Initial Adjusting Interval Type -130~130 -13~13, step 0.1 dB

LOCAL(End Node),
Enumeration
Node Type HUB(Switching LOCAL, HUB None
Type
Node)
PERFFIRST
(Handover
performance first
Resource Allocate Rule of Enumeration PERFFIRST,
mode), None
Baseband Type CAPAFIRST
CAPAFIRST
(Capacity first
mode)
LOCAL(End Node),
HUB(Switching
Enumeration LOCAL, HUB,
Node Type Node), None
Type ADJNODE
ADJNODE(Adjace
nt Node)

Index of the WRFU/RRU RX

Interval Type 0~1 0~1 None
Channel
RX Unit Number of the
Interval Type 0~1 0~1 None
WRFU/RRU

Enumeration ON (Switch on),

RX Unit Switch of the WRFU/RRU ON, OFF None
Type OFF (Switch off)

Path Check. DISABLE means not

using PING to detect the path Enumeration DISABLE,
DISABLE, ENABLE None
state; ENABLE means using PING Type ENABLE
to detect the path state.

IP Path ID Interval Type 0~65535 0~65535 None

AAL2 Path ID Interval Type 1~4294967295 1~4294967295 None

The value range is The value range is

30~20999 when 30~20999 when rate
rate unit is kbps; unit is kbps; kbps
Peak cell rate of ATM channel Interval Type The value range is The value range is or
71~49526 when 71~49526 when rate cell/s
rate unit is cell per unit is cell per
second; second;

YES (has a
Enumeration
Status of the Sub-Board subboard), NO YES, NO None
Type
(has no subboard)

UAEC, UPEC, UAEC, UPEC,

Enumeration
Sub-Board Type UUAS, UQEC, UUAS, UQEC, None
Type
UEOC UEOC
 BASE_BOARD(ba
BASE_BOARD(Base
se board),
Board),
E1_COVERBOAR
Enumeration E1_COVERBOARD(
Subboard Type D(E1/T1 cover None
Type E1 Coverboard),
board),
BACK_BOARD(Back
BACK_BOARD(ba
Board)
ck board)

BASE_BOARD(ba
BASE_BOARD(Base
se board),
Enumeration Board),
Subboard Type E1_COVERBOAR None
Type E1_COVERBOARD(
D(E1/T1 cover
E1 Coverboard)
board)

BASE_BOARD(ba
BASE_BOARD(Base
se board),
Board),
E1_COVERBOAR
Enumeration E1_COVERBOARD(
Subboard Type D(E1/T1 cover None
Type E1 Coverboard),
board),
BACK_BOARD(Back
BACK_BOARD(ba
Board)
ck board)
The power of the HS-SCCH is an
offset in dB to the transmit power
of the PCPICH. The power of the
-10~10 dB, step:
HS-SCCH is valid only when the Interval Type 0~80 dB
0.25 dB
power of the HS-SCCH is
controlled by predefined values.
The power is a fixed value.

Whether to set the Mac-e schedule Enumeration

NO, YES NO, YES None
parameters or not Type

Source logical Cell ID Interval Type 0~65535 0~65535 None

The value range is The value range is

30~20999 when 30~20999 when rate
rate unit is kbps; unit is kbps; kbps
Peak cell rate of ATM channel Interval Type The value range is The value range is or
71~49526 when 71~49526 when rate cell/s
rate unit is cell per unit is cell per
second; second;

Peer IP Address, which is of legal

A, B, or C type but cannot be the
reserved IP address 0.x.x.x or
127.x.x.x. The IP & ~mask cannot
be 0, the IP & mask cannot be 0, 0.0.0.0~255.255.255.
IP Address Type - None
the IP & mask + ~mask cannot be 255
0xffffffff, and the IP & ~mask +
mask cannot be 0xffffffff.
Note that "~mask" indicates the
complement on the mask.
Peer SCTP Port is one of the
parameters between NodeB and Interval Type 1024~65535 1024~65535 None
RNC.
Protocol Field Compress.
DISABLE means not being Enumeration DISABLE,
DISABLE, ENABLE None
compressed; ENABLE means Type ENABLE
being compressed.

ML PPP Link No. Interval Type 0~15 0~15 None

Route Preference Interval Type 1~255 1~255 None

Start Date of the E1/T1 Routine Format:

Compound Type None None
Test YYYY&MM&DD
Start Date of the Daylight Saving
Interval Type 1~31 1~31 None
Time

Simple Discharge End Voltage of 40.00~54.00,

Any Type 40.00~54.00 V
the Battery Capacity Test Precision: 0.01

Simple Discharge Time Limit of the

Interval Type 1~240 1~240 min
Battery Capacity Test

Password. It is mandatory if AUTH

Password Type 0~16 characters 0~16 characters None
is not NONAUTH.

It is sequentially numbered in the

site. Up to six sectors can be Interval Type 0~5 0~5 None
configured to one site.

Sector Number Interval Type 0~5 0~5 None

Receive Cell Rate. The RCR value

must be equal to the DL bandwidth
configured at the RNC. When the The value range is The value range is
AAL2PATH is configured at the 30~20999 when 30~20999 when rate
NodeB, the RCR will be used as rate unit is kbps; unit is kbps; kbps
the receive bandwidth, which is an Interval Type The value range is The value range is or
important parameter in the 71~49526 when 71~49526 when rate cell/s
algorithm for flow control. Whether rate unit is cell per unit is cell per
the RCR is configured correctly or second; second;
not will affect the result of the
algorithm for flow Control.

REMOTE_SECTO
Enumeration R (Remote Sector), REMOTE_SECTOR,
It indicates type of the sector. None
Type DIST_SECTOR DIST_SECTOR
(Distributed Sector)

A string of up to 4
Sector ID String Type None None
bytes
 A string of up to 32
Sector ID String Type None None
bytes

FIXED (Fixed
transmit power),
RNC_BASED
(Dynamic transmit
power control
based on the Pilot
FIXED,
E-HICH power control policy for Enumeration of DPCH or F-
RNC_BASED, None
service radio link set Type DPCH),
FOLLOW_TPC
FOLLOW_TPC
(Dynamic transmit
power control
based on the TPC
of DPCH or F-
DPCH)

Whether to set the E-HICH power

Enumeration
control parameters for non-service NO, YES NO, YES None
Type
radio link set or not

This parameter specifies the power

offset of the E-HICH non-serving -35~15 dB, step: 0.1
Interval Type -350~150 dB
RLS from the power of the dB
Common Pilot Channel.
E-HICH Power Offset for Service
Radio Links Set; an offset is added
to the power of the current 2 ms
sub-frame based on the TPC field -32~31.75 dB, step:
Interval Type 0~255 dB
power of its corresponding 0.25 dB
DPCCH. This offset is related to
the Signal-to-Noise Ratio
difference.

FIXED (Fixed
transmit power),
RNC_BASED
(Dynamic transmit
power control
based on the Pilot
FIXED,
E-RGCH power control policy for Enumeration of DPCH or F-
RNC_BASED, None
service radio link set Type DPCH),
FOLLOW_TPC
FOLLOW_TPC
(Dynamic transmit
power control
based on the TPC
of DPCH or F-
DPCH)
Whether to set the E-RGCH power
Enumeration
control parameters for non-service NO, YES NO, YES None
Type
radio links or not

This parameter specifies the power

offset of the E-RGCH non-serving -35~15 dB, step: 0.1
Interval Type -350~150 dB
RL from the power of the Common dB
Pilot Channel.
E-RGCH Power Offset for Service
Radio Links Set; an offset is added
to the power of the current 2 ms
sub-frame based on the TPC field -32~31.75 dB, step:
Interval Type 0~255 dB
power of its corresponding 0.25 dB
DPCCH. This offset is related to
the Signal-to-Noise Ratio
difference.

A string of up to 64
Serial Number String Type None None
characters

A string of up to 17
Antenna Serial No. String Type None None
bytes

Unicast address in
IP Address of the FTP Server IP Address Type None 0.0.0.1~255.255.255. None
254

Source FACH Channel ID Interval Type 0~255 0~255 None

 UNSHIELDED(Not
Enumeration Shielded), UNSHIELDED,
Shield Flag to Be Set None
Type SHIELDED(Shielde SHIELDED
d)

RestartTimer. Timer for Configure-

Request or Terminate-Request Interval Type 1~65535 1~65535 ms
packets.

E-HICH Power for Single Radio -35~15 dB, step: 0.1

Interval Type -350~150 dB
Link dB

IP address bearing traffic at the 0.0.0.0~255.255.255.

IP Address Type - None
RNC. 255

Start Date Mode of the Daylight Enumeration DATE, WEEK, DATE, WEEK,
None
Saving Time Type DATEWEEK DATEWEEK

EPF (Enhanced
Proportional
Fairness), PF
Enumeration EPF, PF, RR,
Scheduling Method of HSDPA (Proportional None
Type MAXCI
Fairness), RR
(Round Robin),
MAXCI (Max C/I)
 JAN(January),
FEB(February),
MAR(March),
APR(April),
MAY(May), JAN, FEB, MAR,
Start Month of the Daylight Saving Enumeration JUN(June), APR, MAY, JUN,
None
Time Type JUL(July), JUL, AUG, SEP,
AUG(August), OCT, NOV, DEC
SEP(September),
OCT(October),
NOV(November),
DEC(December)

Slot No. Interval Type 0~7, 16, 18~19 0~7, 16, 18~19 None
Slot No. Range Type 0~7 0~7 None

Slot No. Range Type 0~7 0~7 None

Slot No. of Power Amplifier1:Power
Amplifier refers to the power Interval Type 0 0 None
amplify unit in RRU.

Slot No. of Power Amplifier2:Power

Amplifier refers to the power Interval Type 0 0 None
amplify unit in RRU.

Slot No. of RRU Begin Interval Type 0 0 None

Slot No. of RRU End Interval Type 0 0 None

Slot No. of DL Process Unit 1 Interval Type 0~3 0~3 None

Slot No. of UL Process Unit 1 Interval Type 0~3 0~3 None

Slot No. of DL Process Unit 2 Interval Type 0~3 0~3 None

Slot No. of UL Process Unit 2 Interval Type 0~3 0~3 None

Slot No. of DL Process Unit 3 Interval Type 0~3 0~3 None

Slot No. of UL Process Unit 3 Interval Type 0~3 0~3 None

Slot No. of DL Process Unit 4 Interval Type 0~3 0~3 None

Slot No. of UL Process Unit 4 Interval Type 0~3 0~3 None

Sensor Output Lower Limit of the

0~4294967.295,
NEMU Standby Analog Value Input Any Type 0~4294967295 V
precision:0.001
Parameters (Voltage Sensor)
Sensor Output Lower Limit of the
0~4294967.295,
NEMU Standby Analog Value Input Any Type 0~4294967295 A
precision:0.001
Parameters (Current Sensor)

Sensor Output Upper Limit of the

0~4294967.295,
NEMU Standby Analog Value Input Any Type 0~4294967295 V
precision:0.001
Parameters (Voltage Sensor)

Sensor Output Upper Limit of the

NEMU Standby Analog Value 0~4294967.295,
Any Type 0~4294967295 A
Input Parameters(For Current precision:0.001
Sensor)

Synchronization Period of the

Interval Type 1~525600 1~525600 min
SNTP Client Parameters

Resource Group ID Interval Type 0~3 0~3 None

250 (250km/h),
Speed Rate of High Speed Local Enumeration
400 (400km/h), 250, 400, 500 km/h
Cell Type
500 (500km/h)
 Enumeration
State of the Supported Firewall No, Yes No, Yes None
Type

Source Port No. Range Type 0~7 0~7 None

Source Fraatm Link No. Range Type 0~7 0~7 None

Source Port No. Range Type 0~7 0~7 None

 IMA(Bearing Port
Type is IMA),
UNI(Bearing Port
Enumeration
Source Port Type Type is UNI), IMA, UNI, FRAATM None
Type
FRAATM(Bearing
Port Type is
FRAATM)

Expected Rx Switch, if it is empty,

Enumeration DISABLE(Disable),
the Rx Expected Trace Byte DISABL, ENABLE None
Type ENABLE(Enable)
Setting will not be changed.

Enumeration BASE_BOARD(ba
Source Subboard Type BASE_BOARD None
Type se board)

E1_COVERBOAR
Enumeration
Source Subboard Type D(E1/T1 cover E1_COVERBOARD None
Type
board)

Source Slot No. Range Type 0~7 0~7 None

Source Slot No. Range Type 0~7 0~7 None

Source Subrack No. Range Type 0 0 None

NEXTHOP(IP
Enumeration
Route type option address of the next NEXTHOP, IF None
Type
hop), IF(Out port)
 Enumeration
Rate unit KBIT/S, CELL/S KBIT/S, CELL/S None
Type

Rx Bandwidth. This is an important

parameter for the flow control
algorithm. The value of RXBW
must be equal to the DL bandwidth Interval Type 8~100000 8~100000 kbit/s
at the RNC. If not, the result of
flow control algorithm will be
affected.

E-HICH Power Offset for Single -32~31.75 dB, step:

Interval Type 0~255 dB
Radio Link 0.25 dB

Subrack No. Interval Type 0~8, 20~254 0~8, 20~254 None

Subrack No. Range Type 0 0 None

Subrack No. Range Type 0 0 None

Subrack No. of Power Amplifier1:
Power Amplifier refers to the power Interval Type 20~254 20~254 None
amplify unit in RRU.

Subrack No. of Power Amplifier2:

Power Amplifier refers to the power Interval Type 20~254 20~254 None
amplify unit in RRU.

Subrack No. of RRU Begin Interval Type 20~254 20~254 None

Subrack No. of RRU End Interval Type 20~254 20~254 None

Subrack No. of DL Process Unit 1 Interval Type 0 0 None

Subrack No. of UL Process Unit 1 Range Type 0 0 None

Subrack No. of DL Process Unit 2 Interval Type 0 0 None

Subrack No. of UL Process Unit 2 Range Type 0 0 None

Subrack No. of DL Process Unit 3 Interval Type 0 0 None

Subrack No. of UL Process Unit 3 Range Type 0 0 None

Subrack No. of DL Process Unit 4 Interval Type 0 0 None

Subrack No. of UL Process Unit 4 Range Type 0 0 None

FAN (Fan
Subrack), EXT
Enumeration
Subrack Type (Extension FAN, EXT, RFU None
Type
Subrack), RFU
(RFU Subrack)
 TRACE_1BYTE(O
ne byte type),
TRACE_1BYTE,
Enumeration TRACE_16BYTE(1
Expected Rx Type TRACE_16BYTE, None
Type 6 byte CRC type),
TRACE_64BYTE
TRACE_64BYTE(6
4 Byte type)

Expected Rx Information Any Type 0~64 characters 0~64 characters None

Expected Rx Procotol Version.

According to the Second Revision
of ITU-T 3/G.831, the trace
REVISION_2ND(S
message will be padded with T.50
econd Revision.
"NUL" character to get a maximum
Padding with T.50
available byte character string. For
Enumeration "NUL"), REVISION_2ND,
interworking with equipment None
Type EARLIER_VER(Pri EARLIER_VER
developed prior to this version of
or to Second
protocol that may use the T.50
Revision. Padding
space as a padding character, new
with T.50 space)
equipment should be able to
generate T.50 "SPACE" padding
characters as an option.

SAAL Link No. Interval Type 0~63 0~63 None

The value range is The value range is

30~6759 when rate 30~6759 when rate
unit is kbps; unit is kbps; kbps
Sustain Cell Rate Interval Type The value range is The value range is or
71~15942 when 71~15942 when rate cell/s
rate unit is cell per unit is cell per
second; second;
Start Time of the Daylight Saving
Compound Type None HOUR , MIN , SEC None
Time (At a Non-DST).

Start Time of the E1/T1 Routine

Compound Type None Format:HH&MM&SS None
Test

The value range is The value range is

30~6759 when rate 30~6759 when rate
unit is kbps; unit is kbps; kbps
Sustain Cell Rate Interval Type The value range is The value range is or
71~15942 when 71~15942 when rate cell/s
rate unit is cell per unit is cell per
second; second;

It is the number of the site. Interval Type 0~4294967295 0~4294967295 None

Site Number Interval Type 0~4294967295 0~4294967295 None

A string of up to 31
Site Name String Type None None
bytes
 ENABLE(Scramble
, it must be
ENABLE, when
Enumeration
Scramble Mode E1/T1 adopts AMI ENABLE, DISABLE None
Type
mode),
DISABLE(No
scramble)

SCTP Link No. Interval Type 0~19 0~19 None

Subunit Number of the Antenna

Interval Type 1~6 1~6 None
Line Device (ALD)

ON (Need to be
Switch of the Time Synchronization Enumeration synchronized),
ON, OFF None
of the SNTP Client Parameters Type OFF (Not need to
be synchronized)
Second local IP address of SCTP
association. This parameter is one
of those between NodeB and RNC.
This parameter must meet the
following conditions:
This parameter can be set to
0.0.0.0. If it is not set to 0.0.0.0,
0.0.0.0~255.255.255.
the IP address is of legal A, B, or IP Address Type - None
255
C type, but cannot be the reserved
IP address 0.x.x.x or 127.x.x.x. If it
is set to 0.0.0.0, this parameter is
not used. The parameter cannot be
equal to any other SCTP link IP
address but must be an active
interface address of this board.

SUN(Sunday),
MON(Monday),
TUE(Tuesday), SUN, MON, TUE,
Start Week of the Daylight Saving Enumeration
WED(Wednesday), WED, THU, FRI, None
Time Type
THU(Thursday), SAT
FRI(Friday),
SAT(Saturday)
Second peer IP address of SCTP
association. This parameter is one
of those between NodeB and RNC.
This parameter must be set to
meet the following conditions:
This parameter can be set to
0.0.0.0. If it is not set to 0.0.0.0, 0.0.0.0~255.255.255.
IP Address Type - None
the IP address is of legal A, B, or 255
C type, but cannot be the reserved
IP address 0.x.x.x or 127.x.x.x. If it
is set to 0.0.0.0, this parameter is
not used. The parameter cannot be
equal to any other SCTP link IP
address.

Automatic Alarm Handling Switch Enumeration ON (Switch on),

ON, OFF None
After the VSWR Alarm Type OFF (Switch off)

Smooth Power Change Function Enumeration OPEN (OPEN),

OPEN, CLOSE None
Switch Type CLOSE (CLOSE)

FIRST(First),
SECOND(Second), FIRST, SECOND,
Start Week Sequence of the Enumeration
THIRD(Third), THIRD, FOURTH, None
Daylight Saving Time Type
FOURTH(Fourth), LAST
LAST(Last)

IPCLK Server IP Address, which

should belong to legal A, B, or C
0.0.0.0~255.255.255.
type but cannot be the reserved IP IP Address Type - None
255
address 0.x.x.x or 127.x.x.x. The
CIP and SIP should be different.

Temperature Compensation Celsi

Interval Type 0~500 0~500
Coefficient us

Number of the Tail Cabinet in the Enumeration MASTER(Master

MASTER None
RRU Ring Type cabinet)

Source Resource Group ID Interval Type 0~3 0~3 None

Timely Discharge Test Time Interval Type 30~240 30~240 d

 -100~300*0.1, degre
Antenna Tilt Interval Type -100~300
Step:0.1 e

degre
Installed Mechanical Tilt Range Type -100~127 -10~12.7, Step:0.1
e

degre
Installed Mechanical Tilt Range Type -10~30 -100~300, Step:10
e
 A map of the
timeslot, denoted in
binary format. If a
timeslot is selected,
it is crossed to the
timeslot with the
TS1, TS2, TS3, same No. of E1 0. Or
TS4, TS5, TS6, else, it is not
TS7, TS8, TS9, crossed. Select
TS10, TS11, "SELECT ALL" or
Source E1/T1 Time Slot No. A map TS12, TS13, "CLEAR ALL" to
of the timeslot, denoted in binary TS14, TS15, select or not select
format. Enumeration TS16, TS17, all the timeslots. In
None
If a timeslot is selected, it is Type TS18, TS19, E1 mode,
crossed to the timeslot. Otherwise, TS20, TS21, TS1~TS31
it is not crossed. TS22, TS23, respectively
TS24, TS25, corresponds to
TS26, TS27, timeslots 1~31.
TS28, TS29, Timeslots 0 cannot
TS30, TS31 be configured. In T1
mode, TS1~TS24
respectively
corresponds to
timeslots 1~24, and
the other timeslots
are unavailable.

Source Port VCI Interval Type 32~511 32~511 None

Source Port VPI Interval Type 0~255 0~255 None

Celsi
Temperature Alarm Lower Limit Interval Type -10.00~55.00 -10.00~55.00
us
Minimum Preferable Value of the
Temperature at the Delta Air Outlet Celsi
Interval Type -99~70 -99~70
of the NCMU Heat Control Delta us
Parameter

Format:HH&MM&S
Start Time Compound Type Format:HH&MM&SS None
S

Time Offset of the Daylight Saving

Interval Type -120~120 -120~120 None
Time

TRUNK (TRUNK),
Enumeration
RRU Topology Position BRANCH TRUNK, BRANCH None
Type
(BRANCH)

Optical Port Number of the Tail

0~2(WBBPa),
Interface Board (For Ring Topology Interval Type 0~5 None
0~5(WBBPb)
Only)

RTVBR(Real Time
Service Type. When the value is Variable Bit Rate),
CBR or UBR, only PCR needs to NRTVBR(Non-Real
be set; when the value is RTVBR Time Variable Bit
Enumeration RTVBR, NRTVBR,
or NRTVBR, both PCR and SCR Rate), None
Type UBR, UBR+
need to be set; when the value is UBR(Unspecified
UBR+, both PCR and MCR need Bit Rate),
to be set. UBR_PLUS(Unspe
cified Bit Rate+)
 CBR(Constant Bit
Rate),
Bearing Service Type. When the RTVBR(Real Time
value is CBR or UBR, only PCR Variable Bit Rate),
needs to be set; when the value is NRTVBR(Non-Real CBR, RTVBR,
Enumeration
RTVBR or NRTVBR, both PCR Time Variable Bit NRTVBR, UBR, None
Type
and SCR need to be set; when the Rate), UBR+
value is UBR+, both PCR and UBR(Unspecified
MCR need to be set. Bit Rate),
UBR_PLUS(Unspe
cified Bit Rate+)

STM1 No. Range Type 0~1 0~1 None

Slot Number of the Tail Interface

Interval Type 2~3 2~3 None
Board (For Ring Topology Only)

Number of the Tail Subrack (For

Interval Type 0 0 None
Ring Topology Only)

CHAIN (Chain
Enumeration Topology Type),
Topology Type of the RRU Chain CHAIN, RING None
Type RING (Ring
Topology Type)

Celsi
Temperature Alarm Upper Limit Interval Type -10.00~55.00 -10.00~55.00
us

Sub Frame Max Length, which

indicates the maximum length of
the FP before multiplexing. The FP
Interval Type 1~1023 1~1023 byte
can be multiplexed only when its
frame length is smaller than this
value.

Tx Switch, if it is empty, the Tx

Enumeration DISABLE(Disable),
Trace Byte Setting will not be DISABLE, ENABLE None
Type ENABLE(Enable)
changed.
 Enumeration J0(J0), J1(J1),
Trace Byte J0, J1, J2 None
Type J2(J2)

This parameter indicates the

Interval Type 1~20 1~20 ms
duration of Timer.

16th TimeSlot Support. This

Enumeration ENABLE(Enable),
parameter is valid when the ENABLE, DISABLE None
Type DISABLE(Disable)
timeslot is in E1 mode.

Tx Unit No. Range Type 0~1 0~1 None

Enumeration ON (Switch on),

WRFU/RRU TX Unit Switch ON, OFF None
Type OFF (Switch off)
 A map of the
timeslot, denoted in
binary format. If a
timeslot is selected,
it is crossed to the
timeslot with the
TS1, TS2, TS3, same No. of E1 0. Or
TS4, TS5, TS6, else, it is not
TS7, TS8, TS9, crossed. Select
TS10, TS11, "SELECT ALL" or
TS12, TS13, "CLEAR ALL" to
E1/T1 Time Slot No. A map of the
TS14, TS15, select or not select
timeslot, denoted in binary format.
Enumeration TS16, TS17, all the timeslots. In
If a timeslot is selected, it is None
Type TS18, TS19, E1 mode,
crossed to the timeslot. Otherwise,
TS20, TS21, TS1~TS31
it is not crossed.
TS22, TS23, respectively
TS24, TS25, corresponds to
TS26, TS27, timeslots 1~31.
TS28, TS29, Timeslots 0 cannot
TS30, TS31 be configured. In T1
mode, TS1~TS24
respectively
corresponds to
timeslots 1~24, and
the other timeslots
are unavailable.

Tx Bandwidth Interval Type 8~100000 8~100000 kbit/s

The TXBW of RSCGRP should be
smaller than or equal to the Interval Type 32~15800 32~15800 kbit/s
physical port bandwidth.

VOLTAGE
Sensor Type of the NEMU Standby Enumeration (Voltage Type), VOLTAGE,
None
Analog Value Input Parameters Type CURRENT CURRENT
(Current Type)

Undercurrent Alarm Clearance

Threshold of the Antenna Line Interval Type 0~1000 0~1000 mA
Device (ALD)

Upper Threshold of the NEMU 57.00~60.00,

Any Type 57.00~60.00 V
Input Voltage Alarm precision:0.01
Upper Alarm Occur Limit Any Type None None None

It refers to the uplink delay of the

Interval Type 0~1000 0~1000 ns
first antenna channel.

It refers to the uplink delay of the

Interval Type 0~1000 0~1000 ns
second antenna channel.

It refers to the uplink delay of the

Interval Type 0~1000 0~1000 ns
third antenna channel.

It refers to the uplink delay of the

Interval Type 0~1000 0~1000 ns
fourth antenna channel.
UL Frequency Channel Number Interval Type 0~65535 0~65535 None

UL BB Resource Group No. Interval Type 0~3 0~3 None

UL BB Resource Group No. Interval Type 0~3 0~3 None

Tx CBS. Recommended value: 1/2

Interval Type 15000~155000000 15000~155000000 bit
of the TX bandwidth.

Tx EBS Interval Type 0~155000000 0~155000000 bit

Undercurrent Alarm Occurrence

Threshold of the Antenna Line Interval Type 0~1000 0~1000 mA
Device (ALD)

Maximum value of the timer for

Interval Type 0~255 0~255 min
disabling the cell transmitter

A string of up to 16
User name of FTP Server for login String Type None None
bytes
 TRACE_1BYTE(O
ne byte type),
TRACE_1BYTE,
Enumeration TRACE_16BYTE(1
Tx Type TRACE_16BYTE, None
Type 6 byte CRC type),
TRACE_64BYTE
TRACE_64BYTE(6
4 Byte type)

Tx Information Any Type 0~64 characters 0~64 characters None

A string of up to 64
Vendor Code String Type None None
characters
Tx Procotol Version. According to
the Second Revision of ITU-T
3/G.831, the trace message will be REVISION_2ND(S
padded with T.50 "NUL" character econd Revision.
to get a maximum available byte Padding with T.50
character string. For interworking Enumeration "NUL"), REVISION_2ND,
None
with equipment developed prior to Type EARLIER_VER(Pri EARLIER_VER
this version of protocol that may or to Second
use the T.50 space as a padding Revision. Padding
character, new equipment should with T.50 space)
be able to generate T.50 "SPACE"
padding characters as an option.

User Name. It is mandatory if

Any Type 0~64 characters 0~64 characters None
AUTH is not NONAUTH.

UNI Link No. Interval Type 0~7 0~7 None

Bearing VCI Interval Type 32~511 32~511 None

V1.0(IMA protocol
Enumeration version 1.0),
IMA Protocol Version V1.0, V1.1 None
Type V1.1(IMA protocol
version 1.1)

VLAN Group No. Interval Type 0~3 0~3 None

VLAN ID Interval Type 1~4094 1~4094 None

SINGLEVLAN
Enumeration (Single vlan), SINGLEVLAN,
VLAN Mode None
Type VLANGROUP VLANGROUP
(Vlan Group)
VLAN Priority, which indicates the
Interval Type 0~7 0~7 None
priority level of VLAN

Bearing VPI Interval Type 0~255 0~255 None

VP_SWITCH(VC
Enumeration Switch), VP_SWITCH,
Tree Link PVC Switch Type None
Type VC_SWITCH(VP VC_SWITCH
Switch)

Vertical Position of the RRU Interval Type 0~1000 0~1000 None

DEM_2_CHAN (2-
Channels
Demodulation
Mode),
DEM_4_CHAN (4-
DEM_2_CHAN,
Channels
Enumeration DEM_4_CHAN,
Work Mode Demodulation None
Type DEM_ECON_4_CH
Mode),
AN
DEM_ECON_4_C
HAN (Economical
4-Channels
Demodulation
Mode)
 GMT-1200 (GMT- GMT-1200 (GMT-
12:00), GMT-1100 12:00), GMT-1100
(GMT-11:00), (GMT-11:00), GMT-
GMT-1000 (GMT- 1000 (GMT-10:00),
10:00), GMT-0900 GMT-0900 (GMT-
(GMT-09:00), 09:00), GMT-0800
GMT-0800 (GMT- (GMT-08:00), GMT-
08:00), GMT-0700 0700 (GMT-07:00),
(GMT-07:00), GMT-0600 (GMT-
GMT-0600 (GMT- 06:00), GMT-0500
06:00), GMT-0500 (GMT-05:00), GMT-
(GMT-05:00), 0400 (GMT-04:00),
GMT-0400 (GMT- GMT-0330 (GMT-
04:00), GMT-0330 03:30), GMT-0300
(GMT-03:30), (GMT-03:00), GMT-
GMT-0300 (GMT- 0200 (GMT-02:00),
Time Zone (If it is not specified,
Enumeration 03:00), GMT-0200 GMT-0100 (GMT-
the time zone settings do not None
Type (GMT-02:00), 01:00), GMT (GMT),
change.)
GMT-0100 (GMT- GMT+0100
01:00), GMT (GMT+01:00),
(GMT), GMT+0200
GMT+0100 (GMT+02:00),
(GMT+01:00), GMT+0300
GMT+0200 (GMT+03:00),
(GMT+02:00), GMT+0330
GMT+0300 (GMT+03:30),
(GMT+03:00), GMT+0400
GMT+0330 (GMT+04:00),
(GMT+03:30), GMT+0430
GMT+0400 (GMT+04:30),
(GMT+04:00), GMT+0500
GMT+0430 (GMT+05:00),
(GMT+04:30), GMT+0530
GMT+0500 (GMT+05:30),

Switch for disturb detect range 0~1 0~1 None

Check mode range 0~2 0~2 None

If the check mode

If the check mode is
is POW_IQ_MODE
POW_IQ_MODE or
or IQ_MODE, the
IQ_MODE, the range
range is 9~28.If the
IQ Data Length range is 2^9~2^28.If the byte
check mode is
check mode is
POW_MODE, the
POW_MODE, 255
range is 0xFF for
for invalid value.
invalid value.
 If the check mode If the check mode is
is POW_IQ_MODE POW_IQ_MODE or
or POW_MODE, POW_MODE, the
the range is 9~18.If range is 9~18, If the
Power Start Period range None
the check mode is check mode is
IQ_MODE, the IQ_MODE, the range
range is 0xFF for is 0xFF for invalid
invalid value. value.

0.1se
Power Collect Time range 5~50 0.5s~5s
c

Detect Period range 100~5000 0.1s~5s ms

When the signal linearity range is

bigger than the threshold, the range 0~4294967295 0~4294967295 dBFS
detect is started.

Unit Number Enumerate 1~8, 0xFF for all 1~8, 0xFF for all None

Carrier Index 1 range 0~3 0~3 None

Unit Index 1 range 0~1 0~1 None

Carrier Index 2 range 0~3 0~3 None

Unit Index 2 range 0~1 0~1 None

Carrier Index 3 range 0~3 0~3 None

Unit Index 3 range 0~1 0~1 None

Carrier Index 4 range 0~3 0~3 None

Unit Index 4 range 0~1 0~1 None

Carrier Index 5 range 0~3 0~3 None

Unit Index 5 range 0~1 0~1 None

Carrier Index 6 range 0~3 0~3 None

Unit Index 6 range 0~1 0~1 None

Carrier Index 7 range 0~3 0~3 None

Unit Index 7 range 0~1 0~1 None

Carrier Index 8 range 0~3 0~3 None

Unit Index 8 range 0~1 0~1 None

Rate Unit Enumerate kbps, cell/s kbps, cell/s None

HW_DEFINED,
Protocol Type Enumerate HW_DEFINED, PTP None
PTP

Domain which slave side join in Range Type 0~127 0~127 None

A flag indicating which RNC the

Enumerate MASTER, SLAVE MASTER, SLAVE None
NodeB belong to.

Maintenance Domain name String Type - 1~43byte None

Maintenance level Range Type 0~7 0~7 None

Maintenance Domain name String Type - 1~43byte None

Maintenance Association name String Type - 1~43byte None

Virtual LAN ID Range Type 1~4094 1~4094 None

Maintenance End Point ID, only in

Range Type 1~8191 1~8191 None
VLAN

Remote Maintenance End Point ID Range Type 1~8191 1~8191 None

Remote Maintenance End Point

String Type - 1~13 byte None
MAC address

0.0.0.0~255.255.255.
Destination IP Address IP Address Type - None
255
 Enumeration
Bearing Port Type ETH, ETHTRK ETH, ETHTRK None
Type

Port No. Range Type 0~3 0~3 None

BFD Session No. Range Type 0~3 0~3 None

0.0.0.0~255.255.255.
Source IP Address IP Address Type None None
255

0.0.0.0~255.255.255.
Destination IP Address IP Address Type None None
255

Enumeration SINGLE_HOP, SINGLE_HOP,

Hop Type None
Type MULTI_HOP MULTI_HOP

User configure local TX interval Range Type 10~1000 10~1000 ms

User configure local RX interval Range Type 10~1000 10~1000 ms

User configure local detect

Range Type 3~10 3~10 None
multiplier

TrunkNo. Range Type 0~1 0~1 None

Enumeration DISABLE,
Lacp Switch DISABLE, ENABLE None
Type ENABLE

Enumeration DISABLE,
ArpProxy DISABLE, ENABLE None
Type ENABLE

one
Frame Error Rate AppearThreshold in a
Range Type 0~100 0~100
of FE MAC Layer thous
and
one
Frame Error Rate
in a
DisappearThreshold of FE MAC Range Type 0~100 0~100
thous
Layer
and

Ethernet Port No. in TRUNK Range Type 0~3 0~3 None

Maximum Efach Retransmission Time
Range Type 0~10 0~10
Times s

Max HARQ Retransmission Times

Time
of Non-Conversational serive in Range Type 0~10 0~10
s
Cell DCH state

CQI (CQI-based
HS-SCCH Power Control Method Enumeration power control),
CQI, FIXED None
in CELL DCH state Type FIXED (Fixed
Power)

CQI (CQI-based
EFACH HS-SCCH Power Control Enumeration power control),
CQI, FIXED None
Method Type FIXED (Fixed
Power)

HS-SCCH FER Target in CELL

Range Type 1~999 1~999 ‰
DCH State

NO_CQI_ADJ(Not
CQI Adjust
NO_CQI_ADJ,
CQI Adjustment Algorithm Switch Enumeration Algorithm),
CQI_ADJ_BY_RBLE None
of Conversational Service Type CQI_ADJ_BY_RBL
R
ER(CQI Adjusted
by RBLER),

NO_CQI_ADJ(Not
CQI Adjust
NO_CQI_ADJ,
CQI Adjustment Algorithm Switch Enumeration Algorithm),
CQI_ADJ_BY_IBLE None
of non-Conversational Service Type CQI_ADJ_BY_IBL
R
ER(CQI Adjusted
by IBLER)
Residual BLER Target is valid only
when the CQI Adjust Algorithm is Range Type 1~50 1~50 ‰
set to CQI_ADJ_BY_RBLER

HSUPA CE SCHEDULING Enumeration

OPEN, CLOSE 0, 1 None
SWITCH Type

HSUPA OVERLOAD Enumeration

OPEN, CLOSE 0, 1 None
SCHEDULING SWITCH Type

It refers to Source LocalCell ID Range Type 0~26843545 0~26843545 None

It refers to Destination LocalCell ID Range Type 0~26843545 0~26843545 None

Max Sharing Power Ratio Range Type 1~80 1~80 %

Sharing Power Margin Range Type 1~80 1~80 %

Enumeration
R99 Flow Control Function Switch OPEN, CLOSE OPEN, CLOSE None
Type

INHBOARD, INHBOARD,
Enumeration
Dl BB Resource Allocation Mode UNLIMITED, UNLIMITED, None
Type
INEBOARD INEBOARD

Enumeration
BB Resource Pool Type GEN_POOL GEN_POOL None
Type

ENABLE(Enable), ENABLE(Enable),
Itel Shutdown Switch Enumerate None
DISABLE(Disable) DISABLE(Disable)

Switch for disturb detect range 0~1 0~1 None

Check mode range 0~2 0~2 None

If the check mode

If the check mode is
is POW_IQ_MODE
POW_IQ_MODE or
or IQ_MODE, the
IQ_MODE, the range
range is 9~28;If the
IQ Data Length range is 2^9~2^28;If the byte
check mode is
check mode is
POW_MODE, the
POW_MODE, 255
range is 0xFF for
for invalid value.
invalid value.
 If the check mode If the check mode is
is POW_IQ_MODE POW_IQ_MODE or
or POW_MODE, POW_MODE, the
the range is 9~18.If range is 9~18.If the
Power Start Period range None
the check mode is check mode is
IQ_MODE, the IQ_MODE, the range
range is 0xFF for is 0xFF for invalid
invalid value. value.

0.1se
Power Collecting Time range 5~50 0.5s~5s
c

Period of Detecting range 100~5000 0.1s~5s ms

When the signal linearity range is

bigger than the threshold, the range 0~4294967295 0~4294967295 dBFS
detect is started.

Unit Number Enumerate 1~8, 0xFF for all 1~8, 0xFF for all None

Carrier Index 1 range 0~3 0~3 None

Unit Index 1 range 0~1 0~1 None

Carrier Index 2 range 0~3 0~3 None

Unit Index 2 range 0~1 0~1 None

Carrier Index 3 range 0~3 0~3 None

Unit Index 3 range 0~1 0~1 None

Carrier Index 4 range 0~3 0~3 None

Unit Index 4 range 0~1 0~1 None

Carrier Index 5 range 0~3 0~3 None

Unit Index 5 range 0~1 0~1 None

Carrier Index 6 range 0~3 0~3 None

Unit Index 6 range 0~1 0~1 None

Carrier Index 7 range 0~3 0~3 None

Unit Index 7 range 0~1 0~1 None

Carrier Index 8 range 0~3 0~3 None

Unit Index 8 range 0~1 0~1 None

When SBT is
BASE_BOARD, When SBT is
choose IMA BASE_BOARD,
(IMAGRP), UNI choose IMA
(UNILNK), or (IMAGRP), UNI
FRAATM (UNILNK), or
(FRAATM) FRAATM (FRAATM)
When SBT is When SBT is
UNCHANNELLED UNCHANNELLED_
Enumeration
Bearing Port Type _COVERBARD, COVERBARD, None
Type
choose STM1 choose STM1
(Unchannelled (Unchannelled
STM1) STM1)
When SBT is When SBT is
BACK_BOARD, BACK_BOARD,
choose UNI choose UNI
(UNILNK), or (UNILNK), or
FRAATM FRAATM (FRAATM)
(FRAATM)

when SBT is
when SBT is
E1_COVERBOAR
E1_COVERBOARD:
D: PPP(PPP),
PPP(PPP),
MPGRP(MLPPPP
MPGRP(MLPPPP
GROUP) are
GROUP) are
available.
available.
when SBT is
when SBT is
ETH_COVERBOA
ETH_COVERBOAR
RD:
Enumeration D: ETH(ETHPORT),
Port Type ETH(ETHPORT), None
Type ETHTRK(Ethernet
ETHTRK(Ethernet
Trunk Group) ,
Trunk Group) ,
LOOPINT(LOOPBA
LOOPINT(LOOPB
CK INTERFACE) are
ACK INTERFACE)
available.
are available.
when SBT is
when SBT is
BACK_BOARD:
BACK_BOARD:
PPP(PPP) is
PPP(PPP) is
available.
available.
 When SBT is When SBT is
BASE_BOARD, BASE_BOARD,
choose PPP choose PPP (PPP),
(PPP), MPGRP MPGRP (MLPPP
(MLPPP Group), Group), ETH (ETH),
ETH (ETH), or or
LOOPINT(LOOPB LOOPINT(LOOPBA
ACK INTERFACE) CK INTERFACE)
When SBT is When SBT is
E1_COVERBOAR E1_COVERBOARD,
D, choose PPP choose PPP (PPP)
Enumeration (PPP) or MPGRP or MPGRP (MLPPP
Bearing Port Type None
Type (MLPPP Group) Group)
When SBT is When SBT is
ETH_COVERBOA ETH_COVERBOAR
RD, choose ETH D, choose ETH
(ETH), ETHTRK (ETH), ETHTRK
(Ethernet Trunk (Ethernet Trunk
Group), or Group), or
LOOPINT(LOOPB LOOPINT(LOOPBA
ACK INTERFACE) CK INTERFACE)
When SBT is When SBT is
BACK_BOARD, BACK_BOARD,
choose PPP(PPP) choose PPP(PPP)

E1T1~ETH: when
E1T1~ETH: when
SBT is
SBT is
BASE_BOARD;
BASE_BOARD;
STM1:when SBT is
Enumeration STM1:when SBT is
Port Type UNCHANNELLED None
Type UNCHANNELLED_
_COVERBOARD;
COVERBOARD;
E1T1: when SBT is
E1T1: when SBT is
E1_COVERBOAR
E1_COVERBOARD
D
 it is valid when
BEAR is ATM it is valid when
mode BEAR is ATM mode
Value range: IMA Value range: IMA
(Bearing Port Type (Bearing Port Type is
is IMA), UNI IMA), UNI (Bearing
Enumeration
Port Type (Bearing Port Type Port Type is UNI), None
Type
is UNI), STM1 STM1 (Bearing Port
(Bearing Port Type Type is STM1),
is STM1), FRAATM (Bearing
FRAATM (Bearing Port Type is
Port Type is FRAATM)
FRAATM)

Value range: Value range:

When the bear When the bear type
type is ATM, is ATM,
When SBT is When SBT is
BASE_BOARD, BASE_BOARD,
choose IMA choose IMA
(IMAGRP), UNI (IMAGRP), UNI
(UNILNK), or (UNILNK), or
FRAATM FRAATM (FRAATM)
(FRAATM) When SBT is
When SBT is UNCHANNELLED_
UNCHANNELLED COVERBARD,
_COVERBARD, choose STM1
choose STM1 (Unchannelled
(Unchannelled STM1)
STM1) When SBT is
Enumeration When SBT is BACK_BOARD,
Bearing Port Type None
Type BACK_BOARD, choose UNI
choose UNI (UNILNK), or
(UNILNK), or FRAATM (FRAATM)
FRAATM When the bear type
(FRAATM) is IPV4,
When the bear When SBT is
type is IPV4, BASE_BOARD,
When SBT is choose PPP (PPP),
BASE_BOARD, MPGRP (MLPPP
choose PPP Group), ETH (ETH),
(PPP), MPGRP or
(MLPPP Group), LOOPINT(LOOPBA
ETH (ETH), or CK INTERFACE)
LOOPINT(LOOPB When SBT is
ACK INTERFACE) E1_COVERBOARD,
When SBT is choose PPP (PPP)
E1_COVERBOAR or MPGRP (MLPPP
 If SN = 0~5, If SN = 0~5,
E1_COVERBOAR E1_COVERBOARD:
Enumeration D: E1 Coverboard; E1 Coverboard;
IMA Group Subboard Type None
Type If SN = 6~7, If SN = 6~7,
BASE_BOARD: BASE_BOARD:
Base Board; Base Board;

IP Packets Discard Alarm Appear

Threshold
Interval Type 0~100 0~100 None
Unit: one in a thousand

IP Packets Discard Alarm

Interval Type 0~100 0~100 None
Disappear Threshold

If SN = 0~5, If SN = 0~5,
E1_COVERBOAR E1_COVERBOARD:
Enumeration D:E1 Coverboard E1 Coverboard
ML PPP Group Subboard Type None
Type If SN = 6~7, If SN = 6~7,
BASE_BOARD: BASE_BOARD:
Base Board Base Board

E1T1 Subrack No. Range Type 0 0 None

E1T1 Slot No. Range Type 0~7 0~7 None

If SN = 0~5, If SN = 0~5,
Enumeration
E1T1 Subboard Type E1_COVERBOAR E1_COVERBOARD: None
Type
D:E1 Coverboard E1 Coverboard
0~3: When SBT is
0~3: When SBT is
BASE_BOARD;
BASE_BOARD;
0~7: When SBT is
0~7: When SBT is
E1T1 Port No. Range Type E1_COVERBOAR None
E1_COVERBOARD;
D;
0~3: When SBT is
0~3: When SBT is
BACK_BOARD.
BACK_BOARD.

Back Board Hw No. Range Type 0~7 0~7 None

NOCRC~1 NOCRC~1
Enumeration
Frame CRC CRC_16~2 CRC_16~2 None
Type
CRC_32~4 CRC_32~4

Remote Maintenance End Point ID Range Type 1~8191 1~8191 None

UNCHANNELLED
Enumeration UNCHANNELLED_
Subboard Type _COVERBOARD~ None
Type COVERBOARD~2
2
 Enumeration DISABLE,
3ah Switch DISABLE, ENABLE None
Type ENABLE

Refers to PTP
Refers to PTP
priority.
priority.
Value range:
Value range:
0~7:when
PTP Priority Range Type 0~7:when PRIRULE None
PRIRULE is
is IPPRECEDENCE,
IPPRECEDENCE,
0 ~63:when
0 ~63:when
PRIRULE is DSCP.
PRIRULE is DSCP.

Note: 0 indicates Note: 0 indicates that

that the statistics is the statistics is not
Clear Statistic Range Type not cleared and 1 cleared and 1 None
indicates that the indicates that the
statistics is cleared. statistics is cleared.

This parameter indicates the

number of the sent packets. Range Type 1~256 1~256 None

This parameter indicates the size

of the sent packet. Range Type 95~1500 95~1500 bytes

This parameter indicates the preset

timeout (unit: s). Range Type 1~65535 1~65535 s

This parameter indicates the preset

interval (unit: s). Range Type 1~60 1~60 s

ETHTRK(ETHTRK
Enumeration ), MPGRP(MLPPP ETHTRK(ETHTRK),
Bearing Port Type None
Type GROUP), MPGRP, ETH
ETH(ETH)

Enumeration APM100, APM100, APM200,

The type of power None
Type APM200, APM30 APM30
 Recommended
Default Value Impact Parameter Relationship
Value

None 20 Cell None

None 10 Cell None

None OPEN Cell None

None 25 Cell None

None 15 Cell None

None 30 Cell None

None 15 Cell None

None 10 Cell None

None None NodeB None

This parameter is valid when

None None NodeB
the operating mode is CSAT
 This parameter value must
be greater than
280 None NPMU [PARA]ACVLL[/PARA] in
[MML]SET
ACDCVLIMIT[/MML]
[PARA]ACVLL[/PARA] is
less than
180 None NPMU [PARA]ACVHL[/PARA] in
[MML]SET
ACDCVLIMIT[/MML]

None None OMCH None

500000 500000 NodeB None

None None NodeB None

It is valid when
[PARA]SCHEDULEPARA[/P
None None Cell
ARA] is YES in [MML]SET
MACEPARA[/MML].
None None NodeB None

This parameter is valid only

when the
None None NodeB [PARA]OBJN[/PARA] is set
"BRD", E1/T1(E1/T1),
E1/T1OnChannelsSubbrd.
When MODE = CUSTOM,
this parameter is valid. If the
parameter is not specified,
None None NodeB the existing binding relation
is not changed. If the original
setting of the system is 0,
the alarm ID is invalid.

This parameter is valid when

the [PARA]BEAR[/PARA]
NO None OMCH
parameter in [MML]ADD
OMCH[/MML] is set to IPV4.

MASTER MASTER Cell None

 For DBS:when
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is set
to REMOTE_SECTOR, the
value range is R0A, R0B.
For
BTS:REMOTE_SECTOR
None None(ADD SEC) Cell and LOCAL_SECTOR is
valid.When
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is set
to LOCAL_SECTOR, the
value range is N0A, N0B,
N1A, N1B, N2A, N2B, N3A,
N3B, N4A, N4B, N5A, N5B;
For DBS:when
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is set
to REMOTE_SECTOR, the
value range is R0A, R0B.
For
BTS:REMOTE_SECTOR
ANTA None Cell and LOCAL_SECTOR is
valid.When
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is set
to LOCAL_SECTOR, the
value range is N0A, N0B,
N1A, N1B, N2A, N2B, N3A,
N3B, N4A, N4B, N5A, N5B;
For DBS:When
[PARA]SECT[/PARA] is set
to REMOTE_SECTOR, the
value range is 20~254;
For
BTS:REMOTE_SECTOR
and LOCAL_SECTOR is
None None(ADD SEC) Cell
valid.When
[PARA]SECT[/PARA] is set
to LOCAL_SECTOR, the
value range is 4~5.When
[PARA]SECT[/PARA] is set
to REMOTE_SECTOR, the
value range is 20~254;

MASTER MASTER Cell None

 For DBS:when
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is set
to REMOTE_SECTOR, the
value range is R0A, R0B.
For
BTS:REMOTE_SECTOR
None None(ADD SEC) Cell and LOCAL_SECTOR is
valid.When
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is set
to LOCAL_SECTOR, the
value range is N0A, N0B,
N1A, N1B, N2A, N2B, N3A,
N3B, N4A, N4B, N5A, N5B;
For DBS:when
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is set
to REMOTE_SECTOR, the
value range is R0A, R0B.
For
BTS:REMOTE_SECTOR
ANTA None Cell and LOCAL_SECTOR is
valid.When
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is set
to LOCAL_SECTOR, the
value range is N0A, N0B,
N1A, N1B, N2A, N2B, N3A,
N3B, N4A, N4B, N5A, N5B;
For DBS:When
[PARA]SECT[/PARA] is set
to REMOTE_SECTOR, the
value range is 20~254;
For
BTS:REMOTE_SECTOR
and LOCAL_SECTOR is
None None(ADD SEC) Cell
valid.When
[PARA]SECT[/PARA] is set
to LOCAL_SECTOR, the
value range is 4~5.When
[PARA]SECT[/PARA] is set
to REMOTE_SECTOR, the
value range is 20~254;

MASTER MASTER Cell None

 For DBS:when
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is set
to REMOTE_SECTOR, the
value range is R0A, R0B.
For
BTS:REMOTE_SECTOR
None None(ADD SEC) Cell and LOCAL_SECTOR is
valid.When
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is set
to LOCAL_SECTOR, the
value range is N0A, N0B,
N1A, N1B, N2A, N2B, N3A,
N3B, N4A, N4B, N5A, N5B;
For DBS:When
[PARA]SECT[/PARA] is set
to REMOTE_SECTOR, the
value range is 20~254;
For
BTS:REMOTE_SECTOR
and LOCAL_SECTOR is
None None(ADD SEC) Cell
valid.When
[PARA]SECT[/PARA] is set
to LOCAL_SECTOR, the
value range is 4~5.When
[PARA]SECT[/PARA] is set
to REMOTE_SECTOR, the
value range is 20~254;

MASTER MASTER Cell None

For DBS:when
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is set
to REMOTE_SECTOR, the
value range is R0A, R0B.
For
BTS:REMOTE_SECTOR
None None(ADD SEC) Cell and LOCAL_SECTOR is
valid.When
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is set
to LOCAL_SECTOR, the
value range is N0A, N0B,
N1A, N1B, N2A, N2B, N3A,
N3B, N4A, N4B, N5A, N5B;
 For DBS:When
[PARA]SECT[/PARA] is set
to REMOTE_SECTOR, the
value range is 20~254;
For
BTS:REMOTE_SECTOR
and LOCAL_SECTOR is
None None(ADD SEC) Cell
valid.When
[PARA]SECT[/PARA] is set
to LOCAL_SECTOR, the
value range is 4~5.When
[PARA]SECT[/PARA] is set
to REMOTE_SECTOR, the
value range is 20~254;
This parameter is valid only
When the
[PARA]SECT[/PARA] is
REMOTE_SECTOR or
LOCAL_SECTOR.
When [PARA]WM[PARA] of
[MML]SET DEMODE[/MML]
None None Cell is set to DEM_2_CHAN,
there will be 1 or 2 antena;
When [PARA]WM[PARA] of
[MML]SET DEMODE[/MML]
is set to
DEM_4_CHAN or
DEM_ECON_4_CHAN ,
there will be 1/2/4 antena.

1.00E-05 1ENone5 NodeB None

None None NodeB None

None None NEMU None

This parameter TDSTM is

valid only when
[PARA]TDSTM[/PARA] in
None None Battery
[MML]SET BATATPA[/MML]
is set to "PERIOD" or
"PERIODPOWERCUT"

None None NodeB None

1000 1000 SAAL None

None None NodeB None

OFF None NodeB None

None None NodeB None

None None NEMU None

When [PARA]PT[/PARA] in
[MML]SET ALMPORT[/MML]
None None NodeB
is BOOL, this parameter is
valid.

This parameter is valid when

[PARA]OPESORT[/PARA] in
No No No
[MML]SET ALDDEV[/MML]
is set to DEV.

This parameter is valid when

[PARA]OPESORT[/PARA] in
No No No
[MML]SET ALDDEV[/MML]
is set to DEV.

This parameter is valid when

[PARA]OPESORT[/PARA] in
No No No
[MML]SET ALDDEV[/MML]
is set to DEV.
 This parameter is valid when
[PARA]OPESORT[/PARA] in
No No No
[MML]SET ALDDEV[/MML]
is set to DEV.

This parameter is valid when

[PARA]OPESORT[/PARA] in
No No No
[MML]SET ALDDEV[/MML]
is set to DEV.

This parameter is valid when

[PARA]OPESORT[/PARA] in
No No No
[MML]SET ALDDEV[/MML]
is set to DEV.

This parameter is valid when

in [MML]SET
ALDDEV[/MML]
None None No [PARA]OPESORT[/PARA] is
set to OPE and
[PARA]OPEVER[/PARA] is
set to V1.1.
This parameter is valid when
in [MML]SET
ALDDEV[/MML]
None None No [PARA]OPESORT[/PARA] is
set to OPE and
[PARA]OPEVER[/PARA] is
set to V2.0 or 3GPP

The value range is 30~600

when [PARA]PTYPE[/PARA]
is APM100.
The value range is 30~600
None None NodeB when [PARA]PTYPE[/PARA]
is APM200.
The value range is 5~600
when [PARA]PTYPE[/PARA]
is APM30.

60 60 NodeB None

None None NodeB None

None None NodeB None

None None NodeB None

None None NodeB None

This parameter must be

greater than
[PARA]FCVOL[/PARA] in
[MML]SET
BCFCVOLTAGE[/MML] and
56.5 56.5 NodeB
less than
[PARA]DCVHL[/PARA] in
[MML]SET
ACDCVLIMIT[/MML]-1, and
between 43.2 and 57.6.
This parameter is valid when
in [MML]SET
ALDDEV[/MML]
None None No [PARA]OPESORT[/PARA] is
set to DEV and
[PARA]DEVVER[/PARA] is
set to V1.1.
This parameter is valid when
in [MML]SET
ALDDEV[/MML]
None None No [PARA]OPESORT[/PARA] is
set to DEV and
[PARA]DEVVER[/PARA] is
set to V1.1.
This parameter is valid when
in [MML]SET
ALDDEV[/MML]
None None No [PARA]OPESORT[/PARA] is
set to DEV and
[PARA]DEVVER[/PARA] is
set to V1.1.
This parameter is valid when
in [MML]SET
ALDDEV[/MML]
None None No [PARA]OPESORT[/PARA] is
set to DEV and
[PARA]DEVVER[/PARA] is
set to V2.0_3GPP.
This parameter is valid when
in [MML]SET
ALDDEV[/MML]
None None No [PARA]OPESORT[/PARA] is
set to DEV and
[PARA]DEVVER[/PARA] is
set to V2.0_3GPP.
 This parameter is valid when
in [MML]SET
ALDDEV[/MML]
None None No [PARA]OPESORT[/PARA] is
set to DEV and
[PARA]DEVVER[/PARA] is
set to V2.0_3GPP.
This parameter is valid when
in [MML]SET
ALDDEV[/MML]
None None No [PARA]OPESORT[/PARA] is
set to DEV and
[PARA]DEVVER[/PARA] is
set to V2.0_3GPP.

1 1 NodeB None

This parameter is valid when

in [MML]ADD OMCH[/MML]
[PARA]BEAR[/PARA] is set
to IPV4 and
[PARA]BRT[/PARA] is set to
None None OMCH
YES.The
[PARA]DSTIP[/PARA] & the
[PARA]DSTMASK[/PARA]
must be equal to the
[PARA]DSTIP[/PARA].

This parameter is valid when

in [MML]ADD OMCH[/MML]
[PARA]BEAR[/PARA] is set
to IPV4 and
[PARA]BRT[/PARA] is set to
None None OMCH
YES.The
[PARA]DSTIP[/PARA] & the
[PARA]DSTMASK[/PARA]
must be equal to the
[PARA]DSTIP[/PARA].

This parameter is valid only

when the
None None NodeB
[PARA]FUNCTION[/PARA]
parameter is set to ENABLE.

This parameter is valid when

in [MML]SET
None None No ALDDEV[/MML]
[PARA]OPESORT[/PARA] is
set to OPE.

ENABLE ENABLE NodeB None

 This parameter is valid only
when [PARA]TT[/PARA] in
None None NodeB [MML]ADD
RRUCHAIN[/MML] is set to
RING.

0 None NodeB None

DISABLE None IUBCP None

None None NodeB None

 This parameter is valid only
when [PARA]TT[/PARA] in
None None NodeB [MML]ADD
RRUCHAIN[/MML] is set to
"RING"

ENABLE ENABLE NodeB None

If the value is "ENABLE",

the value of
ENABLE None NodeB [PARA]BSDV[/PARA] in
[MML]SET SDPA[/MML] is
valid.
The parameter is valid only
when the
43 None NodeB [PARA]BSDF[/PARA] in
[MML]SET SDPA[/MML] is
set to Enable.
 [PARA]FERAT[/PARA]
should be greater than or
None 10 Ethport
equal to
[PARA]FERDT[/PARA].

None None NodeB None

The parameter is valid only

when the
[PARA]SWT[/PARA] in
None None NodeB [MML]ACT
SOFTWARE[/MML] is set to
HOMOBRDSW or
HOMOBRDROM.
BTEM could be configed
when [PARA]BFLG[/PARA]
53 53 NodeB in [MML]SET
HTPROTECT[/MML] is
ENABLE

0 None NodeB None

REGULAR REGULAR NodeB None

[PARA]FERDT[/PARA]
should be smaller than or
None 8 Ethport
equal to
[PARA]FERAT[/PARA].

None None NodeB None

MASTER MASTER OMCH None

DISABLE DISABLE NodeB None

[PARA]CertChain[/PARA] is
valid while
None None NodeB [PARA]CCAEnableSta[/PAR
A]=Enable in [MML]SET
CERTFILE[/MML].
BEST_EFFORT None NodeB None

This parameter is valid only

when
COMPRESSED COMPRESSED NodeB
[PARA]CHRSW[/PARA]=ON
in [MML]SET CHRSW[/MML]

None None NodeB None

OFF OFF NodeB None

This parameter is valid only

when
ALL ALL NodeB
[PARA]CHRSW[/PARA]=ON
in [MML]SET CHRSW[/MML]

This parameter is valid only

when [PARA]TYPE[/PARA]
in [MML]STR
None None NodeB
RTWPRTTST[/MML] is set
to "CHANGE" or
"CHANGE_THRESHOLD"

None None NodeB None

This parameter is valid only

when the
[PARA]FPMUXSWITCH[/PA
RA] parameter in [MML]SET
FPMUX[/MML] is set to
ENABLE.
270 270 NodeB
The difference between
[PARA]FRAMELEN[/PARA](
Frame Max Length) and
[PARA]SUBFRAMELEN[/PA
RA](Sub Frame Max Length)
is greater than 4.

The value of this paramter

must be greater than or
15000 15000 SAAL
equal to the value of
[PARA]KATM[/PARA].
 This parameter is valid when
in [MML]ADD OMCH[/MML]
[PARA]BEAR[/PARA] is set
None None OMCH to IPV4 ,
[PARA]BRT[/PARA] is set to
YES and [PARA]RT[/PARA]
is set to IF.
This parameter is valid when
in [MML]ADD OMCH[/MML]
[PARA]BEAR[/PARA] is set
None None OMCH to IPV4 ,
[PARA]BRT[/PARA] is set to
YES and [PARA]RT[/PARA]
is set to IF.

75 None NodeB None

 This parameter is valid only
when [PARA]MODE[/PARA]
LINE LINE NodeB in [MML]SET
CLKMODE[/MML] is set to
"MANUAL"

None None NodeB None

MASTER(ADD MASTER(ADD The value and relation of
AAL2PATH) AAL2PATH) Cabinet No., Subrack
MASTER(ADD MASTER(ADD ALD) No.and Slot No.:
ALD) MASTER(ADD Cabinet No. Subrack No.
MASTER(ADD BACKE1T1) Slot No. Board type
BACKE1T1) MASTER(ADD BRD) 0 0 0~3
MASTER(ADD None(ADD WBBPa (WCDMA
BRD) CABINET) BaseBand Process unit type
None(ADD MASTER(ADD A) \WBBPb (WCDMA
CABINET) DEVIP) BaseBand Process unit type
MASTER(ADD MASTER(ADD B) \UTRP (Universal
DEVIP) FRAATM) extension TRansmission
MASTER(ADD MASTER(ADD Processing unit)
FRAATM) IMAGRP) 0 0 0~5
MASTER(ADD MASTER(ADD UTRP (Universal extension
IMAGRP) IMALNK) TRansmission Processing
MASTER(ADD MASTER(ADD unit)
NodeB
IMALNK) IP2RSCGRP) 0 0 6~7
MASTER(ADD MASTER(ADD WMPT (WCDMA Main
IP2RSCGRP) IPCLKLNK) Processing & Transmission
MASTER(ADD MASTER(ADD unit)
IPCLKLNK) IPPATH) 0 0 16 UBF
MASTER(ADD MASTER(ADD IPRT) (Universal BBU Fan unit)
IPPATH) MASTER(ADD 0 0 18~19
MASTER(ADD LNKSRC) UPEA(Universal Power and
IPRT) MASTER(ADD Environment interface unit
MASTER(ADD MPGRP) type A(-48V))
LNKSRC) MASTER(ADD \UPEB(Universal Power and
MASTER(ADD MPLNK) Environment interface unit
MPGRP) MASTER(ADD type B(24V))
MASTER(ADD NPSU) \UEIU(Universal
MPLNK) None(ADD Environment Interface Unit)
MASTER(ADD OBJALMSHLD) 0 6 0 NEMU
NPSU) MASTER(ADD (NodeB Environment
For DBS:This parameter is
valid only When the
[PARA]SECT[/PARA] is
REMOTE_SECTOR.
MASTER None Cell For BTS:This parameter is
valid When the
[PARA]SECT[/PARA] is
REMOTE_SECTOR and
LOCAL_SECTOR.
For DBS:This parameter is
valid only When the
[PARA]SECT[/PARA] is
REMOTE_SECTOR.
MASTER None Cell For BTS:This parameter is
valid When the
[PARA]SECT[/PARA] is
REMOTE_SECTOR and
LOCAL_SECTOR.
 ADD SEC:This parameter is
valid only When the
[PARA]SECT[/PARA] is
DIST_SECTOR.
ADD LOCELL:This
MASTER None Cell
parameter is valid noly When
the [PARA]SECT[/PARA] is
DIST_SECTOR, at the same
time[PARA]RRUMODE[/PAR
A] is UNSYNC.
ADD SEC:This parameter is
valid only When the
[PARA]SECT[/PARA] is
DIST_SECTOR.
ADD LOCELL:This
MASTER None Cell
parameter is valid noly When
the [PARA]SECT[/PARA] is
DIST_SECTOR, at the same
time[PARA]RRUMODE[/PAR
A] is UNSYNC.

MASTER MASTER NodeB None

MASTER MASTER NodeB None

MASTER MASTER NodeB None

MASTER MASTER NodeB None

MASTER MASTER NodeB None

MASTER MASTER NodeB None

MASTER MASTER NodeB None

MASTER MASTER NodeB None

None None NodeB None

None None NodeB None

ALL None NodeB None

 It is valid when
[PARA]AUTOSW[/PARA] is
64 None NodeB
ON in [MML]SET
EMGLICENSE[/MML].

It is valid only When

[PARA]DIVM[/PARA] in
None None Cell
[MML]ADD SEC[/MML] is
HALFFREQ.
[SET LOCALIP]
The IP address for local
maintenance, IP address of
the Ethernet port, and IP
address for remote
maintenance must be
unique.
The IP addresses of the FE
port, local maintenance
channel, and remote
maintenance channel cannot
be on the same network
segment. In addition, the
network segments of the
three types of IP address
must be exclusive of each
other.
None None NodeB
Check whether two IP
addresses are on the same
network segment by using
the following formula:
(IpValueA &
IpMaskA==IpValueB &
IpMaskB)&&(IpMaskA==IpM
askB)
Check whether two network
segments are exclusive of
each other by using the
following formulas:
1. IpMask=IpMaskA &
IpMaskB
2. IpValueA &
IpMask==IpValueB & IpMask
IP & ~mask cannot be 0
 IP & ~mask cannot be 0
IP & mask cannot be 0
IP & mask + ~mask cannot
be 0xffffffff
None None OMCH
IP & ~mask + mask cannot
be 0xffffffff
Note: "~mask" indicates the
complement on mask.

None None Cell None

[PARA]CRL[/PARA] is valid
while
None None NodeB [PARA]CRLEnableSta[/PAR
A]=Enable in [MML]SET
CERTFILE[/MML].

None None NodeB None

Auxiliary power
None None system None
CMU

DISABLE None NodeB None

This parameter is valid only

when
-10 None NodeB [PARA]CSLSDF[/PARA] in
[MML]SET SDPA[/MML] is
set to "ENABLE"

None None No involved None

None None NodeB None

None None NodeB None

None None NodeB None

It is valid when
[PARA]MANUALSW[/PARA]
None None NodeB
is ON in [MML]SET
EMGLICENSE[/MML].
It is valid when
[PARA]MANUALSW[/PARA]
None None NodeB
is ON in [MML]SET
EMGLICENSE[/MML].

2 None NCMU None

None None Cell None

None None NodeB None

None None NodeB None

None None NodeB None

None None NodeB None

This parameter must be

greater than
58 58 NPMU [PARA]BCVOL[/PARA] in
[MML]SET
BCFCVOLTAGE[/MML] + 1
 This parameter value must
be greater than
[PARA]LSDV[/PARA] in
[MML]SET SDPA[/MML],
less than
[PARA]FCVOL[/PARA] in
[MML]SET
BCFCVOLTAGE[/MML]-2
This parameter value must
be greater than
48.5 48.5 NPMU [PARA]BSDV[/PARA] in
[MML]SET SDPA[/MML]
when [PARA]LSDF[/PARA]
in [MML]SET SDPA[/MML] is
set to "Disable"
This parameter value must
be greater than 35 when
[PARA]LSDF[/PARA] and
[PARA]BSDF[/PARA] in
[MML]SET SDPA[/MML] are
both set to "Disable"

The [PARA]DDSTM[/PARA]
value must be smaller than
14 None Battery [PARA]TDSTM[/PARA]
value in [MML]SET
BATATPA[/MML].
This parameter is valid noly
When the
100(ADD LOCELL) None Cell [PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is
DIST_SECTOR.

The resource group is added

when [PARA]BEAR[/PARA]
DISABLE None OMCH
in [MML]ADD OMCH[/MML]
is set to ATM.

This parameter must be

greater than or equal to the
value of
[PARA]POLL[/PARA].
This parameter must be
2000 2000 SAAL smaller than or equal to the
value of
[PARA]IDLE[/PARA].
This parameter must be
smaller than the value of
[PARA]NRTM[/PARA].
None None NodeB None

None None NodeB None

[PARA]DEVTP[/PARA] is
valid while
None None NodeB
[PARA]OPMODE[/PARA]=S
ECTOR or OPMODE=CSAT

V1.1 V1.1 NodeB None

None None Cell None

None None NodeB None

None None NodeB None

This parameter is valid only

when the value of
None None NodeB [PARA]LM[/PARA] is set to
ONLYIPADDR or
IPADDRANDUDPPORT.
 This parameter is valid only
-(SET DESENS)
None Cell when the sector type of local
0(ADD LOCELL)
cell is not distributed sector.

This parameter is invalid

when the
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is
COMMON_MODE COMMON_MODE Cell DIST_SECTOR; HALFFREQ
is valid when
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is
REMOTE_SECTOR.
For DBS:It is valid when
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, R0B.
100(ADD SEC) 100(ADD SEC) Cell For BTS:It is valid when
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, N0A, N1A, N2A,
N3A, N4A, N5A.
For DBS:It is valid when
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, R0B.
100(ADD SEC) 100(ADD SEC) Cell For BTS:It is valid when
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, N0A, N1A, N2A,
N3A, N4A, N5A.
For DBS:It is valid when
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, R0B.
100(ADD SEC) 100(ADD SEC) Cell For BTS:It is valid when
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, N0A, N1A, N2A,
N3A, N4A, N5A.
 For DBS:It is valid when
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, R0B.
100(ADD SEC) 100(ADD SEC) Cell For BTS:It is valid when
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, N0A, N1A, N2A,
N3A, N4A, N5A.

None None Cell None

None(ADD
None NodeB None
DLGROUP)

0(ADD LOCELL) None Cell None

None None SCTP None

None None Battery None

None None Battery None

None None Battery None

None None Battery None

None None Battery None

None None Battery None

None None Battery None

None None Battery None

None None Battery None

None None Battery None

IP & ~mask cannot be 0

IP & mask cannot be 0
IP & mask + ~mask cannot
be 0xffffffff
None None NodeB
IP & ~mask + mask cannot
be 0xffffffff
Note: "~mask" indicates the
complement on mask.

None None NodeB None

This parameter is valid only

when
None None NodeB
[PARA]CHRSW[/PARA]=ON
in [MML]SET CHRSW[/MML]
 IP & ~mask cannot be 0
IP & mask cannot be 0
IP & mask + ~mask cannot
be 0xffffffff
None None OMCH
IP & ~mask + mask cannot
be 0xffffffff
Note: "~mask" indicates the
complement on mask.

4 4 SAAL None

67 67 SAAL None

25 25 SAAL None

None None Battery None

The value range is 0~1 when

[PARA]DSTPT[/PARA] is
IMA and
[PARA]DSTSBT[/PARA] is
BASE_BOARD;
The value range is 0~3 when
[PARA]DSTPT[/PARA] is
IMA and
[PARA]DSTSBT[/PARA] is
E1_COVERBOARD;
0 None NodeB
The value range is 0~3 when
[PARA]DSTPT[/PARA] is
UNI and
[PARA]DSTSBT[/PARA] is
BASE_BOARD;
The value range is 0~7 when
[PARA]DSTPT[/PARA] is
UNI and
[PARA]DSTSBT[/PARA] is
E1_COVERBOARD;
 The value range is 0~3 when
[PARA]DSTPT[/PARA] is
FRAATM and
[PARA]DSTSBT[/PARA] is
BASE_BOARD;
0 None NodeB
The value range is 0~7 when
[PARA]DSTPT[/PARA] is
FRAATM and
[PARA]DSTSBT[/PARA] is
E1_COVERBOARD;
The value range is 0~3 when
[PARA]DSTSBT[/PARA] is
BASE_BOARD;
None None NodeB
The value range is 0~7 when
[PARA]DSTSBT[/PARA] is
E1_COVERBOARD;

None None NodeB None

This parameter is valid only

when in [MML]ADD
OMCH[/MML]
None None OMCH [PARA]BEAR[/PARA] is set
to ATM and
[PARA]ST[/PARA] is set to
UBR+ .
When the value range of
None(ADD NodeB(ADD
-(ADD [PARA]DSTSN[/PARA] is
TREELNKPVC) TREELNKPVC)
TREELNKPVC) 6~7,
None(ADD NodeB(ADD
-(ADD TSCROSS) [PARA]DSTSBT[/PARA] is
TSCROSS) TSCROSS)
BASE_BOARD.
BASE_BOARD: when the
board in destination slot is
WMPT;
None(ADD NodeB(ADD
-(ADD E1_COVERBOARD:When
TREELNKPVC) TREELNKPVC)
TREELNKPVC) the board in destination slot
None(ADD NodeB(ADD
-(ADD TSCROSS) is UTRP
TSCROSS) TSCROSS)
Value range:
BASE_BOARD,
E1_COVERBOARD
None(ADD NodeB(ADD
-(ADD
TREELNKPVC) TREELNKPVC)
TREELNKPVC) None
None(ADD NodeB(ADD
-(ADD BACKE1T1)
BACKE1T1) BACKE1T1)
 The value range is 0~7 when
the value range of
[PARA]NO[/PARA] in
[MML]ADD
TSCROSS[/MML] is 0~7;
None None NodeB
The value range is 0~5 when
the value range of
[PARA]NO[/PARA] in
[MML]ADD
TSCROSS[/MML] is 8~15;

None None NodeB None

ATM None NodeB None

This parameter is valid only

when in [MML]ADD
OMCH[/MML]
[PARA]BEAR[/PARA] is set
None None OMCH to IPV4, [PARA]BRT[/PARA]
is set to YES,
[PARA]SN[/PARA] is set to 6-
7 and [PARA]RT[/PARA] is
set to NEXTHOP .

This parameter must be

15000 15000 SAAL greater than the value of
[PARA]KATM[/PARA].

The value range is 0~7 when

[PARA]PRIRULE[/PARA] is
set to IPPRECEDENCE. The
None None NodeB
value range is 0~63 when
[PARA]PRIRULE[/PARA] is
set to DSCP.

None OPEN Cell None

 It is valid when
[PARA]EAGCHPCPARA[/PA
None FIXED Cell
RA] is YES in [MML]SET
MACEPARA[/MML].

NO None Cell None

It is valid when
[PARA]EAGCHPCMOD[/PA
None -132 Cell
RA] is FIXED in [MML]SET
MACEPARA[/MML].
It is valid when
[PARA]EAGCHPCMOD[/PA
RA] is RNC_BASED,
FOLLOW_TPC,
None 142 Cell
CQI_BASED,
HSSCCH_BASED in
[MML]SET
MACEPARA[/MML].
When the
[PARA]BEAR[/PARA]
parameter in the MML
command is set to ATM , and
[PARA]ST[/PARA] parameter
in the MML command is set
None None OMCH
to RTVBR, NRTVBR, or
UBR+, the value of this
parameter should be greater
than that of
[PARA]SCR[/PARA] or
[PARA]MCR[/PARA].
 End Date and End
Time"[PARA]ED[/PARA] and
[PARA]ET[/PARA]in
[MML]STR
E1T1RTTST[/MML]" must be
later than the current date
and time. Start Date and
Start
Time"[PARA]SD[/PARA] and
None None NodeB
[PARA]ST[/PARA]in
[MML]STR
E1T1RTTST[/MML]" plus
test time must be earlier than
the End Date and End
Time"[PARA]ED[/PARA] and
[PARA]ET[/PARA]in
[MML]STR
E1T1RTTST[/MML]".

[PARA]EDAY[/PARA] is valid
while
[PARA]DST[/PARA]=YES
None None NodeB
and EM is DATEWEEK or
DATE in [MML]SET
TZ[/MML].

None None Battery None

None None NodeB None

[PARA]EM[/PARA] is valid
while
None None NodeB
[PARA]DST[/PARA]=YES in
[MML]SET TZ[/MML].

[PARA]EMONTH[/PARA] is
valid while
[PARA]DST[/PARA]=YES
None None NodeB
and [PARA]EM[/PARA] is
DATEWEEK or DATE in
[MML]SET TZ[/MML].
None None No involved None

None None Battery None

IP & ~mask cannot be 0

IP & mask cannot be 0
IP & mask + ~mask cannot
be 0xffffffff
None None OMCH
IP & ~mask + mask cannot
be 0xffffffff
Note: "~mask" indicates the
complement on mask.

IP & ~mask cannot be 0

IP & mask cannot be 0
IP & mask + ~mask cannot
be 0xffffffff
None None OMCH
IP & ~mask + mask cannot
be 0xffffffff
Note: "~mask" indicates the
complement on mask.

[PARA]ET[/PARA] is valid
while
None None NodeB
[PARA]DST[/PARA]=YES in
[MML]SET TZ[/MML].
 End Date and End
Time"[PARA]ED[/PARA] and
[PARA]ET[/PARA]in
[MML]STR
E1T1RTTST[/MML]" must be
later than the current date
and time. Start Date and
Start
Time"[PARA]SD[/PARA] and
None None NodeB
[PARA]ST[/PARA]in
[MML]STR
E1T1RTTST[/MML]" plus
test time must be earlier than
the End Date and End
Time"[PARA]ED[/PARA] and
[PARA]ET[/PARA]in
[MML]STR
E1T1RTTST[/MML]".

[PARA]EWEEK[/PARA] is
valid while
[PARA]DST[/PARA]=YES
None None NodeB
and [PARA]EM[/PARA] is
DATEWEEK or WEEK in
[MML]SET TZ[/MML].

[PARA]EWSEQ[/PARA] is
valide while
None None NodeB [PARA]DST[/PARA]=YES
and
[PARA]EM[/PARA]=WEEK.
This parameter must be less
than [PARA]BCVOL[/PARA]
in [MML]SET
BCFCVOLTAGE[/MML] and
53.5 53.5 NodeB greater than
[PARA]DCVLL[/PARA] in
[MML]SET
ACDCVLIMIT[/MML]+2, and
between 43.2 and 57.6.
This parameter is valid only
when the value of
None None NodeB
[PARA]LM[/PARA] is set to
IPADDRANDUDPPORT.
[PARA]PLRAT[/PARA]
should be greater than or
10 10 NodeB
equal to
[PARA]PLRDT[/PARA].
 [SET PLRTHRESHOLD]
This is the threshold for
clearing the packet loss
alarm. The value of this
command should not exceed
8 8 NodeB the alarm generation
threshold.
[PARA]PLRDT[/PARA]
should be smaller than or
equal to
[PARA]PLRAT[/PARA].
The value of this parameter
must be smaller than or
750 750 SAAL
equal to the value of
[PARA]KATM[/PARA].

None None NodeB None

None None NodeB None

None None NodeB None

This parameter is valid

when[PARA]BEAR[/PARA]
in [MML]ADD OMCH[/MML]
60 None OMCH is set to IPV4 and
[PARA]BRT[/PARA] in
[MML]ADD OMCH[/MML] is
set to YES.

IPPRECEDENCE None NodeB None

 The SN of the resource
group is required when
[PARA]JNRSCGRP[/PARA]
None None OMCH in [MML]ADD OMCH[/MML]
is set to ENABLE and
[PARA]BEAR[/PARA] is set
to ATM.
This parameter is valid when
in [MML]ADD OMCH[/MML]
[PARA]BEAR[/PARA] is set
IF None OMCH
to IPV4 and
[PARA]BRT[/PARA] is set to
YES .

None None NodeB None

This parameter is valid when

in [MML]ADD OMCH[/MML]
[PARA]BEAR[/PARA] is set
None None OMCH
to ATM and
[PARA]ST[/PARA] is set to
RTVBR or NRTVBR.

This parameter is valid when

in [MML]ADD
None None SAAL SAALLNK[/MML]
[PARA]ST[/PARA] is set to
RTVBR or NRTVBR.
 The value range is 0~7 when
[PARA]PRIRULE[/PARA] is
IPPRECEDENCE;
None None NodeB The value range is 0~63
when
[PARA]PRIRULE[/PARA] is
DSCP;

This parameter should be set

when [PARA]BEAR[/PARA]
None None OMCH
in [MML]ADD OMCH[/MML]
is set to ATM.

None None NodeB None

This parameter is valid when

in [MML]SET
None None No ALDDEV[/MML]
[PARA]OPESORT[/PARA] is
set to DEV.
This parameter is valid when
in [MML]SET
None None No ALDDEV[/MML]
[PARA]OPESORT[/PARA] is
set to DEV.
This parameter is valid when
in [MML]SET
None None No ALDDEV[/MML]
[PARA]OPESORT[/PARA] is
set to DEV.
This parameter is valid when
in [MML]SET
ALDDEV[/MML]
None None No [PARA]OPESORT[/PARA] is
set to DEV and
[PARA]DEVVER[/PARA] is
set to V2.0_3GPP.
None None GPS None

MASTER None NodeB None

FALSE None Cell None

For DBS:This parameter is

valid only When the
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is
REMOTE_SECTOR.
FALSE(ADD
None Cell For BTS:This parameter is
LOCELL)
valid When the
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is
REMOTE_SECTOR or
LOCAL_SECTOR
[PARA]HLL[/PARA] is less
than [PARA]HUL[/PARA]
None None No
in[MML]MOD
NEMUTHLIMIT[/MML]
The inner handover radius of
the local cell must not be
greater than
0(ADD LOCELL) None Cell
[PARA]RADIUS[/PARA]
in[MML]ADD
LOCELL[/MML].

None None NodeB None

None 0 NodeB None

0 None NodeB None

40 None NCMU None

15 None NCMU None

 10 None NCMU None

5 None NCMU None

[PARA]HLL[/PARA] is less
than [PARA]HUL[/PARA]
None None No
in[MML]MOD
NEMUTHLIMIT[/MML]

0 None NodeB None

CBR None SAAL None

This parameter is valid when

[PARA]FPMUXSWITCH[/PA
RA] in [MML]SET
FPMUX[/MML] is set to
ENABLE.
127 127 NodeB The difference between
[PARA]FRAMELEN[/PARA](
Frame Max Length) and
[PARA]SUBFRAMELEN[/PA
RA](Sub Frame Max Length)
is greater than 4.

BW_SHAPING_O
None NodeB None
NOFF_TOGGLE
None MIDDLE No involved None

4 4 NodeB None

This parameter is valid when

[PARA]FPMUXSWITCH[/PA
1 1 NodeB RA] in [MML]SET
FPMUX[/MML] is set to
ENABLE.

ENABLE None NodeB None

None None STM1 None

 This parameter should be set
when [PARA]BEAR[/PARA]
None None OMCH
in [MML]ADD OMCH[/MML]
is set to ATM.

None None NEMU None

This parameter should be set

when [PARA]BEAR[/PARA]
None None OMCH
in [MML]ADD OMCH[/MML]
is set to ATM.

This parameter is valid only

when the
None ULCIRx0.5 NodeB
[PARA]FUNCTION[/PARA]
parameter is set to ENABLE.

This parameter is valid when

in [MML]SET
None None No ALDDEV[/MML]
[PARA]OPESORT[/PARA] is
set to OPE.
This parameter is valid when
in [MML]SET
None None No ALDDEV[/MML]
[PARA]OPESORT[/PARA] is
set to OPE.
This parameter is valid only
when the
[PARA]FUNCTION[/PARA]
parameter is set to ENABLE.
The value depends on the
physical interface rate and
must be lower than the
None None NodeB
physical interface rate. When
[PARA]PT[/PARA] is set to
MPGRP, the value range is
32 to 155000 kbit/s; when
[PARA]PT[/PARA] is set to
ETH, the value range is 32
to 155000 kbit/s.
 This parameter is valid only
when the
[PARA]FUNCTION[/PARA]
parameter is set to ENABLE.
The value depends on the
physical interface rate and
ETH:100000
must be lower than the
MPGRP:31744 None NodeB
physical interface rate. When
ETHTHK:100000
[PARA]PT[/PARA] is set to
MPGRP, the value range is
32 to 155000 kbit/s; when
[PARA]PT[/PARA] is set to
ETH, the value range is 32
to 155000 kbit/s.

If the Ethernet port is an

electrical port and
[PARA]SPEED[/PARA] in
[MML]SET ETHPORT[/MML]
None None NodeB is not set to AUTO, this
parameter is valid. If the
Ethernet port is an optical
port, this parameter is set to
forced full-duplex.
This parameter is valid only
when [PARA]SW[/PARA] in
None None NodeB [MML]SET
SNTPCLTPARA[/MML] is set
to "ON".

This parameter is valid only

when
None None NodeB
[PARA]CHRSW[/PARA]=ON
in [MML]SET CHRSW[/MML]

NodeBSET
None None None
E1T1WORKMODE)

DISABLE DISABLE NodeB None

 This parameter is valid when
[PARA]MODE[/PARA] in
[MML]SET
CLKMODE[/MML] is set to
AUTO AUTO NodeB MANUAL and
[PARA]CLKSRC[/PARA] in
[MML]SET
CLKMODE[/MML] is set to
"IP"

DISABLE None NodeB None

NOLOOP NOLOOP NodeB None

NOLOOP NOLOOP NodeB None

DISABLE DISABLE NodeB None

The value range is 15~30

when
[PARA]SWTICH[/PARA] in
None None NodeB
[MML]SET
VSWRALMPARAM[/MML] is
set to ATM.
LL is less than
[PARA]UL[/PARA] in
42 42 NodeB
[MML]SET
NEMUINVLIMIT[/MML]
When [PARA]PT[/PARA] in
[MML]SET ALMPORT[/MML]
None None NodeB
is VALUE, this parameter is
valid.
NOLOOP NOLOOP NodeB None

[PARA]LNCODE[/PARA] can
be HDB3 or AMI when
None None NodeB [PARA]FRAME[/PARA] is
E1_DOUBLE_FRAME or
E1_CRC4_MULTI_FRAME.
[PARA]LNCODE[/PARA] can
be B8ZS or AMI when
[PARA]FRAME[/PARA] is
None None NodeB
T1_SUPER_FRAME or
T1_EXTENDED_SUPER_F
RAME.
It is valid when
[PARA]LM[/PARA] is not
NOLOOP in [MML]SET
NodeB(SET IPREMOTELOOP[/MML].
IPREMOTELOOP) It is valid when
E1/T1(SET [PARA]LM[/PARA] is not
1 1
E1T1LOP) NOLOOP in [MML]SET
STM1(SET E1T1LOP[/MML].
STM1LOP) It is valid when
[PARA]LM[/PARA] is not
NOLOOP in [MML]SET
STM1LOP[/MML].
 This parameter is valid only
when the value of
None None NodeB [PARA]LM[/PARA] is set to
ONLYIPADDR or
IPADDRANDUDPPORT.

ENABLE ENABLE NodeB None

If [PARA]PN[/PARA] = 0, the
value can be forced 10Mbps,
forced 100Mbps, or auto-
None None NodeB negotiated.
If [PARA]PN[/PARA] = 1, the
value can be forced
100Mbps.

This parameter is valid when

[PARA]MODE[/PARA] in
[MML]SET
CLKMODE[/MML] is set to
MANUAL ,
[PARA]CLKSRC[/PARA] in
0 0 NodeB [MML]SET
CLKMODE[/MML] is set to
"IP" and
[PARA]IPMODE[/PARA] in
[MML]SET
CLKMODE[/MML] is set to
MANUAL
This parameter is valid when
[PARA]TRAFFIC[/PARA] in
None None NodeB [MML]SET
VLANCLASS[/MML] is set to
USERDATA.

None None NodeB None

0 None NodeB None

None None Cell None

This parameter is valid when

[PARA]INSTAG[/PARA] in
1 None NodeB [MML]SET
VLANCLASS[/MML] is set to
ENABLE.
This parameter is valid when
[PARA]INSTAG[/PARA] in
0 None NodeB [MML]SET
VLANCLASS[/MML] is set to
ENABLE.

-(SET ETHPORT)
1500(ADD None NodeB None
ETHTRK)

None None Cell None

If it is "ENABLE", the
[PARA]LSDV[/PARA] in
DISABLE None NodeB
[MML]SET SDPA[/MML]
value is valid.
The parameter is valid only
when the
44 None NodeB [PARA]LSDF[/PARA] in
[MML]SET SDPA[/MML] is
set to Enable.
MLPPP Link(ADD
MPLNK)
ENABLE ENABLE None
PPP Link(ADD
PPPLNK)
0 None NCMU None

LTEM could be configed

when [PARA]LFLG[/PARA]
65 65 NodeB in [MML]SET
HTPROTECT[/MML] is
ENABLE
 [PARA]OTH[/PARA] is more
-20 None NodeB than [PARA]LTH[/PARA] in
[MML]SET THAT[/MML]

OFF None NodeB None

This parameter is valid only

when the [PARA]NT[/PARA]
None None NodeB parameter in [MML]ADD
AAL2NODE[/MML] is set to
LOCAL.
None None NodeB None

This parameter is valid only

0(ADD AAL2 Path(ADD
0(ADD AAL2PATH) when the [PARA]NT[/PARA]
AAL2PATH) AAL2PATH)
None(ADD parameter in [MML]ADD
-(ADD NodeB(ADD
AAL2ADJNODE) AAL2PATH[/MML] is set to
AAL2ADJNODE) AAL2ADJNODE)
ADJNODE.
It is valid when
[PARA]EAGCHPCMOD[/PA
RA] is CQI_BASED,
None -60 Cell
HSSCCH_BASED in
[MML]SET
MACEPARA[/MML].

MLPPP Group(ADD
MPGRP)
None None None
PPP Link(ADD
PPPLNK)

ENABLE ENABLE SCTP None

ATM None IUBCP None

It is valid when
[PARA]PWRMODE[/PARA]
None None Cell
is ABSOLUTE in [MML]MOD
RRUOFLOCELL[/MML].

IPV4 IPV4 NodeB None

ATM(SET
HSDPAFLOWCTR
None NodeB None
LPARA)
-(ADD RSCGRP)
Tree Link
PVC(ADD
10240 10240 TREELNKPVC) None
AAL2 Path(ADD
AAL2PATH)
None None NodeB None

ITC None NodeB None

It is valid when
[PARA]EAGCHPCMOD[/PA
RA] is CQI_BASED,
None -300 Cell
HSSCCH_BASED in
[MML]SET
MACEPARA[/MML].
This parameter is valid only
when in [MML]ADD
0 None IUBCP IUBCP[/MML]
[PARA]CPPT[/PARA] is set
to CCP.
It is valid when
[PARA]AUTOSW[/PARA] is
15 None NodeB
ON in [MML]SET
EMGLICENSE[/MML].
MLL is less than
[PARA]MUL[/PARA] in
None None NEMU
[MML]SET
NEMUANLGIN[/MML]

NCP None IUBCP None

None None NodeB None

None None NodeB None

MANUAL MANUAL NodeB None

None None NodeB None

This parameter is valid when

in [MML]SET
None None None ALDDEV[/MML]
[PARA]OPESORT[/PARA] is
set to DEV.
 25 25 IMA Group None

Tree Link
PVC(ADD
TREELNKPVC)
None None None
Timeslot
Cross(ADD
TSCROSS)

None None NodeB None

None None IP Path None

The [PARA]DSTIP[/PARA] &

the
None None NodeB [PARA]DSTMASK[/PARA]
must be equal to the
[PARA]DSTIP[/PARA].

This parameter value must

be greater than
None None NEMU [PARA]MLL[/PARA] in
[MML]SET
NEMUANLGIN[/MML]

The [PARA]DSTIP[/PARA] &

the
None None NodeB [PARA]DSTMASK[/PARA]
must be equal to the
[PARA]DSTIP[/PARA].
 For DBS:This parameter is
valid only When the
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is
REMOTE_SECTOR.
None None Cell For BTS:This parameter is
valid When the
[PARA]SECT[/PARA] in
[MML]ADD SEC[/MML] is
REMOTE_SECTOR or
LOCAL_SECTOR

None 100 Cell None

None None NodeB None

None None NodeB None

None None NodeB None

None None NodeB None

None None NodeB None

This parameter is valid only

when the
[PARA]JNRSCGRP[/PARA]
0 None Tree Link PVC
parameter in [MML]ADD
TREELNKPVC[/MML] is set
to ENABLE.

The number of
[PARA]DSTTSN[/PARA] and
None None Timeslot Cross
[PARA]SRCTSN[/PARA]
timeslots must be equal.

It is valid when
[PARA]VST[/PARA] is
None None Tree Link PVC
VC_SWITCH in [MML]ADD
TREELNKPVC[/MML].

None None Tree Link PVC None

MASTER MASTER IUBCP None

 This parameter is valid only
when the [PARA]PT[/PARA]
DISABLE DISABLE IP Path
parameter in [MML]ADD
IPPATH[/MML] is set to ETH.

The value range is 0~3 when

[PARA]SBT[/PARA] is set to
BASE_BOARD;
0 0 Fractional ATM
The value range is 0~7 when
[PARA]SBT[/PARA] is set to
E1_COVERBOARD;

It is valid when
[PARA]NSEHICHPCPARA[/
None FIXED Cell
PARA] is YES in [MML]SET
MACEPARA[/MML].

NO None Cell None

It is valid when
[PARA]NSEHICHPCMOD[/P
None -136 Cell
ARA] is FIXED in [MML]SET
MACEPARA[/MML].

It is valid when
[PARA]NSEHICHPCMOD[/P
None None Cell ARA] is RNC_BASED,
FOLLOW_TPC in [MML]SET
MACEPARA[/MML].
 It is valid when
[PARA]NSERGCHPCPARA[
None FIXED Cell
/PARA] is YES in [MML]SET
MACEPARA[/MML].

NO None Cell None

It is valid when
[PARA]NSERGCHPCMOD[/
None -173 Cell PARA] is FIXED in
[MML]SET
MACEPARA[/MML].

It is valid when
[PARA]NSERGCHPCMOD[/
None 105 Cell PARA] is RNC_BASED,
FOLLOW_TPC in [MML]SET
MACEPARA[/MML].

This parameter is valid only

when in [MML]ADD
IPPATH[/MML] the value of
[PARA]PT[/PARA] is set to
ETH and
[PARA]FPMUXSWITCH[/PA
270 270 IP Path RA] is set to ENABLE.
The difference between
[PARA]FRAMELEN[/PARA](
Frame Max Length) and
[PARA]SUBFRAMELEN[/PA
RA](Sub Frame Max Length)
is greater than 4.

FRAMEMODE_SD
None STM1 None
H
 9 None NCMU None

16 None NCMU None

The parameter is valid when

[PARA]AIDST[/PARA] in
None None NodeB [MML]SET
OBJALMSHLD[/MML]is set
to "ONEBYONE".
The parameter is valid when
[PARA]SN[/PARA] in
None None NodeB [MML]SET
OBJALMSHLD[/MML]is
valid.

None None NodeB None

 You must enter the
parameter when the ALD
system type
[PARA]AST[/PARA]in
[MML]SET
ALDPWRSW[/MML] is set to
None None NodeB
"CUSTOM".
Alarm Clear Threshold must
be
satisfied:UOTHD<UCTHD<O
OTHD;UOTHD<OCTHD<OO
THD

D128 D128 IMA Group None

None None NodeB None

You must enter the

parameter when the ALD
system type
[PARA]AST[/PARA]in
[MML]SET
ALDPWRSW[/MML] is set to
None None NodeB
"CUSTOM".
Alarm Clear Threshold must
be
satisfied:UOTHD<UCTHD<O
OTHD;UOTHD<OCTHD<OO
THD

DEV DEV NodeB None

V1.1 V1.1 NodeB None

NAME None NodeB None

None None Cell None

[PARA]OTH[/PARA] is more
65 None NodeB than [PARA]LTH[/PARA] in
[MML]SET THAT[/MML]
 This paramter is valid when
[PARA]RTTYPE[/PARA] in
[MML]ADD IPRT[/MML] is
set to IF.
The value range is 0~7 when
[PARA]PT[/PARA] is PPP
and [PARA]SBT[/PARA] is
BASE_BOARD;
The value range is 0~15
when [PARA]PT[/PARA] is
PPP and
0 0 NodeB [PARA]SBT[/PARA] is
E1_COVERBOARD;
The value range is 0~1 when
[PARA]PT[/PARA] is
MPGRP and
[PARA]SBT[/PARA] is
BASE_BOARD;
The value range is 0~3 when
[PARA]PT[/PARA] is
MPGRP and
[PARA]SBT[/PARA] is
E1_COVERBOARD;

This parameter is valid only

when
None None NodeB [PARA]RTTYPE[/PARA] in
[MML]ADD IPRT[/MML] is
set to IF.
The value range is 0~1 when
IMA Group(ADD [PARA]SBT[/PARA] is
IMAGRP) BASE_BOARD;
0 0
IMA Link(ADD The value range is 0~3 when
IMALNK) [PARA]SBT[/PARA] is
E1_COVERBOARD;
The value range is 0~3 when
[PARA]SBT[/PARA] is
BASE_BOARD;
0 0 IMA Link
The value range is 0~7 when
[PARA]SBT[/PARA] is
E1_COVERBOARD;
This parameter is valid only
when
[PARA]VLANMODE[/PARA]
DISABLE None NodeB
in [MML]ADD
VLANMAP[/MML] is set to
SINGLEVLAN.
 IP & ~mask cannot be 0
IP & mask cannot be 0
IP & mask + ~mask cannot
be 0xffffffff
None None NodeB
IP & ~mask + mask cannot
be 0xffffffff
Note: "~mask" indicates the
complement on mask.

MLPPP Group(ADD
MPGRP)
ENABLE ENABLE None
PPP Link(ADD
PPPLNK)

IP & ~mask cannot be 0

IP & mask cannot be 0
MLPPP Group(ADD IP & mask + ~mask cannot
MPGRP) be 0xffffffff
0.0.0.0 None
PPP Link(ADD IP & ~mask + mask cannot
PPPLNK) be 0xffffffff
Note: "~mask" indicates the
complement on mask.

AAL2 Path(ADD
AAL2PATH)
IP Path(ADD
IPPATH)
DISABLE None SAAL(ADD None
SAALLNK)
Tree Link
PVC(ADD
TREELNKPVC)

0 None NodeB None

The value range is 0~63

when [PARA]BEAR[/PARA]
0 None IUBCP
in [MML]ADD IUBCP[/MML]
is set to ATM.
 The value range is 0~19
when [PARA]BEAR[/PARA]
0 None IUBCP
in [MML]ADD IUBCP[/MML]
is set to IPV4.

0 None NodeB None

IP & ~mask cannot be 0

IP & mask cannot be 0
MLPPP Group(ADD IP & mask + ~mask cannot
MPGRP) be 0xffffffff
0.0.0.0 None
PPP Link(ADD IP & ~mask + mask cannot
PPPLNK) be 0xffffffff
Note: "~mask" indicates the
complement on mask.

This parameter is valid when

[PARA]TP[/PARA] in
None None NodeB
[MML]ADD RRU[/MML] is
set to "BRANCH"

None None NodeB None

None None SCTP None

IP & ~mask cannot be 0

IP & mask cannot be 0
IP & mask + ~mask cannot
be 0xffffffff
None None NodeB
IP & ~mask + mask cannot
be 0xffffffff
Note: "~mask" indicates the
complement on mask.

None None NodeB None

None None NodeB None

None None NodeB None

Value Range:
BTS3900:
UPEA/ UPEB:0~7
MRRU:0~6
RHUB:0~3
PRRU:0
NEMU:0~35
BTS3900A:
UPEA/UPEB:0~7
MRRU:0~6
None None NodeB
RHUB:0~3
PRRU:0
NPMU:5~7
DBS3900:
UPEA/UPEB:0~7
MRRU:0~6
RHUB:0~3
PRRU:0
NEMU:0~35
NPMU:5~7

NodeB(ADD
LNKSRC)
NodeB(ADD
DEVIP)
None(ADD LNKSRC) PPP Link(ADD
0(ADD LNKSRC)
None(ADD DEVIP) PPPLNK)
0(ADD DEVIP) The value range is 0~3 when
None(ADD PPPLNK) Fractional
0(ADD PPPLNK) [PARA]SBT[/PARA] is
None(ADD FRAATM) ATM(ADD
0(ADD FRAATM) BASE_BOARD.
None(ADD IPPATH) FRAATM)
0(ADD IPPATH) The value range is 0~7 when
None(ADD MPLNK) IP Path(ADD
0(ADD MPLNK) [PARA]SBT[/PARA] is
None(ADD OMCH) IPPATH)
0(ADD OMCH) E1_COVERBOARD.
None(ADD MLPPP Link(ADD
0(ADD SAALLNK)
SAALLNK) MPLNK)
OMCH(ADD
OMCH)
SAAL(ADD
SAALLNK)
 NodeB(SET
None(SET E1T1LOP)
0(SET E1T1LOP)
E1T1LOP) NodeB(SET
0(SET
None(SET E1T1WORKMODE)
E1T1WORKMOD The value range is 0~3 when
E1T1WORKMODE) Ethport(SET
E) [PARA]SBT[/PARA] is
None(SET ETHPORT)
0(SET ETHPORT) BASE_BOARD.
ETHPORT) NodeB(SET
0(SET The value range is 0~7 when
None(SET HSDPAFLOWCTR
HSDPAFLOWCTR [PARA]SBT[/PARA] is
HSDPAFLOWCTRL LPARA)
LPARA) E1_COVERBOARD.
PARA) NodeB(SET LR)
0(SET LR)
None(SET LR) IMA Group/UNI
0(SET SCRAM)
None(SET SCRAM) Link/Fractional
ATM(SET SCRAM)
None(ADD AAL2 Path(ADD The value range is 0~3 when
0(ADD
AAL2PATH) AAL2PATH) [PARA]SBT[/PARA] is
AAL2PATH)
None(ADD NodeB(ADD BASE_BOARD.
0(ADD
IP2RSCGRP) IP2RSCGRP) The value range is 0~7 when
IP2RSCGRP)
None(ADD NodeB(ADD [PARA]SBT[/PARA] is
0(ADD RSCGRP)
RSCGRP) RSCGRP) E1_COVERBOARD.
The value range is 0~3 when
[PARA]SBT[/PARA] is
None(ADD AAL2 Path(ADD
BASE_BOARD.
0(ADD AAL2PATH) AAL2PATH)
The value range is 0~7 when
AAL2PATH) None(ADD NodeB(ADD
[PARA]SBT[/PARA] is
0(ADD RSCGRP) RSCGRP) RSCGRP)
E1_COVERBOARD.
0(ADD SAALLNK) None(ADD SAAL(ADD
The value range is 0~3 when
SAALLNK) SAALLNK)
[PARA]SBT[/PARA] is
BACK_BOARD.
The value range is 0~3 when
[PARA]SBT[/PARA] is
BASE_BOARD.
The value range is 0~7 when
0 None OMCH [PARA]SBT[/PARA] is
E1_COVERBOARD.
The value range is 0~3 when
[PARA]SBT[/PARA] is
BACK_BOARD.
The value range is 0~3 when
[PARA]SBT[/PARA] is
NodeB(SET
BASE_BOARD.
0(SET None(SET HSDPAFLOWCTR
The value range is 0~7 when
HSDPAFLOWCTR HSDPAFLOWCTRL LPARA)
[PARA]SBT[/PARA] is
LPARA) PARA) IMA Group/UNI
E1_COVERBOARD.
0(SET SCRAM) None(SET SCRAM) Link/Fractional
The value range is 0~3 when
ATM(SET SCRAM)
[PARA]SBT[/PARA] is
BACK_BOARD.
Tree Link
PVC(ADD
1000 1000 TREELNKPVC) None
AAL2 Path(ADD
AAL2PATH)
None None NodeB None

ENABLE ENABLE MLPPP Group None

This parameter is valid when

[PARA]ST[/PARA] is set to
None None UBR+, and its value should
SAAL
be smaller than the value of
[PARA]PCR[/PARA].

This parameter is valid only

AAL2 Path(ADD
when the [PARA]ST[/PARA]
AAL2PATH)
is UBR+, and the value of
None None Tree Link
this parameter is smaller
PVC(ADD
than the [PARA]PCR[/PARA]
TREELNKPVC)
value.

The value range is 1~4 when

[PARA]SBT[/PARA] is
BASE_BOARD;
1 1 IMA Group
The value range is 1~8 when
[PARA]SBT[/PARA] is
E1_COVERBOARD;

The value of this parameter

100 100 MLPPP Group cannot be smaller than that
of [PARA]MPDADT[/PARA].

None None NodeB None

None None NodeB None

 when the ALD system type
[PARA]AST[/PARA] in
[MML]SET
ALDPWRSW[/MML] is set to
"custom", the value range is
between R0A, R0B and
RET_PORT;
when the ALD system type
[PARA]AST[/PARA] in
[MML]SET
ALDPWRSWALD[/MML] is
set to
"RET_ONLY_MULTICORE",
the value range is only
RET_PORT;
None None NodeB
otherwise the value range is
between R0A and R0B.
For the WRFU subrack, the
value range is between N0A
and N5A, N0B and N5B.
For the RRU, if the ALD
system type is custom, the
value range is between R0A,
R0B and RET_PORT, if the
ALD system type is
RET_ONLY_MULTICORE,
the value range is only
RET_PORT, otherwise the
value range is between R0A
and R0B.

None None NodeB None

When MODE = CUSTOM,

this parameter is valid. If the
None None NodeB parameter is not specified,
the existing type is not
changed.
[PARA]PTYPE[/PARA] is
valid while
APM100 None NodeB [PARA]CS[/PARA]=CONFIG
ED in [MML]SET
PWRSYSCFG[/MML]

None None NodeB None

The value of this parameter

50 50 MLPPP Group cannot be greater than that
of [PARA]MPDAAT[/PARA].
 [PARA]PWD[/PARA] is valid
while
None None NodeB [PARA]PKPEnableSta[/PAR
A]=Enable in [MML]SET
CERTFILE[/MML].

This parameter is valid only

when
None None NodeB
[PARA]CHRSW[/PARA]=ON
in [MML]SET CHRSW[/MML]

None 5 Cell None

This para is valid for

ABSOLUTE ABSOLUTE Cell
distribution cell.
None None NodeB None

29000(ADD
None Cell None
LOCELL)

None None NodeB None

The value range is 0~1 when

MLPPP Group(ADD [PARA]SBT[/PARA] is
MPGRP) BASE_BOARD;
0 0
MLPPP Link(ADD The value range is 0~3 when
MPLNK) [PARA]SBT[/PARA] is
E1_COVERBOARD;
None None NodeB None

None None NodeB None

MLPPP Link(ADD
MPLNK)
1500 1500 None
PPP Link(ADD
PPPLNK)

DUAL DUAL NodeB None

0 None NodeB None

None None Cell None

None None NodeB None

It is valid when
[PARA]RMTCM[/PARA] is
None None Cell
TRUE in [MML]ADD
LOCELL[/MML].

FALSE None Cell None

RruName None NodeB None

MLPPP Group(ADD
MPGRP)
DISABLE DISABLE None
PPP Link(ADD
PPPLNK)

None None NodeB None

 This parameter is valid noly
When the
SYNC(ADD
None Cell [PARA]SECT[/PARA] in
LOCELL)
[MML]ADD SEC[/MML] is
DIST_SECTOR.

UO UO NodeB None

None CODE_PRI Cell None

This parameter is valid when

[PARA]RTTYPE[/PARA] in
None None NodeB
[MML]ADD IPRT[/MML] is
set to NEXTHOP.

None None NodeB None

None OPEN Cell None

This parameter is valid only

when
[PARA]RSTMODE[/PARA] in
None None NodeB
[MML]SET
CFGFILEENB[/MML] is set
to "ENABLE".
 The value range of
[PARA]SRCSN[/PARA] is
0~7 when [PARA]NO[/PARA]
is 0~7.
None None Timeslot Cross
The value range of
[PARA]SRCSN[/PARA] is
0~5 when [PARA]NO[/PARA]
is 8~15.

None None Tree Link PVC None

Value Range:
BTS3900&BTS3900A:
MRRU, RHUB, PRRU ,
None None NodeB
WRFU
DBS3900:
MRRU, RHUB , PRRU

None None IP Path None

None None NodeB None

The LOCAL node must

None None NodeB already exist before the HUB
node is added.

PERFFIRST None NodeB None

None None AAL2 Path None

None None NodeB None

 0 None NodeB None

ON None NodeB None

DISABLE DISABLE IP Path None

None None IP Path None

None None AAL2 Path None

When the [PARA]ST[/PARA]

parameter in the MML
command is set to RTVBR,
NRTVBR, or UBR+, the
None None SAAL
value of this parameter
should be greater than that
of [PARA]SCR[/PARA] or
[PARA]MCR[/PARA].

None None NodeB None

This parameter is valid only

when [PARA]SBS[/PARA] in
None None NodeB
[MML]SET SUBBRD[/MML]
is set to "YES".
 NodeB(ADD
LNKSRC)
NodeB(ADD
DEVIP)
PPP Link(ADD
None(ADD LNKSRC)
PPPLNK)
None(ADD DEVIP)
AAL2 Path(ADD
-(ADD LNKSRC) None(ADD PPPLNK)
AAL2PATH)
-(ADD DEVIP) None(ADD
Fractional
-(ADD PPPLNK) AAL2PATH)
ATM(ADD
-(ADD AAL2PATH) None(ADD FRAATM)
FRAATM)
-(ADD FRAATM) None(ADD IMAGRP)
IMA Group(ADD
-(ADD IMAGRP) None(ADD IMALNK)
IMAGRP)
-(ADD IMALNK) None(ADD
IMA Link(ADD
-(ADD IP2RSCGRP) When [PARA]SN[/PARA] is
IMALNK)
IP2RSCGRP) None(ADD IPPATH) in the range of 0~5, choose
NodeB(ADD
-(ADD IPPATH) None(ADD IPRT) E1_COVERBOARD.
IP2RSCGRP)
-(ADD IPRT) None(ADD MPGRP) When [PARA]SN[/PARA] is
IP Path(ADD
-(ADD MPGRP) None(ADD MPLNK) in range of 6~7, choose
IPPATH)
-(ADD MPLNK) None(ADD OMCH) BASE_BOARD,
NodeB(ADD IPRT)
-(ADD OMCH) None(ADD BACK_BOARD
MLPPP Group(ADD
-(ADD RSCGRP) RSCGRP)
MPGRP)
-(ADD SAALLNK) None(ADD
MLPPP Link(ADD
-(ADD UNILNK) SAALLNK)
MPLNK)
-(ADD CFMMEP) None(ADD UNILNK)
OMCH(ADD
-(ADD ETHTRK) None(ADD
OMCH)
-(ADD CFMMEP)
NodeB(ADD
ETHTRKLNK) None(ADD ETHTRK)
RSCGRP)
None(ADD
SAAL(ADD
ETHTRKLNK)
SAALLNK)
UNI Link(ADD
UNILNK)
ETH OAM(ADD
CFMMEP)
NodeB(SET
When [PARA]SN[/PARA] is
-(SET None(SET E1T1WORKMODE)
in the range of 0~5, choose
E1T1WORKMOD E1T1WORKMODE) Ethport(SET
E1_COVERBOARD.
E) None(SET ETHPORT)
When [PARA]SN[/PARA] is
-(SET ETHPORT) ETHPORT) NodeB(SET LR)
in range of 6~7, choose
-(SET LR) None(SET LR) IMA Group/UNI
BASE_BOARD,
-(SET SCRAM) None(SET SCRAM) Link/Fractional
BACK_BOARD
ATM(SET SCRAM)
When [PARA]SN[/PARA] is
in the range of 0~5, choose
E1_COVERBOARD.
None None NodeB When [PARA]SN[/PARA] is
in range of 6~7, choose
BASE_BOARD,
BACK_BOARD
 It is valid when
[PARA]SCCHPWRCM[/PAR
None 28 Cell
A] is FIXED in [MML]SET
MACHSPARA[/MML].

NO None Cell None

None(ADD
None Cell None
CMBGROUP)

When the [PARA]ST[/PARA]

parameter in the MML
AAL2 Path(ADD
command is set to RTVBR,
AAL2PATH)
NRTVBR, or UBR+, the
None None Tree Link
value of this parameter
PVC(ADD
should be greater than that
TREELNKPVC)
of [PARA]SCR[/PARA] or
[PARA]MCR[/PARA].

None(ADD SCTP(ADD
SCTPLNK) SCTPLNK)
0.0.0.0(ADD PPP Link(ADD
None None
PPPLNK) PPPLNK)
0.0.0.0(ADD MLPPP Group(ADD
MPGRP) MPGRP)

None None SCTP None

MLPPP Link(ADD
MPLNK)
ENABLE ENABLE None
PPP Link(ADD
PPPLNK)
The value range is 0~7 when
MLPPP Link(ADD [PARA]SBT[/PARA] is
MPLNK) BASE_BOARD;
0 None
PPP Link(ADD The value range is 0~15
PPPLNK) when [PARA]SBT[/PARA] is
E1_COVERBOARD;

60 None NodeB None

None None NodeB None

 [PARA]SDAY[/PARA] is valid
while
[PARA]DST[/PARA]=YES
None None NodeB
and [PARA]SM[/PARA] is
DATEWEEK or DATE in
[MML]SET TZ[/MML].

None None Battery None

None None Battery None

MLPPP Group(ADD
This parameter is mandatory
MPGRP)
None None if [PARA]AUTH[/PARA] is
PPP Link(ADD
not NONAUTH.
PPPLNK)
For BTS:When the value of
[PARA]SECT[/PARA] is
None None Cell
LOCAL_SECTOR, It's valua
is 0~5.
This parameter is valid when
None None NodeB the operating mode is
SECTOR.

None None AAL2 Path None

For BTS, The para

LOCAL_SECTOR of
[MML]ADD SEC[/MML] is
valid and optional, When
[PARA]SECT[/PARA] is
REMOTE_SECTO REMOTE_SECTOR(
LOCAL_SECTOR, It's value
R(ADD SEC) ADD SEC) Cell
should be 4 or 5.
-(ADD LOCELL) None(ADD LOCELL)
For DBS, When
[PARA]SECT[/PARA] is
REMOTE_SECTOR, It's
value should be ROA and
R0B
This parameter is valid when
in [MML]SET
ALDDEV[/MML]
None None No [PARA]OPESORT[/PARA] is
set to OPE and
[PARA]OPEVER[/PARA] is
set to V1.1.
 This parameter is valid when
in [MML]SET
ALDDEV[/MML]
None None No [PARA]OPESORT[/PARA] is
set to OPE and
[PARA]OPEVER[/PARA] is
set to V2.0_3GPP.

It is valid when
[PARA]SEHICHPCPARA[/P
None FIXED Cell
ARA] is YES in [MML]SET
MACEPARA[/MML].

NO None Cell None

It is valid when
[PARA]SEHICHPCMOD[/PA
None -197 Cell
RA] is FIXED in [MML]SET
MACEPARA[/MML].

It is valid when
[PARA]SEHICHPCMOD[/PA
None 96 Cell RA] is RNC_BASED,
FOLLOW_TPC in [MML]SET
MACEPARA[/MML].

It is valid when
[PARA]SERGCHPCPARA[/P
None FIXED Cell
ARA] is YES in [MML]SET
MACEPARA[/MML].
NO None Cell None

It is valid when
[PARA]SERGCHPCMOD[/P
None -210 Cell
ARA] is FIXED in [MML]SET
MACEPARA[/MML].

It is valid when
[PARA]SERGCHPCMOD[/P
None 100 Cell ARA] is RNC_BASED,
FOLLOW_TPC in [MML]SET
MACEPARA[/MML].

None None NodeB None

This parameter is valid when

in [MML]SET
None None No ALDDEV[/MML]
[PARA]DEVVER[/PARA] is
set to DEV .

None None NodeB None

None(ADD
None NodeB None
CMBGROUP)
None None NodeB None

MLPPP Link(ADD
MPLNK)
3000 3000 None
PPP Link(ADD
PPPLNK)
It is valid when
[PARA]SEHICHPCMOD[/PA
None -243 Cell
RA] is FIXED in [MML]SET
MACEPARA[/MML].

None None IP Path None

[PARA]SM[/PARA] is valid
while
None None NodeB
[PARA]DST[/PARA]=YES in
[MML]SET TZ[/MML].

None EPF Cell None

 [PARA]SMONTH[/PARA] is
valid while
[PARA]DST[/PARA]=YES
None None NodeB
and [PARA]SM[/PARA] is
DATEWEEK or DATE in
[MML]SET TZ[/MML].

Cabinet No. Subrack No.

Slot No. Board type
0 0 0~3 WBBPa
(WCDMA BaseBand
Process unit type A)
\WBBPb (WCDMA
BaseBand Process unit type
B) \UTRP (Universal
extension TRansmission
Processing unit)
0 0 0~5 UTRP (Universal
extension TRansmission
Processing unit)
0 0 6~7 WMPT
(WCDMA Main Processing &
Transmission unit)
0 0 16 UBF (Universal
None None NodeB
BBU Fan unit)
0 0 18~19
UPEA(Universal Power and
Environment interface unit
type A(-48V))
\UPEB(Universal Power and
Environment interface unit
type B(24V))
\UEIU(Universal
Environment Interface Unit)
0 4 0~5 WRFU (WCDMA
Radio Frequency Unit)
0 6 0 NEMU (NodeB
Environment Monitoring Unit)
0 7 0 NPMU (NodeB
Power Monitoring Unit)
0 11 0 NFAN (NodeB
None(ADD ADD
LNKSRC) None(ADD LNKSRC) LNKSRC(Optional)
None(ADD DEVIP) None(ADD DEVIP) ADD
None(ADD None(ADD PPPLNK) DEVIP(Optional)
PPPLNK) None(ADD ADD
None(ADD AAL2PATH) PPPLNK(Optional)
AAL2PATH) None(ADD FRAATM) ADD
None(ADD None(ADD IMAGRP) AAL2PATH(Option
FRAATM) None(ADD IMALNK) al)
None(ADD None(ADD ADD
IMAGRP) IP2RSCGRP) FRAATM(Optional)
None(ADD None(ADD ADD
IMALNK) IPCLKLNK) IMAGRP(Optional)
None(ADD None(ADD IPPATH) ADD
IP2RSCGRP) None(ADD IPRT) IMALNK(Optional)
None(ADD None(ADD MPGRP) ADD
IPCLKLNK) None(ADD MPLNK) IP2RSCGRP(Optio
None
None(ADD None(ADD OMCH) nal)
IPPATH) None(ADD ADD
None(ADD IPRT) RSCGRP) IPCLKLNK(Optional
None(ADD None(ADD )
MPGRP) SAALLNK) ADD
None(ADD None(ADD IPPATH(Optional)
MPLNK) SCTPLNK) ADD
None(ADD OMCH) None(ADD UNILNK) IPRT(Optional)
None(ADD None(ADD CFMMA) ADD
RSCGRP) None(ADD MPGRP(Optional)
None(ADD CFMMEP) ADD
SAALLNK) None(ADD MPLNK(Optional)
None(ADD BFDSESSION) ADD
SCTPLNK) None(ADD ETHTRK) OMCH(Optional)
None(ADD None(ADD ADD
UNILNK) ETHTRKLNK) RSCGRP(Optional)
None(ADD ADD
None(SET NodeB(SET
E1T1BEAR) None(SET E1T1BEAR)
None(SET E1T1BEAR) NodeB(SET
E1T1LOP) None(SET E1T1LOP)
None(SET E1T1LOP) NodeB(SET
E1T1WORKMOD None(SET E1T1WORKMODE)
E) E1T1WORKMODE) Ethport(SET
None(SET None(SET ETHPORT)
ETHPORT) ETHPORT) NodeB(SET None
None(SET None(SET HSDPAFLOWCTR
HSDPAFLOWCTR HSDPAFLOWCTRL LPARA)
LPARA) PARA) NodeB(SET
None(SET None(SET IPREMOTELOOP)
IPREMOTELOOP) IPREMOTELOOP) NodeB(SET LR)
None(SET LR) None(SET LR) IMA Group/UNI
None(SET None(SET SCRAM) Link/Fractional
SCRAM) ATM(SET SCRAM)
 When [PARA]SECT[/PARA]
is set to
REMOTE_SECTOR, the
None None Cell value range is 0.
When [PARA]SECT[/PARA]
is LOCAL_SECTOR, the
value range is 0~5.
When [PARA]SECT[/PARA]
is set to
REMOTE_SECTOR, the
None None Cell value range is 0.
When [PARA]SECT[/PARA]
is LOCAL_SECTOR, the
value range is 0~5.
This para is valid, when
0 0 Cell [PARA]SECT[/PARA] is
DIST_SECTOR
This para is valid, when
0 0 Cell [PARA]SECT[/PARA] is
DIST_SECTOR

None None NodeB None

None None NodeB None

None None NodeB None

None None NodeB None

None None NodeB None

None None NodeB None

None None NodeB None

None None NodeB None

The parameter is valid only

when the
[PARA]TYPE[/PARA] in
None None NEMU
[MML]SET
NEMUANLGIN[/MML] is set
to "VOLTAGE".
 The parameter is valid only
when the
[PARA]TYPE[/PARA] in
None None NEMU
[MML]SET
NEMUANLGIN[/MML] is set
to "CURRENT".

The parameter is valid only

when the
[PARA]TYPE[/PARA] in
[MML]SET
NEMUANLGIN[/MML] is set
None None NEMU to "VOLTAGE".
This parameter value must
be greater than
[PARA]SOLL[/PARA] in
[MML]SET
NEMUANLGIN[/MML].

The parameter is valid only

when the
[PARA]TYPE[/PARA] in
[MML]SET
NEMUANLGIN[/MML] is set
None None NEMU to "CURRENT";
This parameter value must
be greater than
[PARA]SOLL[/PARA] in
[MML]SET
NEMUANLGIN[/MML].
This parameter is valid only
when [PARA]SW[/PARA] in
None None NodeB [MML]SET
SNTPCLTPARA[/MML] is set
to "ON".
AAL2 Path(ADD
AAL2PATH)
NodeB(ADD
This parameter is valid only
IP2RSCGRP)
when the
NodeB(ADD
0 None [PARA]JNRSCGRP[/PARA]
IPPATH)
in the MML command is
NodeB(ADD
ENABLE.
RSCGRP)
SAAL(ADD
SAALLNK)
This parameter is valid noly
When the
None None Cell [PARA]HISPM[/PARA] in
[MML]ADD LOCELL[/MML]
is TRUE.
None None No involved None

The value range is 0~1 when

[PARA]SRCPT[/PARA] is
IMA and
[PARA]SRCSBT[/PARA] is
BASE_BOARD;
The value range is 0~3 when
[PARA]SRCPT[/PARA] is
IMA and
[PARA]SRCSBT[/PARA] is
E1_COVERBOARD;
0 None NodeB
The value range is 0~3 when
[PARA]SRCPT[/PARA] is
UNI and
[PARA]SRCSBT[/PARA] is
BASE_BOARD;
The value range is 0~7 when
[PARA]SRCPT[/PARA] is
UNI and
[PARA]SRCSBT[/PARA] is
E1_COVERBOARD;

The value range is 0~3 when

[PARA]SRCPT[/PARA] is
FRAATM and
[PARA]SRCSBT[/PARA] is
BASE_BOARD;
0 None NodeB
The value range is 0~7 when
[PARA]SRCPT[/PARA] is
FRAATM and
[PARA]SRCSBT[/PARA] is
E1_COVERBOARD;
The value range is 0~3 when
[PARA]SRCSBT[/PARA] is
BASE_BOARD;
None None NodeB
The value range is 0~7 when
[PARA]SRCSBT[/PARA] is
E1_COVERBOARD;
None None NodeB None

This parameter is valid when

the [PARA]SBT[/PARA]
parameter is
CHANNELLED_COVERBO
ARD and [PARA]SW[/PARA]
ENABLE None STM1
is set to ENABLE in
[MML]SET
SDHJ0J1J2[/MML]. Only
ENABLE is valid when
[PARA]TB[/PARA] is J2.
When the value range of
None(ADD NodeB(ADD
-(ADD [PARA]SRCSN[/PARA] is
TREELNKPVC) TREELNKPVC)
TREELNKPVC) 6~7,
None(ADD NodeB(ADD
-(ADD TSCROSS) [PARA]SRCSBT[/PARA] is
TSCROSS) TSCROSS)
BASE_BOARD.
When the value range of
None(ADD NodeB(ADD
-(ADD [PARA]SRCSN[/PARA] is
TREELNKPVC) TREELNKPVC)
TREELNKPVC) 0~5,
None(ADD NodeB(ADD
-(ADD TSCROSS) [PARA]SRCSBT[/PARA] is
TSCROSS) TSCROSS)
E1_COVERBOARD.

None None NodeB None

The value range is 0~7 when

the value range of
[PARA]NO[/PARA] in
[MML]ADD
TSCROSS[/MML] is 0~7;
The value range is 0~5 when
None None NodeB the value range of
[PARA]NO[/PARA] in
[MML]ADD
TSCROSS[/MML] is 8~15;
The [PARA]SRCSN[/PARA]
and [PARA]DSTSN[/PARA]
should be different.

None None NodeB None

When SBT is
BASE_BOARD, choose
NEXTHOP or IF
None None NodeB
When SBT is
E1_COVERBOARD, choose
IF
None None None None

The value range is 8~100000

when [PARA]PT[/PARA] is
ETH;
The value range is 8~1984
None None IP Path when [PARA]PT[/PARA] is
PPP;
The value range is 8~31744
when [PARA]PT[/PARA] is
MPGRP;
It is valid when
[PARA]SEHICHPCMOD[/PA
None 88 Cell RA] is RNC_BASED,
FOLLOW_TPC in [MML]SET
MACEPARA[/MML].
MASTER(ADD MASTER(ADD The value and relation of
SUBRACK) SUBRACK) Cabinet No., Subrack
None(ADD None(ADD No.and Slot No.:
CABINET) CABINET) Cabinet No. Subrack No.
MASTER(BLK MASTER(BLK BRD) Slot No. Board type
BRD) MASTER(SET 0 0 0~3 WBBPa (WCDMA
MASTER(SET SASUVSWRTHD) BaseBand Process unit type
SASUVSWRTHD) MASTER(SET A) \WBBPb (WCDMA
MASTER(SET RTWPINITADJ) BaseBand Process unit type
RTWPINITADJ) MASTER(SET B) \UTRP (Universal
MASTER(SET TXSW) extension TRansmission
TXSW) MASTER(SET Processing unit)
MASTER(SET IFOFFSET) 0 0 4~5 UTRP (Universal
IFOFFSET) MASTER(SET extension TRansmission
MASTER(SET RXATTEN) Processing unit)
RXATTEN) MASTER(SET 0 0 6~7 WMPT (WCDMA
MASTER(SET RFDESPARAM) Main Processing &
NodeB
RFDESPARAM) MASTER(SET Transmission unit)
MASTER(SET VSWRALMPARAM) 0 0 16 UBF (Universal BBU
VSWRALMPARA MASTER(STR Fan unit)
M) VSWRTEST) 0 0 18~19 UPEA(Universal
MASTER(STR MASTER(SET Power and Environment
VSWRTEST) RXSW) interface unit type A(-48V))
MASTER(SET MASTER(STR \UPEB(Universal Power and
RXSW) CLKTST) Environment interface unit
MASTER(STR MASTER(STR type B(24V))
CLKTST) RRULNKTST) \UEIU(Universal
MASTER(STR MASTER(STR Environment Interface Unit)
RRULNKTST) BATTST) 0 6 0 NEMU (NodeB
MASTER(STR MASTER(SET Environment Monitoring Unit)
BATTST) HTPROTECT) 0 7 0 NPMU (NodeB Power
MASTER(SET MASTER(SET Monitoring Unit)
HTPROTECT) BCFCVOLTAGE) 0 8 0~1 NCMU (NodeB
MASTER(SET MASTER(STR Climate Monitoring Unit)
 None(ADD LNKSRC) NodeB(ADD
None(ADD DEVIP) LNKSRC)
None(ADD PPPLNK) NodeB(ADD
-(ADD LNKSRC)
None(ADD DEVIP)
-(ADD DEVIP)
AAL2PATH) PPP Link(ADD
-(ADD PPPLNK)
None(ADD FRAATM) PPPLNK)
-(ADD AAL2PATH)
None(ADD IMAGRP) AAL2 Path(ADD
-(ADD FRAATM)
None(ADD IMALNK) AAL2PATH)
-(ADD IMAGRP)
None(ADD Fractional
-(ADD IMALNK)
IP2RSCGRP) ATM(ADD
-(ADD
None(ADD FRAATM)
IP2RSCGRP)
IPCLKLNK) IMA Group(ADD
-(ADD IPCLKLNK)
None(ADD IPPATH) IMAGRP)
-(ADD IPPATH)
None(ADD IPRT) IMA Link(ADD
-(ADD IPRT)
None(ADD MPGRP) IMALNK)
-(ADD MPGRP)
None(ADD MPLNK) NodeB(ADD
-(ADD MPLNK)
None(ADD OMCH) IP2RSCGRP)
-(ADD OMCH) None
None(ADD NodeB(ADD
-(ADD RSCGRP)
RSCGRP) IPCLKLNK)
-(ADD SAALLNK)
None(ADD IP Path(ADD
-(ADD SCTPLNK)
SAALLNK) IPPATH)
-(ADD
None(ADD NodeB(ADD IPRT)
TREELNKPVC)
SCTPLNK) MLPPP Group(ADD
-(ADD TSCROSS)
None(ADD MPGRP)
-(ADD UNILNK)
TREELNKPVC) MLPPP Link(ADD
-(ADD CFMMA)
None(ADD MPLNK)
-(ADD CFMMEP)
TSCROSS) OMCH(ADD
-(ADD
None(ADD UNILNK) OMCH)
BFDSESSION)
None(ADD CFMMA) NodeB(ADD
-(ADD ETHTRK)
None(ADD RSCGRP)
-(ADD
CFMMEP) SAAL(ADD
ETHTRKLNK)
None(ADD SAALLNK)
BFDSESSION) SCTP(ADD
None(ADD ETHTRK) SCTPLNK)
None(SET NodeB(SET
E1T1BEAR) None(SET E1T1BEAR)
None(SET E1T1BEAR) NodeB(SET
E1T1LOP) None(SET E1T1LOP)
None(SET E1T1LOP) NodeB(SET
E1T1WORKMOD None(SET E1T1WORKMODE)
E) E1T1WORKMODE) Ethport(SET
None(SET None(SET ETHPORT)
ETHPORT) ETHPORT) NodeB(SET None
None(SET None(SET HSDPAFLOWCTR
HSDPAFLOWCTR HSDPAFLOWCTRL LPARA)
LPARA) PARA) NodeB(SET
None(SET None(SET IPREMOTELOOP)
IPREMOTELOOP) IPREMOTELOOP) NodeB(SET LR)
None(SET LR) None(SET LR) IMA Group/UNI
None(SET None(SET SCRAM) Link/Fractional
SCRAM) ATM(SET SCRAM)
 When [PARA]SECT[/PARA]
is set to
REMOTE_SECTOR, the
None None Cell value range is 20~254.
When [PARA]SECT[/PARA]
is LOCAL_SECTOR, the
value of this para is 4~5.
When [PARA]SECT[/PARA]
is set to
REMOTE_SECTOR, the
None None Cell value range is 20~254.
When [PARA]SECT[/PARA]
is LOCAL_SECTOR, the
value of this para is 4~5.
This para is valid, when
None None Cell [PARA]SECT[/PARA] is
DIST_SECTOR
This para is valid, when
None None Cell [PARA]SECT[/PARA] is
DIST_SECTOR

0 0 NodeB None

0 0 NodeB None

0 0 NodeB None

0 0 NodeB None

0 0 NodeB None

0 0 NodeB None

0 0 NodeB None

0 0 NodeB None

None None NodeB None

 This parameter is valid when
the [PARA]RSW[/PARA] is
ENABLE.
When [PARA]TB[/PARA] is
J0: TRACE_1BYTE and
TRACE_16BYTE and
None None STM1
TRACE_64BYTE is valid.
When [PARA]TB[/PARA] is
J1: TRACE_16BYTE and
TRACE_64BYTE is valid.
When [PARA]TB[/PARA] is
J2: TRACE_16BYTE is valid.

This parameter is valid when

the [PARA]RSW[/PARA] is
ENABLE.
It should be A integer(0~255)
or a string consist of single
space, A-Z, a-z, 0-9.
When [PARA]RXT[/PARA] is
TRACE_1BYTE, it should
None None STM1 be an integer(0~255).
When [PARA]RXT[/PARA] is
TRACE_16BYTE, it should
be a string which length is
not more than 15.
When [PARA]RXT[/PARA] is
TRACE_64BYTE, it should
be a string which length is
not more than 62.

This parameter is valid when

[PARA]RXT[/PARA] is
EARLIER_VER None STM1
TRACE_16BYTE or
TRACE_64BYTE.

0 None SAAL None

This parameter is valid when

in [MML]ADD
TREELNKPVC[/MML]
None None Tree Link PVC [PARA]ST[/PARA] is set to
RTVBR or NRTVBR, and its
value should be less than the
[PARA]PCR[/PARA].
 [PARA]ST[/PARA] is valid
while
None None NodeB
[PARA]DST[/PARA]=YES in
[MML]SET TZ[/MML].

None None NodeB None

This parameter is valid only

when [PARA]ST[/PARA] in
[MML]ADD
AAL2PATH[/MML] is set to
None None AAL2 Path
RTVBR or NRTVBR, and
the value of this parameter
should be smaller than the
[PARA]PCR[/PARA] value.

None None NodeB None

This parameter is valid when

None None NodeB the operating mode is
SECTOR.

None None NodeB None

 For the UNI link on the
Fractional baseboard, the scrambling
ATM(ADD mode must be enabled when
FRAATM) the line code of AMI is used
ENABLE ENABLE IMA Group(ADD by the E1/T1 link. If the line
IMAGRP) code of AMI is used by an
UNI Link(ADD IMA link of the IMA group,
UNILNK) the scrambling mode of the
IMA group must be enabled.

0 None SCTP None

This parameter is invalid

when [PARA]DEVTP[/PARA]
None None NodeB
in [MML]ADD ALD[/MML] is
set to "SINGLE_RET"

None None NodeB None

0.0.0.0 None SCTP None

[PARA]SWEEK[/PARA] is
valid while
[PARA]DST[/PARA]=YES
None None NodeB
and [PARA]SM[/PARA] is
DATEWEEK or WEEK in
[MML]SET TZ[/MML].
0.0.0.0 None SCTP None

None None NodeB None

None None Cell None

[PARA]SWSEQ[/PARA] is
valid while
[PARA]DST[/PARA]=YES
None None NodeB
and
[PARA]SM[/PARA]=WEEK
in [MML]SET TZ[/MML].

None None NodeB None

80 80 NodeB None

This parameter is valid only

when [PARA]TT[/PARA] in
MASTER None NodeB [MML]ADD
RRUCHAIN[/MML] is set to
"RING"
This parameter is valid only
when
[PARA]JNRSCGRP[/PARA]
0 None Tree Link PVC
in [MML]ADD
TREELNKPVC[/MML] is set
to ENABLE.
The TDSTM is valid only
when
[PARA]ATMODE[/PARA] in
[MML]SET BATATPA[/MML]
120 None Battery
is set to PERIOD or
PERIODPOWERCUT.The
DDSTM value must be
smaller than TDSTM value.
None None NodeB None

This parameter is valid when

in [MML]SET
ALDDEV[/MML]
None None No [PARA]DEVVER[/PARA] is
set to OPE and
[PARA]DEVVER[/PARA] is
set to V1.1.
This parameter is valid when
in [MML]SET
ALDDEV[/MML]
None None No [PARA]DEVVER[/PARA] is
set to DEV and
[PARA]DEVVER[/PARA] is
set to V2.0_3GPP.
 [ADD TSCROSS]
When the source or
destination port of the
timeslot cross connection is
carried at the WMPT,
TscrossNo ranges from 0 to
7. When the source or
destination ports of the
timeslot cross connection are
carried at the UAEC,
TscrossNo ranges from 0 to
15.
The source E1/T1 link over
which timeslot cross
connection is configured
cannot carry the
IMA/UNI/FRAATM link or the
None None Timeslot Cross
PPP/MP link.
For a timeslot cross
connection, the source and
destination timeslots can be
different timeslots at different
boards. The number of
source timeslots, however,
must be equal to that of the
destination timeslots.
If the sub-board type is
BASE_BOARD, only eight
timeslot cross connections
are supported.
The number of
[PARA]DSTTSN[/PARA] and
[PARA]SRCTSN[/PARA]
timeslots must be equal.
This parameter is valid only
when [PARA]VST[/PARA] in
None None Tree Link PVC [MML]ADD
TREELNKPVC[/MML] is set
to VC_SWITCH.

None None Tree Link PVC None

[PARA]TLL[/PARA] is less
than [PARA]TUL[/PARA]
None None No
in[MML]MOD
NEMUTHLIMIT[/MML]
 45 None NCMU None

It is valid when
[PARA]MANUALSW[/PARA]
None None NodeB
is ON in [MML]SET
EMGLICENSE[/MML].
[PARA]TO[/PARA] is valid
while
None None NodeB
[PARA]DST[/PARA]=YES in
[MML]SET TZ[/MML].

None None NodeB None

This parameter is valid only

when [PARA]TT[/PARA] in
None None NodeB [MML]ADD
RRUCHAIN[/MML] is set to
"RING"

RTVBR None Tree Link PVC None

RTVBR None AAL2 Path None

The value is 0 when

[PARA]SBT[/PARA] is
CHANNELLED_COVERBO
ARD;
0 None STM1
The value range is 0~1 when
[PARA]SBT[/PARA] is
UNCHANNELLED_COVER
BOARD;
This parameter is valid only
when [PARA]TT[/PARA] in
None None NodeB [MML]ADD
RRUCHAIN[/MML] is set to
"RING"
This parameter is valid only
when [PARA]TT[/PARA] in
0 0 NodeB [MML]ADD
RRUCHAIN[/MML] is set to
"RING"

None None NodeB None

[PARA]TLL[/PARA] is less
than [PARA]TUL[/PARA]
None None No
in[MML]MOD
NEMUTHLIMIT[/MML]
This parameter is valid only
when in [MML]ADD
IPPATH[/MML] the value of
[PARA]PT[/PARA] is set to
ETH and
[PARA]FPMUXSWITCH[/PA
127 127 IP Path RA] is set to ENABLE.
The difference between
[PARA]FRAMELEN[/PARA](
Frame Max Length) and
[PARA]SUBFRAMELEN[/PA
RA](Sub Frame Max Length)
is greater than 4.

Only ENABLE is valid when

ENABLE None STM1
[PARA]TB[/PARA] is J2.
 The value range is J0~J2
when [PARA]SBT[/PARA] is
CHANNELLED_COVERBO
ARD;
J0 None STM1
The value range is J0~J1
when [PARA]SBT[/PARA] is
UNCHANNELLED_COVER
BOARD;
This parameter is valid only
when in [MML]ADD
IPPATH[/MML] the value of
1 1 IP Path [PARA]PT[/PARA] is set to
ETH and
[PARA]FPMUXSWITCH[/PA
RA] is set to ENABLE.
IMA Group(ADD
IMAGRP)
DISABLE None None
UNI Link(ADD
UNILNK)

0 0 NodeB None

None None NodeB None

 MLPPP Link(ADD
MPLNK)
PPP Link(ADD
None None PPPLNK) None
Fractional
ATM(ADD
FRAATM)

The value range is 8~100000

when [PARA]PT[/PARA] is
ETH.
The value range is 8~1984
None None IP Path when [PARA]PT[/PARA] is
PPP.
The value range is 8~31744
when [PARA]PT[/PARA] is
MPGRP.
None None NodeB None

None None NEMU None

You must enter the

parameter when the ALD
system type
[PARA]AST[/PARA]in
[MML]SET
ALDPWRSW[/MML] is set to
None None NodeB
"CUSTOM".
Alarm Clear Threshold must
be
satisfied:UOTHD<UCTHD<O
OTHD;UOTHD<OCTHD<OO
THD
UL is more than
[PARA]LL[/PARA] in
57 57 NodeB
[MML]SET
NEMUINVLIMIT[/MML]
 When [PARA]PT[/PARA] in
[MML]SET ALMPORT[/MML]
None None NodeB
is VALUE, this parameter is
valid.
For DBS:It is valid when
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, R0B.
For BTS:It is valid when
100(ADD SEC) 100(ADD SEC) Cell
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, R0B, N0A, N0B, N1A,
N1B, N2A, N2B, N3A, N3B,
N4A, N4B, N5A, N5B.
For DBS:It is valid when
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, R0B.
For BTS:It is valid when
100(ADD SEC) 100(ADD SEC) Cell
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, R0B, N0A, N0B, N1A,
N1B, N2A, N2B, N3A, N3B,
N4A, N4B, N5A, N5B.
For DBS:It is valid when
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, R0B.
For BTS:It is valid when
100(ADD SEC) 100(ADD SEC) Cell
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, R0B, N0A, N0B, N1A,
N1B, N2A, N2B, N3A, N3B,
N4A, N4B, N5A, N5B.
For DBS:It is valid when
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, R0B.
For BTS:It is valid when
100(ADD SEC) 100(ADD SEC) Cell
[PARA]ANT1N[/PARA] in
[MML]ADD SEC[/MML] is
R0A, R0B, N0A, N0B, N1A,
N1B, N2A, N2B, N3A, N3B,
N4A, N4B, N5A, N5B.
None None Cell None

None None NodeB None

0 None Cell None

None None IP Path None

None None IP Path None

You must enter the

parameter when the ALD
system type
[PARA]AST[/PARA]in
[MML]SET
ALDPWRSW[/MML] is set to
None None NodeB
"CUSTOM".
Alarm Clear Threshold must
be
satisfied:UOTHD<UCTHD<O
OTHD;UOTHD<OCTHD<OO
THD

None None Cell None

None None NodeB None

 This parameter is valid when
[PARA]SW[/PARA] is
ENABLE
When [PARA]SBT[/PARA] is
UNCHANNELLED_COVER
BOARD, only
TRACE_64BYTE is valid.
When [PARA]SBT[/PARA] is
CHANNELLED_COVERBO
None None STM1 ARD:
For [PARA]TB[/PARA]=J0,
TRACE_1BYTE ,
TRACE_16BYTE and
TRACE_64BYTE are valid.
For [PARA]TB[/PARA]=J1,
TRACE_16BYTE and
TRACE_64BYTE are valid.
For [PARA]TB[/PARA]=J2,
TRACE_16BYTE is valid.

This parameter is valid when

[PARA]SW[/PARA] is
ENABLE.
It should be A integer(0~255)
or a string consist of single
space, A-Z, a-z, 0-9.
When
[PARA]TXT[/PARA]=TRACE
_1BYTE, it should be an
integer(0~255).
None None STM1
When
[PARA]TXT[/PARA]=TRACE
_16BYTE, it should be a
string which length is not
more than 15.
When
[PARA]TXT[/PARA]=TRACE
_64BYTE, it should be a
string which length is not
more than 62.

None None NodeB None

 This parameter is valid when
[PARA]TXT[/PARA] is
EARLIER_VER None STM1
TRACE_16BYTE or
TRACE_64BYTE.

MLPPP Group(ADD
This parameter is mandatory
MPGRP)
None None if [PARA]AUTH[/PARA] is
PPP Link(ADD
not NONAUTH.
PPPLNK)
The value range is 0~3 when
[PARA]SBT[/PARA] is
BASE_BOARD.
0 None UNI Link
The value range is 0~7 when
[PARA]SBT[/PARA] is
E1_COVERBOARD.
AAL2 Path(ADD
AAL2PATH)
None None None
SAAL(ADD
SAALLNK)

V1.1 V1.1 IMA Group None

[SET VLANCLASS]
A parameter is added.
Only eight different VLAN
IDs are allowed.
This parameter is valid only
0 None NodeB
when
[PARA]VLANMODE[/PARA]
in [MML]ADD
VLANMAP[/MML] is set to
SINGLEVLAN.
This parameter is valid when
in [MML]ADD
VLANMAP[/MML]
1 None NodeB [PARA]VLANMODE[/PARA]
is set to SINGLEVLAN and
[PARA]INSTAG[/PARA] is
set to ENABLE.

None None NodeB None

 This parameter is valid when
[PARA]VLANMODE[/PARA]
in [MML]ADD
VLANMAP[/MML] is set to
0 None NodeB SINGLEVLAN and
[PARA]INSTAG[/PARA] in
[MML]ADD
VLANMAP[/MML] is set to
ENABLE.
AAL2 Path(ADD
AAL2PATH)
None None None
SAAL(ADD
SAALLNK)

None None Tree Link PVC None

0 None NodeB None

When the para

[PARA]WM[PARA] of
[MML]SET DEMODE[/MML]
is DEM_2_CHAN, There will
be 1 or 2 antena;
When the para
DEM_2_CHAN DEM_2_CHAN NodeB
[PARA]WM[PARA] of
[MML]SET DEMODE[/MML]
is DEM_4_CHAN or
DEM_ECON_4_CHAN,
There will be 1 or 2 or 4
antenas;
None None NodeB None

0 None RRU None

This parameter is valid when

[PARA]SD[/PARA] in
0 None RRU [MML]SET
RXINTDETSW[/MML] is set
to ON.

This parameter is valid when

[PARA]SD[/PARA] in
None None RRU [MML]SET
RXINTDETSW[/MML] is set
to ON.
 This parameter is valid when
[PARA]SD[/PARA] in
None None RRU [MML]SET
RXINTDETSW[/MML] is set
to ON.

This parameter is valid when

[PARA]SD[/PARA] in
5s None RRU [MML]SET
RXINTDETSW[/MML] is set
to ON.
This parameter is valid when
[PARA]SD[/PARA] in
None None RRU [MML]SET
RXINTDETSW[/MML] is set
to ON.
This parameter is valid when
[PARA]SD[/PARA] in
None None RRU [MML]SET
RXINTDETSW[/MML] is set
to ON.

0xFF None RRU None

This parameter is valid when

[PARA]NMCA[/PARA] in
0 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 1~8.
This parameter is valid when
[PARA]NMCA[/PARA] in
0 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 1~8.
This parameter is valid when
[PARA]NMCA[/PARA] in
1 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 2~8.
This parameter is valid when
[PARA]NMCA[/PARA] in
0 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 2~8.
This parameter is valid when
[PARA]NMCA[/PARA] in
2 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 3~8.
 This parameter is valid when
[PARA]NMCA[/PARA] in
0 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 3~8.
This parameter is valid when
[PARA]NMCA[/PARA] in
3 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 4~8.
This parameter is valid when
[PARA]NMCA[/PARA] in
0 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 4~8.
This parameter is valid when
[PARA]NMCA[/PARA] in
0 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 5~8.
This parameter is valid when
[PARA]NMCA[/PARA] in
1 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 5~8.
This parameter is valid when
[PARA]NMCA[/PARA] in
1 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 6~8.
This parameter is valid when
[PARA]NMCA[/PARA] in
1 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 6~8.
This parameter is valid when
[PARA]NMCA[/PARA] in
2 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 7~8.
This parameter is valid when
[PARA]NMCA[/PARA] in
1 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 7~8.
This parameter is valid when
[PARA]NMCA[/PARA] in
3 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 8.
 This parameter is valid when
[PARA]NMCA[/PARA] in
1 None RRU [MML]SET
RXINTDETSW[/MML] is set
to 8.

The Rate Unit of a NodeB is

kbps kbps NodeB
unitive

HW_DEFINED HW_DEFINED NodeB None

This parameter is valid when

[PARA]ICPT[/PARA] in
0 None NodeB [MML]ADD
IPCLKLNK[/MML] is set to
PTP.

MASTER MASTER NodeB None

None None ETH OAM None

0 None ETH OAM None

None None ETH OAM None

None None ETH OAM None

None None NodeB None

None None ETH OAM None

None None ETH OAM None

None None ETH OAM None

None None ETH OAM None

 When [PARA]SBT[/PARA] is
BASE_BOARD, choose
ETH(ETH);
ETH None ETH OAM When [PARA]SBT[/PARA] is
ETH_COVERBOARD,
choose ETH(ETH),
ETHTRK(ETHTRK);
The value range is 0~3 when
[PARA]PT[/PARA] is ETH.
None None ETH OAM The value range is 0~1 when
[PARA]PT[/PARA] is
ETHTRK.

None None NodeB None

None None NodeB None

None None NodeB None

None None NodeB None

10 10 NodeB None

10 10 NodeB None

3 None NodeB None

0 None NodeB None

DISABLE None NodeB None

DISABLE None NodeB None

100 None NodeB None

0 None NodeB None

None None NodeB None

None 2 Cell None

None 4 Cell None

None CQI Cell None

None CQI Cell None

This parameter is valid when

[PARA]HSSCCHPWRCTRL
METHODINDCH[/PARA] in
None 10 Cell
[MML]SET
MACHSPARA[/MML] is set
to CQI

None NO_CQI_ADJ Cell None

None NO_CQI_ADJ Cell None

 This parameter is valid when
[PARA]CQIADJALGOFCON[
None 7 Cell /PARA] in [MML]SET
MACHSPARA[/MML] is set
to CQI_ADJ_BY_RBLER

None OPEN Cell None

None OPEN Cell None

None None Cell None

None None Cell None

50 50 Cell None

10 10 Cell None

None None Cell None

INHBOARD INHBOARD CELL None

GEN_POOL INHBOARD CELL None

ENABLE None NodeB None

0 None RRU None

0 None RRU None

The parameter is valid when

None None RRU the detect switch is set to
ON.
 The parameter is valid when
None None RRU the detect switch is set to
ON.

The parameter is valid when

5s None RRU the detect switch is set to
ON.
The parameter is valid when
None None RRU the detect switch is set to
ON.
The parameter is valid when
None None RRU the detect switch is set to
ON.

0xFF None RRU None

The parameter is valid when

0 None RRU
NMCA is set to 1~8.

The parameter is valid when

0 None RRU
NMCA is set to 1~8.

The parameter is valid when

1 None RRU
NMCA is set to 2~8.

The parameter is valid when

0 None RRU
NMCA is set to 2~8.

The parameter is valid when

2 None RRU
NMCA is set to 3~8.

The parameter is valid when

0 None RRU
NMCA is set to 3~8.

The parameter is valid when

3 None RRU
NMCA is set to 4~8.

The parameter is valid when

0 None RRU
NMCA is set to 4~8.

The parameter is valid when

0 None RRU
NMCA is set to 5~8.

The parameter is valid when

1 None RRU
NMCA is set to 5~8.

The parameter is valid when

1 None RRU
NMCA is set to 6~8.
 The parameter is valid when
1 None RRU
NMCA is set to 6~8.

The parameter is valid when

2 None RRU
NMCA is set to 7~8.

The parameter is valid when

1 None RRU
NMCA is set to 7~8.

The parameter is valid when

3 None RRU
NMCA is set to 8.

The parameter is valid when

1 None RRU
NMCA is set to 8.

When [PARA]SBT[/PARA] is
BASE_BOARD, choose IMA
(IMAGRP), UNI (UNILNK),
or FRAATM (FRAATM);
AAL2 Path(ADD When [PARA]SBT[/PARA] is
AAL2PATH) CHANNELLED_COVERBO
OMCH(ADD ARD, choose IMA
OMCH) (IMAGRP) or UNI (UNILNK);
IMA IMA
NodeB(ADD When [PARA]SBT[/PARA] is
RSCGRP) UNCHANNELLED_COVER
SAAL(ADD BARD, choose STM1
SAALLNK) (Unchannelled STM1);
When [PARA]SBT[/PARA] is
E1_COVERBOARD, choose
IMA (IMAGRP), UNI
(UNILNK).

NodeB(ADD
DEVIP)
NodeB(ADD
IP2RSCGRP)
IP Path(ADD
None None None
IPPATH)
OMCH(ADD
OMCH)
NodeB(ADD
RSCGRP)
 NodeB(ADD
DEVIP)
NodeB(ADD
IP2RSCGRP)
IP Path(ADD
None None None
IPPATH)
OMCH(ADD
OMCH)
NodeB(ADD
RSCGRP)

NodeB(ADD
LNKSRC)
NodeB(ADD
DEVIP)
PPP Link(ADD
PPPLNK)
Fractional
ATM(ADD
None None FRAATM) None
IP Path(ADD
IPPATH)
MLPPP Link(ADD
MPLNK)
OMCH(ADD
OMCH)
SAAL(ADD
SAALLNK)
 When [PARA]SBT[/PARA] is
BASE_BOARD, choose IMA
(IMAGRP), UNI (UNILNK),
NodeB(ADD or FRAATM (FRAATM);
DEVIP) When [PARA]SBT[/PARA] is
NodeB(ADD CHANNELLED_COVERBO
IP2RSCGRP) ARD, choose IMA
IP Path(ADD (IMAGRP) or UNI (UNILNK);
None None
IPPATH) When [PARA]SBT[/PARA] is
OMCH(ADD UNCHANNELLED_COVER
OMCH) BARD, choose STM1
NodeB(ADD (Unchannelled STM1);
RSCGRP) When [PARA]SBT[/PARA] is
E1_COVERBOARD, choose
IMA (IMAGRP), UNI
(UNILNK).

AAL2 Path(ADD
AAL2PATH)
OMCH(ADD
OMCH)
None None None
NodeB(ADD
RSCGRP)
SAAL(ADD
SAALLNK)
 The value range is 0~1 when
IMA Group(ADD [PARA]SBT[/PARA] is
E1_COVERBOAR IMAGRP) BASE_BOARD;
E1_COVERBOARD
D IMA Link(ADD The value range is 0~3 when
IMALNK) [PARA]SBT[/PARA] is
E1_COVERBOARD;
MLPPP Group(ADD
MPGRP)
PPP Link(ADD
10 10 None
PPPLNK)
PPPoE Link(ADD
PPPOELNK)
MLPPP Group(ADD
MPGRP)
PPP Link(ADD
8 8 None
PPPLNK)
PPPoE Link(ADD
PPPOELNK)

MLPPP Group(ADD
E1_COVERBOAR MPGRP)
E1_COVERBOARD None
D MLPPP Link(ADD
MPLNK)

MLPPP Link(ADD
None None None
MPLNK)

MLPPP Link(ADD
None None None
MPLNK)

MLPPP Link(ADD
None None None
MPLNK)

MLPPP Link(ADD
0 0 None
MPLNK)

MLPPP Link(ADD
0 0 None
MPLNK)

MLPPP Link(ADD
CRC_16 CRC_16 None
MPLNK)

None None ETH OAM None

None None NodeB None

None None NodeB None

None None NodeB None

None None NodeB None

10 None NodeB None

95 None NodeB None

2 None NodeB None

1 None NodeB None

None None NodeB None

None None NodeB None

Access Service Interrupted During Modification Interruption Scope

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Y NodeB

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Y NodeB

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read Only Not involved Not involved

Read Only Y The board be actived

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Not involved Not involved

Read Only Not involved Not involved

Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read Only Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read Only Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Not involved NodeB

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved NodeB

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write Y NodeB

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Y Port

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Y Port

Read & Write Y Port

Read & Write Y Port

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Y Port

Read & Write Y Port

Read & Write Not involved Not involved

Read & Write Y Port

Read & Write Y Port

Read & Write Y Port

Read & Write Y NodeB

Read & Write Y NodeB

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Y Port

Read & Write Y Port

Read & Write Y Port

Read & Write Y Port

Read & Write Y Port

Read & Write Y Port

Read & Write Y Port

Read & Write Not involved Not involved

Read & Write Y Port

Read & Write Y Port

Read & Write Y Port

Read & Write Not involved Not involved

Read & Write Y Port

Read & Write Y Port

Y(SET ETHPORT)
Read & Write Port
N(ADD ETHTRK)

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Y NodeB

Read & Write Y NodeB

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Y NodeB

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Y NodeB

Read & Write Y NodeB

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Y NodeB

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Y NodeB

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read Only Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write Y NodeB

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved NodeB

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Y NodeB

Read & Write Not involved NodeB

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Y NodeB

Read & Write Y NodeB

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write N (No impact on the UE in idle mode) Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved
Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N (No impact on the UE in idle mode) Not involved

Read & Write N Not involved

Read & Write N Not involved

Read & Write N Not involved

Read & Write N Not involved

Read & Write N Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write No involved No involved

Read & Write Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write No involved No involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read Only Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

Read & Write Not involved Not involved

The parameter
Read & Write No involved modification has no impact
on the equipment.

Read & Write Not involved Not involved

Interruption Duration(Min) Caution

To modify the Mac-hs maximum

resource limit ratio parameters of the
Not involved
specified local cell, ensure that the
local cell supports HSDPA.
To modify the Mac-hs maximum
resource limit ratio parameters of the
Not involved
specified local cell, ensure that the
local cell supports HSDPA.

It only takes effect on the new user

after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.

To modify the Mac-hs resource Limit

scheduling parameters of the specified
Not involved
local cell, ensure that the local cell
supports HSDPA.
To modify the Mac-hs resource Limit
scheduling parameters of the specified
Not involved
local cell, ensure that the local cell
supports HSDPA.
To modify the Mac-hs resource Limit
scheduling parameters of the specified
Not involved
local cell, ensure that the local cell
supports HSDPA.
To modify the Mac-hs resource Limit
scheduling parameters of the specified
Not involved
local cell, ensure that the local cell
supports HSDPA.
To modify the Mac-hs resource Limit
scheduling parameters of the specified
Not involved
local cell, ensure that the local cell
supports HSDPA.
The ARP proxy needs to be enabled
when the local IP address of the OM
Not involved channel is in the same subnet as the
IP address of the Ethernet port on the
board of the same slot.

The gain range supported by the

STMA varies with models and vendors.
It is recommended that you list the gain
Not involved
range supported by the STMA by
running the DSP TMAFUN command
before setting the gain.
 Before setting the AC voltage alarm
threshold value, make sure whether
Not involved
the 220 V AC or 110 V AC power is
supplied to the NPMU.

Before setting the AC voltage alarm

threshold value, make sure whether
Not involved
the 220 V AC or 111 V AC power is
supplied to the NPMU.

The parameter modification has no

Not involved
impact on the equipment.

After the NodeB is started, the time

delay for starting BOOTP is set to 15
min by default, during which if the OM
channel returns to normal, the time
delay for starting BOOTP will be set to
"BootpTime" in this command and the
default value is 500000 min. If the time
delay for starting BOOTP is set to 15
min, after the OM channel is in
abnormal status for 15 min, and the
NCP is also abnormal, BOOTP will be
started. Every time the OM channel is
Not involved
found in normal state, the time delay
for starting BOOTP will be set to
BootpTime in this command. If you set
the BootpTime to a relatively short
period of time to trigger a BOOTP start,
then it is recommended that you set
the BootpTime to the default value
500000 min when the OM channel
returns to normal. In this way, the
BOOTP mistriggering caused by
transmission intermittent can be
prevented.

The parameter modification has no

Not involved
impact on the equipment.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.
 After you set an alarm to be shielded,
the NodeB handles the alarm
according to its current status. If the
alarm exists at that time, the NodeB
generates the alarm occurrence report.
Then, when the alarm is cleared
manually, the NodeB generates the
alarm clearance report. If the alarm
does not exist at that time, the NodeB
does not generate the alarm
occurrence report or clearance report.
When you set an alarm to be
unshielded, the NodeB handles the
Not involved
alarm according to its current status. If
the alarm exists at that time, the
NodeB generates the alarm occurrence
report. If the alarm does not exist at
that time, the NodeB does not
generate any report.
After you set an alarm to be
unshielded, the NodeB handles the
alarm in a normal way. If the alarm is
generated, the NodeB generates the
alarm occurrence report. If the alarm is
cleared, the NodeB generates the
alarm clearance report.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Reducing the Bit Error Rate (BER)

Not involved threshold of the NodeB lowers the
upper limit of the BER alarm threshold.
 The parameter modification has no
Not involved
impact on the equipment.

The configuration takes effect

immediately after the parameter is
Not involved modified.
This command is valid only for the
NEMU manufactured by Huawei.

The delayed discharge test time has a

Not involved direct impact on power-off test, timing
test and manual background test.

When no TMA is used, the attenuation

value is set to 0. When the 12 dB TMA
The service is affected until the is used, the attenuation value is set
configuration is correct. between 4 dB to 11 dB. When the 24
dB TMA is used, the attenuation value
is set between 11 dB and 22 dB.

The parameter modification has no

Not involved
impact on the equipment.
 This command can be run only by the
network administrator.
After the command is sent, the NE
uses a corresponding authentication
mode at the next SSL connection. This
command does not affect the existing
connections.
Not involved
When the identity is authenticated, the
NE must be configured with the root
certificate, public key certificate, and
private key certificate. If any of the
certificates is not configured, a
message is displayed, reporting that a
certificate is not configured.

The parameter modification has no

Not involved
impact on the equipment.

When multiple NodeBs are cascaded,

a lower-level node is connected to an
upper-level one through E1/T1 cables
and extracts the clock from the E1/T1
Not involved
cables. Therefore, the clock mode of
the upper-level node must be set as
master and that of the lower level node
must be set as slave.
The configuration takes effect
immediately after the parameter is
Not involved modified.
This command is valid only for the
NEMU manufactured by Huawei.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

APM100:Battery
Capacity(AH):100;Battery Current
Limiting Coefficient:0.15
APM200:Battery The parameter modification has no
Capacity(AH):200;Battery Current impact on the equipment.
Limiting Coefficient:0.15
APM30: Battery Capacity(AH):36;
Battery Current Limiting Coefficient:0.07

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

The value must be larger than the

Not involved value of the FCVOL and between 43.2
and 57.6.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The link is regarded as not congested

when the discard rate is lower than or
Not involved equal to this threshold, and thus the
congestion judgement may be
influenced by [PARA]DR[/PARA].

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 The backup mode of the chain or ring
decides whether the CPRI hot
redundancy is supported by the
equipment on the chain or ring.
Not involved
Currently only the MRRU supports the
CPRI hot redundancy. In this case, the
backup mode should be set as hot
redundancy.

The parameter modification has no

Not involved
impact on the equipment.

If this switch is not enabled, the added

SLAVE CP channel will not take effect.
If you disable this switch when the
NodeB is using the SLAVE CP
Not involved channel, the NodeB does not switch to
the MASTER CP when the MASTER
CP is restored. This switch should be
consistent with that of the RNC to
ensure communication.
For an RRU chain, only one break
point can be set and the chain can be
divided into two parts:
Part one consists of the RRUs
between the chain head and the break
point position. The services of the
RRUs in this part are not affected.
Part two consists of the RRUs between
the break point position and the chain
tail. The RRUs in this part are isolated,
and the services are disrupted. You
can rectify the fault through the RMV
RRUCHAINBRKPOS command. You
can run the DSP RRUCHAINSTATE
command to query the attributes of the
CPRI interfaces of the RRU.
The service is affected until the RRU For an RRU ring, two break points can
Chain configuration is correct be set and the ring can be divided into
three parts:
Part one consists of the RRUs
between the ring head and the first
break point position. The services of
the RRUs in this part may be affected.
Part two consists of the RRUs between
the break point positions. The RRUs in
this part are isolated, and the services
are disrupted. You can rectify the fault
through the RMV RRUCHAINBRKPOS
command.
Part three consists of the RRUs
between the second break point
position and the ring tail. The services
of the RRUs in this part may be
affected.
 For an RRU chain, only one break
point can be set and the chain can be
divided into two parts:
Part one consists of the RRUs
between the chain head and the break
point position. The services of the
RRUs in this part are not affected.
Part two consists of the RRUs between
the break point position and the chain
tail. The RRUs in this part are isolated,
and the services are disrupted. You
can rectify the fault through the RMV
RRUCHAINBRKPOS command. You
can run the DSP RRUCHAINSTATE
command to query the attributes of the
CPRI interfaces of the RRU.
For an RRU ring, two break points can
Not involved
be set and the ring can be divided into
three parts:
Part one consists of the RRUs
between the ring head and the first
break point position. The services of
the RRUs in this part may be affected.
Part two consists of the RRUs between
the break point positions. The RRUs in
this part are isolated, and the services
are disrupted. You can rectify the fault
through the RMV RRUCHAINBRKPOS
command.
Part three consists of the RRUs
between the second break point
position and the ring tail. The services
of the RRUs in this part may be
affected.
To enable the DHCP Relay function,
you need to run [MML]ADD
DHCPSVRIP[/MML] to add the DHCP
Server IP address, and you may need
Not involved
to run [MML]ADD IPRT[/MML] to add
related routes to ensure the current
NodeB can communicate with this IP
address.

The parameter modification has no

Not involved
impact on the equipment.

The BSDV is valid only when the

Not involved
BSDF is set to ENABLE.
 The parameter modification has no
Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Until be actived successfully. This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The gain range supported by the

SASU varies with models and vendors.
It is recommended that you list the gain
Not involved
range supported by the SASU by
running the DSP SASUFUN command
before setting the gain.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

For the E1 lines, the 75-ohm and 120-

ohm modes are supported; for the T1
lines, only the 100-ohm mode is
supported. After you modify the line
Not involved
impedance by running this command,
you must reset the Iub interface board
manually to make your modification
valid.
 If a clock source exists and the clock
mode is set to FREE, the clock source
is invalid and the clock works in free-
run mode.
The system clock works in free-run
mode when the clock source is faulty.
After the reference clock source is
restored, the NodeB uses the clock
source.
Ensure that the clock source is
available before running the command.
If the system uses the IP clock source,
the IP clock source can be configured
to automatic or manual mode. In
automatic IP mode, the IP source link
in a normal state and with a high
priority will be chosen as the clock
Not involved
source. In manual IP mode, the
cabinet number, subrack number, slot
number, and IP link number are
required, and they can be configured
successfully.
The command cannot be run when the
clock quality test is being performed.
If the system responds with a "Clock
source is unavailable" message after
you run the command, do as follows:
For the LINE clock source, check
whether the LINE clock is configured
through the DSP LNKSRC command.
If not, add the LINE clock source
through the ADD LNKSRC command.
For the GPS card clock source, check
whether the GPS is configured through
The parameter modification has no
Not involved
impact on the equipment.
Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter can not be modified.

Not involved This parameter cannot be modified.

Not involved This parameter can not be modified.

Not involved This parameter cannot be modified.

Not involved This parameter can not be modified.

Not involved This parameter cannot be modified.

Not involved This parameter can not be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

The IP address takes effect

immediately after it is configured. For
local maintenance, this command
might cause the interruption of the
maintenance channel. The IP address
and the subnet mask must be valid.
Any one of the IP addresses of the
Not involved local maintenance channel, Ethernet
port, and Operation and Maintenance
(OM) IP address must be unique. The
IP addresses of the FE port, local
maintenance channel, and remote
maintenance channel must be in
different network segments and are
free from the inclusion relation.
 The parameter modification has no
Not involved
impact on the equipment.

It only takes effect on the new user

after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

An auxiliary power system can supply

Not involved power to multiple RRUs. One RRU
controls this auxiliary power system.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
Modifying battery installation time will
clear all the saved battery test results of The parameter modification has no
NPMU. The NPMU restarts saving impact on the equipment.
battery test result.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

You can successfully run this

command only if the NCMU works
properly.
The configuration takes effect
immediately after the parameter is
modified.
The value of the Low Temperature
Critical Point must be smaller than that
Not involved of the High Temperature Critical Point.
This command is applicable to only the
NCMU of the direct-ventilation type
and that with a ventilation film.
This command can be run successfully
for the NCMU in the auxiliary power
system of the RRU only when the
power system is the APM30.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

 The DC load is used to simulate a TMA
in the BS system. In some situations,
when a high gain is set on the BS RX
path through the WCDMA NodeB, the
SASU should notify the BS BTS that a
TMA is connected to the antenna
system. It is preferable to install a DC
load to the BS BTS. In this way, the
Not involved
BS BTS can be notified about the TMA
on the antenna system when the DC
current on the antenna system is
detected.
The BS DC load cannot be enabled if
the DC power switch state of the SASU
is set to BS power supply mode.

The BS DC load will be automatically

changed to 7 after the antenna DC
power switch state is set to BS power
supply mode.
The antenna DC power switch state of
the SASU is only set on the main
Not involved antenna port. If you set the switch state
not on the main antenna port, it
responds with a Not Supported
message.
This setting is effective in both
subunits of the SASU simultaneously.

Before setting the AC voltage alarm

threshold value, make sure whether
Not involved
the 220 V AC or 111 V AC power is
supplied to the NPMU.
 Before setting the AC voltage alarm
threshold value, make sure whether
Not involved
the 220 V AC or 111 V AC power is
supplied to the NPMU.

The delayed discharge test time has a

Not involved direct impact on power-off test, timing
test and manual background test.

This parameter cannot be modified

Not involved
when the logical cell exists.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter cannot be equal to

[PARA]PEERIP[/PARA]. It is not
Not involved displayed when the value of
[PARA]LM[/PARA] is set to ALL or
NOLOOP.
 After this parameter is set, the
receiver sensibility will be reduced.
Not involved Adjust the receiver sensibility
according to network planning and
optimization.

Not involved This parameter cannot be modified.

Modifying delay may affect normal

access of a cell; The heavier the load
Not involved
in the cell is, the more obvious the
impact is.

Modifying delay may affect normal

access services of a cell; The heavier
Not involved
the load in the cell is, the more
obvious the impact is.

Modifying delay may affect normal

access services of a cell; The heavier
Not involved
the load in the cell is, the more
obvious the impact is.
 Modifying delay may affect normal
access services of a cell; the heavier
Not involved
the load in the cell is, the more
obvious the impact is.

This parameter cannot be modified

when the logical cell exists; The
downlink and uplink frequencies of the
local cell must stay within the same
frequency band; If the power amplify
unit can only support two carriers, then
in a Power Amplifier, the difference
between frequencies of local cells must
Not involved be greater or equal to
4.2MHz(21*0.2MHz), and be less or
equal to 5MHz(25*0.2MHz); If the
power amplify unit can support four
carriers, then in a Power Amplifier,
the difference between frequencies of
local cells must be greater or equal to
4.2MHz(21*0.2MHz), and be less or
equal to 15MHz(75*0.2MHz).

Not involved This parameter cannot be modified.

When the logical cell does not exist,

you can modify the downlink resource
group; if the downlink resource group
Not involved does not exist or the downlink resource
group is not the subset of the uplink
resource group, the execution of the
command fails.

The parameter cannot be equal to

[PARA]PEERIP[/PARA]. It is not
Not involved displayed when the value of
[PARA]LM[/PARA] is set to ALL or
NOLOOP.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The IP address takes effect

immediately after it is configured. For
local maintenance, this command
might cause the interruption of the
maintenance channel. The IP address
and the subnet mask must be valid.
Any one of the IP addresses of the
Not involved local maintenance channel, Ethernet
port, and Operation and Maintenance
(OM) IP address must be unique. The
IP addresses of the FE port, local
maintenance channel, and remote
maintenance channel must be in
different network segments and are
free from the inclusion relation.
The Alarm Report Synchronization will
Not involved be affected when the parameter is
modified.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

After you modify the E1/T1 bearing

mode of the Iub interface board by
running this command, you must reset
Not involved the board manually to make your
modification valid. The parameter can
be modified only when the board
supports this bearing mode.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

If the value of [PARA]OMPRI[/PARA]

is larger than that of the other sevices,
Not involved the OM channel will use the bandwidth
of the other sevices on the same
physical port.

It only takes effect on the new user

after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.
 It only takes effect on the new user
Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 When the encryption mode for
transmission is set to AUTO, the FTP
client tries to transmit data in
encryption mode first. If the
transmission fails, the FTP client
transmits data in plain text mode.
If the FTP client is set to support
Not involved firewalls, the FTP client sends the
CCC command to switch the data
transmitted in the control command
channel to plain text.
After this command is run successfully,
the settings take effect in the next FTP
operation.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The value must be greater than the

Not involved value of the DCVLL plus two and less
than that of the BCVOL.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

You can successfully enable or disable

the backup function of the WMPT
through this command if this function is
previously enabled or disabled.
The WMPT backup flag in the initial
Not involved data configuration file is ENABLE.
The modified WMPT backup flag is
stored in the data configuration file.
Therefore, the flag is still valid after
the NodeB is restarted.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Ensure that the transmission resource

group to be modified does exist, and
the bandwidth of the transmission
resource group after modification
should not be greater than the
bandwidth of the physical port carrying
Not involved them. If the bearing type of the
transmission resource group is IPV4,
the bandwidth of the transmission
resource group after modification
should not be smaller than the
bandwidth of IPPATH added to the
transmission resource group.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 If the value of [PARA]SIGPRI[/PARA]
is smaller than that of the other
Not involved
sevices, the user access may be
affected.

The parameter modification has no

Not involved
impact on the equipment.

The gain range supported by the

STMA varies with models and vendors.
It is recommended that you list the gain
Not involved
range supported by the STMA by
running the DSP TMAFUN command
before setting the gain.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 The running of the command fails if the
WMPT is not configured with a GPS
card.
For GPS feeders delivered by Huawei
Technologies Co. Ltd., the delay
Not involved equals the feeder length (m) multiplied
by 3.8 (ns/m).
For feeders delivered by other
vendors, contact the corresponding
vendors about the delay

The parameter modification has no

Not involved
impact on the equipment.

RRU num must be greater or equal

Not involved
than 2.

This parameter cannot be modified

Not involved
when the logical cell exists.

There must be a gap of no less than

Not involved 5% between the upper limit and the
lower limit of the humidity.

The inner handover radius of the local

Not involved cell must not be greater than cell
radius.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

For details, refer to <a href="BTS3836-

Not involved CABINET.htm">Subrack Information
Table</a>.
 You can successfully run this
command only if the NCMU works
properly.
The configuration takes effect
immediately after the parameter is
modified.
The value of the Low Temperature
Critical Point must be smaller than that
Not involved of the High Temperature Critical Point.
This command is applicable to only the
NCMU of the direct-ventilation type
and that with a ventilation film.
This command can be run successfully
for the NCMU in the auxiliary power
system of the RRU only when the
power system is the APM30.

You can successfully run this

command only if the NCMU works
properly.
The configuration takes effect
immediately after the parameter is
modified.
The value of the Heater Start
Temperature must be smaller than that
of the Heater Close Temperature.
The value of the Heater Close
Temperature should not be set too
Not involved large. Otherwise, the heat dissipation
of the system will be affected.
This command can be run successfully
for the NCMU in the auxiliary power
system of the RRU or BBU only when
the power system is the APM30.
It is recommended that you obtain the
current heater parameter values by
running the LST HTPA command
before setting the threshold to avoid
configuration mistakes.
 You can successfully run this
command only if the NCMU works
properly.
The configuration takes effect
immediately after the parameter is
modified.
The value of the Low Temperature
Critical Point must be smaller than that
Not involved of the High Temperature Critical Point.
This command is applicable to only the
NCMU of the direct-ventilation type
and that with a ventilation film.
This command can be run successfully
for the NCMU in the auxiliary power
system of the RRU only when the
power system is the APM30.

You can successfully run this

command only if the NCMU works
properly.
The configuration takes effect
immediately after the parameter is
modified.
The value of the Heater Start
Temperature must be smaller than that
of the Heater Close Temperature.
The value of the Heater Close
Temperature should not be set too
Not involved large. Otherwise, the heat dissipation
of the system will be affected.
This command can be run successfully
for the NCMU in the auxiliary power
system of the RRU or BBU only when
the power system is the APM30.
It is recommended that you obtain the
current heater parameter values by
running the LST HTPA command
before setting the threshold to avoid
configuration mistakes.

There must be a gap of no less than

Not involved 5% between the upper limit and the
lower limit of the humidity.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

This parameter indicates the maximum

length of the FP before multiplexing.
Not involved The FP can be multiplexed only when
its frame length is smaller than this
value.

The parameter modification has no

Not involved
impact on the equipment.
 The RRU IF offset is usually set by
users in network planning. In general,
it is recommended that this command
The service is affected until the RRU
be not run by users.
Chain configuration is correct
The RRU IF offset value takes effect
immediately after the parameter is
modified.

The parameter modification has no

Not involved
impact on the equipment.

Delay is introduced when the traffic is

Not involved
not busy.

If this switch is enabled, system will

Not involved detect Transmission Link Fault and try
to recover it.
When a port connects to an upper
node such as RNC or upper NodeB,
this port should be set as
RECOVEDRX, while the port of the
Not involved upper node should be set as EXT8K.
When a port connects to a lower node,
it should be set as EXT8K, while the
port of the lower node should be set as
RECOVEDRX.
 The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The service is interrupted if the

The service is affected until the
[PARA]CBS[/PARA] value is set too
configuration is correct.
small.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The service is affected until the The value of this parameter must be
configuration is correct. smaller than the physical interface rate.
The service is affected until the The value of this parameter must be
configuration is correct. smaller than the physical interface rate.

The service is affected until the This parameter must be consistent with
configuration is correct. the peer Ethernet interface.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

This parameter must be consistent with

The service is affected until the
the [PARA]FRAME[/PARA] parameter
configuration is correct.
of the peer E1/T1 interface.

The available bandwidth of service is

The service is affected until the affected when [PARA]Function[/PARA]
configuration is correct. is set to ENABLE and
[PARA]ULCIR[/PARA] is set too small.
 If a clock source exists and the clock
mode is set to FREE, the clock source
is invalid and the clock works in free-
run mode.
The system clock works in free-run
mode when the clock source is faulty.
After the reference clock source is
restored, the NodeB uses the clock
source.
Ensure that the clock source is
available before running the command.
If the system uses the IP clock source,
the IP clock source can be configured
to automatic or manual mode. In
automatic IP mode, the IP source link
in a normal state and with a high
priority will be chosen as the clock
Not involved
source. In manual IP mode, the
cabinet number, subrack number, slot
number, and IP link number are
required, and they can be configured
successfully.
The command cannot be run when the
clock quality test is being performed.
If the system responds with a "Clock
source is unavailable" message after
you run the command, do as follows:
For the LINE clock source, check
whether the LINE clock is configured
through the DSP LNKSRC command.
If not, add the LINE clock source
through the ADD LNKSRC command.
For the GPS card clock source, check
whether the GPS is configured through

The service is affected until the This parameter must be consistent with
configuration is correct. that of the peer Ethernet interface.
 The service is affected when the
The service is re-established only when
[PARA]LM[/PARA] is set to REMOTE
the loop is cancelled.
or LOCAL.

The loop back mode can be

overwritten. The command only takes
effect with the IP packets of the UDP
The service is re-established only when
protocol. This command cannot be
the loop is cancelled.
executed with IP tracing at the same
time. Some services may be
interrupted.

The parameter modification has no

Not involved
impact on the equipment.

If the switch is set to ON, it is

recommended that you run the LST
Not involved VSWRLIMIT to query the current
VSWR limit before setting the VSWR
limit.

The parameter modification has no

Not involved
impact on the equipment.

When you set the alarm limit of the

NEMU, do not need to enter the value,
Not involved
because the recovered limit is
automatically set by the system.
 The service is affected when the
The service is re-established only when
[PARA]LM[/PARA] is set to REMOTE
the loop is cancelled.
or LOCAL.

This parameter must be consistent with

The service is affected until the
[PARA]LNCODE[/PARA] of the peer
configuration is correct.
E1/T1 interface.

This parameter must be consistent

The service is affected until the
with [PARA]LNCODE[/PARA] of the
configuration is correct.
peer E1/T1 interface.

The service is re-established only when The parameter modification has no

the loop is cancelled. impact on the equipment.
 The service based on the
The service is re-established only when
[PARA]PEERIP[/PARA] will be
the loop is cancelled.
interrputed.

The scrambling mode that has been

set must be consistent with the E1
The service is affected until the
supported. If [PARA]LNCODE[/PARA]
configuration is correct.
of the E1 supported is set to AMI, you
must use the scrambling mode.

The service is affected until the This parameter must be consistent with
configuration is correct. that of the peer ethernet interface.

The parameter modification has no

Not involved
impact on the equipment.

The service is affected until the The user data carried on this port will
configuration is correct. be interrupted.

The data stream on the user plane can

be classified as different service
The service is affected until the classes among the user data types
configuration is correct. according to the DSCP values, and
the classification corresponds to
different VLAN settings.

The service is affected until the The parameter modification has no

configuration is correct. impact on the equipment.
Not involved This parameter cannot be modified.

The service is affected until the This parameter must be consistent with
configuration is correct. that of the peer Ethernet interface.

The service is affected until the This parameter must be consistent with
configuration is correct. that of the peer Ethernet interface.

The service is affected until the This parameter must be consistent with
configuration is correct. that of the peer Ethernet interface.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The value is valid only when the LSDF

Not involved
is set to ENABLE.

Not involved This parameter cannot be modified.

 You can successfully run this
command only if the NCMU works
properly.
The configuration takes effect
immediately after the parameter is
modified.
The value of the Low Temperature
Critical Point must be smaller than that
Not involved of the High Temperature Critical Point.
This command is applicable to only the
NCMU of the direct-ventilation type
and that with a ventilation film.
This command can be run successfully
for the NCMU in the auxiliary power
system of the RRU only when the
power system is the APM30.

The parameter modification has no

Not involved
impact on the equipment.
 You can successfully run this
command only if the NCMU works
properly.
The configuration takes effect
immediately after the parameter is
modified.
The value of the Over Temperature
Threshold must be larger than that of
the Low Temperature Threshold.
The two temperature thresholds
correspond to the following two
temperature alarms respectively:
Over Temperature Threshold: the over
temperature alarm is reported when
Not involved the actual temperature exceeds the
Over Temperature Threshold.
Low Temperature Threshold: the low
temperature alarm is reported when
the actual temperature is lower than
the Low Temperature Threshold.
This command can be run successfully
for the NCMU in the auxiliary power
system of the RRU only when the
power system is the APM30.
It is recommended that you obtain the
current threshold values by running the
LST TATH command before setting the
threshold to avoid configuration
mistakes.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

If the SASU works in bypass mode, it

Not involved does not support tower-mounted
amplification

The parameter modification has no

Not involved
impact on the equipment.
 If a clock source exists and the clock
mode is set to FREE, the clock source
is invalid and the clock works in free-
run mode.
The system clock works in free-run
mode when the clock source is faulty.
After the reference clock source is
restored, the NodeB uses the clock
source.
Ensure that the clock source is
available before running the command.
If the system uses the IP clock source,
the IP clock source can be configured
to automatic or manual mode. In
automatic IP mode, the IP source link
in a normal state and with a high
priority will be chosen as the clock
Not involved
source. In manual IP mode, the
cabinet number, subrack number, slot
number, and IP link number are
required, and they can be configured
successfully.
The command cannot be run when the
clock quality test is being performed.
If the system responds with a "Clock
source is unavailable" message after
you run the command, do as follows:
For the LINE clock source, check
whether the LINE clock is configured
through the DSP LNKSRC command.
If not, add the LINE clock source
through the ADD LNKSRC command.
For the GPS card clock source, check
whether the GPS is configured through

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

 This parameter cannot be modified
when the logical cell exists; The
maximum transmit power of the local
Not involved
cell must stay within the value range
supported by the power amplifier;
otherwise, the local cell is unavailable.

It only takes effect on the new user

after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.

A string of up to 31 characters can be

entered. The string cannot be all
blanks, or contain characters such as
Not involved '&lt;', '&gt;', '!', '?', '^', two or more
spaces, or two or more percentage
symbols (%). It is recommended you
name the NodeB after the place.

The output ports only exist on the

Not involved
NEMU.

Adjusting the downtilt of the RET

antenna may affect the antenna
coverage.
Ensure that you have calibrated the
RET antenna before setting the
downtilt of the antenna through the
CLB ANT command.
The tilt range supported by the RET
antenna varies with models and
vendors. It is recommended that you
Not involved list the tilt range supported by the
antenna through the LST
ANTTILTRNG command before
adjusting the tilt.
It takes up to three minutes to set the
tilt of an RET antenna.
For the single polarization RET
antenna, ensure that the two RET
antennas connected to the
ANT_Tx/RxA and ANT_RxB
connectors have the same tilt.
 A string of up to 31 characters can be
entered. The string cannot be all
Not involved blanks or all '\'s, or contain the
characters such as ">", "<", "!", "?",
";", """, "'", or ", ".
A string of up to 31 characters can be
entered. The string cannot be all
Not involved blanks or all '\'s, or contain the
characters such as ">", "<", "!", "?",
";", """, "'", or ", ".

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.
 It only takes effect on the new user
Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

 You can successfully run this
command only if the NCMU works
properly.
The configuration takes effect
immediately after the parameter is
modified.
The value of the Low Temperature
Critical Point must be smaller than that
Not involved
of the High Temperature Critical Point.
This command is applicable to only the
NCMU of the direct-ventilation type
and that with a ventilation film.
This command can be run successfully
for the NCMU in the auxiliary power
system of the RRU only when the
power system is the APM30.

You can successfully run this

command only if the NCMU works
properly.
The configuration takes effect
immediately after the parameter is
modified.
The value of the Low Temperature
Critical Point must be smaller than that
Not involved
of the High Temperature Critical Point.
This command is applicable to only the
NCMU of the direct-ventilation type
and that with a ventilation film.
This command can be run successfully
for the NCMU in the auxiliary power
system of the RRU only when the
power system is the APM30.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

The output ports only exist on the

Not involved
NEMU.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

You can successfully run this

command only if the NCMU works
properly.
The configuration takes effect
immediately after the parameter is
modified.
The value of the Over Temperature
Threshold must be larger than that of
the Low Temperature Threshold.
The two temperature thresholds
correspond to the following two
temperature alarms respectively:
Over Temperature Threshold: the over
temperature alarm is reported when
Not involved the actual temperature exceeds the
Over Temperature Threshold.
Low Temperature Threshold: the low
temperature alarm is reported when
the actual temperature is lower than
the Low Temperature Threshold.
This command can be run successfully
for the NCMU in the auxiliary power
system of the RRU only when the
power system is the APM30.
It is recommended that you obtain the
current threshold values by running the
LST TATH command before setting the
threshold to avoid configuration
mistakes.
Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.
 The output ports only exist on the
Not involved
NEMU.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

 The parameter modification has no
Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

 Use this command to add a destination
port which is a FTP server port
providing FTP services. The port is
Not involved
corresponding to a FTP server ip
address. The max number of list is
twenty.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

If the position of the RRU is TRUNK,

you can infer that the position of the
RRU is in the main chain or ring. If the
Not involved position of the RRU is BRANCH, you
can infer that the position of the RRU is
in a parent RRU. All parent RRUs refer
to the RHUB.
 If the ALD system type is Custom, the
value can be set to R0A, R0B, and
RET_PORT. If the ALD system type is
Not involved RET_ONLY_MULTICORE, the value
can be only set to RET_PORT. In other
cases, the value can be set to R0A
and R0B.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

An auxiliary power system can supply

Not involved power to multiple RRUs. One RRU
controls this auxiliary power system.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

 The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

It only takes effect on the new user

after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.

The parameter modification has no

Not involved
impact on the equipment.
 This command can be run only when
the RRU corresponding to the
specified antenna connector works
properly. The modification takes effect
immediately after the command is run.
If the Single-Antenna Remote
Electrical Tilt (SINGLE-RET), Multi-
Antenna Remote Electrical Tilt
(MULTI_RET), Smart Tower-Mounted
Amplifier (STMA), or Same Band
Antenna Sharing Unit (SASU) is used,
you should set the ALD power switch
to ON. During the operation, the
system may automatically set the
switch of the antenna connector to
OFF due to the ALD current abnormal
alarm. For details, refer to ALM-1319
Not involved
RRU ALD Current Abnormal.
The ALD power switches for ports
labeled R0A and RET_PORT on the
RRU cannot be set to ON at the same
time. Otherwise, the system responds
with an "Execution failed" message.
When the ALD power switch is set to
ON, you need to set the current alarm
threshold of that port. The ALD current
alarm thresholds vary with the ALD
system types and connections, as
listed in the following table:
The ALD system type can be
categorized into the undercurrent alarm
occurrence threshold (mA), the
undercurrent alarm clearance threshold
(mA), the overcurrent alarm
The modified parameters take effect
immediately; When the NodeB works
in four-way antenna mode, it does not
support the cell radius larger than 30
Not involved km; When the logical cell exits, you
cannot make dynamic modification to
the cell radius when the cell radius
changes between equal to or smaller
than 30 km and larger than 30 km.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The remote cell group to be modified

must exist; It contains a string of up to
31 bytes.
The string should not be totally blanks
Not involved
or contain the following characters: ' &lt
', ' &gt ', ' ! ', '?', ' ' ', ' " '. In addition
it will be ignored if the end of the string
is "\".

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

A string of up to 31 characters can be

entered. The string cannot be all
Not involved blanks or contain the following
characters such as ">", "<", "!", "?",
";", """, "'", ", ", or "\".

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.
 To specify the RRUs for a local cell in
the distributed sector, you may
repeatedly execute the command;
Not involved when you remove the ending RRU
from the cell, the command fails to be
executed.

Not involved This parameter cannot be modified.

It only takes effect on the new user

after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

It only takes effect on the new user

after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.

The parameter modification has no

Not involved
impact on the equipment.
Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

This parameter can be successfully

modified only when the logical cells are
not set up. After this parameter is
Not involved
modified, all cells in the NodeB are set
up again according to the new
resource allocation mode.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

The type of the sub-board can be

Not involved modified only if the sub-board is
removed.
Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 It only takes effect on the new user
after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.
 It only takes effect on the new user
Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Use this command to add a destination

port which is a FTP server port
providing FTP services. The port is
Not involved
corresponding to a FTP server ip
address. The max number of list is
twenty.

Not involved This parameter cannot be modified.

 After you set an alarm to be shielded,
the NodeB handles the alarm
according to its current status. If the
alarm exists at that time, the NodeB
generates the alarm occurrence report.
Then, when the alarm is cleared
manually, the NodeB generates the
alarm clearance report. If the alarm
does not exist at that time, the NodeB
does not generate the alarm
occurrence report or clearance report.
When you set an alarm to be
unshielded, the NodeB handles the
Not involved alarm according to its current status. If
the alarm exists at that time, the
NodeB generates the alarm occurrence
report. If the alarm does not exist at
that time, the NodeB does not
generate any report.
After you set an alarm to be
unshielded, the NodeB handles the
alarm in a normal way. If the alarm is
generated, the NodeB generates the
alarm occurrence report. If the alarm is
cleared, the NodeB generates the
alarm clearance report.

Not involved This parameter cannot be modified.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

It only takes effect on the new user

after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.
 The parameter modification has no
Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.
Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Among the input parameters, the

following ones must be entered in
compliance with the sensor
specifications: Sensor Output Upper
Not involved Limit, Sensor Output Lower Limit,
Measurement Upper Limit, and
Measurement Lower Limit. Otherwise,
such serious faults as incorrect
monitoring values may occur.
 Among the input parameters, the
following ones must be entered in
compliance with the sensor
specifications: Sensor Output Upper
Not involved Limit, Sensor Output Lower Limit,
Measurement Upper Limit, and
Measurement Lower Limit. Otherwise,
such serious faults as incorrect
monitoring values may occur.

Among the input parameters, the

following ones must be entered in
compliance with the sensor
specifications: Sensor Output Upper
Not involved Limit, Sensor Output Lower Limit,
Measurement Upper Limit, and
Measurement Lower Limit. Otherwise,
such serious faults as incorrect
monitoring values may occur.

Among the input parameters, the

following ones must be entered in
compliance with the sensor
specifications: Sensor Output Upper
Not involved Limit, Sensor Output Lower Limit,
Measurement Upper Limit, and
Measurement Lower Limit. Otherwise,
such serious faults as incorrect
monitoring values may occur.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

This parameter cannot be modified

Not involved
when the logical cell exists.
 When the encryption mode for
transmission is set to AUTO, the FTP
client tries to transmit data in
encryption mode first. If the
transmission fails, the FTP client
transmits data in plain text mode.
If the FTP client is set to support
Not involved firewalls, the FTP client sends the
CCC command to switch the data
transmitted in the control command
channel to plain text.
After this command is run successfully,
the settings take effect in the next FTP
operation.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved None

Not involved This parameter cannot be modified.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.
Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter can not be modified.

Not involved This parameter cannot be modified.

Not involved This parameter can not be modified.

Not involved This parameter cannot be modified.

Not involved This parameter can not be modified.

Not involved This parameter cannot be modified.

Not involved This parameter can not be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

 The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Adjusting the downtilt of the RET

antenna may affect the antenna
coverage.
Ensure that you have calibrated the
RET antenna before setting the
downtilt of the antenna through the
CLB ANT command.
The tilt range supported by the RET
antenna varies with models and
vendors. It is recommended that you
Not involved list the tilt range supported by the
antenna through the LST
ANTTILTRNG command before
adjusting the tilt.
It takes up to nine minutes to set the tilt
of an RET antenna.
For the single polarization RET
antenna, ensure that the two RET
antennas connected to the
ANT_Tx/RxA and ANT_RxB
connectors have the same tilt.
The site to be modified must exist; It
contains a string of up to 31 bytes.
The string should not be totally blanks
Not involved or contain the following characters: ' &lt
', ' &gt ', ' ! ', '?', ' ' ', ' " '. In addition
it will be ignored if the end of the string
is "\".
Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.
Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

The delayed discharge test time has a

Not involved direct impact on power-off test, timing
test and manual background test.
 Adjusting the downtilt of the RET
antenna may affect the antenna
coverage.
Ensure that you have calibrated the
RET antenna before setting the
downtilt of the antenna through the
CLB ANT command.
The tilt range supported by the RET
antenna varies with models and
vendors. It is recommended that you
Not involved list the tilt range supported by the
antenna through the LST
ANTTILTRNG command before
adjusting the tilt.
It takes up to 11 minutes to set the tilt
of an RET antenna.
For the single polarization RET
antenna, ensure that the two RET
antennas connected to the
ANT_Tx/RxA and ANT_RxB
connectors have the same tilt.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

There must be a gap of no less than

Not involved 3°C between the upper limit and the
lower limit of the temperature
 You can successfully run this
command only if the NCMU works
properly.
The configuration takes effect
immediately after the parameter is
modified.
The value of the Low Temperature
Critical Point must be smaller than that
Not involved
of the High Temperature Critical Point.
This command is applicable to only the
NCMU of the direct-ventilation type
and that with a ventilation film.
This command can be run successfully
for the NCMU in the auxiliary power
system of the RRU only when the
power system is the APM30.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

For details on the value range, refer to

<a href="BTS3836-
Not involved
CABINET.htm">Subrack Information
Table</a>.

The service is affected until the The parameter modification has no

configuration is correct impact on the equipment.

There must be a gap of no less than

Not involved 3°C between the upper limit and the
lower limit of the temperature

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

You can run this command only if the

specified RRU works properly.
Normally, the RRU TX unit is set to
ON. If you set the RRU TX unit to OFF,
the cell in this RRU cannot work
properly.
Not involved After you run this command to set the
RRU TX unit to ON in case that the
RRU TX unit is OFF, the TX
transmission channel of the RRU is
unavailable until the logical cell is set
up and the carrier frequency is
configured for the RRU.
Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

 Ensure that the transmission resource
group to be modified does exist, and
the bandwidth of the transmission
resource groups after modification
should not be greater than the
bandwidth of the physical port carrying
them. If the bearing type of the
transmission resource group is ATM,
the bandwidth of the transmission
resource groups after modification
should satisfy the bandwidth check.
The method to check the bandwidth is
as follows:
1. Suppose the bandwidth of the
Bearing Type physical port is A if the
AAL2 path does not join in the
configured transmission resource
Not involved
group, then SUM (bandwidth occupied
by all SAAL links carried on this
physical link (using SCR for calculation
in case of VBR)) + MAX (bandwidth
occupied by all AA2PATH carried on
this physical link (using PCR for
calculation))+ bandwidth occupied by
OM channel carried on this physical
link (using SCR for calculation in case
of VBR) <= A.
2. Suppose the bandwidth of
transmission resource group is A if the
AAL2 path joins in the configured
transmission resource group, then
SUM (bandwidth occupied by all SAAL
links carried on this physical link (using
SCR for calculation in case of VBR)) +
The parameter modification has no
Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 When you set the alarm limit of the
NEMU, do not need to enter the value,
Not involved
because the recovered limit is
automatically set by the system.

Modifying delay may affect normal

services of a cell. The heavier the load
in the cell is, the more obvious the
Not involved impact is; Test results indicate that the
change smaller than 300 ns in delay
shows no impact on the normal
services of the cell.

Modifying delay may affect normal

services of a cell. The heavier the load
in the cell is, the more obvious the
Not involved impact is; Test results indicate that the
change smaller than 300 ns in delay
shows no impact on the normal
services of the cell.

Modifying delay may affect normal

services of a cell. The heavier the load
in the cell is, the more obvious the
Not involved impact is; Test results indicate that the
change smaller than 300 ns in delay
shows no impact on the normal
services of the cell.

Modifying delay may affect normal

services of a cell. The heavier the load
in the cell is, the more obvious the
Not involved impact is; Test results indicate that the
change smaller than 300 ns in delay
shows no impact on the normal
services of the cell.
 This parameter cannot be modified
when the logical cell exists; The
downlink and uplink frequencies of the
local cell must stay within the same
frequency band; If the power amplify
unit can only support two carriers, then
in a Power Amplifier, the difference
between frequencies of local cells must
Not involved be greater or equal to
4.2MHz(21*0.2MHz), and be less or
equal to 5MHz(25*0.2MHz) ; If the
power amplify unit can support four
carriers, then in a Power Amplifier,
the difference between frequencies of
local cells must be greater or equal to
4.2MHz(21*0.2MHz), and be less or
equal to 15MHz(75*0.2MHz).

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.
Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

The parameter modification has no

Not involved
impact on the equipment.

The parameter modification has no

Not involved
impact on the equipment.
 The parameter modification has no
Not involved
impact on the equipment.

No involved None

No involved None

No involved None
No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None
No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None
No involved None

No involved None

If two clock links of the PTP protocol

are configured, the two clock links
No involved
must be in the same slot with the same
client address and domain value.

This parameter is affective when link

No involved
type is 1588 clock link.

Before the secondary homing

No involved NCP/CCP is added, the corresponding
primary homing NCP/CCP must exist.

The maintenance domain name must

No involved
be unique in one equipment.

No involved None

The maintenance domain name must

No involved
be unique in one equipment.

The maintenance association name

No involved must be unique in one maintenance
domain.

VLAN must be mapped with the

No involved
maintenance association.

No involved Only in VLAN

No involved Only in VLAN

No involved A string of 12 characters is required

One RMEP can be assigned with up to

four IP addresses. The assigned IP
No involved
address cannot be in conflict with the
local IP address.
Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved None

Not involved None

Not involved None

Not involved .

Not involved None

Not involved None

Not involved None

Not involved None

Not involved None

Not involved None

Not involved None

Not involved None

Not involved None

 It only takes effect on the new user
after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.

It only takes effect on the new user

after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.

It only takes effect on the new user

after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.

It only takes effect on the new user

after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.

It only takes effect on the new user

after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.

It only takes effect on the new user

after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.

It only takes effect on the new user

after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.
 It only takes effect on the new user
after the parameter is set, and the old
users use the old parameter. To modify
Not involved
the Mac-hs scheduling parameters of
the specified local cell, ensure that the
local cell supports HSDPA.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

It only takes effect on the new user

Not involved after the parameter is set, and the old
users use the old parameter.

None None

None None

None None

None None

None None

None This parameter cannot be modified.

None This parameter cannot be modified.

No involved None

No involved None

No involved None

No involved None
No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None

No involved None
No involved None

No involved None

No involved None

No involved None

No involved None

No involved This parameter cannot be modified.

No involved This parameter cannot be modified.

No involved This parameter cannot be modified.

No involved This parameter cannot be modified.

No involved This parameter cannot be modified.

No involved This parameter cannot be modified.

No involved This parameter cannot be modified.

No involved This parameter cannot be modified.

No involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

No involved Only in VLAN

Not involved This parameter cannot be modified.

Not involved This parameter cannot be modified.

Not involved None

Not involved None

Not involved None

Not involved None

Not involved None

Not involved None

None This parameter cannot be modified.

Not involved None

Validation of Modification Impact on Radio Network Performance Introduced in Version…

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the It will affect the transffers-rate.
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.1
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.1
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.2
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.3
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The board should be reset to

Versions earlier than
make the modified parameter None
RAN11.0
valid.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the It will affect the transffers-rate.
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the It will affect the transffers-rate.
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
The parameter modification
Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.

The parameter modification

has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.
The parameter modification
has no impact on the None RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.

The parameter modification

Versions earlier than
has no impact on the None
RAN11.0
equipment.
Attribute

Radio

Radio

Radio

Radio

Radio

Radio

Radio

Radio

Transport

Equipment
Equipment

Equipment

Transport

Transport

Equipment

Radio
Equipment

Equipment

Equipment

Transport

Equipment
Equipment

Radio

Equipment

Equipment
Equipment

Radio

Equipment

Equipment
Equipment

Equipment

Equipment

Equipment
Equipment

Equipment

Transport
Equipment

Equipment

Equipment

Equipment

Transport
Equipment

Radio

Transport

Equipment

Equipment

Equipment

Equipment

Equipment
Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment
Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment
Equipment

Equipment

Transport

Transport

Transport

Transport

Equipment

Equipment
Equipment

Equipment

Transport

Equipment
Equipment

Transport

Equipment

Equipment
Transport

Equipment

Equipment

Equipment

Equipment
Equipment

Transport

Equipment

Transport

Transport

Equipment
Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Transport

Transport
Transport

Transport

Transport
Equipment

Equipment
Equipment

Equipment

Equipment
Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Radio

Radio

Equipment
Radio

Equipment

Transport
Transport

Radio

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment
Equipment

Radio

Radio

Equipment

Radio

Radio

Radio
Equipment

Equipment

Equipment
Equipment

Equipment

Radio

Transport

Transport
Equipment

Equipment

Equipment

Equipment

Radio

Radio

Radio

Transport
Radio

Radio

Equipment

Equipment

Equipment
Equipment

Radio

Equipment

Equipment

Transport

Equipment

Equipment
Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Transport

Equipment

Equipment
Transport

Transport

Transport

Transport

Equipment

Equipment
Equipment

Equipment

Equipment

Transport

Equipment

Equipment

Equipment
Equipment

Equipment

Transport

Transport

Transport

Transport

Radio
Radio

Radio

Radio

Radio

Transport
Equipment

Equipment

Equipment

Equipment

Equipment

Equipment
Equipment

Equipment

Transport

Transport

Equipment
Equipment

Equipment

Equipment

Equipment

Transport

Transport
Transport

Transport

Equipment

Equipment

Equipment

Transport

Transport
Transport

Transport

Transport

Transport

Transport
Transport

Transport

Equipment

Equipment

Equipment

Equipment

Equipment
Equipment

Equipment

Radio

Radio

Equipment

Radio

Equipment

Equipment

Equipment
Equipment

Equipment
Equipment

Equipment

Equipment

Equipment
Transport

Transport

Transport
Equipment

Transport

Transport

Transport

Transport
Transport

Equipment

Transport

Transport

Equipment

Equipment

Transport
Transport

Transport

Equipment

Equipment

Transport

Transport
Equipment

Transport
Transport

Transport

Equipment

Equipment

Equipment

Equipment
Transport

Transport

Transport

Transport
Transport

Transport

Transport

Equipment

Transport

Transport

Transport
Radio

Transport

Transport

Transport

Equipment

Equipment

Equipment

Transport
Equipment

Equipment
Equipment

Radio

Transport
Transport

Transport

Radio

Transport

Transport

Transport

Radio

Transport

Transport

Transport
Transport

Transport

Radio

Transport

Radio

Equipment

Transport

Equipment

Equipment
Equipment

Equipment

Equipment
Transport

Transport

Transport

Transport

Transport

Equipment

Transport
Radio

Radio

Equipment

Equipment

Equipment
Equipment

Equipment

Transport

Transport

Transport

Transport

Transport
Transport

Transport

Radio

Radio

Radio

Radio
Radio

Radio

Radio

Radio

Transport

Transport
Equipment

Equipment

Equipment

Equipment

Equipment
Equipment

Transport

Equipment

Equipment

Equipment

Equipment

Equipment
Equipment

Equipment
Transport

Transport

Transport

Transport

Transport
Transport

Transport

Transport

Transport

Transport

Transport
Transport

Transport

Transport

Equipment

Equipment

Transport

Transport

Equipment
Equipment

Equipment

Equipment

Equipment
Equipment

Equipment

Equipment

Equipment

Equipment

Transport
Equipment

Transport

Transport

Transport

Transport

Transport

Equipment

Equipment
Equipment

Equipment

Equipment

Equipment

Equipment

Transport
Equipment

Equipment

Radio

Radio
Equipment

Radio

Equipment

Transport
Radio

Radio

Transport

Equipment

Equipment

Equipment

Equipment

Radio

Radio

Equipment

Transport

Equipment
Equipment

Equipment

Radio

Transport

Transport

Radio

Equipment
Transport

Transport

Equipment

Transport

Equipment

Transport

Equipment

Transport

Equipment
Equipment

Equipment

Transport

Transport

Transport

Transport

Equipment

Equipment
Equipment

Equipment

Equipment
Radio

Radio

Radio

Transport

Transport

Transport

Transport

Transport

Transport

Equipment
Equipment

Equipment

Equipment

Transport

Equipment

Equipment

Transport

Equipment

Equipment
Equipment

Radio

Radio

Radio

Radio

Radio
Radio

Radio

Radio

Equipment

Equipment

Equipment

Radio
Equipment

Transport

Radio

Transport

Equipment

Radio
Equipment

Equipment
Equipment

Equipment
Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment
Equipment

Equipment

Equipment

Equipment

Transport

Radio
Equipment

Equipment

Equipment

Equipment
Equipment

Transport

Equipment

Equipment

Equipment

Equipment

Equipment

Transport
Transport

Transport

Radio

Equipment
Equipment

Equipment
Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment
Transport

Transport

Transport

Transport

Transport
Equipment

Equipment

Transport

Equipment

Equipment

Equipment
Transport

Transport

Equipment

Equipment

Transport

Equipment
Transport

Equipment

Radio

Equipment

Transport

Equipment

Equipment

Transport

Equipment
Equipment

Equipment

Equipment
Transport

Transport

Transport

Equipment
Equipment

Radio

Equipment

Equipment

Equipment

Transport
Transport

Transport

Equipment

Equipment

Equipment

Equipment

Transport

Transport
Transport

Transport

Transport

Equipment

Equipment
Transport

Transport
Transport

Equipment

Equipment

Equipment
Equipment

Equipment

Equipment

Equipment

Equipment
Radio

Equipment

Equipment

Transport

Transport

Equipment

Equipment

Equipment
Transport

Transport

Equipment
Transport

Transport

Transport

Transport

Transport

Transport

Transport

Transport
Transport

Transport

Transport

Equipment

Equipment
Equipment

Equipment

Equipment

Equipment
Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment
Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment
Equipment

Transport

Transport

Transport

Transport

Transport

Transport

Transport

Transport

Transport

Transport

Transport

Transport

Transport
Transport

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Transport
Radio

Radio

Radio

Radio

Radio

Radio

Radio
Radio

Radio

Radio

Radio

Radio

Radio

Radio

Radio

Radio

Radio

Equipment

Equipment

Equipment

Equipment
Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment

Equipment
Equipment

Equipment

Equipment

Equipment

Equipment

Transport

Transport
Transport

Transport
Transport

Transport
Transport

Transport

Transport

Transport

Transport

Transport

Transport

Transport

Transport

Transport

Transport

Equipment
Equipment

Equipment

Transport

Transport

Transport

Transport

Transport

Transport

Equipment