Scribd
Upload
130 views7 pages

NEC - Programmer Manual

This document provides instructions for using an NEC programmer to generate keys and modify electronic control units for various Mercedes models from years prior to 2000. It outlines the following steps: 1. Choose the EIS type and load necessary dumps from the EIS, ECU, ESL or ESM modules. 2. Generate keys for the ignition and save the key dumps. 3. Modify the dumps on the EIS and other control modules and save the modified dumps. 4. Use the NEC programmer software to program the keys and load the modified dumps onto the appropriate control modules.

Uploaded by

Nidal Kourbage
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
130 views7 pages

NEC - Programmer Manual

This document provides instructions for using an NEC programmer to generate keys and modify electronic control units for various Mercedes models from years prior to 2000. It outlines the following steps: 1. Choose the EIS type and load necessary dumps from the EIS, ECU, ESL or ESM modules. 2. Generate keys for the ignition and save the key dumps. 3. Modify the dumps on the EIS and other control modules and save the modified dumps. 4. Use the NEC programmer software to program the keys and load the modified dumps onto the appropriate control modules.

Uploaded by

Nidal Kourbage
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

NEC_ programmer Manual

1- EIS type
2- use offset buffer ( ETL ) - ( Xprog )
3- Load EIS dump
4- ECU type
5- Load ECU dump
6- Load ESL or ESM dump
7- access Ir Programmer for big plastic key .
8- access Ir Programmer for RENEW key function .
9- save EIS dump (option )
10- save ECU dump (option )
11- save ESL or ESM dump (option )
12- access Ir Programmer for Chrom key
13- ( select to generate)- ( don't generate )
14- Process ( generate select keys/modify all loading dumps )
15- access Ir Programmer for small plastic key .
16- ( generate keys dumps for Ir Programmer use)- ( generate keys
dumps for NEC_Programmer.
How use it

Exampel for W210 /W202 /W208/W220


All type under year 2000 need only to modify (EIS and ESL for 210) and(EIS and
ESM for W220)
First we have to read 2 mcu from EIS / ESL or ESM and save both as BIN file

W220

W210
choose EIS type

1- load EIS mcu1


load ESL ESL1 or ESM chip93c56

SSID and Pass appear

choose key to generate we choose as exampel key 5/6/7/8


press Process

Files Have Been Save message appear to infom thats


Mcu1 and ESL1 had modify and save in same folder and key
5/6/7/8 had generate and save in same folder
2- load EIS mcu2 and ESL2 choose key 5/6/7/8 thin
press Process
Files Have Been Save message appear to infom thats
Mcu2 and ESL2 had modify and save in same folder

Write all modify dumps to chip and mcu


Now we have end from modify dumps and generate keys .
MCU Programming
Run NEC_Prog.exe
NEC_Prog dialoge appear select COM port as USB convert statu

Message ( Hardware OK ) must appear . if no't check USB cabel or you have
select error port .
press (load,BIN )then load BIN key file from folder .

After we insert MCU in ZIF socket press programming

MCU Programming And Verfying Is OK ,must appear at box message .


Solder MCU to PCB .
insert key into EIS , key LED on thin off thats mean key programming is
OK ,and you can run the car .

You might also like