Scribd
Upload
105 views

HVP 20 Error Code en

The document provides error codes, causes, and troubleshooting steps for issues with an HVP-20 sewing machine. Some key errors include: - ER0.1: Power module error or overcurrent/voltage issue - check power module or board - ER0.4: High voltage error when turning on - check power voltage or resistors/fuses - ER0.7: Motor connection, sensor, or object stuck issues - check motor, sensors, pulley - ER0.8: Communication error between control box and CPU - check operation box - ER0.9: Solenoid short or transistor fault - check solenoids, transistors - ER0.11: Auto needle up

Uploaded by

hanif khan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
105 views

HVP 20 Error Code en

The document provides error codes, causes, and troubleshooting steps for issues with an HVP-20 sewing machine. Some key errors include: - ER0.1: Power module error or overcurrent/voltage issue - check power module or board - ER0.4: High voltage error when turning on - check power voltage or resistors/fuses - ER0.7: Motor connection, sensor, or object stuck issues - check motor, sensors, pulley - ER0.8: Communication error between control box and CPU - check operation box - ER0.9: Solenoid short or transistor fault - check solenoids, transistors - ER0.11: Auto needle up

Uploaded by

hanif khan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

HVP-20 ERROR CODE

Error Code Cause of the Problem Status and Measurement


Motor and machine will be shutting down.
1. Power module detected error.
ER0.1 Please check the power module.
2. Abnormal over current or voltage occurred..
Please check the power board over current circuitry.
Motor and machine will be shutting down.
Please check the AC power. (Too high)
＊If control box is AC 220V system, don’t use the AC 380V power voltage,
1. When power on, detected high voltage
otherwise the LCD will display ER0. 4 after 2 second of power ON. If continue
2. Connect the wrong voltage or supply power is too high.
ER0. 4 3. Aluminum casing resistor for the brake circuit is defective or power supply the 380V power, the electrolytic capacitors (C8,C9,C70) of power board
board F1 fuse burst. will burst open over a period of time and cause the fuses (F1,F2) of EMI board
open circuit.
Please check the power board.
Please check the aluminum casing resistor and power board F1 fuse.
Motor and machine will be shutting down..
1. When power on, detected low voltage
ER0. 5 2. Connect the wrong voltage or supply power is too low..
Please check the AC power. (Too low)
Please check the power board.

1. Bad connection at the motor connector. Motor and machine will be shutting down.
2. Synchronizer (sensor) signal error. Please check the motor or motor connectors’ connection.
ER0. 7 3. Machine locked or object stuck in the motor pulley. Please check the synchronizer (sensor) and its signal.
4. Sewing material is too thick. Please check machine head to see if objects stuck in the motor pulley, or rotate not smoothly.

Motor and machine will be shutting down.


ER0. 8 Operation box linked to CPU interface had communication error
Please check the operation box.

Motor still can run, but all output signals and operation box’s pattern sewing function will be invalid..
1. Machine solenoid shorted.
ER0. 9 2. Main board’s power transistor is faulty.
Please check machine’s solenoids or the resistance value is 2 Ω less.
Please check all the power transistors, which related to solenoid.

Motor and machine will be shutting down.


If parameter 【121.ANU】 is set ON, but auto needle up is malfunction Please check synchronizer’s up position’s signal.
ER0. 11 when the power turned on. Please check control box.
Please check machine head to see if objects stuck in motor pulley, or pulley rotate not smoothly.

Automatic starts the clutch mode.


Power on, no synchronizer signal or not connected (valid for under
ER0. 12 table motor)
If use direct-drive motor, please short the pin 4 and pin 5 of the CN18 on the main board.
If use under table motor, please check the synchronizer. (also check the connection and model)

Motor rotation icon in LED is halting and not moving. Motor stops.
1. Safety switch is either faulty or bad connection. (For interlock stitch Please check the safety switch.
. or blind stitch machine).
2. Parameter【075. SFM】setting not match the machine head model.
Please check parameter table on【075. SFM】 setting, make sure it match machine head’s
safety switch

You might also like