Scribd
Upload
156 views1 page

PIPEMILL - Piping Engineering, Design and Analysis

This document summarizes the results of a clamp connector design and analysis using Pipemill software. It provides input data for the hub, clamp, bolts, and loads. Intermediate design data and calculated stresses are presented for 9 stress categories. All stresses are below the allowable limits at both assembly and operating conditions, indicating the design is acceptable.

Uploaded by

fahid masood
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
156 views1 page

PIPEMILL - Piping Engineering, Design and Analysis

This document summarizes the results of a clamp connector design and analysis using Pipemill software. It provides input data for the hub, clamp, bolts, and loads. Intermediate design data and calculated stresses are presented for 9 stress categories. All stresses are below the allowable limits at both assembly and operating conditions, indicating the design is acceptable.

Uploaded by

fahid masood
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

PIPEMILL - Piping Engineering, Design and Analysis

Version: 4.00 PIPEMILL VERSION 4


Clamp Connector Design and Analysis to ASME VIII Div. 1 (2013) Appendix 24
____________________________________________________________________________________________________________

Calculation by: ____________________ Checked by: ______________________ Saturday,Nov 24,2018

File Name: C:\Users\SEF\Desktop\IvySoft_Pipemill_4.0_Downloadly.ir\IvySoft Pipemill 4.0\run_original\Demo-examples\V-4 CLAMP-ASME-01.clm


Project / Description: h hn T

Calculation details: 

Load case: Pressure only.  g2

INPUT DATA:
g0 g1
HUB: CLAMP: BOLTS:
N B C A
D = 273.05 mm Bc = 215.9 mm Bolt Dia Bd = 25.4 mm
A = 317.5 mm Cw = 88.9 mm Bolt Area Ab = 354.838 mm2
B = 234.95 mm Ci = 298.45 mm Bolts per lug= 2
N = 284.48 mm La = 23.09 mm Bc
T = 25.4 mm Lh = 50.8 mm LOADS: A
h = 25.4 mm lc = 15.24 mm Pressure = 96.526 bar G La
g0 = 19.050 mm Ct = 34.925 mm Longit. Moment = 0 kN.m
g1 = 24.765 mm GASKET: Axial force = 0 kN A
g2 = 16.510 mm Gasket OD = 260.35 mm
Ci/2
ca = 0 mm (corr. allw.) Gasket ID = 234.95 mm
Lh
Angle mu = 5 deg. Gasket 'y' = 124.1055 MPa
Angle phi= 15 deg. Gasket 'm' = 5.5
hn = 19.05 mm Thk. tg = 5.08 mm eb Neutral axis

ALLOW. STRESS: COLD (MPa) HOT (MPa)


C X
HUB: SA(h)= 137.895 SO(h)= 124.105
CLAMP: SA(c)= 155.132 SO(c)= 133.069
BOLTS: SA(b)= 172.368 SO(b)= 124.105
Cg Cw
INTERMEDIATE DESIGN DATA:
Dimensions: Load data:
b = 6.350 mm P = 96.526 barG. H = 4.64933 e+5 N. Ci lc Ct
C = 307.975 mm Peq= .000 barG. Hp = 5.24539 e+5 N. Section A-A
G = 247.650 mm Pd = 96.526 barG. Hm = 6.13101 e+5 N.

Code Forces Bolt Requirements: Moment Loads: Shear Loads:


Wm1 = 1.11138 e+5 N. Am1 = 447.8 mm2. Masm = 1.54278 e+7 Nmm. Qasm = 3.84618 e+5 N.
Wm2 = 1.42147 e+5 N. Am2 = 412.4 mm2. Mop = - 9.61664 e+5 Nmm. Qop = - 2.39745 e+4 N.
Wm3 = 2.29408 e+5 N. Am3 = 665.5 mm2. MHasm = 1.61385 e+7 Nmm.
Wop = 1.11138 e+5 N. Am = 665.5 mm2. MHop = - 1.00597 e+6 Nmm.
Wasm = 1.18512 e+5 N. Ab = 709.7 mm2.

Internal Moments Bolt Requirements: Shape factors:


MD = 1.0098 e+7 Nmm. MF = 1.1958 e+6 Nmm. g1/g0 = 1.300 f(act) = .685 - actual value
MG = - 1.2139 e+7 Nmm. MP = 7.5724 e+4 Nmm. h/h0 = .380 alpha = 12.68 deg.
MT = 1.549 e+6 Nmm. MR = - 1.7409 e+6 Nmm. f = 1.000 - used in calc.
__________________________________________________________________________________________________

CALCULATED STRESS:
Assembly Allowable Operating Allowable
MPa MPa MPa MPa
S1: Hub Longitudinal 193.519 206.843 8.648 186.158
S2: Hub Hoop Stress 0. 137.895 51.074 124.105
S3: Hub Axial Shear 33.798 110.316 65.424 99.284
S4: Hub Radial Shear 28.526 110.316 -1.778 99.284
S5: Clamp Longitudinal 87.794 232.698 169.946 199.604
S6: Clamp Tangential 130.81 232.698 122.671 199.604
S7: Clamp Lip Shear 40.339 124.106 78.087 106.455
S8: Clamp Lug Bending 35.785 155.132 33.558 133.069
S9: Contact Bearing 55.502 220.632 107.437 198.568
__________________________________________________________________________________________________

SUMMARY: Stresses Acceptable

You might also like