EVALUATION GEOLOGIST WORK

A. Daily Check

1. Update Daily DDR for Weekly Report

- Check daily DDR
- Change format DDR to Weekly Format
- Fill Intercept coal from Reconcile to Weekly Format
- Make sure Total Depth, Depth Log and Sublock are correct
- Make sure that true thickness multiply are correct for different Sub block
- Make a decision to get the Latest Hole Completed for Weekly Statistic

2. Core Summary and Reconcile Data

- Core Summary before Sampling
 Check for correct adjustment between Core, Geophysical Log and Final Adjustment.
 Check for parting and make a decision, Parting are stand alone sample or combine sample
 Core (Coal) minimum for Sampling are 30cm thick
 Parting minimum become stand alone sample are 10cm. If there are parting 9 -10cm MS, we can
sample it (become stand alone sample) but if Parting are Shaly or Coaly, we can combine it with Coal
 Make sure that the Hole have Completed Analysis (Exploration = Use Top and Bottom Coal) or
Limited Analysis (Infill = Coal)
 Get the correct Sample Coal

- Reconcile Data from Geos

 Check for Correlation using manual (Logging Data) or Minex Model
 Naming Seam from Correlation
 Check Core Summary (adjustment) must have same intercept on reconcile
 Make sure intercept coal used are from Final Adjustment
 Check for BOW, Log Basis, Depth Log, Run and Etc
 Make sure that Pilot Hole have coal thickness almost same as the Coring thickness
 Check reconcile for other Lithology
 Get final reconciled data and input it by Admin Database

3. Sample List Before and After Labelling

- Sample List before Labelling
 Check sample list with core summary from final adjustment intercept
 Cross check from reconciled data (make sure that sample list intercept coal have same data as
reconciled intercept)
 Cross check Lithology and parting data from reconciled data
 Numbering ID sample
 Sent the sample list to Project Geos

- Sample List after Labelling and Weight Measured

 Check labeling ID Sample
 Check for Weight sample (Usually coal have more weight than Roof or Floor Rock)
 Make request for analysis method
 Completed Analysis
 Top Coal = Proximate Analysis, Ash, TS, CV
 Coal = TM, Proximate, TS, CV, RD, HGI
 Bottom Coal = Proximate Analysis, Ash, TS, CV
 Limited Analysis
 Coal = TM, Proximate, TS, CV, RD, Na(Na2O), AFT Reducing
 EQM for each induvial seam, represent all working area
 Ash analysis

 Parting request analysis are = Ash, TS, CV

 Sent Sample to Sucofindo Lab
B. Weekly Check

1. Weekly Report Form

- Separate holes become Completed, Redrill and Pilot Hole
 Completed (Representative hole for statistic depth)
 Coring Hole (after pilot hole if any) in single location or
 Deepest Coring Hole (if any redrill coring hole)
 Grid pattern Open hole, but not as Pilot Hole
 Redrill/Failed (Unrepresentative hole for statistic depth)
 Failed hole (Geoph unlogged) or
 Shallower (redrill) coring hole compared to other coring hole in single location
 Pilot Hole
 Open Hole used as guide for Coring Hole in single location
- Get summary from Completed, Pilot Hole and Redrill
- Make a statistic drilling for a week and get the latest meter of drilling
- Send data intercept Coal to Supt.Exploration and Statistic data to Sr.Database

2. Minex Upadating Data

- Request MDB data for a Week (Access Database) to Sr.Database or Computing Geos
- Split MDB data into :
 Collar Data (From MDB to Excel with CSV format)
 Geology Data (From MDB to Excel with CSV format)
 Assay Data (From MDB to Excel with CSV format)
 Las Data still in the MDB data
 Copy Hole ID to Note Pad and save as Collar.dat
- Back up data Minex B31 until B35S and make a copy of it
- Load Collar (X, Y, Z, Final Depth, Azimuth, Dip, Type Hole)
- Load Sample Data
 Load Geology Data (Seamcode and Lithcode) with CSV format
 Load Assay Data (All assay are required) with CSV format
 Load Las Data (GR, LD, SD) with MDB format
- Check for Correlation and make a section Mount
- Naming Seam Layer
- Export new hole seam name into *.A33
- Sent to Sr.Resources Geos

3. A33 Cross Check from Sr.Resources Geos

- Get the Latest Model from Sr.Resources Geos
- Input Seam Layer Interval (A33) with Append processing
- Check Seam Name from the latest Correlation and Section

C. Monthly Check

1. Monthly Format
- Prepare intercept coal for monthly
- Prepare Statistic Monthly from weekly data
- Make a decision last hole that use for monthly
- Sent to Sr.Database or Computing Geos

2. Minex Data
- Prepare section for monthly (usually in the active area of Exploration)
- Prepare for Seam Outcrop Map
- Sent to Sr.Database or Computing Geos