Process controls in food processing

Module- 9

Lec- 9

Dr. Shishir Sinha

Dept. of Chemical Engineering
IIT Roorkee
 A well designed process ought to be easy to control. More importantly, it is best to consider
the controllability of a process at the very outset, rather than attempt to design a control
system after the process plant has been developed

Objectives of control

• Process control is an integral part of modern processing industries; and the food
processing industry is no exception.
• Process control is to improve the economics of the process by achieving the following
objectives
• To reduce variation in the product
• To quality, achieve more consistent production and maximize yield,
• To ensure process and product safety,
• To reduce manpower and enhance operator productivity,
• To reduce waste and
• To optimize energy efficiency

Mode of operation

Processes are operated under either

• steady state, i.e. process conditions do not change, or unsteady state conditions,
process conditions depend on time.

The latter occurs in most real situations and requires control action in order to keep the
product within specifications.

Two basic steps of any control action

• Accurate measurement of process parameters;

• Manipulation of one or more process parameters using control systems in order to
alter or correct the process behavior.

Measurement of Process Parameters

 • Accurate measurement of the process parameters is absolutely critical for controlling
any process.

Classification of sensors

• Three main classes of sensors used for the measurement of key processing parameters
such as temperature, pressure, mass, material level in containers, flow rate , density,
viscosity, moisture, fat content, protein content, pH, size, color, turbidity etc.
• Penetrating sensors: these sensors penetrate inside the processing equipment and
come into contact with the material being processed.
• Sampling sensors: these sensors operate on samples which are continuously
withdrawn from the processing equipment.
• No penetrating sensors: these sensors do not penetrate into the processing equipment
and, as a consequence, do not come into contact with the materials being processed.

Characterization of sensors according to their applications

• Inline sensors: these form an integral part of the processing equipment, and the values
measured by them are used directly for process control.
• Online sensors: these too form an integral part of the processing equipment, but the
measured values can only be used for process control after an operator has entered
these values into the control system.
• Offline sensors: these sensors are not part of the processing equipment, nor can the
measured values be used directly for process control. An operator has to measure the
variable and enter the values into a control system to achieve process control.

Characteristics to be evaluated before using a sensor

• Response time, gain, sensitivity, ease and speed of calibration,

• Accuracy, stability and reliability,
• Material of construction and robustness and
• Availability, purchase cost and ease of maintenance.
Types of control systems

Control systems can be of two types:

• Manual control and
• Automatic control.

Manual Control

• an operator periodically reads the process parameter which requires to be controlled

and, when its value changes from the set value, initiates the control action necessary
to drive the parameter towards the set value.

Automatic Control

• The process parameters measured by various sensors and instrumentation may be

controlled by using control loops. A typical control loop consists of three basic
components
• Sensor: the sensor senses or measures process parameters and generates a
measurement signal acceptable to the controller.
• Controller: the controller compares the measurement signal with the set value and
produces a control signal to counteract any difference between the two signals.
• Final control element: the final control element receives the control signal produced
by the controller and adjusts or alters the process by bringing the measured process
property to return to the set point, e.g. liquid flow can be controlled by changing the
valve setting or the pump speed.

Classification of an automatic control system

An automatic control system can be classified into four main types:

• on/off (two position) controller
• proportional controller (P-controller)
• proportional integral controller (PI controller)
• proportional integral derivative controller (PID controller).
On/Off (Two Position) Controller

• the simplest automatic controller for which the final control element, e.g. valve, is
either completely open or at maximum, or completely closed or at minimum.
• There are no intermediate values or positions for the final control element.
• FCE,s often experience significant wear, as they are continually and rapidly switched
from open to closed positions and back again.
• on/off controllers are provided with a dead band.
• dead band is a zone bounded by an upper and a lower set point.
• On/off controllers with a dead band are found in many instances in our daily lives:
home heating system, oven, refrigerator and air conditioner.

Advantages of On/Off controllers

• Such controllers have three main advantages:

• low cost,
• instant response and
• ease of operation. However, it is important to ascertain that the upper and lower limit
values are acceptable for a specific process.

Disadvantages of On/Off controllers

• It is not suitable for controlling any process parameter likely to suffer large sudden
deviations from the set point and
• The quality of control is inferior to the continuous controller.
Proportional (P) Controller

• P-controller is one of the most commonly used controllers

• Produces an output signal to the final control element that is proportional to the
difference between the set point and the value of the measured process parameter
given by the sensor (this difference is also known as controller error or offset)
• Mathematically, it can be expressed as:

Where cos(t) COS(NE) + KC Et

COS(t) is the controller output signal at any time t,

COS(NE) is the controller output signal when there is no error,

KC is known as the controller gain or sensitivity (controller tuning parameter) and

Et is the controller error or offset.

Proportional Integral Controller

Output signal to the final control element can be mathematically expressed as:

KC
Where COS ( t )  COS ( NE )  K C Et 
I  E dt
t

τ is a tuning parameter called the reset time; and the remaining notations are same as in P
I

controller equation

Advantage

• The consequence of this is that integral action enables the PI controller to eliminate
the offset, which is the key advantage of the PI controller over a P controller.

Disadvantage

• Two tuning parameters interact and it is difficult to find the ‘best’ tuning values once
the controller is placed in automatic mode.
• A PI controller increases the oscillatory behavior.

Proportional Integral Derivative Controller

• Output signal to the final control element can be mathematically expressed as:
KC dE
COS(t )  COS( NE )  K C Et 
I  Et dt  K C  D t
dt

• Where τ is a new tuning parameter called the derivative time; and the remaining
D

notations are already explained above.

• Higher values of D provide a higher weighting to the fourth, i.e. derivative term
which determines the rate of change of the controller error (Et) whether Et is positive
or negative.
Advantage

• The introduction of the derivative term, is that it modifies the drawback of the PI
controller
• it works to decrease the oscillating behavior of the measured process parameter.
• A properly tuned PID controller action can achieve a rapid response to error
(proportional term), offset elimination (integral term) and minimize oscillations
(derivative term).

Disadvantage

• The key disadvantage of the PID controller is that it has three tuning parameters,
which interact and must be balanced to achieve the desired controller performance as
it is often hard to determine which of the three tuning parameters is dominantly
responsible for an undesirable performance.

Process Control in Modern Food Processing

• Control applications in food processing can be discussed in the context of three

categories of products:
• Bulk commodity processing, e.g. grain milling, milk, edible oil, sugar and starch
production, where control is arguably most advanced,
• Manufactured products, e.g. pasta, cheese, in-container and aseptically processed
products, and
• Products which have been subjected to processing methods essentially designed to
retain their original structure, e.g. meat, fish, fruits and vegetables.

Programmable Logic Controller

• It is a microprocessor-based system which can communicate with other process

control components through data links. PLCs commonly use the so called ladder logic
which was originally developed for electrical controls using relay switches.
Supervisory Control and Data Acquisition

• The supervisory control and data acquisition (SCADA) system is not a full control
system, but is a software package that is positioned at a supervisory level on top of
hardware to which it is interfaced, generally via PLCs, or other hardware modules.

Manufacturing Execution Systems

These are software packages which have been used for a number of years in process
industries to support key operations and management functions ranging from data
acquisition to maintenance management, quality control and performance analysis.
References

 http://www.google.co.in/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&v
ed=0CCkQFjAA&url=https%3A%2F%2Fround-lake.dustinice.workers.dev%3A443%2Fhttp%2Fwww.pbf.unizg.hr%2Fhr%2Fcontent%2Fdo
wnload%2F9507%2F46413%2Fversion%2F1%2Ffile%2Fcontrol%2Bstrategy%2Bin
%2Bfood%2Bindustry.pdf&ei=IhnzUtKPFYvMkAXkl4HwAg&usg=AFQjCNHA60f
icLRg8LfIgjoO0nVZOlzziQ&sig2=72PtBNrZ1f1QN-X3bQg4uQ
 http://practicalaction.org/quality-control-in-food-processing
 http://www.ces.ncsu.edu/depts/foodsci/ext/pubs/scheduledprocesses.PDF
 http://www.fda.gov/iceci/inspections/inspectionguides/ucm074955.htm
 http://onlinelibrary.wiley.com/doi/10.1002/9783527634361.ch18/summary